RAID 5 problem with R410 Perc 6 / i controller

Similar Questions

• HP 255 g4: problem with USB and SM Bus controller

  I have a problem with the (USB) Universal Serial Bus controller and SM Bus controller.
  System identifies them.

  
  I installed all the drivers for my noutbook of this site, but it does not work...
  Please, help me!

  I believe that these devices are based on the AMD chipset driver package... USB 3.0 and SMBus Controller:

  http://support.AMD.com/en-us/download/chipset?OS=Windows%2010%20-%2064

  Top package. @Paul_Tikkanen will know for sure.

• Problem with PCI device and network controller

  Hi, I have problems with drivers, I tried several but does not work. I have a laptop HP 2000 with windows 7 Ultimate 64-bit. These are the properties of hardware retail:

  Network controller

  PCI\VEN_10EC & DEV_8176 & SUBSYS_1629103C & REV_01
  PCI\VEN_10EC & DEV_8176 & SUBSYS_1629103C
  PCI\VEN_10EC & DEV_8176 & CC_028000
  PCI\VEN_10EC & DEV_8176 & CC_0280

  PCI device

  PCI\VEN_10EC & DEV_5209 & SUBSYS_520910EC & REV_01
  PCI\VEN_10EC & DEV_5209 & SUBSYS_520910EC
  PCI\VEN_10EC & DEV_5209 & CC_FF0000
  PCI\VEN_10EC & DEV_5209 & CC_FF00

  Help, please

  Thank you

  Hello:

  You need these drivers:

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5060882&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_105197_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-102008-1&cc=us&DLC=en&LC=en&OS=4063&product=5093394&sw_lang=

• Problem with laptop Lenovo T400 video controller

  Hello

  I have problems with the video controller on my laptop of Lenovo T400.

  Brand new and installed with Windows XP factory.

  He maintains and prompt to install the drivers for the video controller.

  I tried to use the CD and downloaded the chipset and video drivers Lenovo Web site, but the problem persists.

  Anyone encountered before?

  Thank you and best regards

  Solo

  option 3.

  Discreet GPU = ATI GPU
  Integrated GPU = Intel GPU
  Switchable graphics = Intel or ATI switchable by Vista and Win 7 OS Thinkvantage Power Manager.

• UCS C22 M3 software RAID LSI problem with hard drive

  Hello

  I post here because I searched many hours for a stupid problem.

  I have a Cisco UCS C22 M3 with soft RAID LSI MagicRAID.
  I have two hard disk of 1 TB.
  I create a RAID array with the type 1 (mirror).

  When I run the installation of VMware ESXi 5.1 U1 I see the RAID array, but the two discs.
  I think that it is a driver problem.
  So, I install special with an iso VMware in the VMware Web site for Cisco server.
  I have test with ESXi 5.0 and 5.1, and 5.1 U1 but it's the same problem.

  I try to remove the RAID array and to install esx on disc one monkey. Installation works well, but in the boot menu, I can't boot from a hard disk. I don't know why I search with UEFI and she is disabled.

  I test with windows 2012, and 2008R2 to check if its working but in install I don't see also hard drive or the RAID array.
  I go to Cisco and download the driver of the 2G for VMware Linux and Windows.
  I try inserting the driver in windows install, but does not.
  I think that the driver for a hardware RAID card and software.

  I have try to disable the LSI RAID in the advanced bios "SouthBridge". After I disabled I don't know how I can do to start on the hard drive.
  When I go to the start menu (F6) I see absolutely nothing in drive.

  I test this on two Cisco server.

  I can't know what I can do now. I take a working installation tomorrow and nothing.

  I join you a photo of the boot sequence LSI.

  Thank you very much.

  Sent by Cisco Support technique iPhone App

  Stephane,

  For what I understand, you use the RAID controller integrated, therefore, these drivers will not work you:

  -LSI 92xx

  -LSI 106xE

  -LSI 2008 M

  -INS 3081E-R

  -LSI8708EM2

  -LSI 9201< all="" of="" the="" above="" are="" not="" the="" controller="" you="">

  -CISO 1225 x< this="" is="" for="" the="" vic="">

  -CISCO P81E< this="" is="" for="" the="" 1st="" generation="" of="" vic="" cards,="" so="" definitely="" not="" a="" raid="">

  Pilots are organized into top level by operating system folders, and each folder of OS has a structured series hierarchically who become more specific subfolders so that you can find the exact drivers you need. When you navigate to a folder containing the drivers, it will contain also one or several README files that explains what are these drivers in particular.

  Here is an example of the structure of folder for Windows:

  Windows    ChipSet       vendor          blade-model-number             OS-version-number                All                ia64                Lang (contains language subfolders)                Vista                x64

  You need to look for: /< OS > / storage/Intel/C600 /.< if="" you="" are ="" doing="" the="" installation="" of="" the="" os="" through="" the="" kvm,="" you="" first="" need="" to="" un-mount="" the="" os="" .iso="" image="" to="" mount="" the="" drivers,="" once="" the="" drivers="" are="" done,="" un-mount="" the="" drivers="" and="" mount="" again="" the="" os="" .iso="">

  If it does not, you better open a TAC case that will allow us to put in place an additional troubleshooting Webex meeting.

  -Kenny

• HP 630-problem with Ethernet, PCI device, PCI controller drivers controller just communications

  I am faced with my laptop HP 630 driver wireless network problems.

  Can you please help me to solve the problems.

  OS: Windows 7 Ultimate, 64-bit

  The hardware ID is as follows.

  Ethernet controller

  PCI\VEN_10EC & DEV_8168 & SUBSYS_3672103C & REV_06
  PCI\VEN_10EC & DEV_8168 & SUBSYS_3672103C
  PCI\VEN_10EC & DEV_8168 & CC_020000
  PCI\VEN_10EC & DEV_8168 & CC_0200

  PCI device

  PCI\VEN_10EC & DEV_5209 & SUBSYS_3672103C & REV_01
  PCI\VEN_10EC & DEV_5209 & SUBSYS_3672103C
  PCI\VEN_10EC & DEV_5209 & CC_FF0000
  PCI\VEN_10EC & DEV_5209 & CC_FF00

  PCI simple communication controller

  PCI\VEN_8086 & DEV_1C3A & SUBSYS_3672103C & REV_04
  PCI\VEN_8086 & DEV_1C3A & SUBSYS_3672103C
  PCI\VEN_8086 & DEV_1C3A & CC_078000
  PCI\VEN_8086 & DEV_1C3A & CC_0780

  Please go back...

  Hi, aarie:

  Please see my response to your other post on the link below:

  http://h30434.www3.HP.com/T5/wireless-Internet-home/HP-630-WiresLess-not-working/m-p/1747559#M32446

  Paul

• Problem with satellite Pro L300 Ethernet controller

  Hello

  I have a Satellite Pro L300 (PSLB9A - 02L 001). Have'nt after being on the dial for the year last I was wireless (it worked well before that) but am now back on broadband but I don't seem to have any wireless.
  Checked the Device Manager and there is a yellow exclamation next to the ethernet controller and it seems there is no pilot, but apart from that, there is no further details. I tried to update the driver but it cannot find the driver on my computer and it will not search the Internet for this.

  I tried, but none of the drivers I downloaded seems to work...
  At the back of the computer laptop is a sticker - PA3613U-1MPC, I think it's the wifi card that is missing the driver but I can't find a driver for it for the life of me...

  Any help would be wonderful.
  Daryl in New Zealand

  You are right. This part number is WLAN Card. I put t know what operating system you use but for download driver Atheros http://aps2.toshiba-tro.de/wlan/?page=downloads WLAN

  I hope this will help.

  What is now with LAN driver? Do you need it too?
  In any case, visit the Toshiba support page under http://www.mytoshiba.com.au/support/download and there you should find good LAN driver for your model of laptop.

  Send comments.

• Problem with to demote a domain controller

  Hi all

  I tried today demote a domain controller, but my domain environment is still need of this domain controller to work.
  I have windows Server 2003 Small Business DC as DC1 & lately I added windows Server 2008 R2 DC as DC2 in the new box as an additional area. Now, I need to downgrade the windows server 2003 SB (DC1) in an old box.
  I transferred FSMO (all 5 roles) and remove DC1 from the announcement. In addition, remove it AD users & computers and Services of & Sites AD and DNS... I used the steps in this link: http://www.petri.co.il/delete_failed_dcs_from_ad.htm
  When Dc1 is not connected to the network, you receive this error (see this picture of this link http://i41.tinypic.com/30upoxj.png) every time I opened all the consoles AD (AD users & computers, etc...).
  Also, when I tried to change the domain controller, it seems that he could not located the domain or domain controllers. Please, see this photo from this link: http://i43.tinypic.com/2n6afx1.png
  I can solve it reconnect DC1 to the network, but I don't want to keep it longer, and I don't know what Miss me? Also, I tried to use dcpromo to remove the domain controller DC1, but I got an error message that tells me that this is not the last domain controller in the forest and cannot proceed with the removal of the DC.
  Can you help me as soon as POSSIBLE, I'm right here.
  Waiting for your answer... Thank you!

  Hi Haitham2011,

  The question you have posted is related to Windows Server 2008 and would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://TechNet.Microsoft.com/en-us/WindowsServer/default

  I hope this helps.

• 3 physical disks in 1 TB in RAID 5 with only its 1 TB usable space incorrectly? Using a Dell PERC 6 / i controller.

  We have a server Dell PowerEdge with a PERC 6 / i controller. There are three physical disks for 1 TB. I created a RAID 5 array, but it seems that there is only 1 TB of usable space after you initialize the virtual disk RAID 5.

  What is wrong? I Googled what should be the size, and I think we should not 1 TB, 2 TB of usable space?

  Too bad. It looks like the physical disks are 500 GB in size, which makes sense.

• PE R410 / PERC 6 / I VDs invisible to OS install

  Its weeks like that, why I hate going on vacation.

  I have a Dell R410 server, latest version of the BIOS (1.12.0) w / PERC 6 / I adapter RAID-5 (package 6.3.3.0002 w / 1.22.52 firmware).

  This server has been configured w / two VDs: a VD/OS "boot" of 256 GB and a score of 'data' of 5 TB. Existing running Windows 2008 Standard, can't remember how long, probably because it was purchased? 4? Years ago.

  While I was on vacation, 'something' happened. 'Something' being defined as I don't know what. It is a server non-mission-critical - I use it mainly as a software and data for IT to support repository, so nobody really noticed in offline mode. When I returned (and necessary to access info about it) I noticed it was to start, basically sitting in the place where he finished POST with the slider at the bottom of the screen immediately after the display BMC configuration (no card iDRAC in this area). Last message on the screen is "4 fan speed may change depending on configuration card installation and the system option", which is quite normal (at least since I bought the box).

  So, I guess the box rebooted at some point, done all the POST diagnostics and then couldn't not would not start.

  Rebooted the box is gone in the RAID configuration section, the two VDs are Optimal. When I boot, in messages, POST, PERC messages indicate "2 virtual drives, the host adapter" and "2 virtual drives managed by the BIOS. So far so good. Exit RAID config, let the system restart and pass all messages post once again and finally, after the message 'Fan 4', the box a few stalls.

  I think that something that happened for the boot sector or partition from the OS so I was missing. I thought it would be a good time to just format the OS partition and install Windows Server 2012R2 x 64 instead, which brings the box to date.

  Only one problem... 2012R2 does not "see" the VDs.

  From my readings online, 2012R2 has allegedly supported integrated Perc 6 / I controller. Then, when I start installation of 2012R2, I expect the system to detect the VDs. But it's not.

  Based on a different view, I found here, I deleted and recreated my VD "OS". Still no luck.

  Perhaps believing the Perc 6 / I I didn't somehow supported by the native 2012R2 Installer, I scrounged up until I found a driver that acknowledged the Installer (side: why is it so difficult to find the drivers on the dell site now?) All I could find are these "packets update" which really must be on the machine in the operating system already installed, and you cannot extract the drivers on another system to put on a USB key. Very aggravating, unless I'm missing something obvious.). I think that the driver I eventually ended up finding was W2003x64 Perc 6 / I pilot.

  Setup recognizes the driver on the USB, when I select it I assume it installs (I see the key USB activity), but the installer still does not see the two VDs.

  Given that the box had the original Windows Server 2008 is installed, I dug my old records 2008 installation and tried with them. No go. Exactly the same problem. Makes me wonder how I ever got this box 2008 running. Maybe I imagined it.

  So, after this lengthy rant, my question: what I am doing wrong, or should I do something here I think... because, frankly, I'm out of ideas. At this point, that I would be happy just getting ANY OS installed on the box so I can copy the information off of it to another machine, because, while information on it is not vital, yet its going to be a major PITA to rebuild.

  Anyone has an idea why 2008 and 2012 is not recognize the PERC 6 / I VDs? Is there a different driver, I need, or...?

  Thank you

  Excellent forensic work, Mike!

  Sorry to hear about your problems with your PERC 6 / i adapter

  Is your replacement PERC 6 / I, at the same level as your original adapter firmware (6.3.3 - 0002, 1.22.52 - 1909)? Link to PERC 6 / I Firmware

  Since your VDs appear as optimal, and you receive no error messages during POST about your storage controller / VDs, we can ignore this:
  PERC BIOS (CTRL-R in the POST) VD Mgmt screen main Menu:
  1. press CTRL-n to access of PD Mgmt screen
  2. check the information from hard drive (number of drives listed, drive status).

  Please try to check the consistency of the data:

  Perform the following steps to run a consistency check (it is not destructive).
  1 inside PERC BIOS (CTRL-R in the POST), press to access the VD Mgmt menu
  screen.
  2. tap on the down arrow key to select the virtual disk #.
  3. press on to display the menu of available actions.
  4. press the down arrow key to select consistency check.
  5. press the right arrow key to display the menu of available actions, Start and Stop button.
  6. Select start and press to run a consistency check.
  The consistency check runs and checks the redundancy data in the virtual disks.
  7. After you start the consistency check, press to display the previous menu.

  For your initial problems with undetected drives, ensure that bootable media is enabled:
  1. from PERC BIOS, press to access the Ctrl Mgmt menu screen.
  2. press on to move the cursor to enable THE controller BIOS in the settings area.
  3. press the SPACEBAR to select Enable controller BIOS. An X appears next to enable THE controller BIOS.
  4. Press apply on to move the cursor on the button and then press to apply the selection.

  Try to check your Windows partition using diskpart (there is a 'RECOVER' option that you can consider).

  Carlos

  #Iwork4Dell

• Problems with the network controller

  Hi, I have a problem with the driver for network controller. I mean my wireless does not work... it connects to the router, but it still has this yellow warning and will not connect to internet. I tried everything and it doesn't work. I have not found a pilot wireless on the hp site. I have a HP laptop model 15-r020sq.

  Hi, I used the driver that you post. Now I have the same problems as before. I went over the details of the driver it's what he know upstairs: PCI\VEN_1814 & DEV_3290 & SUBSYS_18EC103C & REV_00

• Dell R730xd with mode PERC H730 and RAID/HBA

  Hi all

  I have a new Dell R730xd with a PERC H730 card. I have six 4TB readers connected to it. It works very well in RAID mode, but the map also has support for the 'HBA' mode In other words, the card works like a basic HBA and disables the RAID functionality. When the HBA mode map software can see the disks, but they never make it through the operating system. Readers are not detected in the MESSAGE as no RAID and there is no option to convert them to no RAID.

  I talked about this through with technical support, which have been really helpful, but we can't find a solution. It seems to work on their server, but not mine.

  So I write here to see if anyone else uses this configuration, or to find out if anyone has had the same problem and maybe even resolved. Let me know!

  Thank you
  Tim.

  We had the same problem as well. I was able to solve the problem but doing a factory reset in the HBA. After the reset and reboot retype again HBA configuration and activate the HBA mode and your good.

• Problem with XServe and XServe RAID via Fibre Channel

  Hello everyone,

  I have a problem with my blended Xserve RAID.

  I see in RAID-Admin and configure it successfully (via Ethernet). Connect with our Xserve via Fibre Channel, but the XServe and XServe RAID do not detect each other.

  The fiber on the Xserve channel LEDs are white on the Xserve RAID completely off and permanent.

  RAID-Admin status of Fibre Channel: 'No connection (1 table)' with a red square.

  If I try to open the utility of fiber channel I get the message: "card Fibre Channel is not found." Utility disk OS X can't, too.

  I changed the card connector cable, and made several reboots. But each time the same thing: they do not detect each other.

  Xserve (2009):

  -2.26 GHz Quad-Core Intel Xeon 5500

  -Map of Apple dual-channel 4 Gb Fibre Channel (LSI7204EP)

  XServe RAID:

  -RAID 5 in an array (only on the left with 5 x 500 GB)

  -1.5.1 Firmware

  -Cable Apple 4 Gb SFP - SFP

  Thanks for your help and sorry for my bad English!

  Hi Mpm-Mainz,

  Check if you have enabled LUN masking. To be able to see, you will need to download raid admin 1.5 not the 1.5.1

  Xserve RAID Admin Tools 1.5

  Have you also tried to use the other controller? Even if there is no disc in there, then it should appear in the preferences of fiber card system.

  Thank you
  Owen

• HP proliant ML 310 problem with raid

  Hello

  I have a problem with replacement hard 160 GB of drive for raid 1.

  RAID consists of 2 160 GB drives. Local dealer told me that some configurations must take place in the BIOS and set the new drive. could you please send me some if available doc

  the product name is HP proliant ML 310

  Part number is 398413-501

  Thank you

  Hello:

  I suggest that also post your question in the section Server Proliant HP Business Support Forum.

  http://h30499.www3.HP.com/T5/ProLiant-servers-ml-DL-SL/BD-p/ITRC-264

  Paul

• Problems with Adaptec RAID followed after update02 arcconf

  Hello NG,.

  We have problems with a 5.1 ESXi host.

  It worked fine with 5.1_update01.

  After that we did a upgrade to Adaptec arrconf tool 5.1_update02 gives us an error message saying:

  Inspectors found: 0

  Invalid controller number.

  We suspect that the driver Adaptec SCSI (vmware-esxi-drivers-scsi-aacraid-510.5.2.1.29900.-1.1.5.799733.x86_64.vib) has been replaced by the hotfix.

  Any who have had a similar problem?

  What can we do? How to find the old driver?

  Kind regards...

  Hello

  to install VIB/driver to take effect, you must restart you host. If something goes wrong don't worry, you can use alt-bootbank to restore any changes made by the installer.

  To use successfully restore to the previous picture SHIFT + R during the process of start-up of ESXi.

  _________________________________________________________________________________________

  If you have found this device or any other answer useful, please consider to award points. (use the Correct or useful)

  Kind regards

  P.