Raspberry PI installed correctly on LabVIEW 2014 with LINX 3.0 (yellow warning)

Similar Questions

• Not compatible with Labview 2014 IMAQ?

  I try to work with a National Instruments / SuperDroid Robots SD6 ( https://decibel.ni.com/content/docs/DOC-18528 ) now... Everyting connects fine using LabVIEW 2014 with the module of Robotics with the exception of the functionality of the camera. When you use the solutions provided LabVIEW cannot find dependencies IMAQ.

  I checked to make sure that I have the module installed and I see IMAQ 4.9 and IMAQdx 4.3.5 MAX

  Check the newsletter below on the compatibility of the IMAQ, she only has not 2014 listed

  http://digital.NI.com/public.nsf/allkb/DB928F6D5E9D6B97862579A7006B2850

  Specifically, I need the 2014 Image processing module version in the link below. The download link says 2013 and during the installation process, I don't see an option for support for 2014.

  http://www.NI.com/gate/GB/GB_EVALTLKTSIGPROC/us

  Is there a trial version of this software that is compatible with LabVIEW 2014?

  I was able to get in touch with a sales engineer and I need to image processing module is not yet available for LabVIEW 2014. Where my question.

• LabVIEW 2014 SP1, hardware and real-time PXI

  I'm doing my third LabVIEW Wipe/reinstall in as many days, completely frustrated (and after several calls an hour with the support of NEITHER).  Here's the situation:

  I wrote a fairly large (1000 VI) project of Acquisition/control of our graduate students data used for behavioral experiment on sound localization.  It was developed in 2012 LabVIEW with the module running on a PC/PXI system real time.  It worked very well and was brought successfully under LabVIEW 2014 (with upgrades comparable to the software of the PXI.

  About 18 months ago the students began to write their theses, and at one point stopped gathering data.  Also, at some point, I upgraded the software on this system to LabVIEW 2014 SP1, but I am not sure that I never tested my software with this new system.

  This week, I pulled up the system to use MAX to open some test on the PXI multifunction and DIO card panels to control manually one of the stimuli.  I discovered that MAX could not communicate with the advice on the PXI system - he attributes them as devices VISA, indicating each Board with an icon with a red X means that he could not communicate with the IP that I had assigned to PXI.  Yet, MAX (a) could "discover" this PXI, (b) MAX can 'see' its IP address, and (c) Windows could not only Ping the IP, but could FTP on the drive of the PXI and I could move files back and forth.

  I did two sequences complete "Wipe/reinstall" using LabVIEW 2014 SP1, all giving the same result.  I know it has worked in the past, including when I installed LabVIEW 2014 (without SP1), something I repeat myself now with my third installation.  I discussed with OR (thin?) possibility that there is a "hidden defect" in the Distribution of the SP1, one that is visible to LabVIEW RT users using PXI hardware and go unnoticed because (a) install a few sites of LabVIEW versions SP1, (b) a minority use the RT Modules and (c) PXI is "old material".

  If anyone has such a system or saw a similar problem, please answer.  I'll do a follow-up post if I managed to 'fix' my system by this last reinstallation "a solution of worked before."

  Bob Schor

  Well, the answer is that, in my system, LabVIEW 2014 SP1 with LabVIEW Real-time connected to a PXI system does not appear to connect to boards plugged into the chassis.  Returning to LabVIEW 2014 (fall release), installed in exactly in the same way that the three failed attempts of LabVIEW 2014 SP1, works immediately.  Engineers OR will try to duplicate/verify/possibly patch? in this issue.

  Bob Schor

• Instrument i/o Assistant not installed correctly. No driver file not supplied with the student of Labview version.

  I installed the student version of Labview and the installation of 99%, there was a window that came.  The image just below this sentence "Installer of year DVD drivers NOR the device" at this link: http://www.ni.com/gettingstarted/installsoftware/instrumentcontrol.htm is the window that opens.  Now the problem is that I don't have a driver cd.  I downloaded a student version: http://ftp.ni.com/evaluation/labview/ekit/other/downloader/2012LV-WinEng_downloader.exe .  It is an installation file.  Then I tried to download a file of drivers, I came here: http://joule.ni.com/nidu/cds/view/p/id/3145/lang/en and I used the exe file that stores a file on the computer.  The record is just full of stuff like .bin files ect.

  I then reinstalled everything after you have uninstalled it and return to 99% a few times, and the same window came that I listed above.  I try and tap the window the the location of the driver in all folders.  None of them work.  I even tried pointing to 488,2 records, IEEE and Visa, I downloaded and they do not work.  This message in red in the window remains, 'the specified folder does not contain the correct volume' and it gives you no idea what its looking for.  So I just said to skip that part and it finishes the installation.  I put in my access code and that seems to go ok.

  After installation, I install the drivers IEEE and Visa 488,2.  Visa seems to include the wizard of e/s to istrumentom some how, but it does not solve the problem I describe below.

  Then I go in and launch Labview and I start a project and go in view the block diagram.  I'm going by dragging in the "Instrument i/o Assistant" to connect a voltmeter of pcib-usb. When I double click on the "instrument I/O assistant" window "Measurement & Automation Explorer or the instrument i/o assistant isn't installed correctly.  Please install these on the LabVIEW driver CD.  But even once, I downloaded the driver CD seems unnecessary.  The directory of the driver folder is NI Device Drivers > Aug12 > Products > "a whole series of .msi files and .cab files ouch.

  All I need is to access the Instrument i/o Assistant so I can set it up to connect with an instrument, I can be sure my program communicates properly with an instrument.  However, this is the 3rd day in the struggle with this program.  I was too frustrated this post yesterday and I'm feeling much better today.  Any suggestions on how to get this set up correctly?

  Yes! Yes! ... sigh Yes... problem solved.  Aparently the driver download was not complete and it was not obvious until he had not downloaded part 2.  Therefore part has been downloaded drivers and it solved all my problems.  Choir of angels chimes in "Haleluah!"  OK thanks me and all wizards!  Pats me on the back.  Job well done.  o / glad I could get that off me chest.  And to think that some people paid, others to be able to listen to them talk to themselves D hehe.

• Cannot install Datalogging and supervisory 2014 control with labview 2014 64-bit Module

  Community salvation OR

  I installed labview 2014 64 bits, then I tried to install Datalogging and supervisory Control Module 2014

  http://www.NI.com/download/LabVIEW-datalogging-and-supervisory-control-module-2014/4848/en/

  but a display of error messages "labview 2014 must be installed. What I have to install labview 2014 32 bit, is there another solution

  In addition to morem, try installing real-time 2014

  http://www.NI.com/download/LabVIEW-Real-time-module-2014/4832/en/

  an error message display "labview 2014 32 bits must be installed". is there any version for 2014 lv 64-bit

  Thank you

  The compatibility matrix is here.

  You must install LabVIEW 32bits.

  You have a specific need for 64-bit LabVIEW?

• allow to create or write a PDM file with labview 2014

  Hello

  I need help. I'm new with LabView. I tried to create a PDM file, but it does not work. My code in the link below is really simple, but I don't know what the problem is. My code doesn't throw any errors so I don't know what to look for in the internet. Once my code is excuting, no file is created. I use LabView 2014 and my laptoop has windows 7 on it.  My question is, in all I need to do whenever I create a new VI of specific configurations that will be play/create/write a .tdms so that my code may work correctly because the writing in a .txt file works perfectly.

  Thank you and sorry for my English

  Hi bmtanguay,

  you want to run your VI on your cRIO9074?

  Where do you think your cRIO creates this file? A cRIO is a clean computer - and it has its own 'hard drive '. This is where your file is created: C partion on your cRIO!

  You cannot create a file on your Windows pc from a VI running on your cRIO!

• 'Lack of installation files' then install LabVIEW 2014 (Win7-64 on a VMWare system)

  Hello

  I try to install LabVIEW 2014 on a VMWare Windows 7 - 64-bit environment, with no luck.

  3-DVD installation media has been downloaded from NI.com, the release of August 2014 of the Site license academic (ASL), which my company is a regular subscriber, a very long time.

  (Interestingly enough, this same virtual system has fonctionnee LV 2012 without any problem whatsoever)

  Here are the steps I followed:

  -unzip the 3 iso files on separate directories on drive virtual, principal of this system;

  -Run setup.exe on the first directory (IE one that contains 1 DVD files)

  -Enter the serial number of the FSA

  -l' Installer leaves just selected default English 2014 LabVIEW and the Manager of Package of VI, so I expand the ASL Core Software to add NIDAQmx 2014, and I also selects the device drivers OR - August 2014

  -J' I accept different license agreements

  -I select "I am not the end user" to postpone activation

  Setup continues but almost immediately alerts telling me that it was impossible to install "NI Customer Experience Improvement Program", Yes , I want to keep and then I see a system dialog box display of files/paths that do not actually exist on the directory DVD 1, hence the obvious error 'lack the installation files"message. If I ignore this message, several other similar dialog boxes appear.

  Either by the way, I've done various research, but, right now, apparently not a popular question at all.

  Any advice?

  Problem solved.

  For some weird reason, WinRAR do NOT extract some files from the first archive .iso (but more importantly, she also didn't show absolutely no error message, leading me to believe everything was fine).

  When any further inspection, I found about it and made extraction .iso process everything again and this time to the installation program completed without fault.

• I want to connect my Macbook Air (IOS 10.9.5) with my amp stereo House (TEAC I-501DA), which has a USB connection. I followed the steps described in the manual TEAC to install the driver and my Mac says it is installed correctly, but it does not appear I

  I want to connect my Macbook Air (IOS X 10.9.5) with my amp stereo House (TEAC I-501DA), which has a USB connection. I followed the steps described in the manual TEAC to install the driver and my Mac says it is installed correctly, but it does not appear as an option in the preferences/system sounds.

  Version 1.1.2.2 El Capitan driver support, then why don't upgrade you your MacBook Air to El Capitan?

• I need to download a VISA driver even with Labview 2014

  My problem: I need Labview 2014 to receive data over UART connection (on a windows pc 7). Do I need to install drivers for it NEITHER Visa or they are already integrated into Labview 2014?

  Yes, you need to install the VISA drivers.

• my computer is connected to a new projector with a DVI and HDMI cable, and return the currency I installed correctly but I don't get a picture on the projector

  I connected my computer to a new projector with a DVI and HDMI cable, and return the currency I installed correctly but I don't get a picture of the projector, need HELP.

  Hi Bill,

  Thanks for asking this question to Microsoft Community.

  I will definitely help you to set up the projector, but before starting, I would ask you some troubleshooting questions.

  What version of the Windows operating system is installed on the computer? Do you get any error messages? Have you done a recent software or changes to the material on the computer?

  Here is a link that provides information on connecting to a projector. Go through it and check if it helps.

  Hope this information is useful and provide us with more information for further assistance. We will be happy to help you.

• LabVIEW 2014/2015 break with my library of wrappers

  I have a lot of LabVIEW package screws saved in LV8.6 library, they almost all containing call library function node. Recently, I was working on a new program that uses these library live I have found that when you use these screws it causes LabVIEW to crash. Accidents are not due to errors of execution, but can occur during execution and development (is not running).

  Here's my sympthoms with different versions of labVIEW.

  • LabVIEW 2010 - these accidents do not happen at all.
  • LabVIEW 2014 - blocks most of the 3 versions I tested it. LabVIEW has crashed on me when you press "save all", "run", "exit / close ', double click on a Sub VI to open it (the library VIs and SubVIs new for the new program).
  • LabVIEW 2015 - seems to be a bit more stable then 2014. I only noticed crashes when you press "save all" and "exit/close.

  I tried the following

  • I read on the forums that opening the screw with a new version, massive compilation and save for precedent could solve the problem. I tried with no luck.
  • Mass, compilation of all screws of 8.6 library into the new version of LV before trying to use them in an application. This has no effect either.

  Is labVIEW a problem or a problem with my screws?

  And how assign you the string that you pass to the second parameter? All wiring a string constant empty for her? While in the LabVIEW code you don't have to worry about memory allocation before calling some other VI, it is certainly not true when calling C functions. Function wants to write information in this string, and for that to work (You on the LabVIEW diagram) caller must allocate sufficient storage space for it.

  We must know in the documentation of the API, which is the maximum size of the buffer and allocate only a large part of the size of the string. There are two ways to do

  (1) use a table this is initialized with a U8 as input and the right type amount for the size of memory buffer and dressed it with an array of bytes to the node of the chain.

  (2) see you Minimum size in the configuration dialog box? Enter the number of bytes that the string must have at least according to the documentation.

  To answer the inevitable question immediately. Yes, he didn't plant in LabVIEW 2010, but did corrupt the memory and anyway somehow there yet. Any alteration of the memory immediately translates into an accident. There are several possible outcomes of these corruptions and they can change according to the computer that you run your application, the amount of available memory, the moon phase and how your emotional state is right now (the last two are not very serious but also quite unrtrue). The layout of memory at the moment when your running can much influence what happens to these alterations. It can produce results strange and inexplicable in your program when the actual data values that are store values in wires are crushed, or your screws can get corrupted and if save you them to the disc later get unreadable, or the computer produces a dialog error box much later, when you try to stop your app and LabVIEW , or it seems nothing happens (but is still of corruption there not only to bribe vital data in memory).

  With the change to LabVIEW 2014 layout changed memory somehow, perhaps due to optimizations more aggressively in this new version and all of a sudden your DLL overwrites a memory very vital for the operation of your application in LabVIEW.

• Five of the six updates have been installed correctly, KB2698365 failed with error code 80070570. What should I do to install this important update

  Five of the six updates have been installed correctly, KB2698365 failed with error code 80070570. What should I do to install this important update successfully. I'm not a pc expert and don't have no knowledge will take it the word of experts from the pc. KB2698365 is 'important', so I tried to install it several times, but always failing with error code 80070570. I've been on a boring treasure hunt for to install this 'important' update, it seems to find no will to give helpful advice anywhere. I would appreciate help installation of this major update, and talk about normal advice, how to install it successfully without failure of the error code 80070570. What is the error code 80070570.? I use windows vista Home premium, service pack 2, 32-bit operating system. I'm using the essentials of security. Thank you for the consideration of this issue. NIC

  Hi, Grizzly7659,

  Follow the instructions given by Taurian & guenoun

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_other-windows_update/error-code-80070570/a2df7d06-BE9B-4554-b796-c52fac838842

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_other-windows_update/error-code-80070570/51c5b0d3-BFDD-4f69-bff7-623954866b59

• Problem with Age of Mythology "MSXML 4.0 is not installed correctly. It is necessary to run the game.

  I have a problem with Age of Mythology. Whenever I try to start the game after installation I get the message: 'MSXML 4.0 is not installed correctly. It is necessary to run the game. »

  I tried everything: re - install, install the parser MSXML 4.0, to open it in safe mode, compability mode and have tried the troubleshooting of the control panel. Is it possible to fix this? I have the original game, but I bought it just as it came out. Y at - it another version of the game for windows 7(64bit) or it is impossible to make it work?

  Hello
  I suggest you to install the latest version of MSXML 4.0 available and check the status. If the update does not work, then uninstall all MSXML versions that are available and install the latest version.
  Microsoft XML Core Services 4.0 Service Pack 3. Download the link available in the following article.
  http://support.Microsoft.com/kb/973685

• Cannot install LR 6 DVD on Macbook Air with OS 10.11.2.  Installation crashes and ejects the DVD at the end of 98%.  Long note that 'Adobe application manager quit unexpectely', restart.  DVD installed correctly on my IMAC.  That is what it is?

  Cannot install LR 6 DVD on Macbook Air with OS 10.11.2.  Installation crashes and ejects the DVD at the end of 98%.  Long note that 'Adobe application manager quit unexpectely', restart.  DVD installed correctly on my IMAC.  That is what it is?

  Copy the contents of the drive in a desktop folder and install from this directory.

• Problems with the Dreamweaver modules being installed in Adobe CC 2014 - OSX 10.9.5?

  I tried to install two Add-ons (photo gallery for DW and Adv CSS Menu Light) for Dreamweaver CC 2014, but I get an error notification, stating that they are incompatible with the installed Adobe applications.  Two of these state modules they are compatible with Adobe CC 2014, which is what is installed.  I am connected with an administrator account.  File synchronization is activated.  I have Adobe CC Desktop App 1.9.1.474 which seems to be the latest version.  It is on an iMac 27 "mid-2011 running OSX 10.9.5.  All the updates of the system have been applied.  I tried uninstalling and reinstalling several times with the same result, add-ons on seven different computers of the same generation/image.  It is in a class.  Any recommendations on other things to try?  Any help is very appreciated!

  It turns out that we had a bad deployed package.  After pressing a packet update Dreamweaver CC 20141 (via Casper), us were able to get these add-ons installed.