Re-installation of operating system could not and cannot start the current operating system?

Similar Questions

• Updates do not install, Sections of Vista does not and cannot start the Audio Service

  I try to install the updates on windows update but important as the service package 2 do not work, they start then stop and say failed code "WindowsUpdate_80070643"

  boxes keep popping up saying some files are damaged or not installed properly and that I should reinstall as a file call... system32\AVRT.dll. Windows Media is not no longer works.

  My Audio service is not running, I'm not sure that there is a problem in microsoft windows but the button to switch on the audio does not, and a box pops up saying it does not yet have another pop up says that everything works.

  any help? Please

  Hello
   
  a. updates have you tried to install?
  (b) button to switch on the audio of your computer are you using?
  c. what exactly happens when you try to run any audio/video file?

  You can try the steps outlined in the article below and check if this help.
  http://Windows.Microsoft.com/en-us/Windows-Vista/Windows-Update-error-80070643

  For audio problem you are trying to run the troubleshooter which may help. It search common problems with your volume settings, your sound card or driver and your speakers or a headset.

  1. open the troubleshooting of Audio playback by clicking the Start button, then Control Panel.
  2. in the search box, type troubleshooting, and then click Troubleshooting. Under hardware and sound, click on the audio playback problems. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  http://Windows.Microsoft.com/en-us/Windows7/open-the-playing-audio-Troubleshooter

  You can also try to update check you and sound card driver if it works. The article below will help you do.

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Also, check if the following services are set to automatic.
  a. Windows Audio
  b. Windows Audio Endpoint Builder

  Here's how:
  1. click the Start button, type services.msc and press ENTER.
  2. go to any services mentioned above at the same time, right-click on it and select Properties
  3. click on the tab general, select automatic for startup type. Also click the Start button, if it is not started.
  4. click the Dependencies tab and make sure that all addictions services are set to automatic. Then click on the OK button.

  After return to that exact error messages we can help you better.

  Let us know if it works.

  Kind regards
  Umesh P - Microsoft Support

• Help, please! A master hard disk partition information lost and cannot start the Vista system

  I have Vista with my dell desktop computer.  I guess I got a virus that has deleted/messed my main hard drive.  All of sudden my computer was dead and when I try to restart, I found I can't boot the system.  I loaded the DVD for the resettlement of Dell to come with the computer and try to install it.  But it shows "Disk 0 unallocated space" with 222 GB and 'Disk 0 Partition 2 Recovery' with 10 GB.  I could not install Vista on the first, as it says "Windows must be installed on a partition formatted in NTFS.

  How could I solve this problem?  I could not allow me to format the drive because there a lot of data, that I just can't lose.

  Any help is very welcome!

  Marco

  http://support.Dell.com/

  Problem with the recovery process, contact Dell at the link above.

  It's recovery process from Dell, NOT Microsoft.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Try this to save your data:

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon...

  Mick Murphy - Microsoft partner

• Install the new windows 7... The message "Windows Installer... windows could not retrieve information about the disks on this computer" no operating system on the pc only thanks

  New installation,

  Windows 7 x 64 (OEM)
  Card mother Gigabyte GA-A75-D3H
  Load os first time and no problem had pc upward and work... Has had a drive failure and to reinstall the operating system on a new hard drive but get the error message.
  Have disabled CMOS and BIOS flashed but still have the same problems...
  Any help much appreciated...
  Steve :(

  Hello

  You use the installation disc for the full version or an upgrade disc?

  You can see the following link.

  http://Windows.Microsoft.com/en-us/Windows/help/install-reinstall-uninstall?SignedIn=1

  This could be a problem with your hard drive. You can contact the manufacturer of the hard drive for better assistance.

• HP G62-B50SA: HP G62-B50SA Recovery Manager could not and cannot restart Windows 7

  Yesterday, I threw the Manager of recovery to re - install a release of version Windows 7 box.

  1% of the installation, I get the following error error code: 0xe0ef0003

  After this error, I could not start Windows more BOOTMGR missing

  I tried to press ESC, then F11, but once more, the process has failed

  I had also created recovery CD (in Total I have 4), I try to reinstalled with them by going to F9 and put the CD to be the first boot.

  I get the following error message "this computer does not support the system recovery media. You are not able to restore the system with the media".

  What should I do next?

  Thanks in advance for your help,

  Concerning

  Hello

  Here is another solution, you can try.

  Before you try the following, make sure that you can still read all the key character product activation 25 on your label Windows COA (5 blocks of 5 alphanumeric games).

  An example of a COA label can be seen here.

  You can create a Windows 7 installation disc yourself using another PC - just download the Disk Image correct ( this must be the same version that originally came with your laptop - it is listed as Windows 7 Home Premium 64 - bit ) from the link below and use an app like ImgBurn ( Note: you can deselect additional software during installation of ImgBurn offerings) to burn the ISO correctly on a blank DVD - a guide on the use of ImgBurn to write that an ISO on a disc is here.  The source of the Windows Image is Digital River.

  Windows 7 Home Premium 64 bit SP1.

  Use the disk to perform the installation, enter the activation key of Windows on the label of the COA at the request and once the installation is complete, use ' 'phone Method' described in detail in the link below to activate the operating system -this made method supported by Microsoft and is popular with people who want to just have a new installation of Windows 7 without additional software load normally comes with OEM installations.

  http://www.kodyaz.com/articles/how-to-activate-Windows-7-by-phone.aspx

  You may need, additional drivers and software are here.

  Kind regards

  DP - K

• Cannot defragment the hard drive AND cannot start the computer in safe mode

  I have been unable to defragment my hard drive because it tells me that chkdsk /f planned.  I tried manually works in command mode nothing works.  I was advised to try to start up in safe mode, but when I do that all I get is a screen of command lines, and my computer freezes there.  What I'm doing wrong and what I can do differently?

  If you try to defragment a volume and see a message like this:

  Disk Defragmenter has detected that Chkdsk is scheduled to run on the volume: (c :))
  Please run Chkdsk /f.

  This means that the volume (disk) that you want to defragment was marked 'dirty' XP.

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a working CD/DVD (internal or external) drive?

  You have a genuine XP installation CD bootable, which is the same Service as your installed Service Pack (this is not the same as any recovery CD provided with your system)?

  You can check the status of your bit of impurity from a command prompt window.

  To do this, click Start, run and enter in the box:

  cmd

  Click OK to open a command prompt window.

  For example, to query the bit of impurity on drive C, type:

  fsutil dirty query C:

  The sample output:
  Volume c is dirty
  Volume C: is dirty

  Is the volume of your sale or it is not dirty?

  The only way to disable the on a volume's dirty bit is to run chkdsk with error correction.

  You can click on start, run and enter in the box:

  Chkdsk /r

  Click OK and answer Yes to schedule the chkdsk next time XP restarts, restart your system and keep your fingers crossed that the chkdsk /r clears the dirty bit (you may need to run once or twice).

  If who disobeys, then you will need to start in the XP Recovery Console and run the chkdsk /r from there.

• Repair disk Vista not working does not and cannot correct the disk error

  Hello. I have a disc error and my vista repair disc does not work and I do not know why.

  I tried "repair disk" in the start menu F12 and it will not work.

  Does anyone know an alternative solution for fixing windows disk repair?

  Anyone know why they would stop work?

  I too, have a mysterious GLOW RED on my screen and do not know if this is related to repair disk does not?

  It is originally the screen system 'black '.  My main screen simply vanishes in the dark and I have to restart the computer and go through everything new; checked the Direct X (up to date) and running hard drive Diagnostics, but the diagnosis breaks down due to the error of hard disk (disk repair-related?)  What is the 'RED' light on my screen?

  Thank you!!! for any input or advice!

  
  

  Hi Nansye,

  Until solve us the problem we need more information about the problem you are experiencing.

  • What is the exact error message you receive on repair disk?
  • Since when are you facing this problem?
  • You did changes to the computer before this problem started?
  • Are you able to boot to the desktop?
  • You have a Windows Vista installation DVD?

  In the monitor that you receive the red glow due to various reasons like failure to display drivers, hardware problem or if there is any what interference of electronic gadgets.

  I suggest you update to download display drivers the latest drivers on computer manufacturers site and check if it helps to solve the problem of the red light on the screen.

  You can access the link below and follow the steps to update the drivers to display on your computer and check if it helps.

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Make sure that you do not have other electronic items kept around the screen and try to keep few away from the computer.

  If the update of the pilots is not enough, you can contact the computer manufacturer to check if there are problems with the material of the monitor and if it needs to be replaced.

  You can also run the memory diagnostic tool on your computer and check if it helps. Access the link below and follow the steps to run the tool from WinRE Windows Memory Diagnostic.

  http://Windows.Microsoft.com/en-us/Windows-Vista/how-do-I-know-if-my-computer-has-a-memory-problem 

  Postbacks with the required information.

  Thank you and best regards,

   

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Could not stop or start the DB

  Hello Experts,
  I have stutdown the oracle instance, finish the process before I got out of the command line. After that if I try to connect to the Database, I get the following error. Please help me.
  
  
  
  C:\Documents and Settings\gkalanid > sqlplus/nolog
  
  SQL * more: Release 10.2.0.1.0 - Production on sea 1 APR 17:40:07 2009
  
  Copyright (c) 1982, 2005, Oracle. All rights reserved.
  
  SQL > conn sys/oracle as a sysdba
  Connect to an instance is idle.
  SQL > startup
  ORA-10997: another start/stop operation this instance InProgress
  ORA-09968: cannot lock file
  SQL > shutdown immediate
  ORA-24324: service handle not initialized
  ORA-24323: value not allowed
  ORA-01090: shutdown in progress - connection is not permitted
  SQL >
  
  Published by: knidhi on April 1st, 2009 17:46
  
  Published by: knidhi on April 2, 2009 11:22

  Try restarting the service db in respect of services.
  And then if db does not automatically make
  sqlplus "virtue sysdba".
  startup

• Right button on the touchpad does not and cannot change the setting of what happens when the laptop is closed

  I own a HP Pavilion, under Windows Vista Home Premium, with 2-way ALPS Touchpad, I updated the touchpad driver and tried to change the options of the right button but nothing has helped.    Also, how can I change the settings for when I close my lap top

  Try the right key when it is started in safe mode or with a clean bootor maybe when logged in as a different user.

  Change the cover closing the settings by going to control panel-> Power Options-> choose closing the cover.

• LOG_ARCHIVE_DEST_2 parameter error and cannot start the primary database

  Hello
  I was getting errors in my RMAN backup script. I took a glance on the database settings. Looks like I made a mistake when I was in the LOG_ARCHIVE_DEST_2 setting in the standby database. Instead of putting on the eve I put it in the name of the primary instance. I also noticed that the LOG_ARCHIVE_DEST_2 setting has been changed in the primary database where I put it first. I guess he's changed when I changed the sleep setting. I have two questions:
  
  (1) can the parameter LOG_ARCHIVE_DEST_2 be changes for the correct setting now that I set it wrong. The reason why I ask is because when I tried to change by using the following ALTER SYSTEM command I got an error saying something about conflicting attributes. I guess it's because the name of the primary instance has been upgraded with the DB_UNIQUE_NAME instead of the name of the standby instance. If I could change the LOG_ARCHIVE_DEST_2 setting to sleep first then maybe I can change the primary to the correct setting? Please provide markets.
  
  ALTER SYSTEM SET LOG_ARCHIVE_DEST_2 ='SERVICE = < DB PRIMARY > ASYNC VALID_FOR =(ONLINE_LOGFILES,PRIMARY_ROLE) DB_UNIQUE_NAME = < PRIMARY_INSTANCE > '
  
  (2) the second question is you can start a database using a spfile? (I use ASM and Data Guard) I ask because while I was connected to the primary database I executed the following command:
  
  ALTER SYSTEM SET LOG_ARCHIVE_DEST_2 = 'SERVICE = < PRIMARY_INSTANCE > ASYNC VALID_FOR =(ONLINE_LOGFILES,PRIMARY_ROLE) DB_UNIQUE_NAME = < PRIMARY_INSTANCE >' scope = spfile;
  
  I then stop the database and try to start but it won't start because it says to conflicting attributes. I don't create a pfile from spfile file before you shut down the database. (I'm bad). How can I change the setting for the primary database to start over. (The PFILE file is different in ASM. There are sub + DATA but has only a single line indicating where is the location of the SPFILE) I need to run the following RMAN RESTORE CONTROLFILE FROM backup AUTOMATIC;
  
  Please help as it is a production environment that was supposed to be delivered only yesterday.
  
  Any help will be greatly appreciated!
  
  Thanks in advance.
  
  J

  I always use it. So my answer is Yes.

  Please consider several of the responses of CKPT marking "useful".

  He works very hard in the forum and didn't work great!

  I call it "SuperStar."

  Best regards

  mseberg

• I have an old notebook compal hel80c and cannot start the webcam it says dirvers do work properly, no icon or abilty to just start webcam

  I can't start my web cam drivers installed, it is a Compal Hel80c notebook

  Hello DarrenMorrow,

  Most OEM ship an application that works with the webcam.

  Compaq/HP would be better able to educate you on this.

  In addition, Windows Live Messenger has a video component.

  Best regards

  Matthew_Ha

• An installation support file could not be installed. The system cannot find the specified file

  I'm trying to get rid of some programs on my Windows xp, but the following alert continue to flock to the top: an installation support file could not be installed. The system cannot find the specified file

  Hello

  • What programs you try to uninstall?

  You can check this link:

  Problems installing and uninstalling programs on Windows computers

  http://support.Microsoft.com/kb/2438651

• Registration for the web function has stopped working in my copy of photoshop elements 12.  I get this message "the operation could not be completed.  The system cannot find the path specified"reset preferences was not fixed.

  Registration for the web function has stopped working in my copy of photoshop elements 12.  I get this message "the operation could not be completed.  The system cannot find the path specified"reset preferences was not fixed.

  My os is windows 7.  elements of 12 worked fine for several months and then save for web stopped working

• "Error 1402.Could not open key" during the installation of Adobe and HP update. Updates failed and earlier of the software cannot be put back in place because permission to modify the key is denied.

  • Issue: Failed to update and previous software may not be returned to or re-installed. Problem programs include Adobe Reader and scan and editor for my HP C4180 all-in-1 photo printer.
  • (For example) error messages:
    Error 1402.Could not open key:
    UNKNOWN\Components\1FA18F797...
    Check that you have sufficient access to that key, or contact your support...
  • No recent changes, with the exception of updates failed and normal widows.
  • I thought bad updates from HP and Adobe has caused the problem, so I uninstalled and tried to re - install the software several times, hoping a release update would solve the problem.  Impossible software returned to or re-installed, so I bought try 'PDF Converter 6' to to access PDF files. This program could not be installed for the same reason.

  The Windows 7 FAQ has reported that Windows 7 could be reinstalled everything keeping the settings. The same can be done with Vista? If not, is there a safe way to delete these keys, so the software can be installed/re-installed without having to make a facility 'clean '?

  Thank you.

  Hi misterDormie,

  This problem may occur if the permissions to a specific key in the Windows registry has been denied because the registry is corrupted or due to registry permissions

  I suggest you try the following steps:

  Step 1: Check with a different user profile

  If you do not have a different user account, you will need to create a (see link below).  If everything works fine with a different user profile, you can infer that the user profile is damaged, click on the link to find out how to solve this problem.

  Create-a-user account

  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

  Difficulty of a corrupted user profile

  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

  If the problem persists,

  Step 2: Run a scan online for any threat and try to correct

  http://OneCare.live.com/site/en-us/Center/cleanup.htm

   

  You can follow the steps mentioned in the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistasecurity/thread/ba80504b-61f1-4D71-960f-b561798b7b42

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Download this message when I try to run Lightroom. Point procedure entry AgTransitCargo_pushTransitCargo could not be found in the AgKernel.dll dynamic link library - system: windows 7 64 bit is no error in the log file

  Download this message when I try to run Lightroom. The procedure entry point AgTransitCargo_pushTransitCargo could not be found in the AgKernel.dll dynamic link library

  system: windows 7 64-bit

  There is no error in the log file.

  no error in scannow at the command prompt.

  

  Hi Michela,

  Lightroom makes a call the the AGkernel.dll file, but the file isn't sure what to do because it can't find the line of code within himself to answer. This can happen for several reasons, that fall within these two broad categories: AGkernel.dll is damaged and must be repaired or AGKernel.dll version is incorrect and should be updated to the correct version.

  Here are some things you can do to fix the file:

  -Record again with Windows AGKernel.dll: https://support.microsoft.com/en-us/kb/249873

  -Windows repair: https://support.microsoft.com/en-us/kb/929833

  -Install all the updates that are available for Windows: Windows Installer updates

  -Uninstall and reinstall Lightroom

  Kind regards

  Tanuj