Question about the collection of NETWORK adapters / collage

Similar Questions

• Question about the collection of NETWORK adapters for vMotion / VM vSwitch

  Hello

  We use vSphere Enterprise Edition 5.1.

  We also create separate vSwitch for management / vMotion and VM.

  Each vSwitch receives 2 network cards connected to the different switch for redundancy.

  We would like to know is necessary to provide the collection of NETWORK adapters for these vSwitches?  Currently, only enable us NIC Teaming for VM vSwitch only.

  Thank you

  VSwitch vMotion, we have 2 assigned NIC (nic2 and nic6) with 10 VLANS.  NIC2 and nic6 are connected to 2 different physical switches.

  Should I choose

  (1) both are active

  (2) both are assets + grouping of NETWORK cards?

  Question - if there is only 1 VLAN, it seems that NIC Teaming is also not very useful unless we use 2 VLAN (Multi-NIC vMotion).  Is this right?

  If you use Multi-NIC vMotion, there is no need to have two different VLANS, all you need is depending on configuration

  on your vMotion switch, please create two vmkernel port for vMotion with the same VLAN ID, but the grouping of NETWORK cards as below

  vMotion_1 - VLAN ID: 10

  Grouping of NETWORK cards

  vmnic2 - active

  vmnic6 - watch

  vMotion_2 - VLAN ID: 10

  vmnic6 - active

  vmnic2 - watch

• Question about wireless, routers and network adapters... hope is the right place for the?

  I have a modem to my cable service and I was told that I could network 4 (3 desktop computers and 1 laptop) computers. I plugged the modem, I plugged the router up... i put in the disc of the cable operator to make the wireless network and it does not connect them for some reason any. the cable service representative didn't tell me, I would need something more, but would need one of these network adapters wireless that goes into the USB port on the back? the computer on which the modem is hung up works fine... it's one of those self install the things I told them that I'd rather have a tech cling to me but they insisted that I could do... (obviously any fool can do, I'm not a fool... I'm just stupid! lol "title =" Smiley Tongue"/ > can someone just tell me if I would need one of the cards or y at - it a way to tell if my computers are ready for the wireless... I have 2 dimension E310 XP media center copmputers... is tehre a way to check whether she would need the adapter or not... hope I explained everything properly...) Thank you bunches! antkaki [renee]

  third time to post my question, don't know why it is being deleted... someone can let me know?  Thanks again

  
  

• ESXi 3.5 U5 - best practices for the collection of NETWORK adapters

  Hello

  I'm using ESXi 3.5 U5 installed on a Dell PowerEdge R710.

  This server has 4 NETWORK cards

  I want team two network adapters to the default value 0 of the Virtual Switch.

  What are the best practices to achieve this?

  mdsuser wrote:

  I want team two network adapters to the default value 0 of the Virtual Switch.

  What are the best practices to achieve this?

  It depends on what you want to achieve. Fault tolerance, the aggregation?

  Take a look at this document from VMware.

  If you use your search engine of the day and throw it into the words "VMware ESX" and add circuits or consolidation, there will be some hits on various blogs showing solutions to different hardware (in collaboration with Cisco, HP switches).

  Addition:

  This page will also give you an overview of the different types of networking topics virtual.

• Configure the collection of NETWORK adapters in Production Env.

  In my current setup of vSwitch 0 I have 1 uplink for my port VM group and I would like to add another, aka grouping of NETWORK cards. Once I have do my physical connection of my host to my pSwitch & adapt my vSwitch settings to use the second uplink, does this take effect immediately or the host must it be robooted to make it work?

  ESXi 4.1

  Hello.

  It will take effect immediately.

  Good luck!

• How is the collection of NETWORK adapters?

  I know it's possible to have 2 NICs for the network of the VM, but is it as simple as the addition of 2 NICs for the VM network? Because I notice that once I reboot my ESX 4.0 host, cluster VM network will not work. Do I need to do any configuration on the switch (s) these 2 network cards connected to as well?

  Also, is it possible to configure or select the team to have 1 active and standby 1 or load balancing?

  PortFast is configured on the physical switch indeed. For some reason any I doubt this is the problem that you are experiencing.

  Can you detail your config:

  vSwitch - attached NICS - circuits - load balancing

  Duncan

  VMware communities user moderator | VCP | VCDX

  -

• Question about the collection

  I'm in bulk data collection in an associative array called v_tb_bw_lg_mstr twice. However, both the last index value is the same.

  DECLARE
    TYPE typ_tb_bw_lg_mstr IS TABLE OF tb_bw_lg_mstr%ROWTYPE INDEX BY BINARY_INTEGER;
    v_tb_bw_lg_mstr typ_tb_bw_lg_mstr;
    v_sql VARCHAR2(64);
  BEGIN
       
    SELECT * BULK COLLECT
    INTO v_tb_bw_lg_mstr
    FROM tb_bw_lg_mstr;
    
    Dbms_output.put_line('Output 1:'||v_tb_bw_lg_mstr.LAST);
    
    SELECT * BULK COLLECT
    INTO v_tb_bw_lg_mstr
    FROM tb_bw_lg_mstr;
    
    Dbms_output.put_line('Output 2:'||v_tb_bw_lg_mstr.LAST);
  
  EXCEPTION
    WHEN OTHERS THEN
    ROLLBACK;
    Dbms_output.put_line(SQLERRM);
  END;
  /

  Output 1:2430
  Output 2:2430

  Because the second SELECT is not an addition to an existing collection, it just overwrites it.

  To get what you want, this could be the most effective way:

    SELECT * BULK COLLECT
    INTO v_tb_bw_lg_mstr
    FROM tb_bw_lg_mstr
    UNION ALL
    SELECT *
    FROM tb_bw_lg_mstr;
  

• Questions about the collection of personalization data.

  I am currently working on a form which is presented as an xml file using a submit button by email.  There are several things that I wonder if you can customize and if so, how?

  1. Is it possible to have the calculated time field that is included in the exported data?
  2. IF SO... Is it possible to change the date/time calculated field to calculate when the e-mail button is clicked rather than when the form is started?
  3. Is it possible to have the file by e-mail named something other than * name * _data?  Maybe something that includes the date, or another domain specified for point more precisely what form it is?
  4. Finally, is it possible when you import data to import xml data into an Excel file which already has other data collected in it?

  Responses to the foregoing would be greatly appreciated!

  Thank you!

  Kayla

  Hey Kayla,

  Yes, most of it is possible.

  1: select the date/time field and go to object > tab. Liaison depending on the version of LC designer you have, you want the drop-down list of data binding to have 'Normal' or 'using the name '. This means that the value is exported to the XML file. If the drop-down list says "No data binding" or "None", the value will not be exported.

  2: the date/time field probably has the script initialization or docReady. That's fine, the date and time will be filled when the form is opened. In order to refresh the time at the time wherever the user submits the form, you must include the following line in the mouseDown event of the submit button.

  DateTimeField1.execEvent("initialize"); 
  

  This will trigger the DateTime field Initialize event and update the date / time just before submitting the form.

  3: it's tricker, the name of the XML file is set automatically to reflect the name of the file of the form. You can write the script to change the name of the file of form (and by extension the name of the XML file), however, this requires a function of trust in a separate javascript file. This JS file will have to be on all computers which would be used to access the form and to be honest not worth the (significant).

  4: adobe do a good job, if you are distributing your form via Acrobat.com. Additionally, Acrobat version 9 allows you to select the individual xml files and export them to an Excel spreadsheet (under the menu options). You can also compile returned forms by selecting the answer file and the individual xml files. I don't think that you will be able to export a new XML responses in an existing worksheet. Using Excel, you may be able to import the new XML into the existing file. If all else fails, I export the new xml to spreadsheet files, this open in Excel and copy the data back. Open the existing worksheet, and then copy the data back at the end of the table.

  Hope that helps,

  Niall

• Physical requirements for the collection of network adapters

  During the aggregation of physical NIC cards on a host ESX (i) the physical switches that NICs are connected to have all of its ports are associated as well?

  Thank you

  Real grouping only with the IP hash and require a specific configuration also on physical switches.

  To keep things simple, I suggest using the default grouping policy (it's just a load balancing solution) which works very well with all kinds of switches.

  André

• Question about the differences in commands

  Hey guys -.

  I just had a few questions about the differences between orders that seem to perform the same function.  Can you let me know if an order is more preferable to the other and what the difference is.  I would really appreciate it as it I currently practice some INE laboratories and I see that orders change from lab to lab.  Thanks advance!

  1. When you write a static NAT for specific host 1 - is - this important if I understand the 32 subnet?

  EX: static (inside, outside) 1.1.1.1, 2.2.2.2 VS static (inside, outside) 1.1.1.1 2.2.2.2 netmask 255.255.255.255

  2. when I'm setting up a router as a CA server and it is necessary to "export" the key, whatever my method of exporting the key?  If so, in which method call for which solution?

  EX: key export cryptographic rsa ciscox pem URL nvram: cisco VS. exporting key 3des cryptographic ciscox pem 3des rsa terminal cisco

  3. If I have to mark a packet with a DSCP of X value, matter if I use the 'set dscp' VS 'set ip dscp?  If so, what is the difference?

  FXY

  Policy-map X

  class X

  the dscp X value

  VS

  Policy-map X

  class X

  X ip dscp value

  I guess pertaining to 2, if i was speaking in terms of from a cisco router to another cisco router - would terminal be acceptable?
  
  

  Yes, the "Import cryptographic key" command can take a url and also from the terminal entrance. In this terminal case wil is much easier.

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• I have a question about the functionality of Oracle Identity Manager...?

  Hi friends
  I have a question about the features of Oracle Identity Manager.
  Here's my question:
  Self-management is possible network passwords (reset / unlock) with Oracle Identity Manager 9.1.0.2
  
  Very grateful.

  What Kevin suggested this means that you are managing accounts and their password by IOM. If your condition is the same then follow:

  Re: error during password reset using the self-service portal

• A few questions about the difference between the Satellite P70, L70, S70

  Hello, I have a lot of questions about the P70, L70, S70 series that come with a 1920 x 1080 panel.

  (1) what are the differences between the L70 and S70 series? With the exception of the RAM and HARD drive capacity, books seem pretty identical.

  (2) P70, L70, S70 doesn't support a 2nd HARD drive or it's just the P70 series that support?

  (3) all the three (P70, L70, S70 series) come with the same TFT panels?

  (4) of the above series, which supports mSata?

  (5) all the model of each series are delivered with support from mSata? For example, it could be that L70 - a - 13 m supports mSata is not the case of the L70-a-146?

  (6) all the foregoing, are delivered with a S - ATA II or III S - ATA interface?

  (7) who is the best of these series listed? I'm trying to understand what makes the big difference of S70 to P70 except for the envelope for example.

  Thank you in advance.

  > (1) what are the differences between the series L70 and S70? With the exception of the RAM and HARD drive capacity, books seem pretty identical.

  What models Sat L70 and S70 do you mean exactly? There are different L70-xxx-xxx and S70 models on the market that supports different hardware specifications.

  (> S70 2) P70, L70, support a 2nd drive HARD or is - it just the series P70 that support?
  As you can see in this [Sam P70 HDD replacement document, | http://aps2.toshiba-tro.de/kb0/CRU3903II0000R01.htm] the P70 series supports the 2nd drive Bay HARD, BUT even if there is a 2nd HARD drive Bay, this does not mean that you can use the 2nd HARD drive. In the case where the 2nd HARD drive Bay are equipped with HARD drive connector, you can use the 2nd HARD drive

  I also found the [Sam L70/S70 HDD replacement | http://aps2.toshiba-tro.de/kb0/CRU3703HG0000R01.htm] the document on the Toshiba page and there I see this 2nd HARD drive Bay is not available

  (> 3) all three (P70, L70, S70 series) come with the same TFT panels?
  See point 1). Different P70, L70, S70 models were equipped with different material parts.

  (> 4) of the series above, which takes in charge mSata?
  As far as I know that some P70 models are equipped with an mSATA SSD of 256 GB.

  (> 5) do all the model of each series are delivered with support mSata? For example, it could be that L70 - a - 13 m supports mSata is not the case of the L70-a-146?
  See point 4) not all models supports the same hardware specifications

  (> 6) all of the above, come with a S - ATA II or III S - ATA interface?
  I don t think that SATA III is supported. I guess it would be SATA II

  (> 7) which is the best of these series listed? I'm trying to understand what makes the big difference of S70 to P70 except for the envelope for example.
  Not easy to answer because there are too many models released in Europea.
  And not all models are available in each country. So I guess you will have to look for the models that have been released in your country.

• A few questions about the upgrade on Satellite A300-144

  Sorry for the typos, English is not my mother tongue.
  I want to ask some questions about the upgrade of a300-144.

  * Some info first.*

  CPU: T2370 ([http://ark.intel.com/products/34445/Intel-Pentium-Processor-T2370-1M-Cache-1_73-GHz-533-MHz-FSB]).
  Chipset: GM965 ([http://ark.intel.com/products/29821/Intel-82GM965-Graphics-and-Memory-Controller]).

  * Questions.*

  1. my frequency of laptop memory at 533 MHz, supports 667 MHz memory controller, memory modules can work at 667 MHz. Is - this because CPU FSB 533 MHz frequency and new processor at 667/800 MHz FSB will fix it or it is hardcoded in the BIOS?

  2 Intel said that the size of max memory for my chipset is 4 GB (2 x 2 GB), but Toshiba says that only 2 GB (2 x 1 GB), who is right?

  3 I know, taken of my CPU is μFCPGA-478 aka socket P, max FSB 800 MHz, max 35 W TDP, so T9500 ([http://ark.intel.com/products/33918/Intel-Core2-Duo-Processor-T9500-6M-Cache-2_60-GHz-800-MHz-FSB]) is a compatible processor or there are some limitations in the BIOS?

  > 1. My frequency of laptop memory at 533 MHz, supports 667 MHz memory controller, memory modules can work at 667 MHz. Is - this because CPU FSB 533 MHz frequency and new processor at 667/800 MHz FSB will fix it or it is hardcoded in the BIOS?

  The speed of the memory is related on the material. This means that the FSB is responsible for the limitation.
  If the FSB would allow support 667 MHz then the memory would also at this speed.

  > 2. Intel says that the size of max memory for my chipset is 4 GB (2 x 2 GB), but Toshiba says that only 2 GB (2 x 1 GB), who is right?
  The memory depends on the chipset. So if the chipset supports 4 GB of RAM, you should be capable of this move to 4 GB of RAM

  > 3. I know, my CPU is? FC-PGA-478 aka socket P, max FSB 800 MHz, max 35 W TDP, so T9500 (http://ark.intel.com/products/33918/Intel-Core2-Duo-Processor-T9500-6M-Cache-2_60-GHz-800-MHz-FSB) will be a compatible processor or there are some limitations in the BIOS?

  It might be possible that the new processor would be fully supported by the BIOS, but in most cases it should not be a problem if the chipset would support the new processor.
  But as far as I know the upgrade of the CPU is not supported by Toshiba or any other manufacturers of portable and its your own risk to run laptop with the new processor.

• Question about the recovery partition

  Hello.

  I have a question about the recovery of HARD drive partition.

  If I do the operation to clear the hard disk option in the wizard it will remove * all * or it will keep my partition recovery in this way I can come back later. I want to know because I would like to put on a different OS.

  I know he said he would, but caution in the PDF, I found it says that on a normal recovery too (that he would remove each partition) and I'm a little confused about how the recovery actually worked.

  Thank you.

  Hey Buddy,

  To be honest I n don't know what you mean exactly with this option to erase.

  In General, Toshiba Recovery disk will wipe your entire HDD to restore factory settings correctly. This means that if you start from that disk and follow the instructions on the screen, everything will be removed.

  In addition, the recovery disk doesn t create a recovery partition. It is not available. Disk copy just the files on the second partition in folder HDDrecovery to start an installation of HARD drive recovery.

• A few questions about the Satellite A100 PSAANE

  Hi friends,

  I have a Toshiba Satellite A 100 - PSAANE with Vista Home Basic preinstalled in it.
  Now, I have a few questions... I mention below: -.

  (1) if I want to format my laptop, I need a CD to install for Vista Home basic... then I don't have this Toshiba CD when I bought the laptop. So how do? question: How can I format it?

  (2) can I change my Vista Home Basic to windows XP? I think it's much faster than this one. is it advisable?

  (3) I have a GB of RAM in the laptop. Increase the RAM? I think that my laptop has become to slow down. is it advisable?

  (4) and on my screen, everytime I try to change my profile screen to windows Classic view, my screen begins to blink. and after a while, the screen turns off. So I can't change that. I put the color scheme of windows vista only. What to do about that?

  Please help me friends. Thanks in advance.

  Kind regards
  Perkins

  Hello

  Here, a few questions about the number:

  (1) usually, you should get the Vista Toshiba Recovery DVD. If you didn t receive this DVD then you can order it here https://backupmedia.toshiba.eu/landing.aspx or you could install the disc of Microsoft Vista.

  (2) of course, you can do this. I think that Win XP drivers can be downloaded from the Toshiba driver page.

  (3) Yes, you can upgrade the RAM. For more information, see your manual or search on this forum for similar topics

  (4) maybe it s associated with the graphics driver. Check if you can update. I would recommend additional check if you are using the latest version of the BIOS

  Welcome them