XPS 8300 will not identify data reader 5 to

Similar Questions

• Satellite A135-S2356 - BIOS will not identify SATA hard

  Hello everyone, hope you can help out me.

  Got a Satellite A135-2356 opportunity, everything seems fine but BIOS will not identify SATA HDD, shows no disk BIOS downgraded to 1.30, not good, upgraded to 1.40, not good. BIOS has no change/test/detection of HDD/SATA settings options. Tested the drive in another laptop and it reads very well. Received the Toshiba (Vista Basic 32) recovery CD, but given that the BIOS will not read the disk, can't do anything. Cleaned contacts, not good. This HARD disk must be too large, or something for the Board of Directors.

  * Hitachi HTS541612J9SA00 120 GB SATA, 5400 RPM *.

  Thanks for the help!

  Hello Richie

  To be honest, I do not think the disc is too big for your laptop. I can imagine that your laptop can handle with drives of 160 GB too. Unfortunately there is no public document on the possibilities of HARD drive upgrade. I can imagine that ASP in your country has information about such things.

  It's also quite strange that HDD is not recognized correctly. Long ago, I had the same problem. Every time when I used F12 at startup disk HARD were not as boot device. Solution in my case was to upgrade the BIOS to the default settings. I believe that your BIOS has already the default settings, but try to do it again.

• HP Photosmart Prem 310a went offline suddenly and will not identify the SSID to run the Network Setup Wizard.

  All of a sudden the printer has gone offline a few days ago.  Went through all the diagnostics, etc. but nothing fixed.  A solution-Assistant will not work cause it will not identify the SSID of the network that he has done since it was installed (long ago).  Have tried everything I can find online, unless I don't understand or is not quite apply and still nothing.  Wireless network works with everything except the printer. I am not very computer so I do not understand most of the letter & numbers abbreviations used here.  Help.

  It may be a heat problem - radio from the printer gets flakey when it's hot.

  Finding 5 wireless networks should - Yes you have one, but your neighbors also have.

• XPS 8700 will not feed radeon hd 7790

  I bought this computer a month ago and I tried to upgrade the gpu, but it will not produce a video signal. I was able to use the radeon, even in an old pc (Dell Studio since 2009 under win vista) with the same power supply that I use in the XPS (Corsair 500W) specification. I installed both in the XPS specification, but the radeon does not illuminate. I connected the cable 3 x 2 but no luck. I went to the geforce gt 635 which has been installed in the factory and works well for all the components work. I think that the power supply should be more than enough, but I don't see other reasons, it will not work. I tried to install the drivers (and uninstall geforce) before putting the card in as well. I had to use the Corsair PSU because the original 460W did not have a record of 3 x 2. It's the video card:

  http://pcpartpicker.com/part/Asus-video-card-hd7790dc2oc1gd5

  Data sheet:
  64-bit Windows 8

  4770 i7 CPU @ 3.40 GHz

  8 GB OF DDR3 MEMORY

  Google search for Windows 8 disable secure boot

  Let me know if this helps.

• CD and DVD player will not open or read

  My USB does not open. I got the message no program associated with the file.

  I reformated the by the advice of Verbatum USB flash drive.  Now the Flash Player works fine, BUT no optical drive will not work.  I can insert a disc into the CD or DVD drive, and it won't play.

  I can click on one of the icons for the drives in my computer and they do not open or play.

  I need help to solve this problem.

  I have Windows XP Home Edition and running IE 8 with all the updates of Windows and IE.

  Help please.

  You can try AutoPlay Repair Wizard from Microsoft here:

  http://www.Microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=c680a7b6-e8fa-45C4-A171-1b389cfacdad

  Download the tool... click Next and select cd/dvd drive and try to open it and such.  Then click on begin Test, and you might find an answer to your problem.

  ///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

  I suggest this one below

  Even better...

  http://support.Microsoft.com/GP/cd_dvd_drive_problems is Microsoft Fix it... It will run a diagnostic tool on your 'question' click on this link and it will take you just

  What it fixes...
  • Your CD or DVD drive does not read or write and is shown as disabled
  • The media in your CD or DVD drive cannot be read
  • The media cannot be written for your CD or DVD drive
  • You receive one of the following errors:
    • A specific class or a specific device driver is missing or damaged
    • A CD or DVD drive is not found or is not connected
    • The CD or DVD drive is faced with a problem which does not work properly
    • The CD or DVD drive is not accessible via a drive letter assigned
  How it works...
  Microsoft Automated Troubleshooting Services scans your computer and detects that the root causes of common problems, then

  

  Automatically solves the problems that it encounters, and

  Offers additional resources if the problem is not resolved

• Dell XPS 600 will not PUBLISH the same!

  I have a dell xps 600 with the 14f0w91 of service and code whenever I turn on the PC, all fans are on MAXIMUM speed with power clear amber and 3.4 lights are on. It will not even POST.

  Is there any fix for this free?

  Thank you, Nick Hanson

  http://support.Dell.com/

  If you have no instructions POST/Splash/Bios-setting the screen to the power, you seem to have a hardware problem.

  If under warranty, contact Dell.

  If it is not under warranty, contact a local and trusted computer repair workshop.

  See you soon.

  Mick Murphy - Microsoft partner

• Dell XPS 12 - will not start / turns on after hard reset

  Last night I was with my XPS w12 in laptop mode on battery and he finally went down to 7% of the capacity.  At this point, it turns off the display and I moved my office to connect the power adapter (thinking it would simply turn the display when there was enough power...  The screen never came back (I waited 15-20 minutes), but the battery has been recharged.  At that time, I tried a hard reset by holding the power button for 5 to 10 seconds.

  When I tried to turn it on, nothing happened.  No backlit keyboard, no screen, just the fan.  The light never came the switch either. So I tried an another hard reset with the same results.  I even tried to turn it on with the "D" button held down for on board diagnostics and got nothing more than the start of the fan.

  I thought it might be an overheating problem, so I let it set for an hour and tried again - none other than the fan. It seems that the laptop does not pass the initial diagnosis and not even up to the point where the bios starts to load.

  I really thought that my cell phone was dead and ready for use.  I took it in the office the next day so I could call Dell Support Pro. Just for fun, I plugged with the AC adapter and tried to turn it on - viola!  It started working again.

  I had this problem once before, and he began to work after 2-3 resets hard. I was working on a proposal when the laptop went down. I tried reset hard over a period of 4 hours with no result. It baffles me why it start OK the next day morning.

  I was wondering if anyone else has had the same problem.  I am running the A07 BIOS (the most common) and my 12 XPS is configured with 8 GB of memory and 256 GB SSD with an i7 and Intel wireless card.

  Any suggestions on this diagnosis? The hardest part is then if fails, the failure is total - you are unable to diagnosis. When she comes back, all right, and there is than any event in the event log that relate to the failure.

  OK - I narrowed down it to the following:

  When the laptop is "asleep", it will finally in power mode. It seems that connect a power adapter for the laptop at this point will enter a State of confusion, when the button is pressed, the laptop fan turns on but no light on the power button or on the keyboard – the screen remains blank.  Laptop fan works (it is very quiet - he must hold the phone to your ear to hear it).

  I don't know if the cause is a low battery or if the issue is simply with the State of the CPU to power down.  All I know is that when it happens, if I disconnect the power adapter and press and hold the power button until the fan of the laptop turns off, the hard reset allows him to come back normally.  If you leave the adapter attached, it will charge the battery but will not allow the laptop start.

  I said this experiment several times with the same result every time. I'm guessing that there is a bug in the BIOS that defines an error state that are resolved with the associated power Board. Do the hard reset without the adapter seems reliable to fix the problem.

• Windows Media Player 12 will not open or read CD/DVD

  Excuse me, I know that I posted earlier but I accidentally hit the wrong button and it says has answered my question and it was not. I had a virus on my computer and it was cleaned professionally. Now my windows media player will not open. He also will not play a cd/dvd or existing music files on my computer. The icon appears on the screen, but nothing happens when I try to open it. I can't do a system restore because there is nothing to restore, my computer was completely wiped out. Someone suggested this below "Disable media features" reboot and then turn on again. I tried already with no luck. I'm also totally updated everything I could find to put on my computer up-to-date.

  1. click on Start (lower-left) and then on Control Panel.

  2. click on programs and features.

  3. on the left side of the screen, click on 'Windows turn features on or off".

  4. look for the entry called multimedia features and extend it by using the symbol. +.

  5. uncheck the box for Windows Media Player.

  6. click on OK.

  7 restart the PC.

  8. click on Start (lower-left) and then on Control Panel.

  9. click on programs and features.

  10. on the left side of the screen, click on 'Windows turn features on or off".

  11 look for the entry called multimedia features and to extend it using the symbol +.

  12. check the box for Windows Media Player.

  13. click on OK.

  14. restart the PC.

  I was afraid of that - "Configuration parameters can be set wrongly."

  On google, there are a few reports of this error message and I couldn't find any that it is resolved. I hope that someone else will be "the chip" with a solution. I'm sorry.

  There are some media player FixIt who might want to try (I have not had your specific problem and Ive not run the FixIt so can't say for sure).

  You can try things like a SFC/scannow , that can help, but I doubt it. I guess it depends on what the virus.

  You could check that the virus is actually went in downloading, installing, free update (update in the Admin) and running a scan with Malwarebytes , but if it was 'cleaned professionally"should be deleted. But unfortunately things that his attack can still be altered.

  You could try a test, to create a new user account 'test' and the connection through that to see if WMP works from this account. for example, it can be your user profile that has been damaged. If this account works WMP then migrate your data everywhere...

  If all goes well, a WMP expert will come to the rescue.

• My dv5 Pavilion will not transfer data wireless.

  I have a Pavilion dv5 with Windows 7 and an Atheros AF5009. A few days ago it stopped transfer of wireless Internet data suddensly. Here are the gory details-

  • The computer connects to the wireless router
  • Other devices connect to the router
  • The connection is presented as "strong".
  • Corresponding IP addresses between the router and the computer
  • I have reset TCP/IP with no luck
  • I disconnected and then reconnected the adapter
  • I restarted the router
  • I reconnected manually to ensure that the security passwords and settings are OK
  • I've disabled the firewall, virus protection, etc. (they are now back, of course) no luck here.
  • Ethernet connection works fine
  • Web sites will not download
  • When I run a ping test between the router and the computer test fails, even if the computer shows as "active".
  • I'm totally stumped!

  My best guess is that the wireless adapter has a problem, or the parameters or otherwise.

  Anyone have any ideas?

  Thank you!

  Roger

  Hi, Roger:

  It seems to me that you done everything but run the system restore utility and update the driver.

  First try the system restore utility, and then select a restore to a date point, you know that your INTERNET access is working.

  If this resolves the problem, then update the driver for your wireless card.

  This is the latest driver for your card:

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=3688868&swItem=ob-99392-1&mode=5

  If none of the above works, I tend to believe that the card has been to kind of hardware failure.

  Paul

• I'm having a problem with Dreamweaver, interaction with servers of Cox... Will download... In the download process, however it will not transfer data

  A week ago I started having this problem.  Dreamweaver while interacting with Cox... servers that perform very well... will allow me to download on MAC computer but will not download files without altering the data.

  When I try to reproduce this problem on a PC without any problems...

  I found the issue... for some reason any... I had to adjust my MTU settings to 1450 and 1475... and the problem was solved...

• Satellite A215-S7414 will not recovery disc read

  I need to restore my laptop to factory setting, but whenever I start the wizard of toshiba recory it stops and displays and error: 03-EEEE-0000.
  I know he can play discs b/c last time I put the 2nd drive instead of the 1st and the computer says to put 1 disc.
  When I made the same mistake that presented themselves. I tried to boot from the cd/dvd but it stil does not work. :(

  Hello

  Have you tried to boot from another bootable CD? I mean can start you Microsoft Windows CD or DVD in Vista?

  The error looks like the CD/DVD drive is not able to read and to start from the first recovery CD Toshiba.
  Maybe the disc is not more readable for this drive.

• Cannot complete installation of Live TV. Media Center will not identify Directv remote. Is there a solution?

  I have a Dell PC with Vista Home Premium.  Until recently, when the operating system had to be reloaded, I watched decoder of live TV on Media Center for the past two years, using a Directv.  I have tried to re install the TV, but cannot complete the process, as my Directv remotes are not recognized.  The signal is fine (as of the previous steps shows the appropriate image and the signal, but the installation process cannot be performed due to the problem of distance not recognized. (The remote functions of the Directv box very well). How can I find use of the tv, Setup finish signal?

  Hello

  You won't get HDTV without a Digital Cable Ready tuner and a cable card. How about you
  will have need a HDCP compatible graphics card and a TV/monitor taking support this
  as well.
  The kit Hauppage offers is substantially the same as I told you.

  clear QAM availability varies according to the cable company. most begin to encrypt
  everything.

  > The same can be done through Windows Media Center, by clicking the video image by clicking on Zoom. But in MCE when you have a cable box, you will also need an approved Microsoft IR blaster to control the cable box. If you n? not have this part, you will get the IR hardware not found error. The HVR - 950 Q does not come with this, but if you really want to use Media Center, you can buy a kit from our online store here http://store.hauppauge.com/hardware2.asp?product=mce_remote remote"

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-pictures/Media-Center-cant-detect-dvrset-top-box-but-finds/43a9685d-d093-4cfa-88ac-17132a1e5b53

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-pictures/cannot-complete-Windows-Media-Center-Setup-IR/6db1ada7-3380-44a2-A369-268e5cd7c013

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-pictures/cannot-complete-Windows-Media-Center-Setup-IR/6db1ada7-3380-44a2-A369-268e5cd7c013

  http://Windows.Microsoft.com/VI-VN/Windows-Vista/troubleshoot-problems-with-watching-TV-on-your-computer

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-pictures/Media-Center-will-not-set-up-TV-because-Windows/5c038734-7bb6-48D4-AAC9-f4dee9a3d442

• Links will not open or read online .wmv files

  IE8 will not play video files WMV links

  With IE8, under Windows7 RC, in a Web page there is a link such as: http://.../file.wmv
  If I click on it, an error page appears immediately, saying: Internet explorer cannot display this webpage.
  A more detailed description of the error is on 'lost internet connectivity' or 'error in the link' etc...
  But if I just right click on the LINKet "save under", the wmv downloads file be saved and opens and play flawlessly in default WMP.
  The system has just WMP as a player, configured with the default settings, I rechecked.
  I have the same problem on another machine with IE8 on Vista with Divx and VLC Player (but all by default WMP) installed

  I found reports of similar problems on the internet, but really no identification of true and the solution of this problem (just the usual platoon 'use firefox!' or 'download winamp!' comments..)

  Any help here?
  Thank you!

  Difficulty: block notebook open in these lines:
  Windows Registry Editor Version 5.00
  [HKEY_CLASSES_ROOT\.avi]
  @= "WMP11. AssocFile.AVI ".
  [HKEY_CLASSES_ROOT\.asf]
  @= "WMP11. AssocFile.ASF ".
  [HKEY_CLASSES_ROOT\.wmv]
  @= "WMP11. AssocFile.WMV ".
  Save the file to your desktop 'Filename'.reg - make sure that you change the record in a file .txt for a '. ' open the file, right adjust the register, open your movies

• Windows 7 pro will not identify disk hard esata

  I use dock cables unlimited Office. USB port works fine.

  I tried the steps above on a DELL Latitude E6510 laptop with Windows 7 and it will not consistantly recognize the drive eSATA external hard.

  Once the laptop has continued to view the contents of an external hard drive, even after having been unplugged.

  Thank you

  Chris

• LR 4 will not identify the 2nd hard disk in the source during import?

  I run 2 hard drives in my PC. A disc is only for programs. And the largest are for photos/music. When I go to import the source the left pane will not recognize the drive B:, C: drive only and he will recognize even my M: drive with is my outside. Im not sure what to do at this point to add the B: drive to the source. Thank you

  It is sometimes useful if you put a "fictitious" picture on a disk via Win Explorer. So, try this first and see if your player appears.

  If this does not help:

  Letter B is not a good choice for a player on a PC. It's because of the ol-old time when drive letters A and B were reserved for the disc x6.25 "(A) and the floppy disk drive (B).

  That's why the first drive in PC today is always named c. (letter)

  And, I don't know maybe that Lr does not recognize the drive letters A and B. So rename your drive B to the D drive.

  Do this in the Windows Control Panel > system and security > administrative tools > computer Nortsk > disk management. In the lower window where it shows your drives, highlight the drive in question and then go > Action > all tasks > change drive letter and path.

  For more information, open in your control panel and in the search box, type .