Re: Error message board Messagedu - HARD drive

Similar Questions

• After the upgrade yesterday from Vista to Windows 7, now my Cisco VPN does not work and I get an error message titled: grounds 440 driver fault. Any ideas to fix this?

  After the upgrade yesterday from Vista to Windows 7, now my Cisco VPN does not work and I get an error message titled: grounds 440 driver fault.  Any ideas to fix this?

  This was the solution!  The works of vpn as $ 1 million now.  I followed the instructions above to enter the uninstall program and selecting the repair option.  I rebooted the machine, then used the troubleshooting on vpn software compatibility option.  Selected Windows windows xp (service pack 2) as the correct software and cisco vpn client started right up.

  Thanks, Nick!

  Rick

• Windows gives me an error message that the selected drive has been "marked as potentially damaged - check disk before use as back up.

  I am trying to set up a window to the top-

  -follow the instructions of top to select a backup disk - I did
  -Windows gives me an error message that the selected drive has been "marked as potentially damaged - check disk before use as back up.
  -in the past, this disc has been used ONLY as a backup disk
  -When you try to check (after Windows links) a message tells me the drive cannot be checked while it works - I have no problem with understanding that.
  -I wonder so I wish "disassemble this first volume" - "... all handles opened to this volume will become invalid..."
  -Do not understand what was required - and having no idea of the consequences (the disc 'way up', and what happens to the invalidated handles?) I replied "Cancel".
  -l' screen after you ask then if I want to check for errors at the next startup of my computer - I clicked on the button "schedule disk check.
  -When I started my computer nothing happened - what happened to "schedule disk check? How can I check the disc when firstly, it seems to be 'in service', but is only a backup to disk, and I thought that it only came into use when the reverse began to run?
  (I also tried to leave a message on one of the FAQ pages on back ups, but it appears that the number of characters is set to limit so low that you can't describe why the FAQ response is considered to be "not useful"
   
   
  Original title: Back Up system - disk and check

  Since this is a secondary drive chkdsk/r can be run without having to reboot.   Close all the programs that can access training and and when you run chkdsk say yes to "remove this volume first...". ».  This will cause no harm.  Although not strictly necessary, I recommend you to reboot once completed the disk check.   This will solve any problem related to the file handles.
  If chkdsk/r reports bad sectors, you should replace the disk.

• error message iTunes displays locked drive, itl locked files, or do not have administrative privileges on the PC after a clean install of Windows 10

  Yesterday I did a clean install of Windows 10 on my PC with a backup of the hard disk external. I downloaded iTunes, but get an error message that the drive is locked, the .itl files are locked, or I don't have administrative rights to these files. I deleted and reinstalled the PCI DSS several times correctly in the PCI slot hoping that would be a solution, but to no avail. I am the only user on this computer and do not have administrative rights. Any help you can offer will be appreciated. Thank you

  This can help (from turingtest2):

  Fix iTunes for Windows security permissions

• I try to start the old T2150CDT - error message "not found reading drive C of the sector.

  Hello

  I came by one of them and trying to fire, but I get the message, "sector not found reading drive C". I get this message just after windows 98 logo appears.

  Problem is that I am limited in what I can do, because I don't have a floppy drive and back does not recognize the CD drive (missing drivers); Although I can hear it when starting upwards.

  So I out the HARD drive and pasted the installation windows 98 inside files. then tried to reinstall, but I still have the message of "sector not found reading drive C". The drive is too large (it's about 2.1 GB.)

  Install the right drivers for the CD Rom would allow me to install from a CD?

  It works usually
  Thank you
  John

  As far as I know the error message; "Sector not found reading drive C" appears because of these three reasons:
  -physical HARD drive failure
  -corrupted HARD drive file system
  -Bad RAM

  In the first case, you should try to format the whole HARD drive and should try to install the new OS.
  If it will not help, chances are that HARD drive is malfunctioning and needs to be replaced.

• Pavilion 23-f221ea: Setup error of Windows 8 hard drive refurbished

  Hello

  I posted a similar message last month, but it is a new issue.

  I start with a completely fresh SATA hard drive, purchased yesterday and the recovery that were sent to me by HP disks.  I think that I have can I have inadvertently damaged the last new hard drive he began to throw up a lot of mistakes 'disk fail.

  I was expecting, it's a straight forward case this time, but I was struck with the following message appears during the recovery process: "Windows could not restore your computer by using the factory imagebe"

  I followed the advice of this guy: http://h30434.www3.hp.com/t5/Desktop-Operating-Systems-and-Recovery/Recovery-Manager-could-not-resto... and got an iso disc of Windows 8 (maybe 8.1).

  I started with the iso disk and followed the instructions on the screen until I was asked to choose the installation location. I chose the one and the only displayed 1 TB drive, but after nearly 30 minutes, the installer said "Windows is unable to install to the selected location. "Error: 0 x 80300001.

  I thought that this new disc may need partitioning and/or formatting, but I tried it via the command prompt only to be presented with another error - IO error. My hands are essentially firmly tied behind my back now.  I feel like I'm just opening a long line of Pandora's boxes at every turn!

  This time, I was convinced that, with a new batch of discs of HP Receovery official, it would be simple veil--what a mistake!

  Please can someone save me?

  Hello

  My thoughts are to delete all partitions, select new. Windows will create all the required partitions.

• Error 1 full (305) hard drive with dv6-6119tx - is it worth to replace the HARD drive?

  Hello!

  I bought the mobile entertainment HP Pavilion dv6-6119tx (QB365PA) in July 2011. The specifications are - processor: Intel Core i5 - 2410M, integrated RAM DDR 3 4 GB, HDD: 640 GB (Toshiba) operating system: Windows 7 Home Premium x 64

  Since I bought this machine it has been giving me problems in time. First webcam died within the first 2 months, then the DVD recorder failed then it was the keyboard and finger print sensor. There were several problems with the installation of microsoft update. Six months ago, I replaced the 6-cell battery. I bought a costly maintenance contract for the second year, given the number of aging I met within the first year of use. Apart from the battery which was of course not covered under the contract, I had no other problems in the 2nd year. And just as this contract expired in August of this year I started facing problems, I got BSOD on two or three occasions. After each incident system booted normally and everything was fine except the Device Manager indicates problems with infrared devices consumers. The problem seems to have exploded on its own. Then since the past two months, my computer started freezing during startup and for initial 5-10 minutes. After startup. In this duration, I checked several times HARD drive health using the utility BIOS InsydeH2O repeatedly. The time required for the diagnosis seems to be gradually increasing with each analysis later but he still passed diagnostics. But today, when he sent 'Hard disk 1 (305) full' message and yet I am able to boot but with freezy start-up. Today, the system froze in the middle of something twice and I had to stop hard. When I ran Avast! It froze at 99% on detailed analysis. He struck the syswow64 folder file and showed an infected file.  I have run windows error checking-HD and it showed no errors.

  My questions are-

  1. what seems to be the problem? What is a HDD failure or infection?

  2. is it useful to replace the HARD disk if the problems are the result of HARD drive problems?

  3. I argued my sytem on external HARD drive, I can install Windows 7 on new HD, if get a?

  4 system backup of files is only 274 MB in size, is this good?

  5. If I purchase the new hard drive has the same specifications and manufacturer as the current one or can I update? If I can update what are recommended replacements?

  Hi KlebersonofGun:

  Thanks yo for your answer.  I send you a link to the Guide "Maintenance and Service" for your computer, click here. Page 62 has a section on the replacement hard drive

  You can use any brand of hard drive, as long as it fits the plug.

  I hope this helps.

• Windows Setup could not configure Windows on hardware of this computer Installation error on the new hard drive

  Okay so if please bear with me and be patient.  I'm not tech savvy.  I know enough to be able to remove an old hard drive and put another one, but when there are errors, I don't know what to do.

  Here's the situation.

  I have a Dell Studio XPS with Windows 7 installed.  I started having these notifications that my hard drive could be a failure.  I tried everything that I could find to fix it without having to buy a new HARD drive without success.  The current system has a 1 TB Seagate hard drive.  I installed a memory additional bar thingie right after that I got the computer about 4 years ago.  (If someone tells me how to find the properties of real system, I post them if necessary).  Anyway, I bought a new WD 1 TB black disk hard to install before my old dies and loses all my photos and documents, etc...

  I took the old drive yesterday and installed the new hard drive.  I put back the case and turned on the machine.  I put in my Windows 7 installation disc.  He began installing Windows 7... It's completely past the initial screen where it says it to load it and the other... I had accepted the license agreement, but did not have to make a profile and do the work and the reader.  I hope all this makes sense.  Then it pops up this message "installing Windows could not set up Windows on hardware on this computer."  I couldn't figure out what to do from there.  I got the new drive and put the old one back to and here I am. I tried to find solutions to this problem, but I either don't can't make heads or tails out of the responses on the internet or the solution is not exactly my problem.

  Please help if you can!  And if you have any suggestions, please dumb them down so I can understand what to do.  I CAN do if loaded, you just have to not talk too irritable.  Laughing out loud

  Thank you in advance!

  Maybe not...

  The Windows installation is not happy about something, and since it gets at least started which is a good thing, but your installation problem can not really be with Windows - perhaps something about Dell hardware or your 1 TB HARD drive.

  I looked at your system and found this article that you can read to see if it sounds like your original question:

  Windows Setup could not configure Windows on hardware on this computer.

  http://www.Dell.com/support/article/us/en/19/SLN293812/en

  Since Dell has written an article for help on this subject, it means they've met enough times to take the time to compose the article and put it on their WWW site (but, they say, it is a possible resolution).

  Could you take the issue in the Dell online community where experts hang out (especially your amber light).

  Another good place for support is www.bleepingcomputer.com where there is a similar topic as your question (except Vista) on a Dell and a new disk of 1 TB (also a Seagate) and Dell ideas did not work, but someone else has found a way to fix it:

  http://www.bleepingcomputer.com/forums/t/453378/installation-fails-to-complete-on-new-HDD/

  The bleepingcomputer for your error message search reveals other areas and people who have got things to work in different ways, then it is perhaps another place to look for ideas.

  If the installation still fails it would not hurt to do the BIOS setting and see if things are getting longer, and since you are going to write the current settings before proceeding with the adjustment you can always cancel the adjustment if things get worse.

• Error retrieving Tecra A6 (hard drive not found. Error: F3E1000001)

  Hello
  I want to recovery my Tecra A6, but when I insert the first (of three) DVD and restart my system to get to the recovery

  Menu (when booting from the recovery DVD) just rebooted my laptop and every time I try this (very simple procedure) this

  happen again.
  That's why I tried to get it back to Win XP > Toshiba Recovery Wizard... in the first DVD in the 'BIN' folder there isn't

  a "RECOVERY.bat" batch file when I run this file will open a CMD window and checks are willing (and then the

  following text is displayed in the CMD window :)
  "
  Verification of DMI
  Verification of RAID
  Failed to initialize the raid class.
  Check the HARD disk
  End of the error
  "
  and a new window opens with the following text:
  "
  
  an error has occurred.
  Error: F3E1000001
  Hard drive not found.
  Please press [OK] to turn the computer off.
  "
  If I press OK the any immediately goes down (without shut down windows) and I have to restart.
  Also my laptop works properly my recovery DVDs sounds great, I want to just recover my system because of the speed more

  in Win XP.
  Maybe there is a new firmware for my HARD drive or an update of the BIOS so that the laptop could detect my HDD.
  In Device Manager, my HARD drive is: HTS541010G9SA00

  Wait a minute: you try to run recovery as OS installation?

  The recovery procedure must be on path:
  Turn on the laptop and press the F12 key
  When the bootable devices appear put the first media for recovery in the optical disc drive
  Choose CD/DVD media from the list and press ENTER
  Follow the menu on the screen.

• How can I fix error code 2000-0145, hard drive dst

  When I quit Windows, I get the "End program" dreaded error. I usually get several times until the machine stops in fact. Windows XP

  Sounds like your hard drive is a failure.  Check with the manufacturer of your PC error code and see if they have the diagnostic software that can run on your computer to diagnose the problem.  This isn't a Windows error, it is a hardware error on your computer.

• "" Unknown device is error message "is not a driver" when you run Microsoft Fixit Center

  Original title: driver problem

  When microsoft fixit center running, I get a message that says ' unknown device is not a driver.  What should I do?

  Hello Stephanie,.

  Welcome to the community Microsoft and thanks for posting the question.

  According to the description, it seems that you are having problems with Microsoft Fixit Center. "As I understand it, you get an error message" unknown device is not a driver.

  I need to ask you some questions to help you better.

  1. why you use Microsoft Fixit Center?

  2 do you have connected a device to the computer apart from keyboard and mouse?

  Reply with answers to help you in a better way.

• To remove the error message about the network drive

  I have W7 Home and recently restructured.   I had this problem of reformatting finally a long time ago and it is solved but do not remember how.  Whenever I boot, I get the message "connection impossible network drives.  When I click it, I see the Epson printer has a red X on it and says Epson memory card.  The printer has always shown in my computer, but it works very well.  All I need is to get rid of the error message.  I tried to go into the center of the Action and unclicking on error messages of network firewall but that did not help. I'll print on any solution this time for the next restructuring!  Thanks for any advice.

  Epson support says that since the printer connecting wireless much later that opens Windows, Windows is not see when it starts.  They say that it is a Windows problem, not them.

  To get rid of the error message, I disconnect a right-click on my computer and clicked on the network drive.  I find the error message disappeared and the printer works fine.  I don't know if there's a problem with that.

• How to recover contacts from Windows live mail email messages from the hard drive.

  I was download my messages to e-mail AT and T through Windows live mail (Pop3). My computer has a hardware problem and stopped working.

  However, the hard drive is fine and all the data is safe. I now have a new computer. How can I transfer old computer to the new e-mail and messages

  Windows live mail in the new computer can actuall import the old e-mail messages and contacts.

  Plug the old drive to the new computer.

  You may need to show hidden files to see the records of WLMail.

  olddrive:\Users\old Live Mail

  Drag and drop messages into an open folder of WLMail.

  If you have been given a copy of messages on the AT & T server you have duplicates.

• my computer failed and I need to recharge the 13 elements, I crossed and downloaded but error message says unsupported c drive?

  I downloaded 13 items but can't make it work, error message: drive C does not?

  John

  you have a mac with case-sensitive drive?

• Presario continually offers the error message 'space' insufficient on drive D: (CD-ROM). How to fix?

  During my first backup via Presario backup on the CD-ROM drive (D), I ran out of discs and decided not to continue. But the Presario guard operating system throw up error messages drive D is "saturated". The drive is empty since the abandonment of the backup two weeks ago. How can I tell Presario to cancel the backup, or whatever it takes to stop the error message?

  I'm sorry I don't exactly understand the problem you are having... can u please develop once more?