Question of access with WLC 2106

Similar Questions

• WLC 2106 routing table do not fill

  Hey guys, I hope you can help with this one.

  I just tried to set up a WLC 2106 and everything seems OK however the routing table is not filled (even directly connected and default route). Currently, I have it plugged into a switch and an AP and they are all two visible in ARP and CDP, but I only ping is peripheral.

  (Cisco Controller) > show the summary

  Number of roads... 0

  Destination Netmask Gateway network

  -------------------    -------------------   -------------------

  (Cisco Controller) > show cdp neighbors detail

  -------------------------

  Device ID:-swt00.asggroup.com.au

  Enter address (s): 10.33.17.62

  Platform: cisco WS-C3750G-48TS, capacity: Switch IGMP router

  Interface: Fastethernet0/0/1, ID of Port (outgoing port): GigabitEthernet1/0/48

  Hold time: 174 s

  Version:

  Cisco IOS software, software C3750 (C3750-IPSERVICESK9-M), Version 12.2 SEE2 (25), RELEASE SOFTWARE (fc1) Copyright (c) 1986-2006 by Cisco Systems, Inc., Compiled Saturday 28 July 06 12:55 by yenanh

  version of the proclamation: 1

  -------------------------

  Device ID: AP1cdf.0f95.732c

  Enter address (s): 10.33.17.10

  Platform: cisco AIR-LAP1142N-N-K9, capacity: Trans-pont

  Interface: Fastethernet0/0/7, ID of Port (outgoing port): GigabitEthernet0

  Hold time: 155 s

  Version:

  Cisco IOS software, C1140 Software (C1140-K9W8-M), Version 12.4 (21 a) JHB1 - VERSION of the SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2010 by Cisco Systems, Inc., Compiled Thursday, Aug 11, 10 at 15:45 by prod_rel_team

  -Other - or ITU (q)

  version of the proclamation: 1

  Configuration of the interface

  Name of the interface... ap-Manager

  MAC address... 58.8 d: 09:93:f1:c0

  IP Address....................................... 10.33.17.2

  IP Netmask....................................... 255.255.255.192

  IP Gateway....................................... 10.33.17.62

  State IP NAT outside... People with disabilities

  External IP NAT... 0.0.0.0

  VLAN............................................. 17

  Port of physics... 1

  Primary DHCP server... 10.33.17.1

  Secondary DHCP server... Not configured

  Option DHCP 82... People with disabilities

  ACL.............................................. Not configured

  AP Manager....................................... Yes

  Comments interface... NO.

  ... Management interface

  MAC address... 58.8 d: 09:93:f1:c0

  IP Address....................................... 10.33.17.1

  IP Netmask....................................... 255.255.255.192

  IP Gateway....................................... 10.33.17.62

  State IP NAT outside... People with disabilities

  External IP NAT... 0.0.0.0

  VLAN............................................. 17

  Quarantine-vlan... 0

  Port of physics... 1

  Primary DHCP server... 10.33.17.1

  Secondary DHCP server... Not configured

  Option DHCP 82... People with disabilities

  ACL.............................................. Not configured

  AP Manager....................................... NO.

  Comments interface... NO.

  Any help would be greatly appreciated
  Mark

  Hello

  Removes the brand management and interface of the AP on the WLC Manager and put the management and the Manager of the Ap in the vlan Switchports native...

  example of...

  the command is...

  WLC > config interface management vlan 0

  WLC > config interface vlan ap-Manager 0

  On the switch...

  switchport mode trunk

  switchport trunk dot1q encap

  switchport trunk vlan native 17

  end

  I assumed the management and Manager of the AP are in vlan 17. make the corresponding changes if not 17.

  Let me know if we can t oping after making the above changes...

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• How to assign a vlan per port cisco all point of access by wlc 702w 5508

  My environment have WLC 5508 and ap 702w 250 units in my site. I need on port port config example all the ap 702w 2 > Vlan 20 port 3 > vlan 30

  Now I canfig one by one.

  Please everyone tell me best way to config a time 250 units.

  Thank you very much...

  Here is the config CLI involved. If you have a list of your AP names you can config CLI of training for all your AP on Notepad & then configure this CLI

  config ap lan port-id  enable config ap lan enable access vlan   

  See this post for more details https://mrncciew.com/2014/09/26/702w-with-wlc-8-0/ HTH Rasika * Pls note all useful responses *.

• External DHCP and WLC 2106

  Hello

  I built a WLC 2106 and 5 LIghweight AP 1121 G-based wireless network. Each AP have multiple ssid in VLANS separated.

  I managed to combine 5 AP to the controller and I have it configured with multiple SSID in different VLANS (each WLAN is associated with the virtual interfaces in the appropriate VLAN).

  The problem is that a wireless client cannot get its IP address from the DHCP externel which is in the same VLAN of the WLAN. And when configured with a static IP address, it works perfectly.

  Can you help please and thank you very much.

  Hi Nizar,

  The controller intercepts all broadcast traffic, so you must configure your DHCP server in your controller to allow your clients to receive DHCP.

  Using the graphical interface, go to the controller-> Interfaces. Click the interface that you use for your SSID. Enter your server DHCP here.

  I would like to know if your problem persists and we can find out what else could be wrong.

• Hi all. IAM using Adobe Document Cloud. After you save a PDF to that cloud, I am able to see my PC files. How to disable this? Is - it my PC files are also available through other PC to access with my Adobe ID? Please help me. Thank you

  Hi all. IAM using Adobe Document Cloud. After you save a PDF to that cloud, I am able to see my PC files as well with a navigation option. How to disable this? My PC files will also be available on other PCs to access with my Adobe ID? Please help me. Thanks in advance.

  Hi indi68632954,

  I can understand your concern & you need to worry about this, as the folders in your PC are not available on other PCs as this option is just to browse through files of the specific system you are working on as shown in the screenshot below.

  

  Only the files that have been uploaded to the cloud of Document will be available over the Internet using Adobe Document Cloud service during authentication of your Adobe ID & password.

  I hope this will answer your query.

  In the case where if you have any other question please let us know, we will be happy to help you.

  Kind regards

  Nicos

• Question about Threads with WHILE and FOR

  Hi all
  
  I have a question on threads with a loop on this topic sentece.
  
  Have the following class:

  class test{
  
  bool foundThing;
  PararellSearch(string [] lista, string s2find){
  while(!foundThing)
  {
  for(int i=0;i<lista.length;i++){
  if(s2find==lista){
  
  foundThing = true;
  
  break;
  
  }
  
  }
  
  }
  
  }
  If I start 10 threads which are using the PararellSearch method to look into lista, each of them inits into a different point, and when some of them found the right word then set foundThing= true. It will stop WHILE and FOR loop in all the threads? 
  If not, how could I do it?
  
  Thanks a lot for your help.
  David.
  
  Edited by: user13553506 on 27-dic-2010 12:15
  
  Edited by: user13553506 on 27-dic-2010 15:54                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    
  			 
  When you post the code, you'll want to post a [url http://sscce.org] NBS so that it is clear that what you try to do it. For example:
  1. in the validation of code, put {code} before and after him, then he will be readable.
  2. the convention in Java must start with a capital letter class names, so test, could not test.
  3. the convention in Java is to start with lowercase letters, so parallelSearch, not PWhateverMisspellingYouHaveThere method names.
  4. There is no such thing as bool. It is a Boolean.
  5. it is a String, not string.
  6. never use == to compare the States of objects (such as the content of the strings). Use equals().
  To answer your question: If you create Test 10 objects, then, given that foundThing is an instance variable, there will be 10 variables entirely independent foundThing. An adjustment will not affect the other. In this case, the easiest thing to do would be to foundThing static, so that there is only one copy which is shared by the Test class as a whole. This isn't the only way, or even the best way in all cases, but you have enough other problems to face, so for now to keep things simple.
  Finally, when you have a variable that is shared by multiple threads, you need to either make all the access to this variable synchronized on the same lock (reads and writes), or you need to declare the volatile variable.
  		   

• ACS RADIUS timeout with WLC 7.0 5.0

  Hi guys,.

  I'm setting up a device Cisco Secure ACS 1120 running 5.0.0.21 ACS to manage the RADIUS of a Cisco WLC 5508 device query running the 7.0.116.0 version.

  • These devices have open communication on all ports - no firewall or ACL
  • they have successful ping communication

  The following statements illustrate some but not all debugging I did to make sure that each device works properly in isolation.

  • Using the simple windows (radserv2.exe) instead of the Cisco ACS RADIUS server
    • This works and the WLC gets answer my fortune Server RADIUS
  • Using a simple windows EAP client to query the ACS using the RADIUS protocol
    • This works and the FAC processes the RADIUS request and sends a response
  • Placed a customer wireshark on the network to inspect the time-out.
    • Wireshark saves the package to the WLC for GBA using port 1812 but does not see responses to GBA package

  At the moment I have the

  1. WLC accepting wireless client association and
  2. sending the query RADIUS (EAP - TLS, PEAP and EAP-FAST) for GBA,
  3. the WLC receives no answer and generates a timeout message and separates the client.
     1. Note this is not a rejection or a similar message, the simple ACS does not even the package. i.e. There is absolutely nothing in the logs of ACS to suggest that he had even received a package of radius of the WLC.

  In summary the WLC and GBA properly operate independently, but they do not communicate via radius.

  Any help appreciated thanks

  It seems that you use ACS 5.0 without tasks.

  For your information, the version of the product is now up to 5.2 and 5.3 ACS should soon be released

  I recall there was a problem with ACS 5.0 with WLC operations that has been resolved in patch for 5.0

  I'm not sure of the specific CDETS but can be:

  CSCsy17858 Any manipulation of Tunnel-Type & Tunnel-Client-Endpoint uploading incorrect

  ACS 5.0 has a rollup with all the patches being accumulated approach

  My recommendation would be to download the patch 8 for ACS 5.0: 5.0.0.21.8

  Patch can be downloaded from CEC

  To install a patch set a repository on ACS (cumulative patches are larger than 32 MB, you can not use TFTP to it), copy the patch file in the repository, click ACS CLI:

  # acs patch installs repository

• Cannot save with WLC 4402 LAP

  Hi all

  I have cisco WLC (AIR-WLC4402-12-K9) with two LAP (AIR-LAP1131AG-A-K9) connected to move and one of the TOUR is able to register with WLC while the other was autonomous AP which has been converted to KNEES who fails to register with WLC. I see that the AP is able to enter the Ip address and even joined the WLC but fails to register. Please help us solve this problem. I have attached all papers relevant to this case. Waiting for your answer.

  FYI I aimed below URL, but could not able to figureout the reason.

  http://www.Cisco.com/en/us/products/ps6366/products_tech_note09186a00808f8599.shtml

  I don't understand.  You have TWO 2 1131AG.  We joined for the last two days and another recently joined.  Say the other keeps "bouncing"?

  Have you checked if the WAP is declining because of the power?

• Question on access to multidimensional data Collection

  Hi all

  I have a multidimensional question on access to data using Collections.

  We use Oracle 11 GR 2.

  Our requirement is as shown below

  We get data from upstream via a stored procedure. The procedure store entry variable is a multidimensional complex type.

  I gave below the structure of the collection

  Step 1

  CREATE or REPLACE TYPE feature_type IS OBJECT

  (

  feature_code VARCHAR2 (10),

  feature_name VARCHAR2 (50).

  feature_value NUMBER

  );

  /

  Step 2

  CREATE or REPLACE TYPE feature_array IS TABLE OF THE feature_type;

  /

  Step 3

  TYPE to CREATE or REPLACE the argument subscriber_type IS OBJECT

  (

  subscriber_id NUMBER,

  first name VARCHAR2 (50).

  name VARCHAR2 (50).

  feature_data feature_array

  );

  /

  Step 4

  CREATE or REPLACE TYPE subscriber_array IS TABLE OF subscriber_type;

  /

  Step 5

  CREATE or REPLACE TYPE order_type IS OBJECT

  (

  order_id NUMBER,

  subscriber_data subscriber_array

  );

  /

  Step 6

  CREATE or REPLACE TYPE order_array IS TABLE OF THE order_type;

  /

  Suppose I have a procedure as shown below

  CREATE OR REPLACE PROCEDURE multidimensional_prc (p_dataarray order_array)

  IS

  lv_order order_array;

  BEGIN

  lv_order: = p_dataarray;

  lv_order: =.

  () order_array

  order_type)

  1,

  () subscriber_array

  subscriber_type argument)

  10,

  "Subscribed 10 first name."

  "Subscriber 10 Lst Name."

  () feature_array

  "feature_type ('F10', ' Featgure Code 10', 10 '))),"

  subscriber_type argument)

  11,

  "Subscriber 11 name."

  "Subscriber 11 Lst Name."

  () feature_array

  "feature_type ('F11', ' Featgure Code 11', 11 '))),"

  order_type)

  2,

  () subscriber_array

  subscriber_type argument)

  20,

  "Subscriber 2 first name."

  "Subscriber 2 Lst Name."

  feature_array (feature_type ("F2", "Featgure Code 2', 20 ')));

  FOR m1 in 1... lv_order. COUNTY

  LOOP

  Dbms_output.put_line (.order_id lv_order (m1));

  -FOR the m2 in 1... lv_order (M1). COUNTING LOOP

  -NULL;

  -END LOOP;

  END LOOP;

  END multidimensional_prc;

  /

  I am able to read the data until the order data as it is in level 1. But when I'm reading the data of the subscriber level 2nd level or level of functionality level (3rd), I make mistakes. Basically, I am unable to read the data into Sub levels.

  Very much appreciate your help here.

  Thank you

  Please ignore this one.

  FOR m1 in 1... lv_order. COUNTY

  LOOP

  Dbms_output.put_line ('- order identification-' | .order_id lv_order (m1));

  FOR m2 in 1... .subscriber_data lv_order (m1). COUNTING LOOP

  Dbms_output.put_line (' Subscriber ID => ' | lv_order (m1) .subscriber_data (m2) .subscriber_id);

  FOR m3 to 1... lv_order (m1) of .subscriber_data .feature_data (m2). COUNTING LOOP

  Dbms_output.put_line (' Code function => ' | lv_order (m1) .subscriber_data (m2) .feature_data (m3) .feature_code);

  Dbms_output.put_line (' include the name => ' | lv_order (m1) .subscriber_data (m2) .feature_data (m3) .feature_name);

  END LOOP;

  END LOOP;

  END LOOP;

  I got the answer.

• I just got the CC but I can't access with me ID. "Assinatura não encontrada" (not found) Haw I can do?

  I just got the CC but I can't access with me ID. "Assinatura não encontrada" (not found) how can I do?

  Contact adobe during the time pst support by clicking here and, when available, click on "still need help," http://helpx.adobe.com/x-productkb/global/service-ccm.html

• Hello, I had paid for the creative but not access, with Juliette deroche sister cloud account, thank you

  Hello, I had paid for the creative but not access, with Juliette deroche sister cloud account, thank you

  A cloud subscription is linked to the Adobe ID of the person who purchased the subscription

  YOU can install and activate on 2 computers, but two activations cannot be used at the same time

  If you give your sister your credential, you can not both use your subscription at the same time

  Cloud license allows 2 activations http://www.adobe.com/legal/licenses-terms.html

  -Install on a 2nd computer http://forums.adobe.com/thread/1452292?tstart=0

  -Windows or Mac has no importance... 2 on the same operating system or 1 on each

  -Two activations may NOT be used at the same time (noted in the link above of the license)

• Access with another computer

  Hello

  In Windows 8, I have VMWare Player 5 installed CentOS with a Rails server.

  Here is the output of the ifconfig command:

  eth1 Link encap HWaddr 00: 0C: 29:60:0F:AF
  INET addr:192.168.118.136 Bcast:192.168.118.255 mask: 255.255.255.0
  ADR inet6: fe80::20c:29ff:fe60: faf / 64 Scope: link
  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1
  Dropped packets: 530695 RX errors: 0:0 overruns: 0 frame: 0
  Dropped packets: 626707 TX errors: 0:0 overruns: 0 carrier: 0
  collisions: 0 txqueuelen:1000
  RX bytes: 202357267 (192,9 MiB) TX bytes: 479045323 (456.8 MiB)
  Basis of interruption: 19 address: 0 x 2024
  Lo encap:Local Loopback link
  INET addr:127.0.0.1 mask: 255.0.0.0
  ADR inet6:: 1/128 Scope: host
  RACE of LOOPING 16436 Metric: 1
  Fall of RX packets: 79511 errors: 0:0 overruns: 0 frame: 0
  Dropped packets: 79511 TX errors: 0:0 overruns: 0 carrier: 0
  collisions: 0 txqueuelen:0
  RX bytes: 11402959 (10.8 MiB) TX bytes: 11402959 (10.8 MiB)

  In Windows 8 (PC), I can access with 192.168.118.136:3000

  But I also would like to access it from another computer on the same network.

  I ran the command line in windows 8 with admin rights to open the virtual network Editor: c:\Program Files (x 86) \VMware\VMware Player > rundll32.exe vmnetui.dll VMNetUI_ShowStandalone

  I saved the following options (see picture):

  

  I can not even access from another computer 192.168.118.136:3000.

  Thanks in advance for your help.

  That's how it should work, unless the traffic/port is blocked by the firewall on the host.

  Basically, you can forward every port you want at the prompt, it doesn't have to be the same port that you used in the comments (e.g. 12345 67890 prompted port host port redirection). Just make sure that you do not use a port that is required by the host of the operating system itself.

  André

• Question/design architecture with best practices?

  Question/design architecture with best practices?
  
  Should I have separate Web server, weblogic application and IAM?
  If yes that how this time will communicate, for example can I webgate on the server that will communicate to each other?
  Any reference to decide how to design and if I have weblogic separate one for enforcement and one for IAM that how session management will take place etc.
  
  How is general design happens IAM project?
  
  Help appreciated.

  I have a business web application deployed on weblogic1 and OHS1

  deploy webtier on this OHS1 to protect the resources on OHS1. webtier will be recorded at OAM (where will be able to communicate with OAM)

  I also IAM deployed on weblogic2 & OHS2

  IAM components have weblogic. then ok. But you don't need to ohs2 here, unless your application itself requires OHS for hosting. But here, you mention that it is fair to IAM - so no need to OSH here. IAM installing requires weblogic.

  wanted to know where should I create provider (weblogic1 or weblogic2), and install webgate (OHS1 or OHS2 or both)?

  I hope it is clear now. If this isn't the case, query post for what is not clear.

• Microsoft Access with Unicode

  Hello

  I recently updated my site in CF5 CF9 running on a virtual server. Here are the specs.

  CF Version: 9,0,0,251028

  Edition: Enterprise

  Operating system: Windows Server 2008

  My old code worked fine except that some queries were turning slowly. My webhost has suggested that I have change the driver to "Microsoft Access" to "Microsoft Access with Unicode." As suggested, it made things much faster. However, there are some pages on my site that didn't work. I did some research and found that I had used the two words 'reserved' for table names that caused pages to fail when you use 'Microsoft Access with Unicode' as the driver. Curiously, the pages worked well with the regular driver of "Microsoft Access".

  I'm now left just a mistake that I can't solve. I get the following error ONLY if you use the "Microsoft Access with Unicode" driver.

  Run database query error.

  Error running query of queries.
  The column reference select [GetList.ItemNo] is not in the table [GetList].

  This is the code that it is.

  <!--use QofQ to join archives interviewed against basket data-->
  < CFQUERY NAME = "GetProducts" DBTYPE = "query" >
  SELECT

  AS ItemNo GetList.ItemNo,
  GetList.Item point, AS
  GetList.Grades AS Grades,
  Price GetList.Price AS,
  Amount of GetList.OrderQty AS,
  (GetList.OrderQty * GetList.Price) AS ProductSubTotal
  OF GetList
  < / CFQUERY >

  Is there a problem with "Microsoft Access with Unicode" play not with query of queries?

  I would be very happy any contribution to this issue.

  Thank you

  Steve

  ... two words 'reserved' for table names that caused pages to fail when you use 'Microsoft Access with Unicode' as the driver. Curiously, the pages worked well with the regular driver of "Microsoft Access".

  Different database drivers can have different reserved words.

  Run database query error.

  Error running query of queries.
  The column reference select [GetList.ItemNo] is not in the table [GetList].

  This is the code that it is.

  It seems very unlikely that the error has something to do with the driver used in the original request.  That means the original query 'GetList' look like? It contains the "ItemNo" column OR have this column more than once?

• new here... question to start with

  Hello world...

  New to the forum and glad to hear things with Dreamweaver.

  A question to start with... How does a program Dreamweaver so that it automatically reformatted in different browsers (sizes).  Is it still possible?

  Cheers...

  Twingi

  How does a program Dreamweaver so that it automatically reformatted in different browsers (sizes).  Is it still possible?

  It is certainly possible.  Tell us what you mean by 'formatting automatically' and we will tell you how to do it.