Question about the collection

Similar Questions

• Question about the collection of NETWORK adapters for vMotion / VM vSwitch

  Hello

  We use vSphere Enterprise Edition 5.1.

  We also create separate vSwitch for management / vMotion and VM.

  Each vSwitch receives 2 network cards connected to the different switch for redundancy.

  We would like to know is necessary to provide the collection of NETWORK adapters for these vSwitches?  Currently, only enable us NIC Teaming for VM vSwitch only.

  Thank you

  VSwitch vMotion, we have 2 assigned NIC (nic2 and nic6) with 10 VLANS.  NIC2 and nic6 are connected to 2 different physical switches.

  Should I choose

  (1) both are active

  (2) both are assets + grouping of NETWORK cards?

  Question - if there is only 1 VLAN, it seems that NIC Teaming is also not very useful unless we use 2 VLAN (Multi-NIC vMotion).  Is this right?

  If you use Multi-NIC vMotion, there is no need to have two different VLANS, all you need is depending on configuration

  on your vMotion switch, please create two vmkernel port for vMotion with the same VLAN ID, but the grouping of NETWORK cards as below

  vMotion_1 - VLAN ID: 10

  Grouping of NETWORK cards

  vmnic2 - active

  vmnic6 - watch

  vMotion_2 - VLAN ID: 10

  vmnic6 - active

  vmnic2 - watch

• Question about the collection of NETWORK adapters / collage

  When installing ESXi, I want to use all 4 GigE ports on my server and I put a static IP address for each NIC.  Once the server is in place, I bind two NICs.  What I want to know is, it is best to remove the IP address for the second NETWORK card in our DNS?  For example, after you install ESXI, our DNS has the following:

  esxi1.mycompany.local 10.10.0.111

  esxi1.mycompany.local 10.10.0.112

  Should I delete the 10.10.0.112 entry if the servile pair use 10.10.0.111?  I think that I should so that there is no misdirection, but I'm not sure.

  Any suggestion would be appreciated.

  So phyical NIC have IP addresses assigned to ESXi.  You say ESXi which physical network cards must be plugged into the virtual switch and you assign an IP to the network management agent who is also trendy that same virtual switch, but never you assign IP addresses to physical network interface cards.  The sole purpose of a phyical in an ESXi installation nic is so they can connect to the virtual switches that you create within your ESXi installation.  Then it's the other virtual machines and VMKernel ports that have their own IP address.  Take this picture below, that I found on the internet for example.  These (vmnic0 and vmnic1) physical network interface cards have not all ip addresses, there is no record of A DNS pointing to those, etc..  They are there to connect physical switches on your virtual switches (they are network devices; it is the clearest way to think about).  The gray bar below is a virtual switch and the green dots on the virtual switch are ports where something is plugged.  These virtual machines (Linux, Windows, whatever), that's what has ipaddresses.  The special devices plugged into the virtual switch are called Service Console and VMKernel Ports (in ESXi 4.x, they are all just called VMKernel Ports).  These have IP addresses and these are the closest things to what you describe in your message.

  If you get the chart however, you will notice that the virtual switch "obligations" say these two NICs phy, together based on how it to bind to them.  Unless you want to do a lot of research, or you have an exceptional case complex parameters for pasting of these two NICs (in the tab "NIC Teaming") should probably be "Route based on the original virtual port code" and "link status only.  Lighthouse of probing should be used in cases when the status link only mode does not work (usually he does it very well).  Moreover I also put the two cards as 'Active' network and say yes to "Warn switch" and "rescue".

• Questions about the collection of personalization data.

  I am currently working on a form which is presented as an xml file using a submit button by email.  There are several things that I wonder if you can customize and if so, how?

  1. Is it possible to have the calculated time field that is included in the exported data?
  2. IF SO... Is it possible to change the date/time calculated field to calculate when the e-mail button is clicked rather than when the form is started?
  3. Is it possible to have the file by e-mail named something other than * name * _data?  Maybe something that includes the date, or another domain specified for point more precisely what form it is?
  4. Finally, is it possible when you import data to import xml data into an Excel file which already has other data collected in it?

  Responses to the foregoing would be greatly appreciated!

  Thank you!

  Kayla

  Hey Kayla,

  Yes, most of it is possible.

  1: select the date/time field and go to object > tab. Liaison depending on the version of LC designer you have, you want the drop-down list of data binding to have 'Normal' or 'using the name '. This means that the value is exported to the XML file. If the drop-down list says "No data binding" or "None", the value will not be exported.

  2: the date/time field probably has the script initialization or docReady. That's fine, the date and time will be filled when the form is opened. In order to refresh the time at the time wherever the user submits the form, you must include the following line in the mouseDown event of the submit button.

  DateTimeField1.execEvent("initialize"); 
  

  This will trigger the DateTime field Initialize event and update the date / time just before submitting the form.

  3: it's tricker, the name of the XML file is set automatically to reflect the name of the file of the form. You can write the script to change the name of the file of form (and by extension the name of the XML file), however, this requires a function of trust in a separate javascript file. This JS file will have to be on all computers which would be used to access the form and to be honest not worth the (significant).

  4: adobe do a good job, if you are distributing your form via Acrobat.com. Additionally, Acrobat version 9 allows you to select the individual xml files and export them to an Excel spreadsheet (under the menu options). You can also compile returned forms by selecting the answer file and the individual xml files. I don't think that you will be able to export a new XML responses in an existing worksheet. Using Excel, you may be able to import the new XML into the existing file. If all else fails, I export the new xml to spreadsheet files, this open in Excel and copy the data back. Open the existing worksheet, and then copy the data back at the end of the table.

  Hope that helps,

  Niall

• A few questions about the difference between the Satellite P70, L70, S70

  Hello, I have a lot of questions about the P70, L70, S70 series that come with a 1920 x 1080 panel.

  (1) what are the differences between the L70 and S70 series? With the exception of the RAM and HARD drive capacity, books seem pretty identical.

  (2) P70, L70, S70 doesn't support a 2nd HARD drive or it's just the P70 series that support?

  (3) all the three (P70, L70, S70 series) come with the same TFT panels?

  (4) of the above series, which supports mSata?

  (5) all the model of each series are delivered with support from mSata? For example, it could be that L70 - a - 13 m supports mSata is not the case of the L70-a-146?

  (6) all the foregoing, are delivered with a S - ATA II or III S - ATA interface?

  (7) who is the best of these series listed? I'm trying to understand what makes the big difference of S70 to P70 except for the envelope for example.

  Thank you in advance.

  > (1) what are the differences between the series L70 and S70? With the exception of the RAM and HARD drive capacity, books seem pretty identical.

  What models Sat L70 and S70 do you mean exactly? There are different L70-xxx-xxx and S70 models on the market that supports different hardware specifications.

  (> S70 2) P70, L70, support a 2nd drive HARD or is - it just the series P70 that support?
  As you can see in this [Sam P70 HDD replacement document, | http://aps2.toshiba-tro.de/kb0/CRU3903II0000R01.htm] the P70 series supports the 2nd drive Bay HARD, BUT even if there is a 2nd HARD drive Bay, this does not mean that you can use the 2nd HARD drive. In the case where the 2nd HARD drive Bay are equipped with HARD drive connector, you can use the 2nd HARD drive

  I also found the [Sam L70/S70 HDD replacement | http://aps2.toshiba-tro.de/kb0/CRU3703HG0000R01.htm] the document on the Toshiba page and there I see this 2nd HARD drive Bay is not available

  (> 3) all three (P70, L70, S70 series) come with the same TFT panels?
  See point 1). Different P70, L70, S70 models were equipped with different material parts.

  (> 4) of the series above, which takes in charge mSata?
  As far as I know that some P70 models are equipped with an mSATA SSD of 256 GB.

  (> 5) do all the model of each series are delivered with support mSata? For example, it could be that L70 - a - 13 m supports mSata is not the case of the L70-a-146?
  See point 4) not all models supports the same hardware specifications

  (> 6) all of the above, come with a S - ATA II or III S - ATA interface?
  I don t think that SATA III is supported. I guess it would be SATA II

  (> 7) which is the best of these series listed? I'm trying to understand what makes the big difference of S70 to P70 except for the envelope for example.
  Not easy to answer because there are too many models released in Europea.
  And not all models are available in each country. So I guess you will have to look for the models that have been released in your country.

• A few questions about the upgrade on Satellite A300-144

  Sorry for the typos, English is not my mother tongue.
  I want to ask some questions about the upgrade of a300-144.

  * Some info first.*

  CPU: T2370 ([http://ark.intel.com/products/34445/Intel-Pentium-Processor-T2370-1M-Cache-1_73-GHz-533-MHz-FSB]).
  Chipset: GM965 ([http://ark.intel.com/products/29821/Intel-82GM965-Graphics-and-Memory-Controller]).

  * Questions.*

  1. my frequency of laptop memory at 533 MHz, supports 667 MHz memory controller, memory modules can work at 667 MHz. Is - this because CPU FSB 533 MHz frequency and new processor at 667/800 MHz FSB will fix it or it is hardcoded in the BIOS?

  2 Intel said that the size of max memory for my chipset is 4 GB (2 x 2 GB), but Toshiba says that only 2 GB (2 x 1 GB), who is right?

  3 I know, taken of my CPU is μFCPGA-478 aka socket P, max FSB 800 MHz, max 35 W TDP, so T9500 ([http://ark.intel.com/products/33918/Intel-Core2-Duo-Processor-T9500-6M-Cache-2_60-GHz-800-MHz-FSB]) is a compatible processor or there are some limitations in the BIOS?

  > 1. My frequency of laptop memory at 533 MHz, supports 667 MHz memory controller, memory modules can work at 667 MHz. Is - this because CPU FSB 533 MHz frequency and new processor at 667/800 MHz FSB will fix it or it is hardcoded in the BIOS?

  The speed of the memory is related on the material. This means that the FSB is responsible for the limitation.
  If the FSB would allow support 667 MHz then the memory would also at this speed.

  > 2. Intel says that the size of max memory for my chipset is 4 GB (2 x 2 GB), but Toshiba says that only 2 GB (2 x 1 GB), who is right?
  The memory depends on the chipset. So if the chipset supports 4 GB of RAM, you should be capable of this move to 4 GB of RAM

  > 3. I know, my CPU is? FC-PGA-478 aka socket P, max FSB 800 MHz, max 35 W TDP, so T9500 (http://ark.intel.com/products/33918/Intel-Core2-Duo-Processor-T9500-6M-Cache-2_60-GHz-800-MHz-FSB) will be a compatible processor or there are some limitations in the BIOS?

  It might be possible that the new processor would be fully supported by the BIOS, but in most cases it should not be a problem if the chipset would support the new processor.
  But as far as I know the upgrade of the CPU is not supported by Toshiba or any other manufacturers of portable and its your own risk to run laptop with the new processor.

• Question about the recovery partition

  Hello.

  I have a question about the recovery of HARD drive partition.

  If I do the operation to clear the hard disk option in the wizard it will remove * all * or it will keep my partition recovery in this way I can come back later. I want to know because I would like to put on a different OS.

  I know he said he would, but caution in the PDF, I found it says that on a normal recovery too (that he would remove each partition) and I'm a little confused about how the recovery actually worked.

  Thank you.

  Hey Buddy,

  To be honest I n don't know what you mean exactly with this option to erase.

  In General, Toshiba Recovery disk will wipe your entire HDD to restore factory settings correctly. This means that if you start from that disk and follow the instructions on the screen, everything will be removed.

  In addition, the recovery disk doesn t create a recovery partition. It is not available. Disk copy just the files on the second partition in folder HDDrecovery to start an installation of HARD drive recovery.

• A few questions about the Satellite A100 PSAANE

  Hi friends,

  I have a Toshiba Satellite A 100 - PSAANE with Vista Home Basic preinstalled in it.
  Now, I have a few questions... I mention below: -.

  (1) if I want to format my laptop, I need a CD to install for Vista Home basic... then I don't have this Toshiba CD when I bought the laptop. So how do? question: How can I format it?

  (2) can I change my Vista Home Basic to windows XP? I think it's much faster than this one. is it advisable?

  (3) I have a GB of RAM in the laptop. Increase the RAM? I think that my laptop has become to slow down. is it advisable?

  (4) and on my screen, everytime I try to change my profile screen to windows Classic view, my screen begins to blink. and after a while, the screen turns off. So I can't change that. I put the color scheme of windows vista only. What to do about that?

  Please help me friends. Thanks in advance.

  Kind regards
  Perkins

  Hello

  Here, a few questions about the number:

  (1) usually, you should get the Vista Toshiba Recovery DVD. If you didn t receive this DVD then you can order it here https://backupmedia.toshiba.eu/landing.aspx or you could install the disc of Microsoft Vista.

  (2) of course, you can do this. I think that Win XP drivers can be downloaded from the Toshiba driver page.

  (3) Yes, you can upgrade the RAM. For more information, see your manual or search on this forum for similar topics

  (4) maybe it s associated with the graphics driver. Check if you can update. I would recommend additional check if you are using the latest version of the BIOS

  Welcome them

• Re: Several questions about the recovery of the Satellite L750 features

  I have several questions about the recovery of Satellite L750 features available to it. Any help and answers would be useful.

  (1) when I started the laptop first, he asked me to create a recovery CD incase I need to reinstall the operating system. But he also said that he built in the recovery partition, so therefore, I have to make a recovery cd or not?

  (2) will be the recovery CD is exactly the same as the recovery on the system partition?

  (3) is the partion of CD or recovery includes all the integrated software pre-installed with the laptop?

  (4) also in the device manage management it shows watch partion recovery but it is empty, is it true?

  (5) in the second partition (drive D) system, he has a record with what looks like the recovery of files and folders. Is it safe to move/remove it?

  Hello

  I'll try to provide answers:
  1 - to ensure that everything works perfectly you don t need these discs, but if something goes wrong with the HARD drive you will not be able to do anything. When you have the recovery DVDs, you will still be able to install the recovery image and once again the factory settings. So my advice to you is: create these discs as soon as possible. Use only on DVD-R media and buy products of high quality (TDK or Verbatim).
  2 - Yes.
  3 - Yes.
  4 - No. Don t be confused with this.
  5. in a first time create restore DVD, and later you can do what you want. I put t know which files mean you but don t touch anything before that of the recovery disks to be created.

  In the past, many people have been experimenting with the structure of HARD drive and partitions and later was surprised when installing disk recovery HARD has been damaged. Don t make the same mistake.

  If you have any other questions you are welcome.

• Question about the new Yoga 10 HD +.

  Hello

  A few questions about the new Yoga 10 HD + that I hope you can answer.

  I bought the former model, last year. Love the design and long battery life, but a few major questions made me return.

  • Somewhere that I've read that it can not read NTFS on USB so I guess that's the same thing with a NTFS formatted microSD card?
  • Can it read exFAT formatted microSD cards?
  • Anyone who has questions about the audio via bluetooth?
    (I know that BT is not exactly High End HiFi but the old 10 Yoga for some obscure reason - most likely a driver problem which nobody cared to fix - rang * very * worst with visibly distortion while both my phone and a Tablet noname cheap I have zero about fidelity - any of my devices bluetooth audio) I tried aptX or not)

  So to avoid buying it back it also I really I would like to see if I can get my questions answered before buy you.

  While I love the form factor and long term issues above are only two Mayor dealbreakers for me. Bad audio quality = no joy listen to spotify, local etc. MP3s. not of NTFS or exFAT = some great movies.

  My old noname android Tablet really could use an upgrade so I'm really curious it may be, or I should watch the competition and will be form factor and battery LIFE.

  Thanks in advance.

  EDIT:

  If it does not support NTFS or exFAT on microSD card have someone at - he tried ext3 or ext4?

  I mean with Linux Android root, it should be a no-brainer to support at least when it comes to royalties unlike NTFS or exFAT where it * might * have some trouble with Microsoft.

  I used a USB through a USB OTG cable. NTFS or exFAT have been recognized by the Tablet PC. FAT32 is seems to be the preference.

• I have a question about the time machine. I recently updated my Quicken 2015 and there was something wrong with the update. Can I go back in just the Quicken file and restore it until I downloaded the update do I have to restore the entire

  I have a question about the time machine. I recently updated my Quicken 2015 and there was something wrong with the update. Can I come back in all the Quicken file and restore from time Machine before I downloaded the update to do, I need to restore the entire computer?

  Yes, you can just restore this file or application. Use Time Machine to back up or restore your Mac - Apple Support

• Just a quick question about the appearance of the cluster

  Hello, this is Matthew, just a quick question about the appearance of the cluster

  Is there anyway to rearrange the order of the elements? I know cutting automatic resizing, I could move the items by hand. But if I use the cluster somewhere else, I have to move the items again...

  What I want is of the order of "Mx My Mz Ax Ay Az Temp voltage CS".

  Is there a quicker way to deal with?

  THz so much!

  You can right-click the border of the cluster and choose "arrange control cluster...". "The user interface is not as intuitive as it could be, but it will allow you to reorder items. If you use the cluster in several places, you should make the cluster in a type definition and replace all current uses of the latter with the type definition, so that they all match. They will also update automatically when you make changes to the type definition. Otherwise, you could have a situation where you have multiple groups with the same data types, but with elements in a different order, and your data will be getting a new denominated, when wire you the whole clusters. The data will be in the same order, but given that the item labels are in a different order, you can't get the data you want, when ungroup you by name.

• A few questions about the use of data and Cliq

  I have the cliq, however I chose to not get 3G (so I bought full fare). So I have a few questions about the phone and the use of 3G / 2 G/Edge:

  1 - is possible to disable completely the 2G / 3 G/Edge? I know you can switch between them, but are anyway just tell the phone to stop using them altogether since I'm not subbed to the service?

  2. when the update takes place, I guess we'll have to reconnect motoblur and etc, but if I don't have 3 G will I have motoblur connection problems after the update? Or he keeps the latest wifi settings so that it would connect to wifi to connect. When I first got my phone it was not a problem b/c I had 3G for the first month.

  I hope that makes sense, thanks!

  To stop all the data, I would like to download an application called APNDroid. He cut them all down. When you log on to blur you have 3G or WIFI doe this without getting a timeout error. During the process of setting up your Blur account, you can press the menu button and set up your wifi to work, this will connect you to Blur and your phone will be connected to the blur. If I were you I would be rethinking to do a data plan since you are really losing out on most of your main features of phones. It's your choice, however.

• Is it a good place to ask questions about the slow s Tablet touchscreen response?

  Is it a good place to ask questions about the slow s Tablet touchscreen response?

  You experience slow response on normal s tablet, the first gen one or the Xperia s tablet, a new.

  If you experience a slow response, it may be because you use too many apps at the time and slowing down of your tablet. How long it lasts?

• Questions about the Windows Feedback program Fullfillment

  When will I know if my fullfillment of windows feedback program is over, that I have installed on my PC?

  Hello mpic16,

  If you have questions about the Windows feedback program, you will need to respond here.
  https://WFP.Microsoft.com/welcome.aspx

  You can send an email to: * e-mail address is removed from the privacy *.

  They would be better able to answer your questions and concerns.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think