(Redirected) MONITOR WHITE

Similar Questions

• cDAQ 9133 12 "MONITOR WHITE

  cDAQ 9133 race built into windows 7 and a monitor 12 "NOR connected to monitor port is empty after coming out of sleep mode. cDAQ 9133 State seeing a flashing yellow, press reset button, indicator light turns off, monitor indicates reboot and then turns off. OR 12 "monitor power LED blinks green. Press the button has no effect. Monitor remains blank. Must be able to cDAQ turned off, and then to restart windows and monitor to display normally.

  Currently, there is no update of the BIOS for the cDAQ-9133.

  The timer that is documented in the section of the Menu system of the TSM-101 x Series manual is a little misleading: it means actually how long the screen display remains visible after the last button an is pressed.  As you found with your test during the night, monitor screen saver and standby modes depend on the display of the operating system configuration.

  The behavior you have described - the impossibility of recovering the display when power off monitor and turn it back on - is a known issue that is currently under review.  For now, the recommended solution is to configure the display to be always active, just as you did.

• HP G42-415DX: in a Setup dual monitor, perhaps armored secondary monitor white screen?

  I have a Setup dual monitor, where the laptop is tied to a 2nd monitor (TV) via HDMI. I mainly use the 2nd monitor. Can I empty the 1st monitor (laptop screen) screen, yet still use the 2nd monitor with lid open to access the keyboard?

  (I noticed with parameters changed in the Panel of Win7, I can close the lid without cutting [sleep, Hibernate or shutdown] computer and had to lower the monitor display 2nd to adapt to the screen.) But to use the keyboard, open the lid of the portable computer, which involved the 1st screen)

  Thank you

  Hi Kalad,

  I think the same as you do sometimes, especially when I watch a movie and you want that it will display on the bigger screen and the simultaneouly have the laptop screen is off.

  As you need to use the keyboard of the laptop and want the second poster only, which suggests to select the "Projector" only option in the pop-up menu by pressing the Fn + F4 key.

  & to come back again having two screens or single screen press Fn Key & F4 on your keyboard and select "Extend" or 'Unplug the projector' options respectively.

  I am an employee of HP.

  Kind regards
  Mundutha

  Make it easier for others to find solutions, marking my answer "Accept as Solution" if it solves your problem.

  Click the "Thumbs up" button to the lower right side of my post to say thank you! ***.

• (Redirected) Monitor Dell [E2310H] no auto do setting

  I can't press the auto adjust, I think that the new software need to screen, I tried to reset the default factory, but there is no solution

  

  Best of this post in the Forum of monitors, here:

  http://en.community.Dell.com/support-forums/peripherals/f/3529.aspx

  Bev.

• (Redirected) Monitor DELL U2412M - light problems

  Hello

  I just bought a DELL U2412M monitor, but have problems with its brightness settings. I found extremely bright, can't spend too much time in front of him without having headaches, at the present time, this monitor is useless for me. If I decrease the brightness of the Panel, it helps a little, but only if the brightness is of ~ 10, which is too low to produce a screen the user can enjoy. Do you have any suggestions?

  Thank you

  Norbert

  Best of this post in the Forum of monitors, here:

  http://en.community.Dell.com/support-forums/peripherals/f/3529.aspx

  Bev.

• (Redirected) Monitor S2440L

  I have owned a XPS8500 with S2440L Analyzer. Lately, my monitor has develop a foggy screen inside the screen. The foggy appear in tasks.  The fog behind the glass screen disappear after a certain time, but it has more and more often. What are the causes to happen? It's the humidity or the temperature?

  FYI, I work in an air-conditioned office with temperature set between 22 and 25 degrees celcius.

  Thank you

  Best of this post in the Forum of monitors, here:

  http://en.community.Dell.com/support-forums/peripherals/f/3529.aspx

  Bev.

• JavaEE monitor white screen of dashboard

  last night I upgraded 5.6.2 to 5.6.4 Foglight and updated Java 5.7.4 agent 5.8.1. Now, after the upgrade when I navigate to the dashboard > Custom Applications > monitor I see a blank screen. All the world is facing this problem before? Help, please...

  

  Support the case as soon as POSSIBLE!

  Golan

• Error with KbdStub.exe, monitor erased on Vista

  * original title - Kbd Stud has stopped working... this message every day... my monitor white, except for the icons at the bottom of the screen. *

  Signature of the problem:

  Problem event name: APPCRASH

  Application name: KbdStub.exe

  Application version: 1.0.9.1

  Application timestamp: 4884f1e6

  Fault Module name: C:\Windows\system32\mscoree.dll

  Fault Module Version: 6.0.6002.18005

  Timestamp of Module error: 49e0421d

  Exception code: c0000135

  Exception offset: 00000000000b8fb8

  The system version: 6.0.6002.2.2.0.768.3

  Locale ID: 1033

  Additional information 1: fa3e

  More information 2: ac0507478d1c5bd693cfc4fe3987e900

  Additional information 3: fa3e

  Additional information 4: ac0507478d1c5bd693cfc4fe3987e900

  Hi Don,

  Please see the following diagnosis:

  Start the computer in safe mode and then run boot error may be related to a program. After the clean boot, we can find the program at the origin of the problem.

  Start the computer in safe mode
  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Clean boot
  http://support.Microsoft.com/kb/929135

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• No preview in the monitor Panel

  Hi all

  When I start the reading of the images, there is no preview available in the monitor (white screen). Only arrested sequenzes appeared and the sound is played. This problem occurs regardless of the used files. When you first start it is shown failure: problems with the Intel's Graphics.But the driver is updated to the latest version. Furthermore it is not possible to change the graphics card setting, as described in the help of Pre.

  1. Select Edition > Preferences > General.
  2. Deselect the option enable GPU and playback in the playback Preferences dialog box, click OK to confirm.

  This menu is not available!

  Thanks in advance for your help and best regards,

  What model of camcorder is your coming video and what format is it?

  When you started your project, including project settings have you selected? If you have selected the right project settings for your video, you will NOT be able to see red over your clips lines when you add them to your calendar. This is the case in your project?

  Have you ensured that you have the latest version of Quicktime, by the requirements of the program? Have you passed to the site ATI or nVidia and assured that you have the latest drivers for your graphics card?

• Screen flashing horizontal lines after replacing the RAM

  Hello world

  Today, I replaced the original 2 2 GB RAM each with 2 other 4 GB each (Kingston) for better performance.

  I have a Macbook Pro end 2011 15 ", IOS 9.3.1.

  I opened the computer it vacuum cleaner very carefully, with the lowest power and then I removed the two RAM.

  I'm not new, the machine worked perfectly for 20 minutes, then the screen went black (electricity was running in it, I could see some lights on the bottom), I did close it with the button, turn it on and horizontal lines appeared.

  I turn again and nothing has changed. I replaced the new memory with the 'old' and I still have horizontal lines that cross the monitor (white, grey, black).

  Any idea of what is happening and how to fix it?

  Thank you in advance!

  That could be the problem:

  http://www.Apple.com/support/MacBookPro-videoissues/

• Lenovo T560 and Dock OneLink Pro

  I have a ThinkPad T560 (20EV000YIX) with among Pro Dock (4X10E52944) and 2 external monitors connected via DVI - I and DisplayPort ports (with VGA adapter).

  The problem is that both monitors randomly every few minutes became black and reappear after approx. 1 second.

  I've already updated the T560 and OneLink drivers but no result.

  Another question: is possible to configure the OneLink to use the video card Radeon R7 instead of integrated Intel 520HD?

  Thank you.

  Gigi

  Reconnected the old monitor whit a DP adapter-> DVI - I and the problem goes away.

  There seems to be a problem with the adapter DP-> VGA or VGA cable at this point...

• Facebook oauth login

  I'm creating an application requiring a facebook connection. I'm new to this concept of oauth. I saw bb stunts oauth library in giithub but I don't know how to. I saw the twitter oauth process which does not work in the current SDK.

  I also tried qml oauth process in webview published somewhere in the forum. But I get an error as 'success'
  SECURITY WARNING: Thank you for treating the above URL as you would your password and don't share it with anyone. »

  
  

  On the change of url redirection and white lists in the configuration advanced facebook app, it works.

• (Laptop HP-2000) White screen, external monitor works.

  (HP 2000 Notebook PC / Windows 8.1, 64-bit) Still white screen, external monitor works fine. What components could be defective? This occurred about six months ago about a week after the expiry of the one year warranty. Nonfortuitous.

  Hello

  You confirm this problem is intermittent, and now its working fine, it means that the question would be the display cable. The display cable is loose. Issue can be fixed by rebonding the display cable, if the problem persists then the display cable needs to be replaced.

  This is the only reason why I asked you in the previous post if the problem was intermittent or display changed while moving the display cover.

  This particular problem has nothing to do with the temperature.

  Kind regards

  Sumit

  I am an employee of HP

• Monitor is white empty when you try to view the video full screen on youtube.

  I have a HP w2207h screen flat monitor. When I try to view online, such as YouTube videos, full screen, the screen goes to a blank white screen. Sound works, no picture. However, when I view the same video from YouTube in Internet explore everything works fine. Is there a setting that I need to solve this problem? Would appreciate your help!

  Try disabling hardware acceleration in Flash Player.

  See the videos in Flash will not play in full screen

  Blink the window "display settings":

  • http://www.Macromedia.com/support/documentation/en/flashplayer/help/help01.html

• Satellite A300-1IL - monitor has white lines at the bottom

  Good evening

  about an hour, followed by my satellite a300 monitor has white lines at the bottom.
  I try to stop, change the resolution but i just turn on my laptop, the screen has this white line.

  It is a problem of monito'rs or videocar problem?

  Sorry for my ebglish

  Hello

  > It is a problem of monito'rs or videocar problem?
  It's easy to say; you need to connect the external monitor to the laptop and need to check if the same if possible lines on a second external display.

  If the lines were visible on the external monitor, so that the GPU fault is possible.
  Otherwise, it may be defective internal display.

  Welcome them