R40 to r50e harddrive swap, will not identify wireless or video

Similar Questions

• Satellite A135-S2356 - BIOS will not identify SATA hard

  Hello everyone, hope you can help out me.

  Got a Satellite A135-2356 opportunity, everything seems fine but BIOS will not identify SATA HDD, shows no disk BIOS downgraded to 1.30, not good, upgraded to 1.40, not good. BIOS has no change/test/detection of HDD/SATA settings options. Tested the drive in another laptop and it reads very well. Received the Toshiba (Vista Basic 32) recovery CD, but given that the BIOS will not read the disk, can't do anything. Cleaned contacts, not good. This HARD disk must be too large, or something for the Board of Directors.

  * Hitachi HTS541612J9SA00 120 GB SATA, 5400 RPM *.

  Thanks for the help!

  Hello Richie

  To be honest, I do not think the disc is too big for your laptop. I can imagine that your laptop can handle with drives of 160 GB too. Unfortunately there is no public document on the possibilities of HARD drive upgrade. I can imagine that ASP in your country has information about such things.

  It's also quite strange that HDD is not recognized correctly. Long ago, I had the same problem. Every time when I used F12 at startup disk HARD were not as boot device. Solution in my case was to upgrade the BIOS to the default settings. I believe that your BIOS has already the default settings, but try to do it again.

• HP Photosmart Prem 310a went offline suddenly and will not identify the SSID to run the Network Setup Wizard.

  All of a sudden the printer has gone offline a few days ago.  Went through all the diagnostics, etc. but nothing fixed.  A solution-Assistant will not work cause it will not identify the SSID of the network that he has done since it was installed (long ago).  Have tried everything I can find online, unless I don't understand or is not quite apply and still nothing.  Wireless network works with everything except the printer. I am not very computer so I do not understand most of the letter & numbers abbreviations used here.  Help.

  It may be a heat problem - radio from the printer gets flakey when it's hot.

  Finding 5 wireless networks should - Yes you have one, but your neighbors also have.

• Computer will not print wireless or network

  original title: my computer is anti-social

  It will not print wireless or network with other computers in the House.  any advice?

  Hello

  1. what version of Windows is installed on the computer?

  2. were you able to print earlier?

  3. are you able to print via a wired connection?

  4. What is the brand and model of your printer?

  5. are you aware of any changes made to the computer, before the show?

  Method 1:

  Temporarily disable your antivirus software, and then print.

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Note: Runs the computer without antivirus software or firewall is a potential threat to the computer; don't forget to activate the security software after completing the troubleshooting steps and after you have identified the problem.

  Method 2:

  Check out the following link.

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  I hope this helps.

• Firefox 3.6.3 will not play integrated youtube videos. It comes up with ' year error occurred please try again later. " It happens all the time

  Firefox 3.6.3 will not play integrated youtube videos. It comes up with ' year error occurred please try again later. " It happens all the time. If you click to go to youtube the clip plays.

  This has happened

  Each time Firefox opened

  Well, here's my answer to my own post.

  After reading some posts here about possible solutions, I tried to delete all the cookies for YouTube (Tools > options > privacy > show cookies > youtube.com). Then tested on a site with integrated video would not play before and on YouTube directly - both worked!

  The poster with the suggestion of cookies also proposed changes to the 'exceptions', but it was not necessary at least for me.

• My i-phone 5 will not take photos or videos

  My i-phone 5 will not take photos or videos

  Start here: get help with the camera on your iPhone, iPad or iPod touch - Apple Support

• V525W printer will not connect wireless

  I just moved and had to change my ISP.  Now, my V525W printer which was working fine, will not connect wireless.

  When I try to reinstall the printer, the program stops after I connect the USB "put in place by cable".  The CONTINUE button dark rest.

  I tried every suggstion I find on the Board for more than three hours and still not get this piece of junk to work.

  I have an all-in-one Dell XPS running Windows 7 machine.

  Can someone please?

  Rick,

  After a few "cooling off" days, I decided to TANOE this problem again and it seems that I finally work!

  I went in the menu on the printer and restore the default settings.  I always had the same problem with the Installation of the Dell program I went into the Windows 7 Control Panel and clicked on "Add a wireless device to the network."  He immediately recognized the printer and I followed the steps until the light green enabled WiFi fixed.   Then, I went through the installation of Dell again and was able to print, scan, etc.

  Thanks again,

  Tom

• Cannot complete installation of Live TV. Media Center will not identify Directv remote. Is there a solution?

  I have a Dell PC with Vista Home Premium.  Until recently, when the operating system had to be reloaded, I watched decoder of live TV on Media Center for the past two years, using a Directv.  I have tried to re install the TV, but cannot complete the process, as my Directv remotes are not recognized.  The signal is fine (as of the previous steps shows the appropriate image and the signal, but the installation process cannot be performed due to the problem of distance not recognized. (The remote functions of the Directv box very well). How can I find use of the tv, Setup finish signal?

  Hello

  You won't get HDTV without a Digital Cable Ready tuner and a cable card. How about you
  will have need a HDCP compatible graphics card and a TV/monitor taking support this
  as well.
  The kit Hauppage offers is substantially the same as I told you.

  clear QAM availability varies according to the cable company. most begin to encrypt
  everything.

  > The same can be done through Windows Media Center, by clicking the video image by clicking on Zoom. But in MCE when you have a cable box, you will also need an approved Microsoft IR blaster to control the cable box. If you n? not have this part, you will get the IR hardware not found error. The HVR - 950 Q does not come with this, but if you really want to use Media Center, you can buy a kit from our online store here http://store.hauppauge.com/hardware2.asp?product=mce_remote remote"

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-pictures/Media-Center-cant-detect-dvrset-top-box-but-finds/43a9685d-d093-4cfa-88ac-17132a1e5b53

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-pictures/cannot-complete-Windows-Media-Center-Setup-IR/6db1ada7-3380-44a2-A369-268e5cd7c013

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-pictures/cannot-complete-Windows-Media-Center-Setup-IR/6db1ada7-3380-44a2-A369-268e5cd7c013

  http://Windows.Microsoft.com/VI-VN/Windows-Vista/troubleshoot-problems-with-watching-TV-on-your-computer

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-pictures/Media-Center-will-not-set-up-TV-because-Windows/5c038734-7bb6-48D4-AAC9-f4dee9a3d442

• XPS 8300 will not identify data reader 5 to

  I have a desktop computer XPS 8300, Windows 7/64, 12 GB of RAM. Boot drive is a 500 GB SSD, and there is a SATA 2 TB of data. I'm a photographer, so I need a lot of data storage.

  I just bought a Toshiba MD04ACA500 5 to to use as a data drive (NO boot).

  My XPS 8300 can see the drive, but insists on the fact that it contains only 500 GB of storage, not 5 TB. I did the following:

  • Run Diskpart from a DOS window.
  • Run Diskmgmt.msc;
  • Run the tool to partition a third party
  • Also, I went through Windows KB 2581408 procedure of adding a player of great size.

  No matter what I do, the drive is detected as only 500 GB.

  The XPS 8300 is possible to work with a 5 TB drive? If so, how?

  Thank you, Ed

  Disks over 2 TB software needed to work with disks of large capacity and NEED 64 Bit Windows.  INTEL RST integrated in win7 is 8.x, which means that he WILL NOT see large capacity disks. Seagate manage it with the driver and utilities.

  • 2 t of learning beyond
  • Interactive Guide for disks more larger-Than - 2 TB

  http://www.Seagate.com/support/downloads/beyond-2TB/

  INTEL RST 10.1 at least is NECESSARY for advanced format drives.

  With windows vista or 7 install ATA mode then the microsoft patch is necessary before moving on to the AHCI.

  https://support.Microsoft.com/en-us/KB/922976

  Once passed to Ahci and work, you install the version of the RST that works for your model.

  Latest and most recent versions of the decline of the RST support more older chipsets.

  The latest 15 13 or 14 or 11 or 12 may not work.

  Before 9.x, it was called MSM (Matrix Storage Manager)

  It changed of MSM to RST in the 9.x versions.

  10.1 or greater is required for the GPT partitions greater than 2 TB.

  9.6 or higher is required for larger than 120 Gig aka advanced format drives.

  V9.6 driver Intel Rapid Storage Technology (RST) and above.

  http://www.Intel.com/support/chipsets/IMSM/sb/CS-031502.htm
  http://www.Intel.com/p/en_US/support/highlights/chpsts/IMSM

  9.6.0.1014

  https://Downloadcenter.Intel.com/download/15251

  10.1.0.1008 is the version of transition.

  https://Downloadcenter.Intel.com/download/20104

  10.6.0.1022

  https://Downloadcenter.Intel.com/download/20707

  11.0.0.1032

  https://Downloadcenter.Intel.com/download/20868

• Windows 7 pro will not identify disk hard esata

  I use dock cables unlimited Office. USB port works fine.

  I tried the steps above on a DELL Latitude E6510 laptop with Windows 7 and it will not consistantly recognize the drive eSATA external hard.

  Once the laptop has continued to view the contents of an external hard drive, even after having been unplugged.

  Thank you

  Chris

• LR 4 will not identify the 2nd hard disk in the source during import?

  I run 2 hard drives in my PC. A disc is only for programs. And the largest are for photos/music. When I go to import the source the left pane will not recognize the drive B:, C: drive only and he will recognize even my M: drive with is my outside. Im not sure what to do at this point to add the B: drive to the source. Thank you

  It is sometimes useful if you put a "fictitious" picture on a disk via Win Explorer. So, try this first and see if your player appears.

  If this does not help:

  Letter B is not a good choice for a player on a PC. It's because of the ol-old time when drive letters A and B were reserved for the disc x6.25 "(A) and the floppy disk drive (B).

  That's why the first drive in PC today is always named c. (letter)

  And, I don't know maybe that Lr does not recognize the drive letters A and B. So rename your drive B to the D drive.

  Do this in the Windows Control Panel > system and security > administrative tools > computer Nortsk > disk management. In the lower window where it shows your drives, highlight the drive in question and then go > Action > all tasks > change drive letter and path.

  For more information, open in your control panel and in the search box, type .

• my laptop will not connect wireless

  my new hp laptop windows 8 will not connect to my wireless internet. It will be after I restart, but after a few minutes, it goes with limited access. How can I fix?

  Hello erobb14,

  We will try to remove your Wi - Fi card and let Windows to install it again. This will reset any options or configuration errors that may have been applied.

  Press and hold the Windows key and press W.
  In the search bar, type "Device Manager" (without the quotes) and press ENTER.

  Once inside the Device Manager, please find and unfold the group named "network adapters".
  From there, to identify your wireless card (it will very probably include the word "wireless" or "802.11".

  Now, right click on the wireless network device and click "Uninstall".
  If you're facing a check box asking if you want to remove the driver as well, please let it be empty.

  After the device has been uninstalled, restart your device and try to connect to the wireless again.

  I would like to know how that works for you.

• Satellite L500-207 will not find wireless networks

  My laptop cannot identify wireless networks at all and I don't know how to fix it. Everything works fine and I'm aware wireless is turned on and anti-virus scans were clean.

  First of all, the problem occurred after I have reset default DNS for the DNS to google so I wonder if this is what caused the problem.

  I would be very happy any assistance that could be given in the resolution of this problem.

  > My laptop cannot identify wireless networks at all and I don't know how to fix it.

  Does that mean exactly? You can see your WLan or you see another WLan in the neighborhood?
  If you can't see any WLan then this means that the card wireless network is not correctly enabled in this case use FN + F8 to activate the WLan.

  In addition, check the settings of TCP/IP to the wireless network.
  In Protocol TCP/IP properties, you can find the settings as all these parameters must be set to automatically assign the IP address.

• Lenovo thinkpad t450s will not be to the video when it's on battery

  Video freezes when the notebook is on battery, when you move the mouse, it continues to play. Audio plays all the time. Overall performance slows down terribly. Windows will not close or open until the passage of the mouse. Videos won't play on 3 browsers and if plays hard drive

  The laptop is less than a month, all the updates are installed, anti virus deleted. When it is plugged in, I have none of the problems listed.

• Want 5540: Blue light blinks and the printer will not connect wireless

  Printer has been successfully implemented and operational, but today the blue light flashes, it does not connect to our wireless and will not be the same impression with ubs. I disconnected and reconnected several times and removed and reloaded the software, but the problem persists.

  Turn off the router and the printer. Turn on the router, wait 3 min. Turn on the printer and see if it connects to the router.