Question re: parameters of the Optimal high-speed (slow Internet) wireless adapter

Similar Questions

• "The internet connection speed" Vs "the speed of a wireless adapter.

  Hello

  I'm subscribered of a DSL with a speed of 512 Kbps (kilobits per second).

  However, when I tested the speed of my internet connection with a variety of Web sites, the speed of a wireless router test while wirelessely connected to a wireless router, I have not found any speed of 512 Kbps.
  What I found is shown on screenshots below to test the speed of connection to internet Web sites.

  

  

  

  As a result, my question are:

  First: What would be my answer if I asked about the speed of your internet connection is? Is there a difference between the speed of a LILY and the speed of an internet connection?

  Finally: In the screenshot below, the speed of the wireless adapter, I think. If so, what advantage is there this speed?

  

  Traditional math units go up (or down) in thousands so yes 1000 K = 1 M. computers have slight variation because in some cases, it is 1024 but the difference is not significant.

  The A in ADSL is asynchronous for the upload and download are not equal. As that data consumer is not serious to you, everything you send upwards is requests for web pages where are small compared to the downloaded pages.

  European providers stuck to the same speed of upload years even if the download rate has increased.

  One of the problems we have is that there are people like you stuck at 1 / 2 Mb/s using systems designed for multi-Mb of Microsoft networks.

• I need to know the Freq of my HP Pavilion wireless adapter is 2.4 or 5 ghz?

  The specifications for the HPE 440f does not say, it lists only the 1 GB under network but mine as also wireless adapter card and says nothing wireless.

  The number of prod is: BM 427AA #ABA.

  It runs at 2.4 or 5 ghz?  OR is it the PC Wireless not cela and decides to only commicates the router and the router?

  Anyone know?

  Hello

  Not too bad at all, a large number of machines still use 2.4 GHz. In my house, all printers (HP, Canon, Epson) use of 2.4 GHz. Any computer that uses b/g/n uses 2.4 GHz and my observations, ILS ALL FUNCTION properly. The card will probably remain for the life of the machine.

  Kind regards.

• Unable to connect wireless Xbox 360 controller to the Xbox 360 to a PC wireless adapter

  IM installation driver for adapter, restart computer, insert the USB adapter, try connecting the Xbox 360 wireless adapter controller - nothing happens, adapter cannot see controller. After half an hour trying to CONECT setting on the adapter. Next day, same thing: an hour and connected controller. But that's all. Third time a cant connect even after the hour by train. Help, please! How do I operate it normally?

  P.S. I have Windows XP Service Pack 3

  Thanks in advance.

  Hello

  Have you tried the article Umesh gave in the previous post?

  If this does not help, then we will perform a clean boot of the operating system and see if that helps.

  The following describes this process:

  http://support.Microsoft.com/kb/310353

  http://support.Microsoft.com/kb/316434

  Best regards

  Matthew_Ha

• IE9 would freeze to the top and then my internet wireless receiver disconnects. Why is he doing this and how to fix it?

  I would be online and then it would freeze shortly after disconnects my internet wireless receiver and I don't have to connect again. But I don't think it's the wireless receiver since it is new.

  Hello

  1. have you made changes on the computer before this problem?

  2. What is the brand and model of the computer?

  3. do the Internet disconnected only when you use Internet Explorer or does it happen with all

  4. have you contacted your ISP on this issue?

  Method 1: You can temporarily disable the security software and check...

  Turn off the Antivirus software
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software
  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: If this does not help, start the computer in safe mode with networking Mode and check.
  Start your computer in safe mode
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  If the Internet works fine in Safe Mode with network, then I suggest you to perform a clean boot and check if any third-party application is causing this problem.

  Put the computer to boot and check if you can play the game:
  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, place k the computer to boot to the normal startup.

  Method 3: If the problem only occurs when you use Internet Explorer, I suggest to optimize Internet Explorer and check.

  How to optimize Internet Explorer
  http://support.Microsoft.com/kb/936213/no
  WARNING: Reset Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.

   

• Questions of parameters for the added control - project version

  Hello

  My fellow designer and FINALLY got version control/robosource 3.1 put in place on our Robohelp project. What a difference! Now, I have a few questions about the settings. We all have two connection to the Robohelp file shared on a server database. We would now have our a copy of the project on our local machines or not we keep a case on a shared server/player? I ask because our version control is originally Robohelp at startup and perform updates very, very slowly (20 minutes to start).

  I also, parameters marked to allow a user to check out a file at the same time (we are unwilling do a lot of fusion, as there's only two of us working on over 1,000 topics). When I try and import or create a new file, I get an error that the "* / root.fpj ' is in use and cannot have multiple extractions. What can I do about it?

  Thanks for your help!

  Hi, Mollyid

  Rick and Amebr have made some excellent points. It happens that I've worked on a few demos of Adobe Captivate, illustrating the basic techniques for the getting started with RoboSource Control.

  Each is approximately two to three minutes long.

  It shows how a new project is added to RoboSource Control for the first time:

  http://www.showmethedemo.com/tutorials/RSC-Add1stTime/

  This one shows how Open a project that is already at the source control in your working on your local hard drive folder.

  http://www.showmethedemo.com/tutorials/RSC-OpenProj1stTime/

  I will be tweaking these demos in the coming days, but I think that they lay down the basic ideas.

  Suggestions for improvement are welcome as I refine these demos.

  John

  John Daigle
  Adobe Certified RoboHelp and Captivate instructor
  Evergreen, Colorado
  http://www.showmethedemo.com

• Internet high speed slows down significantly when wifi turned on on my Mac.

  When I run a speed test I get 29Mbps with my mac wifi disabled.

  When I turn on wifi it drops to 5 Mbps.

  Any suggestions please?

  Hold down the ALT or option key by clicking the Airport icon in the menu bar, what rate of transmission does show?

  also...

  System Preferences > network, click on the little train at the bottom next to the + & - icons (unlock all first if it is locked), choose the value of Service order.

  The interface that connects to the Internet should be moved to the top of the list.

• [Win7] How routing metric is determined when wired and connected to the same subnet and enabled both wireless adapter

  We have one under the Network Setup:

  1 Win 7 laptop with the wireless and wired adatper1 card1 enabled and connected to the 192.168.1.0 network.

  WLA1 - 192.168.1.2

  WA1 - 192.168.1.3

  2 Win 7 laptop with the wireless and wired adatper2 card2 enabled and connected to the 192.168.1.0 network.

  WLA2 - 192.168.1.4

  WA2 - 192.168.1.5

  WLA1 and WLA2 are connected by a wireless access point.

  WA1 and WA2 are connected via L2 switch.

  Every time we ping from laptop1 to 192.168.1.4, need the wireless path.

  Similarly, when we ping from laptop1 to 192.168.1.5 only need to access wired road.

  In addition, if we disable WLA1 in laptop1 and laptop1 192.168.1.4 ping, ping does not occur and ping is successful only if the wireless network adapter is enabled. It does not take the cable path.

  I just sub questions:

  -On what basis the route is chosen correctly?

  -Can we expect this happens all the time or roads can vary according to certain parameters?

  -Why it only takes the path wired when we ping from laptop1 to 192.168.1.4 after having turned off the WLA1.

  RB

  You will get a more definitive answer on metrics on Technet

  This issue is beyond the scope of this site and must be placed on Technet or MSDN
  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Start Vista start up blocking guard down, the whole system is slow, internet keeps crashing and error blue screen occurs, System Restore does not

  Signature of the problem:

  Problem event name: BlueScreen

  The system version: 6.0.6002.2.2.0.768.3

  Locale ID: 2057

  More information about the problem:

  BCCode:                                              77

  BCP1:                                                   C00000B5

  BCP2:                                                   C00000B5

  BCP3:                                                   00000000

  BCP4:                                                   0AC90000

  OS version: 6_0_6002

  Service Pack: 2_0

  Product:                                              768_1

  Files helping to describe the problem:

  C:\Windows\Minidump\Mini061510-01.dmp

  C:\Users\Sony\AppData\Local\Temp\WER-89201-0.SysData.XML

  C:\Users\Sony\AppData\Local\Temp\WERF93C.tmp.version.txt

  You said the details of the error checking 0x77 - KERNEL_STACK_INPAGE_ERROR.  "This bug check indicates that the data page of the kernel of the required paging file cannot be read in memory."  The reason for the inability to read the data were "STATUS_IO_TIMEOUT' -"{Device Timeout} the specified on HS IO operation did not complete before the expiry time."

  Most likely, this could be due to a problem with the hardware, as a problem with your drive.  These details, combined with your description of the problem, further suggests that this may be the case. Check your event logs (Event Viewer in the in Control Panel Administrative Tools folder) to the messages relevant or notable.   You can also check the cables involving HD are nice and warm.

  As your hard disk may be involved, you want to ensure you had a backup of your data before doing large thing (a backup good and verified, is never a bad idea, anyway).

  Check the behavior in safe mode and the boot, as described below (follow the links):

  To treat blue screens, following general tips:

  Consider running chkdsk on all partitions.  Leave complete chkdsk on each partition and see if that helps.

  Also consider running SFC/scannow.

  If you start in safe mode, do you still feel bugs? What if you do a clean boot, or boot device?

  Consider the memory with memtest86 or Windows Memory Diagnostic test. Note that memory that pass the tests isn't necessarily good memory - he not only failed a review.  Examine systematically to eliminate the system RAM - run with a few modules for awhile and see how things are going. Then try the other modules.

  Other common suggestions include ensuring drivers are up to date (including video drivers), but also to ensure that you use the latest version of the BIOS.

  It may be useful to use the driver verifier.  To activate the... Driver Verifier start-> verifier.exe-> OK-> create standard settings - > then-> the names of the drivers select in a list-> next-> sort by provider-> select all non-Microsoft drivers-> finish and OK your way out of the dialog box.

  Then restart and use the system as you normally and wait for a problem.  In case the system does not completely start after activation of the Verifier, boot mode safe and run driver verifier and tell him to remove the changes.

  Wait for an error checking to happen after you have enabled the auditor as described and then transfer it to your SkyDriveand provide a link.

• Causing the Blue Screen of Death (IRQL_NOT_LESS_OR_EQUAL) wireless adapter

  I had a Linksys WUSB600N Wireless-N USB adapter (dual band ver. 2) for a period of several months now, no problem, running on Windows 7 Pro 32-bit.  So without any hardware or software changes (to my knowledge), have the adapter plugged during initialize causes my computer blue screen.  Unplug, Windows starts fine, but it will crash again in the same way once I plug the unit and it research networks.

  I went to the Linksys site and downloaded the Windows 7 driver for the card (they have even one for as long as I was using Vista all this time), and that seems to help for a little bit.  For some reason any my computer not collapsed yet until I wait long enough after the departure to the top before plugging.  But it's about all or nothing.

  It's the essence of the blue screen message (had to find somewhere else and copy it so not sure the numeric codes below):

  A problem has been detected and windows has shut down to prevent damage to your computer.

  IRQL_NOT_LESS_OR_EQUAL

  If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps:

  Check that a new hardware or software is installed correctly. If it is a new installation, ask your hardware manufacturer or software, the windows updates, you might need.

  If problems continue, disable or remove any newly installed hardware or software. Disable the BIOS memory options such as implementing caching or shading. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and then select Safe Mode.

  Technical information:
  STOP: 0X0000000A (0X00000002, 0X00000000, 0XCDCDCDC9, 0X804DBE7B)

  The date of the beginning of the physical memory dump
  Total physical memory dump.
  For more assistance, contact your system administrator or technical support group.

  I tried to start in safe mode, but it won't work without networking, so I wasn't able to learn something useful about the problem.  I don't have that much experience with technical problems, although I spent a good amount of time working on driver problems.  No help no matter who might be able to give me would be greatly appreciated.

  Some info on my PC:

  Gateway GT5628 (ACPI x 86 PC-based)

  Intel (r) Core (TM) 2 CPU Quad Q6600 @ 2.40 GHz 2.39 GHz

  NVIDIA GeForce 8800 GTS 512 MB

  KB977165 has created various problems on some systems and was temporarily removed from Windows Update.

  I would say to uninstall KB977165 to see if that solves the problem.

• Internet connection for the second computer on a connection high speed

  I have two computers, one running XP and a Vista.

  They were bound by a simple home network wired using a switch. Internet is available via dial-up on the Vista machine.

  I changed the cable (high speed), always on the Vista machine only and leaving the intact cable network.

  Next step was to install a Linksys WRT54G2 V1 router and run the connection Strip through it.

  Then, I took the switch network cables and connected to the router. I am able to access the files on each machine to other machine.

  However, I do not have access to the Internet on the XP machine and do not know what I should do at this point.

  Could someone lead me to some documents that might guide me please?

  Thank you very much...

  You cycle the modem power cable after unplugging the XP machine, connected to the router?

  The best thing to do is power down (cable modem, router and PC), then turn on the cable modem, wait it a few minutes, then turn on the router, wait a few minutes, then turn on the PC.

• High speed USB 2.0 physical location of the port

  I have a HP Pavilion dv6-3122us Notebook PC. I get messages when the transfer of files on the fastest "high speed USB 2.0 port.  My user manual tells me that I have three ports, of which one is a 2.0 port but I am unable to say which is the 2.0 port. Can anyone help me find information on the location and identification of the usb ports?

  James Worthen Sr

  I just got offline with a HP tech rep and he told me that the high-speed 2.0 port was, in fact, the eSATA/USB port.

  With this port, it gives me four ports and I wouldn't imagine that it was even a USB port, as it seems slightly different rather than the usual USB ports. I pluged my Bluetooth adapter in this port and it works fine. I have not tried to transfer files with this port again, except the photos with the bluetooth, but when I do I will seek to see if I still get the same message while transferring. I doubt I would. I believe that this issue has been resolved and I will mark it as my. Thanks to all who responded.

• Internet high speed & 1stgen AirportExpress

  Recently I upgraded my internet speed to 150Mbps. using my (model A1264) 1stGen Airport Express, I am only able to get 50Mbps to my office. My iMac is at short range with my router. My internet is slow speed b/c my Express is outdated? A new Express will allow me received the speeds I have upgraded to or is a desperate need? On the 2nd floor, there is an another desktop or home that connects to the internet regularly (teenage son online games).

  The 1 st Gen AirPort Express and 2nd Gen AirPort Express have only 100 Mbit/s Ethernet ports, so in theory, it would be the top speed that the Express could never offer.

  To the extent where wireless is concerned, 50 - 60 Mbps would be what to expect from an AirPort Express which is provided a 100 Mbps connection, since he has never been known for its performance wireless... primarily because of a small simple antennas buried in the product.

  A new AirPort Extreme has 1 000 Mbps Ethernet ports and the much higher speed wireless capability... (six wireless antennas all located towards the top at the top of the "tower")... which would be the product to try if you want to stay with a router from Apple.  At Apple, and you buy a 14 day no questions asked return guarantees, so if the product does not wait, it may be returned for credit or refund.

• USB port high speed - not available on Tecra M1

  Hi all
  I joined my new external HARD drive to my Tecra M1 and XP says I use * not *; port USB high speed.
  Question: How can I switch to high speed USB port?

  Driver: Intel 82801DB/DBM USB 2.0 Hostcontroller - 24 D of Microsoft Version 6.1.2600.0 issued 1.6.2002

  Thanks for the reply in advance.

  See you soon,.
  Tom

  First of all, you can't 'upgrade' your internal USB port to a Highspeed USB port. This is NOT possible, but your machine must have at least 2! ports USB 2.0 capable.

  I suggest you do the following: download the latest drivers for your machine on Toshiba Driver download site, install and check if the error message appears, anywhere you´re attaching your USB 2.0 device.

  Usually one or 2 of these ports should be able to USB 2.0.

  If still, you get the same error message then come back and give some comments, then we can discuss more about.

  See you soon

• high-speed FPGA multipliers

  When should you use these multipliers rather times ordinary? Is it disadvantages if these using ie do take several doors to implement?

  What additions to broadband?

  Thank you

  You might find this link from the help information: use of Math functions high speed

  In particular: "National Instruments recommends to use the LabVIEW digital unless you need the benefits that offer the features high-speed mathematical."  I don't know if there is a sentence any for use when not not required.  For additions and multiplies, the main advantage for high-speed operations, is that you can more easily control the pipelining when executing a series of mathematical operations. (EDIT: but if you don't need math pipeline, there is no advantage.)