(Redirected) upgrade my studio 9100 with the new graphics card and a more powerful power supply

Similar Questions

• Qosmio G10 with the new graphics card and pcb - CD update tools do not work

  Hello world

  I hope you can help me. Before a few weeks, I received my Toshiba Qosmio G10 return of aid, because the laptop no longer works. So I get it back with a new graphics card and a new PCB. With my laptop I have a CD called the update tool CD and a sheet of instructions, where it says to start with this tool CD-Rom update after you have installed the Windows with the reovery CD.

  So I did, but when I know the update tool CD to put in and I start with it, the computer installs something, but after a short then it is a message that it is a different model and that I have to put a button to close Notepad. So I did it, but Windows does not start.

  Why is it so? I had done everything that has been said on the instruction sheet.

  Please help me

  Hello

  It will be interesting to find more information on this CD-Rom tool update. Are there tags Toshiba? Can you please write what is described here?

• Pavilion p6 - 2120t: Windows will not start with the new graphics card

  Installed a Zotac GT 740 profile down in my desktop PC graphics card HP Pavilion p6 - 2120t and now the PC does not start.

  HP Pavilion p6 - 2120t CTO desktop PC

  Configuration:
  Intel Pentium CPU [email protected]
  4.0 GB RAM
  Intel HD Graphics Driver version Family: 8.15.10.2291 dated 27/01/2011
  Motherboard: IPISB-CU (Carmel2) (1 open PCI Express 16 expansion slot pins)

  BIOS to Version 7.18

  Running:
  Windows 7 Home premium 64-bit w/service pack 1
  Two monitors (VGA, 1 digital port 1)

  Before installing the new graphics card, I replaced the power supply original 300w with a 400w power supply.

  For starters, I disabled the onboard graphics in Device Manager. Then, I opened the case and installed the GT-740 in the open PCI Express slot. I made sure that the card was fully engaged in the slot.

  I plugged both monitors to their connections voted on the new map.

  When I tried to boot the PC, the digital monitor displays the screen HP (the one that indicates which key support to achieve the start menu) and then frozen. No other entries of key or mouse have been accepted.

  The PC then sounds 4 short beeps (about 10 seconds between each beep) and then a long beep before turning off the signal to the screen.

  Then, I removed the new graphics card on the PC that starts then. I have reactivated the original graphics drivers and the PC then worked normally.

  Tried the above process two more times with the same results.

  I then went into the start menu to look at the BIOS. The menu of the BIOS shows two options:

  > Sources of boot UEFI

  Windows Boot Manager

  > Sources of boot legacy

  ATAP I CD/DVD player

  SATA2

  Hard drive

  SATA0

  Network controller (Realtek PXE B06 D00)

  PC using UEFI Boot Manager Windows boots normally

  I have not tried Legacy Boot Sources because I don't know which one to choose.

  I went to the HP site and looked for an update to the newest BIOS, but updating them is a rev version 7.16 while my PC shows my BIOS to version 7.18

  I know that others have had a similar problem but I have not seen a solution that works for my PC.

  Any advice would be welcome.
  Thanks for your time.

  Hello

  Your PC isn't spec'd to run Windows 7 using the Windows Boot Manager.  I expect to a UEFI-based graphics card likely to work on an HP PC that does not have a BIOS version 8.

  The below listed OEM HP, graphics cards should work in your PC using a normal non - UEFI W7 and W8 installation.

  

• Does not start with the new graphics card

  Hello. I have a P7-1058uk Pavilion Cleveland-GL8 motherboard with integrated graphics.

  I bought a new monitor that has resolution 2560 x 1440, equal the integrated graphics card can face if tried to to level with a Gigabyte GT630 card.

  When I start, I have now the chance to the blue HP screen but not more details. If I start with F10 or ESC key, I get a black screen instead. Whatever it is, I am asked to press ESC to enter in the start, but by pressing on the button has no effect and the computer just hangs. There is a cycle repeated very quiet click that sounds like the disk drive HARD trying to start then stop

  If I remove the graphics card and connect the monitor to the integrated graphics card then all's well again (but limited to the resolution 1920 x 1080).

  Perhaps foolishly, I assumed it was a problem with the residual power (300W) and not enough punch power to run the HARD drive. But who, after having upgraded to 650W it makes no difference. I also tried to download the NVidia drivers but it won't let me install because I can't get the computer to work without the graphics card and Nvidia install it because it cannot detect the hardware.

  Any ideas/help would be appreciated.

  Andrew

  You can have one of these motherboards that are not happy with NVIDIA graphics cards.

  This may sound a little weird, but it happens.

  The other possibility is that you have damaged your home x - 16 PCI Express by installing a map requiring more that the installed power supply has been able to provide.

  Kind regards

  ERICO

• Help with the new graphics card on old pc

  I have a dell dimension 3000 'ya I know sad' I would like to add a graphics card and a new soft power since the wife won't let me buy a new PC GRRRR

  I have a GeForce 6200 PCI 256 MB dcr2 it will work in this pc

  I also bought a power electric double w 480 SATAs is large enough to run the new card and the pc?

  Thank you

  You can add the 6200 PCI if you wish.  It does not require an upgrade of the power supply however.  It will work fine on your PSU 250 watts.  I have the 6200 circulating in a Dell with a 250W unit just to get the higher resolutions than the integrated graphic card has been able to provide in support of a monitor.

• Lenovo M91p desktop does not boot with the new graphics card (Blank don't screen no BIOS)

  Hi all

  I recently bought a Lenovo M91p thinkcenter Desktop as an upgrade to my old PC i3.

  Old Spec is as follows:

  • Coolermaster Thunder 600W power supply
  • Card mother Intel DH55HC
  • Processor i3
  • Graphics HIS HD Radeon 7950
  • 8 GB RAM
  • HARD DRIVE 500 GB

  I transferred my HD supply and Power 500 GB old to new Lenovo desktop and everything starts very well.

  Then I installed 2 x 2 GB extra in the Lenovo M91p (which in fact 8GB) and updated the disk of 500 GB to 1 TB.

  So my new spec is as follows:

  • Coolermaster Thunder 600W power supply
  • Card mother Lenovo Q67
  • I7 2600 3.4 Ghz CPU
  • 8 GB RAM
  • 1 to and 500 GB HARD drive

  Everything Booted fine. Then I tried to install my old graphics (HIS 7950 graphics Radeon HD card) card. I got was a blank screen, no beeps, no BIOS... Nothing.

  At first, I thought that my diet was not enough... So I tested a 750W power supply in the pc. Still nothing.

  Then I thought that the motherboards BIOS was outdated... Updated... Still nothing. I even tried to update the firmware of the graphics card. Nothing.

  The graphics card works because I tested it in my old machine and it worked 100%.

  However, I took my graphics card to my provider and he tests it on another of his pieces... Did not work there either.

  My PC BIOS is not supported for secure boot, in case anyone wants to know.

  I am out of ideas now... Anyone able to help?

  There is a white list of graphics cards that will recognize the BIOS. The 7950 HD is a map of 180w, well beyond what the power plant can provide (and case/sufficient cooling fans for) and not a single one is that Lenovo would provide support for the BIOS.

  Use the search engine above to see what cards other owners have used successfully in their M91p.

• Need help with the new graphics card

  So my trusty GTX 555 is finally dying after 4 years and 10 000 + hours so I looked in an upgrade and heard the GTX 960 would be a good upgrade for an Alienware x 51 R1. So I got a PNY GeForce GTX 960 Amazon and installed but when I turn on my system it passes to the BIOS screen and is there for about a minute and a half and it beeps every 30 seconds after the screen came. After the minute and a half or two then goes to a black screen and says the brand and model of graphics card in the upper left corner for about 5 seconds, then he sits on a black screen. I did something wrong?

  If necessary system specs:
  330W POWER SUPPLY
  Intel Core i7 2600
  8 GB RAM
  Windows 7

  Have you updated the BIOS?

• With the new graphics card failure

  I tried to put a graphics card in my desire to 700-210xt, there graphocs of the motherboard and I need the output HDMI and DVI, which he did not.  I added an ASUS silent 210.  Power on or monitor the work and the computer beeps six times.  Monitor never works, not isolation, or duplicate, even if the computer doesn't seem to not be starting.

  Remove the graphics card returns the system operation.

  Suggestions?

  Hello

  See the HP document on the following link.

  http://support.HP.com/us-en/document/c03653200

  Kind regards

  DP - K

• NO SOUND! Install the new graphics card and now I have no sound

  Tried the other recommendations.  Looks like Nvidia tood on realtek... Yet when I click on says playback devices... NO AUDIO DEVICE IS INSTALLED

  Installed a PCle Verto GeForce 210 PCI Express slot on the motherboard.

  Windows Vista Edition Home Premium

  Compaq Presario SR5000

  UPDATE-uninstalled realtek and Nvidia now appears in reading... said devices his work... but not sound.

  I have it!

  You BIOS must be changed by self on "ENABLED" in the sound section of the Advanced tab.  F10 on my pc to access the configuration of the system when the first light.

• Can I put a new graphics card and power supply in my computer.

  Hey all, I have the model P7-1459 and it is good, but I was hoping maybe give him a boost of game. But I was not able to know if she could handle what I want to do. The new graphics card would require a 450W power supply, and I do not know if this model could handle. Anyone know of a way or another? Need help.

  Joshua, you are welcome!

  I'm sorry that I misunderstood your question.  I thought that you wanted to know if the computer would process the card.

  Yes, you can upgrade the power supply (PSU).  I suggest to measure the PSU existing and comparing these measures to the one you choose.  I love OCZ and Corsair.  They will provide quality amateur with a reasonable price.  A good video card requires a clean and stable power supply.  I recommend at least 500W; 550W at 600W would be even better.  This would allow for future updates.  The computer uses only the amount of energy needed to operate the components.

  I hope this helps.

  If your problem is solved, please click "accept as a Solution.

• Don t work under El Capitan and I don't get an update/upgrade? I've used until yesterday an old MacBook pro and Lion, everything was perfect with an opening. Now, with the new element (iMac) and El Capitan, I have problems.

  Don t work under El Capitan and I don't get an update/upgrade? I've used until yesterday an old MacBook pro and Lion, everything was perfect with an opening. Now, with the new element (iMac) and El Capitan, I have problems.

  It is not possible to update the version of Aperture is 3.4.5

  What can I do?

  You can only update if you have a version of the AppStore of Aperture - if your version of Aperture appears in the history of your purchases on the App Store. Update and then reinstalling.   See this tip of the user for more details:

  Update to Aperture 3.6 after the publication of Photos

• How to maintain the availability of the data store after the upgrade to ESXi 5.1 with the new IP address and the naming convention?

  How can we maintain access to the presented LUNS and VMFS data store after we improve the ESX in ESXi with the new naming convention and the new model of IP addressing?

  My back-end SAN EMC Clariion is VNX

  Thanks in advance.

  How are the hosts connected to storage systems. With FC HBA for example, there is basically nothing you need to do since the WWN will remain the same and so LUN presentation of the zoning on the switch and storage system does not need to be reconfigured.

  André

• Pavilion p6 - 2020t: HP-Pavilion will identify the new graphics card

  Hello

  I got a HP Pavilion for a few years now and never updated my BIOS (not that I know well). I'm trying to install a new graphics (gtx 750ti) card and the computer does not recognize it. It shows the first screen, and then a black screen and a beep, then it crashes. Keyboard does not work, cannot get into the BIOS.

  I tried everythign with current BIOS, boot legacy and ensuring that the Integrated GPU is disabled, and nothing works. I also did research on food, and but it is not terrible, it should work with this graphics card (the fan even spinning).

  According to my research, the current BIOS is simply not recognize, and I need to update. My current version is: FRIEND 7.16, 05/10/2011

  I navagate through the HP website and it said that the automatic update should update the BIOS for Windows 10, and it won't let me download all drivers (although the last BIOS update was 2011). I tried to enter the FRIEND's site and download it from there and it won't even install their drivers, it says that flash is not supported (probably for Windows 10).

  If someone could give me an idea of how can I get a newer version of the BIOS for my motherboard, it would be much appreciated as I'm pretty sure that's the reason why the computer is not recognizing the new graphics card

  The risk is that the video card is one that is for a newer PC with an EFI BIOS. That's why the empty card is not recognized.

  If you use a card equipped with a switch on the virtual card allowing the use in legacy and uefi BIOS it will work with the BIOS of your PC.

  Sapphire makes video cards that have this capability. Take a look at the catalogue. What you need is a PCIE x 16 card video with switchable legacy\uefi BIOS or legacy support, but not only UEFI.

  http://www.sapphiretech.com/catapage_tech.asp?cataid=8 & lang = eng

  You cannot change the type of BIOS that your PC has in the UEFI.  It's a question of his being of a generation of diferent from the PC.

• Cannot download creative cloud because I'm in the Kenya, even though I am an American with the American credit card and the address of the credit card.

  Cannot download creative cloud because I'm in the Kenya, even though I am an American with the American credit card and the address of the credit card. I changed my region on my Adobe back account in the United States, but it won't let me download it.

  I think that the Downloader checks your IP to be sure that you are, where you say you are... so your account is based in the United States will not work for a purchase, since you are not actually in the United States

  Since this is an open forum, not Adobe support... you must contact Adobe personnel to help

  Chat/phone: Mon - Fri 05:00-19:00 (US Pacific Time)<=== note="" days="" and="">

  Don't forget to stay signed with your Adobe ID before accessing the link below

  Creative cloud support (all creative cloud customer service problems)

  http://helpx.Adobe.com/x-productkb/global/service-CCM.html

• H8 1241: problems with the new video card on h8 1241

  OK, I've seen a lot of posts on this topic, but I couldn't find anything yet. I bought this computer as a windows 7, but have just upgraded to windows 10. The stock video card HDMI port came out, so I ordered an ASUS Geforce gtx 750ti to replace.

  http://www.Amazon.com/GP/product/B00IB9P1KG?PSC=1&redirect=true&ref_=oh_aui_detailpage_o00_s00

  When I try to boot with the new card I get the blue screen that tells me to Press esc to get into the BIOS, but it is freezing it (I am not able to get into the bios).

  Currently, the only way to make changes are re - insert my old card. I can not even start without secondary card by using the on-Board (which could as a result of the changes that I made in the BIOS). Most of the solutions I've seen involved changes in version 8 of the BIOS but I can't get that. I tried to update my BIOS to the latest version for windows 7, but I don't think it worked b/c I am on windows 10 now.

  Help, please!

  Hello

  The level of your PC motherboard BIOS is not compatible with the cards NVIDIA GXT 7xx series.

  Contact ASUS to obtain redress. ASUS has maybe a video BIOS update or a different graphics card that will work in your PC.

  A NVIDIA GTX 660 new or used may be your best bet.

  Thanks for posting on the forum.