Recommendation and cisco BE6K VM Placement Design

Similar Questions

• LAN-to-LAN tunnel between VPN 3000 and Cisco 1721

  Hello

  I have a current LAN-to-LAN tunnel configuration between VPN 3000 (3.6) and Cisco 1721 (12.2 (11) T).

  When I use the encryption = authentication and Des-56 = ESP\MD5\HMAC-128 for the IPSec Security Association, everything works fine.

  However, I would like to Turn off encryption for some time getting the speed improvements, so I changed

  Encryption = null esp (in 1721) and to "null" in VPN-3000.

  Now the tunnel is setup but I can spend only ICMP traffic. When I pass the traffic UDP\TCP the message below appears the Cisco 1721

  % C1700_EM-1-ERROR: error in packet-rx: pad size error, id 75, hen offset 0

  Has anyone seen this behavior?

  All those put in place an IPSec Tunnel with only the ESP authentication and NO encryption between VPN-3000 and Cisco 1721?

  Thanx------Naman

  Naman,

  Disable you the vpn Accelerator? "no accel crypto engine. Sure that you can't do with a null module vpn.

  Kurtis Durrett

• NCS and Cisco Security Manager 4.2 servers

  Hi all

  I spec'ing on two new servers; one is for a box of first NCS and other area of Cisco Security Manager 4.2. I have decided to go with the range servers Cisco UCS, but am a little unsure of something on the said recommended in the datasheet for the AC.

  The NCS data sheet

  http://www.Cisco.com/en/us/prod/collateral/wireless/ps5755/ps11682/ps11686/ps11688/data_sheet_c78-650051.PDF

  ... reads as follows:

  ******************************

  If the first Cisco NCS deployment as a virtual appliance on a server provided by the customer, one of the following versions

  VMware ESX or ESXi can be used:

  Version of VMWare ESX or VMWare ESXi 4.1

  ******************************

  This means that the NCS software MUST be be virtualized, or can it be installed and simply turn on something like Windows Server 2008? If Yes, through a serious disk image?

  Secondly,.

  the two servers are running RAID arrays and I was wondering what are your views on the execution of any (OS, Cisco software, records and other data) set on the RAID array, or the OS and Cisco software on a separate boot disk and store data only on the RAID?

  I see no reason why it would not run together on the RAID, but I'm curious to know what you think about it.

  In addition, we are upgrading our WCS courses and I was wondering if some kind of migration is necessary or can we just install fresh NCS on the server and configure it accordingly.

  See you soon,.

  -Dave

  Dave,

  For the first part, the NCS works only as a virtual machine.  You can buy the device hardened to it, but it's still a virtual machine, NCS is presented as a .ova.

  Regarding separate them, with NCS I don't think you'll be able to.

  Steve

• I got a Apple Watch yesterday and since put in place and paired him and everything, but now I can not unlock it or look at anything on the watch because it won't let me.  Any ideas as to what is wrong or what I am doing wrong?

  I got a Apple Watch yesterday and since put in place and paired him and everything, but now I can not unlock it or look at anything on the watch because it won't let me.  Any ideas as to what is wrong or what I am doing wrong?

  Hello

  If you have not already done so, it could be that you want to configure your watch with these settings:

  -On your iPhone, in the application of Eve, go to: My Watch (tab) > General > detection of wrist - it lights up.

  -On your iPhone, in the application of Eve, go to: Watch My > password > code turn on (choose a password Simple or more complex).

  -Also on the password settings screen, select Unlock with iPhone.

  After putting on your wrist, your watch don't unlock then after whatever you do first: unlock your watch manually (by entering the access code) or unlock your iPhone.

  Then, it will remain unlocked (including when the screen is idle) until you remove it from your wrist. When you remove your watch, it locks automatically.

  More information:

  https://help.Apple.com/watch/#/apd748b87e2a

• I recently updated my iPhone to iOS 9.3 6s and now my data and wifi are in place. Now I can't open the apps and send messages with data and barely on the wifi. I've tried everything, and it still does not work.

  I updated my iPhone to iOS 9.3 6s today and now my data and wifi are in place. Whenever I try to open an app or send text messages with data it does not at all. And with wifi, it just works. I tried just like turn roaming off and off and other lte but nothing seems to work at all. Can someone please?

  I have this same problem too, it really gets me upset

• I have a reconditioned Ipad4 64 GB and me put in place today, but it keeps going blank and then showing just the Apple. Have tried to quit, but does nothing:(delesde idées)

  I bought an iPad 4 64 GB with 4 d and have put in place today, but the cry keeps losing information and goes blank. When he decides to turn back on an Apple appears but then nothing? Did have to operate for an hour today. Not the owner of an iPad happy that I have improved my original iPad to do this. Help, please

  Where the iPad was purchased at?

• After a microsoft error message, my laptop keyboard has sudenly has started to misbehave - characters are two-way and in case added places after the original character. Clues?

  After a microsoft error message, my laptop keyboard has sudenly has started to misbehave - characters are two-way and in case added places after the original character. Clues?

  Care to be more detailed?  What version of Windows?  What is the brand and model of the laptop?  How old was he?  Have you contacted the provider support?  What has changed on your PC between when it was last and now?

• (KB972145) Recommended (KB2563894) IMPORTANT (KB968930) recommended and updated for (KB968930) everything has failed

  (KB972145) Recommended (KB2563894) IMPORTANT (KB968930) recommended and updated for (KB968930) everything has failed.

  I tried for days now to download these updates, but I did not, even in SafeMode with networking, I can't get Windows update to try to install?

  I tried a few solutions of Microsoft, but I can't like Regedit HKEY_LOCAL_MACHINE thereupon, after export the keys, that I didn't see any (PendingXmlIdentifier) and so on, so I can't go any further, I got arrested and decide to ask for help.

  If you can help me, it would be great!

  Hello

  ·          What is the error code that you receive when the update fails?

  ·          What are the other steps you've tried?

  Method 1: Reset windows update and install the updates.

  You can read the following article to reset the Windows Update components and see if it helps.

  How to reset the Windows Update components?

• How to tell the difference between recommended, and optional updates long after they have installed bene?

  I have a Vistaprogram of the window running on my Toshiba laptop.

  In the past, I've confirmed that optional udates be installed. Please help: now I want to uninstall optional updates because my computer is slow.  How to tell the difference between recommended, and optional updates long after they have installed bene?

  Hey monkey 44,

  I suggest you view the history in Windows Update:

  http://Windows.Microsoft.com/en-us/Windows-Vista/see-which-Windows-updates-are-installed

  Those listed as recommended is technically optional.

  Before you delete updates the computer, I suggest you try the steps from the following link to improve performance and check if that helps:

  http://Windows.Microsoft.com/en-us/Windows-Vista/ways-to-improve-your-computers-performance

  I hope this helps.

• LACP hash between N3048 and CISCO SG300/SG200 + question Twinax attach direct cable

  Hello

  In my network I have deployed two new N3048 with 2 transceivers SPF + and SPF module back + as core switches are connected to other 3 switches from edge of N2048 using optical fiber and I reused my previous CISCO SG300 and SG200 goes to serve the other two boxes of my campus via the spine in copper.

  I have 4 copper cable which starts from the hub of the SG300 network and 2 the SG200 brass. I set up to have a redundant connection using 2 + 2 with SG300 and 1 + 1 with SG200 RSTP.

  So for the SG300 I re LAG + LACP to have two channels of the N3048s port, but now that a single cable is connected because I don't know what kind of LACP hash mode should I put on N3048 to have a compatible hash between Dell and Cisco switches.

  My N3048 have mode 7 (Advanced hash) as default but I guess that cisco models do not understand... so, what mode is the best for LACP work perfectly with small business cisco switches?

  I also received my twinax cables to connect my two N3048 via SPF + back modules... conhot can I plug the cables into the slots SPF + (already mounted) without turning off my basic switches?

  Thank you!

  See you soon

  Cables can be connected/disconnected, but I don't know if the real module SFP + for the rear of the N3000 is hot plug.

• Unable to connect to network WPA2 with Windows 7 64-bit (Intel 4965 and Cisco WUSB600N)

  Connect to a WPA2 network seems to be a fairly common problem.  Again, I can't be able to find a solution.

  OS: Windows 7 Ultimate 64-bit

  Wireless adapter (s): Intel 4965AGN (integrated into Dell XPSM1330) and Cisco/Linksys WUSB600N

  Drivers: latest windows 7 64 bit drivers from the two websites of companies.  Intel (v12.4.1.4), Linksys (3.0.10.0)

  Network properties: WPA2 enterprise, encryption of the ACS, authentication EAP - P, several types of routers around the world

  History: has been able to use the same laptop with Vista32 on this network without any problem

  I can not connect to networks non - WPA WPA networks simply not.

  When you try to connect to my companies WPA2 network (at any of our locations around the world).

  Method #1:

  1. Select "Other network" in the list of network
  2. Enter the SSID of the network
  3. Windows could not connect to the SSID
  Method #2
  1. Open network and sharing Center
  2. Select set up a new connection or network
  3. Select manually connect to a wireless network
  4. Select one of my adapters
  5. Enter the SSID, as WPA2-Enterprise security type, type of encryption like AES, check the boxes to connect automatically and connect even if the network is not broadcasting
  6. An unexpected error has occurred

  Method #3: Try to trick windows

  1. Open network and sharing Center
  2. Select set up a new connection or network
  3. Select manually connect to a wireless network
  4. Select one of my adapters
  5. Enter the SSID but select an open network
  6. Adds the network
  7. Then try to change properties
  8. WPA2-Enterprise security type
  9. Set to AES encryption type
  10. "Choose a network authentication method:" drop-down menu is empty!
  11. Windows has encountered an error saving the wireless profile.  Specific error: the profile has an invalid length field.

  I'm pretty desperate for a solution.

  Kind regards

  John

  There are a few people with Win7 x 64 that cannot connect to WPA2 P/EAP Corporate/business networks and no solution?

  Come on, guys, it's the microsoft answers site! someone give me something! I have two asus laptops, both with network cards Intel having this problem on two networks separate enterprise (school).

  Edit:

  RESOLVED:

  Here's the thread of the resolution:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/unable-to-connect-to-company-wireless-network/3bcd12b1-A0D8-4357-bded-07da96259920?page=3

  The problem occurs when you perform a Wizard for easy transfer to a computer that was Symantec Endpoint Protection installed to one without him.

  Answer, copypasted:

  Inspect the key mentioned above - that is of HKLM\System\CurrentControlSet\services\RasMan\PPP\EAP.

  In each of the number keys look something like ConfigPathBackup and its corresponding ConfigPath - there are a number of them.

  For each, I deleted the original key (e.g., ConfigPath) and restored the original by renaming ConfigPathBackup to ConfigPath

  For each of them, the State is now restored to her pre State Symantec - each key pointed to a Symantec location that is no longer present and by restoring the path key backs up everything was fine

• This version of Cisco Adaptive Security Appliance Software Version 9.6 (1) 5 is affected by Cisco Adaptive Security Appliance SNMP Remote Code execution vulnerability and Cisco Adaptive Security Appliance CLI Remote Code execution vulnerability of

  This version of Cisco Adaptive Security Appliance Software Version 9.6 (1) 5 is affected by Cisco Adaptive Security Appliance SNMP Remote Code execution vulnerability and Cisco Adaptive Security Appliance CLI Remote Code execution vulnerability of

  Hi vrian_colaba,

  You can take a look at cisco's Advisory here:

  https://Tools.Cisco.com/Security/Center/content/CiscoSecurityAdvisory/CI...

  Fixed versions

  Cisco ASA Major Release	First version fixed
  7.2	Affected; migrate to 9.1.7(9) or later
  8.0	Affected; migrate to 9.1.7(9) or later
  8.1	Affected; migrate to 9.1.7(9) or later
  8.2	Affected; migrate to 9.1.7(9) or later
  8.3	Affected; migrate to 9.1.7(9) or later
  8.4	Affected; migrate to 9.1.7(9) or later
  8.5	Affected; migrate to 9.1.7(9) or later
  8.6	Affected; migrate to 9.1.7(9) or later
  8.7	Affected; migrate to 9.1.7(9) or later
  9.0	9.0.4 (40)
  9.1	9.1.7(9)
  9.2	9.2.4 (14)
  9.3	9.3.3 (10)
  9.4	9.4.3(8) ETA 26/08/2016
  9.5	9.5 (3) ETA 30/08/2016
  9.6 (DFT)	9.6.1 (11) / 6.0.1(2) FTD
  9.6 (ASA)	9.6.2

  5 9.6 (1) is not part of the fixed versions, this means that is assigned for the SNMP Remote Code execution vulnerability.

  Cisco Adaptive Security Appliance CLI Remote Code vulnerability to run you can also take a look at cisco's Advisory here:

  https://Tools.Cisco.com/Security/Center/content/CiscoSecurityAdvisory/CI...

  Fixed versions

  The following table shows the first software versions that include fixes for this vulnerability (9.6 is not affected)

  Cisco ASA Major Release	First version fixed
  7.2	Affected, migrate to 8.4 (3) or later
  8.0	Affected, migrate to 8.4 (3) or later
  8.1	Affected, migrate to 8.4 (3) or later
  8.2	Affected, migrate to 8.4 (3) or later
  8.3	Affected, migrate to 8.4 (3) or later
  8.4	8.4 (3)
  8.5	Affected, migrate to 9.0 (1) or later version
  8.6	Affected, migrate to 9.0 (1) or later version
  8.7	Affected, migrate to 9.0 (1) or later version
  9.0	9.0 (1)
  9.1	Not affected
  9.2	Not affected
  9.3	Not affected
  9.4	Not affected
  9.5	Not affected
  9.6	Not affected

  Hope this info helps!

  Note If you help!

  -JP-

• HP J4853A and Cisco SFP Module 100BASE-FX

  Hi all!

  HP J4853A and Cisco SFP Module modules 100BASE-FX is not compatible?

  Thank you!

  Both are 100Base FX for at layer 1, they are interoperable.

  Higher tier features will not be handled on one platform or another.

• The ACE IPS Cisco and Cisco ASA AIP - SSM (IPS)

  Is there a difference between the features offered by the Cisco ACE IPS and Cisco ASA AIP - SSM (IPS) devices?

  Can we do without Cisco ASA AIP - SSM (IPS) of 'only' configuration/implementation Cisco ACE IPS.

  Cisco AVS/ACE emphasis on commissioning and to secure web-based applications. IP addresses do not focus on just the web applications and trying to get the multiple layers of the OSI stack. Consider the IPS as a general practitioner and the ACE/AVS as an eye surgeon, or something :)

  Here is the response from Cisco itself:

  http://www.Cisco.com/en/us/prod/collateral/modules/ps2706/ps6906/prod_qas0900aecd8045867c_ps6492_Products_Q_and_A_Item.html

  Q: how is Cisco AVS Firewall application differs from an intrusion prevention system (IPS)?

  A. IPSs are solid solutions of protection against targeted attacks of known vulnerabilities in major platforms such as Windows, Solaris, Apache or Microsoft Internet Information Services (IIS). Cisco AVS excels to protect against targeted attacks Web sites or enterprise applications. These applications can be built custom internal applications or software vendor. Signatures and security patches are generally not available for these types of applications, and building these security levels in each application, it would be almost impossible.

  Q: how is Cisco AVS Firewall application differs by a network firewall?

  A. The Cisco AVS 3120 and Firewall network such as the Firewall of Cisco PIX® and Cisco ASA 5500 Series Adaptive Security appliances are complementary products. The application Cisco AVS Firewall secures Web applications; excellent network in the network security firewall. and the Cisco AVS provides defense in depth for Web applications.

  Firewall network apply policy networks, IP addresses and ports; they have a wide range of application for many different protocols layer features. The firewall can and will be deployed in many locations, including the edge, edge of the enterprise network, branch, etc. Cisco AVS imposed the policy on data HTTP as URL, headers and parameters. Cisco AVS is deployed in the data center in front of Web applications

  Concerning

  Farrukh

• Difference between Csico and Cisco Unity Connection unit

  What are the main differences between Cisco Unity and Cisco Unity Connection (version 7)

  as: 1. in Cisco Unity servers are active - failover Mode and about unity, the servers are in active-active mode

  2 Cisco Unity, knows about unity and unified messaging, integrated messaging

  What is the major difference between Unified Messaging and integrated messaging?

  Please provide some points of difference between the two...

  This may well be true today, but the gap could soon close... otherwise disappear.  Cisco is currently in EFT (field-tested at the beginning) or testing "beta" for the connection of the Unit 8.5 (1), which aims to add features of Unified Messaging Unit connection using WebDav for Exchange 2003 and Exchange Web Services (EWS) for Exchange 2007/2010.  Just a nugget to think when you consider the timing of your client to install and what platform would be best suited to most environments.  Take a look at this blog for more information/thoughts:

  http://www.netcraftsmen.NET/resources/blogs/unity-connection-with-Unified-Messaging-where-will-unity-fit-in.html?blogger=David+Hailey

  Hailey

  Please note the useful messages!