Redundancy ASA - Client to the remote access (AnyConnect or IPsec) VPN Cisco to 2 PSI

Similar Questions

• When I try to start the Remote Access Connection Manager in services.msc, the service will not start.

  Rick2425

  When I try to start the Remote Access Connection Manager in services.msc, the service will not start. I get the same error: "Windows could not start the service of connection manager on the local computer remote access: Error 1068: the dependency service or group could start."  Also, I can not restore the system to come and let me run it.

  It is a Dell PP31L, which belongs to a friend who does not connect to the internet because of these error messages.

  Hello Rick2425

  See the thread below and let me know if it helps thanks.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/error-1068-remote-access-connection-manager/b5155a8a-671e-4d11-8a99-deadc7aee8a1

• The remote access connection manager could not start. Error 2: cannot find the specified file.

  I've updated from vista to the most recent update.

  I have windows vista Home premium 32-bit.
  I want to get this matter resolved without having to reinstall as I have a few games installed it on this system.
  The modem is not the issue as other computers connect very well.
  Thanks for the help from Microsoft.
  Recently, I tried to connect to the internet but that was not possible, because no connection could be established. The remote access connection manager does not start 2 error: could not find the specified domain. the RasMan-dependent services are started, but Manager logins remote does not start.

  Hi Mundilfar,

  You can try the folliwng steps and see if it helps.

  Step 1:

  You can try to scan the file system [SFC] checker on the computer that will replace missing or corrupt files & check if the problem persists.

  For more information, you can consult the following link.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  Step 2:

  If you are always faced with the question, then you can try to give permission for the Rasman registry key and see if it helps.

  Important: The following steps show you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, follow the steps from the link below:

  Back up the registry

  a. Click Start, type regedit in the search box and press ENTER.

  b. Locate the following subkey:

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\RasMan

  c. right click on the key and click Permissions.

  d. Select Advanced, click on owner tab, click your user name, and check the 'Replace owner of subcontainers and objects', click Apply - click OK.

  e. click the user or group name that you want to work with.

  f. check allow total control. Click apply and then click OK.

  g. restart the computer and check.

  Hope this information is useful.

• After the remote access connection, network printers disconnected

  I hope someone can help me here.

  In Windows Vista, whenever I would give the remote access connection to my PC at home, my default printer (which was be a shared printer on the network out of my server) will prepare its default value.  It was boring but easily fixible.

  I've since upgraded to Windows 7 Ultimate and I'm having a related problem.  Now every time I connect remotely to my home PC, my default printer (same network shared printer - HP LJ 4000) disconnects, and it only comes back online after a reboot.

  It is a point of pain is huge for me because I usually 20 + / applications windows running at a given time and a restart takes 30 minutes out of my day to get back to where I was.

  Any help would be appreciated. Jeff Balcerzak

  http://h30434.www3.HP.com/T5/printer-all-in-one-software-and/Windows-7-C7200-C7280-offline/m-p/167672

  http://social.technet.Microsoft.com/forums/en/w7itpronetworking/thread/0cfa31d7-B44B-4241-aa31-d0ae9f0a2112

  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c00843712&tmp_track_link=ot_faqs/top_issues/en_US/c00843712/loc:8 & lc = en & dlc = en & cc = us & product = 1153481 & lang = en

• Error 1068: the dependency service or group failed to start and failed to start the remote access connection manager service.

  Original title: Windows could not start the service of connection manager on the local computer remote access

  amplifier

  Windows could not start the service of connection manager on the local computer remote access

  Error 1068: The dependency Service or group could start.

  Hi sunelchandraoli,

  1. when exactly you receive this error?

  2. you remember to make changes to the computer before this problem?

  Step 1:

  "Make sure that all the services of the dependence of the"Remote Access Connection Manager"" are launched in the list of services...

  a. Click Start, type services.msc in the box start the search.

  b. select Services from the list programs. If you are prompted for an administrator password or a confirmation, type your password or click on continue

  c. right click on the Remote Access Connection Manager service and then click Properties.

  d. under the general tab, click Manual next to startup type.

  e. under the general tab, click Start under the service status and then click OK.

  f. also check for long-term services.

  The dependency of 'Remote access connection manager' services include:

  i. secure Socket Tunneling Protocol Service

  II. telephone

  III. Plug-and-Play

  IV. Remote Procedure Call (RPC)

  c. of DCOM Server process Launcher

  VI RPC end point mapper.

  Make sure that the above services are started in the services list. If this is not the case, start all services above and check.

  Step 2:

  You can also try a system restore to a prior restore point you have been affected by the issue.

  Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  To run the system restore, you can consult the following link:

  System restore

  http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

  System Restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

  Hope this information is useful.

• VPN error 868 the name of the remote access server is not resolved

  I use Windows 7 Home Premium and you want to configure a VPN with my office network that uses the Check Point Safe@Office.  I am unable to log in and get the error that does not resolve the name of the remote access server and Windows cannot find the host using DNS name.  Any suggestions on what to try to fix the problem?  I set up the VPN connection according to the instructions of our network administrator.  We use XP in the office.

  Hello
  Welcome to the Microsoft answers site

  The question that you'd be better suited in the TechNet community. Please visit the link below to find a community that will provide the best support.
  http://social.technet.Microsoft.com/forums/en-us/ForefrontedgeVPN/threads

  It may be useful
  Thanks and greetings
  Support Microsoft-dieng
  Visit our Microsoft answers feedback Forum and let us know what you think
  http://social.answers.Microsoft.com/forums/en-us/answersfeedback/threads/

• IPSec vpn cisco asa and acs 5.1

  We have configured authentication ipsec vpn cisco asa acs 5.1:

  Here is the config in cisco vpn 5580:

  standard access list acltest allow 10.10.30.0 255.255.255.0

  RADIUS protocol AAA-server Gserver

  AAA-server host 10.1.8.10 Gserver (inside)

  Cisco key

  AAA-server host 10.1.8.11 Gserver (inside)

  Cisco key

  internal group gpTest strategy

  gpTest group policy attributes

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list acltest

  type tunnel-group test remote access

  tunnel-group test general attributes

  address localpool pool

  Group Policy - by default-gpTest

  authentication-server-group LOCAL Gserver

  authorization-server-group Gserver

  accounting-server-group Gserver

  IPSec-attributes of tunnel-group test

  pre-shared-key cisco123

  GBA, we config user group: VPN users. all VPN users in this group. ACS can visit his political profile: If the user in the 'VPN users' group, access ACS.

  When we connect from a VPN Client to the server, all users connect to success. When you see the parser in ACS journal, each user success connect also get

  error:

  22040 wrong password or invalid shared secret

  (pls see picture to attach it)

  the system still works, but I don't know why, we get the error log.

  Thanks for any help you can provide!

  Duyen

  Hello Duyen,

  I think I've narrowed the issue. When remote access VPN using RADIUS authentication we must keep in mind that authentication and authorization are included on the same package.

  Depending on your configuration, the ACS is defined as a server RADIUS (Gserver Protocol radius aaa server) and becomes the VPN Tunnel authenticated and 'authorized' on this server group:

  authentication-server-group LOCAL Gserver

  authorization-server-group Gserver

  As noted above, the RADIUS of request/response includes authentication and authorization on the same package. This seems to be a problem of incorrect configuration that we should not set up the 'permission' in the Tunnel of the group.

  Please remove the authorization under the Tunnel of Group:

  No authorization-server-group Gserver

  Please test the connection again and check the logs of the ACS. At this point there are only sucessful newspaper reported on the side of the ACS.

  Is 'Permission-server-group' LDAP permission when authenticating to a LDAP server so to retrieve the attributes of permission on the server. RAY doesn't have the command as explained above.

  I hope this helps.

  Kind regards.

• Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

  I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

  Thank you

  interface Ethernet0/0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.240

  !

  interface Ethernet0/1

  Speed 100

  full duplex

  nameif inside

  security-level 100

  IP 10.88.10.254 255.255.255.0

  !

  interface Management0/0

  Shutdown

  nameif management

  security-level 0

  no ip address

  !

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of the PAT_to_Outside_ClassA object

  10.88.0.0 subnet 255.255.0.0

  network of the PAT_to_Outside_ClassB object

  subnet 172.16.0.0 255.240.0.0

  network of the PAT_to_Outside_ClassC object

  Subnet 192.168.0.0 255.255.240.0

  network of the LocalNetwork object

  10.88.0.0 subnet 255.255.0.0

  network of the RemoteNetwork1 object

  Subnet 192.168.0.0 255.255.0.0

  network of the RemoteNetwork2 object

  172.16.10.0 subnet 255.255.255.0

  network of the RemoteNetwork3 object

  10.86.0.0 subnet 255.255.0.0

  network of the RemoteNetwork4 object

  10.250.1.0 subnet 255.255.255.0

  network of the NatExempt object

  10.88.10.0 subnet 255.255.255.0

  the Site_to_SiteVPN1 object-group network

  object-network 192.168.4.0 255.255.254.0

  object-network 172.16.10.0 255.255.255.0

  object-network 10.0.0.0 255.0.0.0

  outside_access_in deny ip extended access list a whole

  inside_access_in of access allowed any ip an extended list

  11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

  outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

  mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

  NAT static NatExempt NatExempt of the source (indoor, outdoor)

  NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

  NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

  !

  network of the PAT_to_Outside_ClassA object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassB object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassC object

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_access_in in interface outside

  inside_access_in access to the interface inside group

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  dynamic-access-policy-registration DfltAccessPolicy

  Sysopt connection timewait

  Service resetoutside

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto-map dynamic dynmap 10 set pfs

  Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

  life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

  Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

  Crypto-map dynamic dynmap 10 the value reverse-road

  card crypto mymap 1 match address outside_1_cryptomap

  card crypto mymap 1 set counterpart x.x.x.x

  card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

  card crypto mymap 86400 seconds, 1 lifetime of security association set

  map mymap 1 set security-association life crypto kilobytes 4608000

  map mymap 100-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto isakmp identity address

  Crypto isakmp nat-traversal 30

  Crypto ikev1 allow outside

  IKEv1 crypto ipsec-over-tcp port 10000

  IKEv1 crypto policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 50

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  preshared authentication

  aes-256 encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal BACKDOORVPN group policy

  BACKDOORVPN group policy attributes

  value of VPN-filter 11

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  BH.UK value by default-field

  type tunnel-group BACKDOORVPN remote access

  attributes global-tunnel-group BACKDOORVPN

  address pool Admin_Pool

  Group Policy - by default-BACKDOORVPN

  IPSec-attributes tunnel-group BACKDOORVPN

  IKEv1 pre-shared-key *.

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  Excellent.

  Evaluate the useful ticket.

  Thank you

  Rizwan James

• Crossed between the remote access client to a remote site at a Site in Tunnel

  Here's the scenario: users access remote vpn in ASA5510 with the tunneling split. The ASA has a tunnel from one site to another site. Vpn remote access users must be able to come and then go back devices on this tunnel from site to site. Is it still possible? Most of what I see on crossed is internet access when not to use the tunneling split.

  Thank you!

  You can do this job.  First of all, you should make sure that the command "permit same-security-traffic intra-interface" is configured.  You will then want to update your remote access ACL to include accessible subnets via the split tunneling L2L tunnel.  In this way, customers will receive a static route routing traffic through the tunnel for remote access.  The ACL crypto for the L2L tunnel shall include either a specific or analytical entry to the pool of the VPN client to destination subnets.  The corresponding crypto ACL on the far side of the tunnel L2L will need to be updated with a mirror reverse configuration of hub.  Finally, if you have configured on the NAT ASA, you will need to include a rule of exemption for the pool of VPN client-> remote subnet traffic flow.

• Unable to SSH/telnet through the remote access VPN to ASA interface

  Hi all - im trying to SSH/telnet to my ASA in my remote access VPN tunnel but

  can't get this to work.  what Miss me?

  remote access VPN subnet: 192.168.25.0

  LAN subnet: 192.168.1.0

  config is attached.  THX-

  Please enter the command

  Private access Managament

  and you will be able to telnet/ssh to the asa on this ip 192.168.1.253

• ASA 8.2: the license upgrade Anyconnect affect current users of IPSEC?

  Hello

  I am preparing to license upgrade of Cisco ASA 8.2 to an anyconnect essentials and mobile. Are there concerns with some users continue to use the IPSEC cisco vpn client, while others migrate to the Anyconnect? I just want if make sure that when I update the license as there is not an immediate requirment to have all users go to Anyconnect immediately. Thank you!

  AnyConnect essentials affects any - IPSEC, but it will disable the portal without SSLVPN client and don't allow the anyconnect SSLVPN client.

  This will not affect your IPSEC remote access clients.

  -Jason

• Profile Manager - failed to install the remote access profile in the domain environment & multi-Active Network Directory

  Hi all

  I am a COMPUTER administrator for a college and I am trying to fix what seems to be the last hurdle in getting the Profile Manager works correctly.

  I worked for a while now trying to get the Profile Manager capable of pushing the device and profiles for Mac in our group network environment. I was able to operate intermittently, but not often. Most of the time I'm unable to install the remote management profile.

  When you try to install the remote management profile, I give myself one of the two errors-

  The first error is:

  The Installation of the profile failed.

  The «TeleManagement (com.apple.config. » profile (Server.FQDN.mdm:GUID) "could not be installed because of an unexpected error < MDMResponseStatus:500 >

  (Obviously server.fqdn and GUID are placeholders for their actual values)

  

  The second mistake is:

  The Installation of the profile failed.

  Failed to contact the Protocol SCEP server to ""http://server.fqdn: 1640/CEP / "."

  

  The server Mac OS X 10.11.4 works

  OS X Server is version 5.1

  Client Mac is for most running 10.10.4

  Here's a quick run down on the environment and the steps I have already taken to solve the problem.

  • The network is an Active Directory with several networks multi-domain environment. I mainly work with two different networks, each associated with one of the two areas.
  • The Mac server hosting the Profile Manager is a Mac Pro. The two network cards is used, each on one of the two networks. The Mac server is joined to the domain in the primary forest.
  • I opened all the ports and IP ranges for Apple's Push Notification service for two on our firewall and tested networks between the two networks to ensure that the AFN is accessible.
  • I created a static DNS entry for the server in the DNS zone for the main domain. I also have a separate DNS zone for the DNS record for the interface on the secondary network. I also confirmed that Macs see the correct IP address of the Mac server for their network.
  • I tried to change the settings for network access for the Profile Manager. The first error seems to happen when the Profile Manager are restricted to the network the Mac client is not connected. This same error also occurs if I open Manager profile access to "all networks".
  • I have experiemented with the different certificate types. In general, I use the self-signed certificates that are generated automatically. In this scenario, I install the profile Trust first (which works seamlessly regardless of network or domain). I also tried to use a certificate for Code signing signed with our own CA to sign the profile of remote management. The same errors will occur no matter what certificates are used.
  • The second error occurs when the access profile manager is limited to the same network that is connected to the Mac client
  • I ran Wireshark captures on several client computers, as well as on the Mac server interfaces and haven't seen any traffic blocked or rejected that seemed related to the Profile Manager
  • I've deleted and rebuilt my OD master
  • I also scoured newspapers for clues Profile Manager and haven't found much
  • In addition, I have also studied the problem and error codes/etc widely and have not found a lot of useful information
  • I don't know there are any other troubleshooting steps I took as well, but I've been question bout this for awhile and I don't remember everyone.

  That's a strange thing - I had it working for Mac on the main network and the domain. However, I discovered that the Mac on the secondary network and the field was unable to download the profile of remote management. This is when I started to change the Profile Manager, access network, which eventually introduce the problem on Macs connected to the primary/field of experimentation network. Change access return settings in Profile Manager does not restore functionality for pimps who worked.

  Another thing odd in this test scenario all - Mac on the network high school/area would not install remote profile unless management I temporarily moved it to the main network (I do not untie / reassign to one the main domain on these Macs) I could get the profile of remote management to install and then pushing profiles has worked. Even more strange, it's the Mac that I had to move temporarily secondary network to the main network to allow remote management profile install only works always as long as the Profile Manager are restricted to the secondary network and 'the Mac'. However, Macs in the same room, on the same network in the same field, using the exact image even get the errors described above.

  The only thing I have not yet done is delete/reconstruction Profile Manager. I would really like to avoid this if possible. Solutions that involve something like Casper or other software integration AD for Macs are also a non-starter.

  I'm happy to elaborate if necessary. I appreciate the help.

  Okay, I think I can find the root cause.

  Before this discovery, I had completely rebuilt Profile Manager. Now, I managed by pushing the management profile remote for Mac in the two fields/networks. However, many of them still refuse to install remote management profile.

  Macs who encounter the problem are all were imaged using NetRestore using an image captured from an another similar iMac. IMac even that was used to build the image has now been reassigned in a test of Mac. I found that when you attempt to register one of the Mac who had received this image it shows already as "registered" when you go to "mydevices" on my Mac server. I also noticed that they all have the serial number of the test Mac when viewing their "register". Among the issues of Macs, I activated the lock of the device from the page "mydevices" for the so-called problematic Mac registered (showing the serial number of the iMac used to create the image) and it locked the iMac used to create the image - not the Mac issue.

  This tells me that the CID (or Mac equivalent) is set on the Mac CID used to create the image for all of the Mac said image was deployed to. If it's a Windows box I have a sysprep prior to deployment or could perform a rearm after the fact. I am unaware of how to perform similar functions in OS X.

  I tested also since on some Macs that do not have this image, and they are able to register and install the profile of Managing remotely with success.

  If anyone has any suggestions on how to reset the CID (the computer ID) under OS X, I'd appreciate it. Thank you.

• Implementation of the remote access VPN IPSec using SRI 2801

  Hello

  I tried to set up a VPN for remote access using 2801 SRI. I've been able to establish my house vpn tunnel using the DSL (behind a NAT) connection, give it SRI the IP address that is in the ip pool I configured on safety. The problem I have right now is that it does not reach the company LAN network.

  DIAGRAM:

  MODEM PC (VPN CLIENT) ADSL - ROUTER SOHO - INTERNET - ISR2801 - LAN---(10.10.0.27&192.168.0.9) COMPANY

  PC: 172.16.10.122

  SOHO ROUTER LAN IP: 172.16.10.254

  SOHO ROUTER WAN IP: Dynamically assigned by ISP

  ISR2801 WAN IP: x.x.x.5/224

  IP LAN ISR2801: 10.10.0.50/24

  The CORPORATE LAN subnet: 10.10.0.0/24 and 192.168.0.9/24

  2801 SRI CONFIGURATION:

  AAA new-model

  !

  !

  connection of AAA NOCAUTHEN group local RADIUS authentication

  local NOCAUTHOR AAA authorization network

  !

  !

  IP domain name xxxxx.com

  !

  !

  !

  username root password 7 120B551806095F01386A

  !

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto 5 40 keepalive

  ISAKMP crypto nat keepalive 20

  !

  Configuration group isakmp crypto-GROUP NOC client

  touch [email protected]/ * /! ~ $ 9876 qwerty

  DNS 192.168.0.9

  192.168.0.9 victories

  xxxxx.com field

  LWOP-pool

  include-local-lan

  netmask 255.255.255.0

  !

  !

  Crypto ipsec transform-set AC - SET esp-3des esp-sha-hmac

  !

  dynamic-map crypto NOC-DYNAMICMAP 10

  transformation-LWOP-SET game

  !

  !

  list of crypto AC-customer card NOCAUTHEN card authentication

  list of crypto isakmp NOCAUTHOR AC-card card authorization

  crypto map CNP-map client configuration address respond

  Crypto map AC - map 10-isakmp dynamic ipsec AC-DYNAMICMAP

  !

  !

  !

  !

  interface FastEthernet0/0

  IP address x.x.x.5 255.255.255.224

  Speed 100

  full-duplex

  card crypto AC-map

  !

  interface FastEthernet0/1

  IP 10.10.0.50 255.255.255.0

  Speed 100

  full-duplex

  !

  local IP NOC-POOL 192.168.250.101 pool 192.168.250.110

  IP route 0.0.0.0 0.0.0.0 XXX1

  IP route 10.10.0.0 255.255.255.0 10.10.0.10

  IP route 172.16.10.0 255.255.255.0 FastEthernet0/0

  Route IP 192.168.0.0 255.255.255.0 10.10.0.10

  IP route 192.168.250.0 255.255.255.0 FastEthernet0/0

  !

  I have attached a few screenshots. My goal here is to have access to my LAN to the company (10.10.0.0/24 and 192.168.0.9/24). I don't know what is missing here.

  No, we don't need not NAT. wanted to confirm if NAT could cause this problem.

  The config looks good. Can you ping routers ip internal interface the client LAN once it connects?

  Are correct, w.r.t. transatlantic lines reaching pool behind router VPN?

  If so, I would like to take a look at the exits following when a client is connected.

  See the crypto eli

  ISAKMP crypto to show his

  Crypto ipsec to show his

  SPSP

• Make the remote web server accessible via VPN Site to website

  We have two test sites that are connected by a tunnel IPSEC VPN site-to-site (hosted on a SAA each site) over the Internet. We are trying to set up an environment to test two web applications running side by side. Two web servers are running on the Site of Test 1. We don't have the same public IP available at each site.

  To address the public site 1 unique IP address restriction, we try to install ACL and NAT rules to have 2 Site accept traffic from the internet and send it on the site to the other tunnel. So 1 Web server would accept the ASA 1 internet traffic and Web Server 2 accept traffic from ASA 2 to the other site. Here's a network diagram:

  

  We have difficulties to get this configuration works correctly. Please note that the network 192.168.3.0/24 clients are able to access the servers Web1 and Web2. This question seems to be due to our NAT configuration. This is the type of error, we see on the two firewalls:

  Asymmetrical NAT rules matched for flows forward and backward; Connection for tcp src outside:4.4.4.4/443 dst outside:192.168.1.10/443 refused due to path failure reverse that of NAT

  Our situation seems similar to this post: https://supportforums.cisco.com/thread/2242230

  Any help would be appreciated.

  Hello

  What Karsten said above is true. While it is possible and works, it also means that the configuration is a little more complex to manage. I have done no such features in a real-life network environment and have always used additional public IP addresses on the local site when a server is hosted.

  If you want to continue to move forward with this so here's a few points to consider and the configurations that you need.

  First off it seems to me that the other server will be organized by the local Site 1 so a simple static PAT (Port Forward) must manage the Site 1.

  network of the WEB-HTTP object

  host 192.168.1.10

  NAT (inside, outside) interface static tcp 443 443 service

  And if you need TCP/80 also then you will need

  network of the HTTPS WEB object

  host 192.168.1.10

  NAT (inside, outside) interface static service tcp 80 80

  Now, 2 Site will naturally a little different that the server is hosted on the Site 1 and Site 2 is the public IP address used to publish the server on the external network.

  Essentially, you will need to configure NAT that both makes dynamic PAT for the addresses of the source of the connection to your server Web 2, but also makes the static PAT (Port Forward) for the IP address of the Web Server 2. Additionally, you have to set the area of encryption on the Site 1 and Site 2 to match this new addition to the L2L VPN connection.

  Unless of course you use an existing IP address on the field of encryption in the dynamic translation of PAT for the source address. In this case, it would take no change VPN L2L. I'll use that in the example below.

  The NAT configuration might look like this

  service object WWW

  destination eq 80 tcp service

  service object HTTPS

  destination eq 443 tcp service

  the object SOURCE-PAT-IP network

  host 192.168.3.254

  network of the WEB-SERVER-2-SITE1 object

  host 192.168.1.11

  NAT (outside, outside) 1 dynamic source no matter what static SOURCE-PAT-IP destination interface WEB-SERVER-2-SITE1 service WWW WWW

  NAT (outdoors, outdoor), 2 dynamic source no matter what static SOURCE-PAT-IP destination interface WEB-SERVER-2-SITE1 service HTTPS HTTPS

  So, essentially, NAT configurations above should ake 'all' traffic coming from behind 'outside' interface intended to "outside" "interface" IP address and translate the source to ' SOURCE-PAT-IP ' address and untranslate destination to "WEB-SERVER-2-SITE1".

  Make sure that the IP address chosen (in this case 192.168.3.254) is not used on any device. If she is then replace it with something that is not currently used in the network. Otherwise, configure an IP address of some other subnet and include in the L2L VPN configurations on both sites.

  Unless you already have it, you also have this configuration command to activate the traffic to make a U-turn/pin on the ' outside ' of the Site 2 ASA interface

  permit same-security-traffic intra-interface

  Hope this helps

  Remember to mark a reply as the answer if it answered your question.

  Feel free to ask more if necessary.

  -Jouni

• Limiting the number of users on IPSec VPN

  I have a Cisco ASA 5510 running an IPSec VPN. My example is I have a strategy of group with 10 users on it, all assigned static IP. Of those 10 users, I want to only have a maximum of 5 connected at any time. Concurrent connections do not work because it is only how many times a single user name can be connected (as I know) and I can't limit the pool of IP addresses of this group because I need 10 static IP addresses and if I have little of the pool 5, although that would not work.

  So is there anyway to limit the amount of VPN users by group policy or tunnel or do you have? I don't want to limit the ammout of a VPN connection across the unit as I have other groups that need to connect.

  Thanks for any help.

  You are absolutely right. There is no way to limit the number of single by group simultenous VPN connections. When you limit the connections to 5 per group, for example, it does not check if a user has been connecting simultenously 3 times.