Randomly call in Cisco TelePresence SX80.

Similar Questions

• The Cisco Telepresence SX80 solution help

  Hello

  I really want to get your help in this scenario.

  We have 2 branches and planning to set (for the first site 3 SX80 of three meeting rooms) and (one SX80 for another branch).

  We have all communications between sites works well and phones are connected using CUCM 10.5 my question how connect us these 2 branches to collect and SX80 features on site with a minimum of equipment?

  Can make us the video call normally trunk Sip or H323 or do we have to express way / telepresence Server?

  Please notify.

  Thank you

  Hello

  Could you say how the branches are connected to each other? It is through the Internet or VPN? Then we will know how to position the highways.

  If you have CUCM you will use as your calling command for your SX80s and write them down on it as SIP endpoints.

  SX80 endpoint can be ordered with multisite option so it can appeal a multisite up to 5 participants. You will need Telepresence server to host concurrent conferences with more than 5 participants in a conference. You also need a conductor when implementing telepresence servers to manage the resources of the Conference.

  Kind regards

  Acevirgil

• Requirements of Cisco TelePresence C for landlines and mobile calls

  Hello everyone,

  I have questions about Cisco TelePresence C: I know that you can call to landline and mobile phones as well as these.

  I would like to know more technical details about this:

  -What else should be part of the installation of the TP C series in the case of calls on fixed or mobile? This Protocol must be used (H320 ISDN)?

  Should I also buy Cisco TelePresence ISDN Link - http://www.cisco.com/c/en/us/products/collaboration-endpoints/telepresen... or can I use a gateway and SIP protocol for fixed lines?

  Thank you for the answers.

  Inorder for you make or receive calls to PSTN/Mobile then you will need some sort of bridge. Yes the ISDN link can work if you have a few points of termination.

  If you have more endpoints and activate this cabability for all then a network infrastructure device would be best, such as the Cisco TelePresence ISDN GW 3241

• Driver of Cisco Telepresence - room LoopBack

  Hello world

  Is it possible to create a meeting room on Cisco Telepresence driver that will return the video to the appellant alone in the room? As the [email protected] / * / Cisco's Sip URI? (A kind of selfview room)

  Thanks for your help.

  It is possible to show only one participant connected to a MCU conference selfview, but not for telepresence Server conferences.  It comes without caring if the driver is involved or not.  The service provided by Cisco closure is obtained with the C40/60 endpoints where the audio and the video plays in a loop directly to the connected call (output HDMI to HDMI-in, output audio RCA audio-in RCA/RCA).

• Configuration of the firewall Cisco Telepresence MCU 5320

  Hi all.

  I searched all the documents of the MCU again, but I found nothing on the ports it uses.

  Help me

  HI Sandra.  The 5320 MCU is the same as 4500 MCU.

  Incoming ports

  • FTP - TCP:21 + transient (dynamic rather than fixed) used TCP ports for passive mode
  • HTTP - TCP:80
  • HTTPS - TCP:443
  • H.323 - TCP:1720 + ephemeral TCP ports for incoming calls
  • SNMP - UDP:161
  • Outgoing calls to H.323 involve ephemeral ports TCP connections TCP TCP:1720 and a certain number of ephemeral TCP ports
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5060
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5061
  • Outgoing interruptions SNMP are sent the ephemeral ports UDP Port 162
  • Media (including audio and video, FECC messages) are ephemeral ports from ephemeral ports UDP.
  • The products acquired Cisco TANDBERG/Codian and gateway series series Cisco TelePresence allocate the ephemeral ports between 49152 to 65535 *. It is possible to change the ports on which these products receive and establish connections. For example, by default the Codian products Cisco acquired listen port 1720 H.323 calls and connections to port 80 web browser, but these can be modified (go to network > Services).

  Keep in mind this MCU does not support the streaming or conference me and have either the GK aboard.  If these ports are listed.

  The link to the Article can be found here:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/articles/conferencing_products_conferenceme_ports_used_kb_3.shtml

  VR

  Patrick

• Cisco TelePresence SX20 + VCS 8.2 Server and Skype for business 2015

  Nice day! My name is Dimitri! Have Cisco TelePresence SX20 + VCS 8.2 Server and Skype for business 2015. Is it possible to set up a conference call SFB and appeal to all subscribers of this conference? At present, we can only call on a single client and SFB. We have the current version of the software TCNC5.1.4.295090 SX20 - is it possible he obnoviti 7, and it will help to improve the situation? Thank you!

  I'm no expert on this technology, but I have some idea and already deployed some projects dealing with the integration of Cisco (CUCM, VCS) video infrastructure to Microsoft video infra like Lync. It would be the same process to make it work in your case.

  How does your deployed SFB? How do you do a conference for audio and video, participants can join the conference by dialing?

  • Mediation server would be required as a front-end server for you to integrate IP/PBXS using SIP trunk to enable voice (audio) Conference with the participants to the PSTN.
  • AVMCU Should be (Audio video Multipoint Conferencing Unit) will host the video conference that will include video endpoints as participants.
  • Video of Interop (SCREW) Server would be required to interface your SFB to third video conference infrastructure such as Cisco UCM or VCS for the endpoints Cisco call client SFB of endpoint of Cisco to participate to the conference organised on SFB by dialing the conference number.

  I'd say contact your AM SFB or Support as well for queries about how to plan your infrastructure SFB and direction.

  Kind regards

  Acevirgil

• I want to install a Cisco TelePresence TX9000

  I want to install a Cisco TelePresence TX9000 and I wonder if I have to register and update the 03 CTS for the same version of software and it allows them to registered in the call manager?

  Hello

  Do you you have 4 codecs on the TX9000: TS1 and TS2, TS3 TS4 (presentation).  All codecs must have the same software. Codec central TS1 must be registered at the CUCM.

  I hope that this answer than you might expect.

  Kind regards

  Ahmed

• Is any impact of a change of the password of the local user account on an instance of a content server Cisco TelePresence virtual computer?

  Hello

  I'm looking to see if there is an impact to change the password of the local user account on an instance of a content server Cisco TelePresence virtual machine?

  The software version is v6.2 build 4073.

  Thank you in advance,

  Robert

  I'll assume, you are referring to the administrator account, but it can be applied to any local account which is located on the TCS server itself.  It has no impact to change the password, unless you are using doesn't say account to connect to the server of TCS or web interface, it will not affect the application of TCS as most things such as external storage or clustering rely on domain accounts and not the local server.

• Cisco TelePresence Manager version 1.7 does support Windows Small Business Server 2008?

  Hello

  Is Microsoft Windows Small Business Server 2008 supported the Protocol LDAP, AD and MS Exchange server for Cisco TelePresence Manager version 1.7?

  Thank you

  AA

  Hello Ahmed - although this configuration "can work", Windows 2008 Small Business Server is not on the support list. This means that it has not been tested and it certifies to work with telepresence.

  To my knowledge, he's not on the roadmap for the future support however, I search and repost as soon as I have an answer for you.

  Kind regards

  -Andrew

  Sent by Cisco Support technique iPhone App

• Cisco TelePresence SX20 with laptop

  I use a Cisco TelePresence as autonomous SX20 endpoint configured with a public IP address (in Pakistan). I want to connect a portable computer (to Canada) to start video conferencing using the portable camera. Please advice me the software to install on the laptop so that I can start with my SX20 videoconferencing based on IP configured on my SX20.

  To understand kindly refer to the disposal of partner network.

  Please help me its urgent.

  Hello

  www.ciscojabbervideo.com

  BR Oleksandr

• Cisco telepresence sx20

  Dear support team,

  I want to know how to configure cisco telepresence sx20.

  any body can help pls...

  Configuration Cisco Telepresence Sx20 is not easy to do. I think below link will help you for configuration.

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/endpoint/quick-set-SX20/TC5/administrator_guide/sx20_quickset_administrator_guide_tc51.PDF

• Cisco Telepresence SX20 and Touch 8 Configuration after paired

  Hello

  I successfully connected and combined the SX20 Cisco's Telepresence and Cisco Telepresence Touch 8. Before using the 8 key, we used the remote control instead. As a result, I have two questions about this.

  1. as far as I know, when I use the 8 key, the remote control cannot be used. Is it possible to use both of them?

  2. How can I change the background of my SX20 touch 8? Previously, the remote I can easily choose the background for my SX20. But after pairing with Touch 8, background in my SX20 become a blue large clock. I really want to have a different background but cannot find the way how to change.

  Any help would be appreciated.

  Thank you.

  Sincerely,

  Bagus Hanindhito

  After you connect the 8 Touch, you can still use the remote control, you will need to put on the SX20:

  SystemUnit MenuType experimental configuration: full

  I think that the standard background when using a touchscreen device is what you see, blue with large clock.  However, after the MenuType return in full which will give you the full OSD which is used with the remote and not that of the button, you may be able to change the background then.

• Activation of presence on the web setting in cisco telepresence SX-20

  I have EDT cisco telepresence SX-20 devices, want to allow the web presence but the poster ' mistake: it will be changed setting OSD "guid .pls myself

  What setting exactly are you trying to change?

• Replacing Cisco TelePresence IP gateway series

  Hello

  What product replaced the Cisco TelePresence IP gateway range?

  THX

  According to the announcement of end of sale and end of life for the gateway IP Cisco's TelePresence

  There is no alternative available for the gateway IP of Cisco TelePresence at this time.

• Cisco telepresence video Communication Server (VCS) - compatibility CTX X8.1.1?

  The Cisco TelePresence Exchange System compatibility matrix (CTX) does not cover version of VCS X8.1.1 (to solve the problem of software). Version X7.2 is recommended and supported which is affected by "heartbleed".

  X8.1.1 compatibility is tested by Cisco and the updated matrix?

  In fact we run CTX v1.3 with VCS X7.2 and solve the problem of software without leaving the support. What is the recommendation of Cisco?

  Kind regards

  C.Opwis

  You could improve your VCS to X7.2.3 which includes a fix for Heartbleed.