Reference Dell 6248 find IP address port
Hi, I use a Dell 6248 switch and I want to spend the vlan of a particular device, but I do not know on which port the device is connected. How can I find this information without having to physically go to the switch.
I don't know if it's serious or not, but the switch dell isn't the switch doing the routing.
Hi, I left the company that had this switch in January 2013, so I wasn't able to test the last response before yours, but nothing before that worked.
Tags: Dell Switches
Similar Questions
-
Reference Dell M1000e + aggregator MI/O port mapping
Hi all
I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?
My hardware:
- 1 x Dell M1000e
- 2 x M i/o aggregator (A1 & A2)
- 16 x M630 Blade (Qlogic 57840 S ANC four ports card)
Reference DELL M/o aggregator:
(reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)
I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.
Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)
Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)
FYI - I would like to install ESXi 6.0 on all blades
Thank you!!
Vinay
Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.
You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.
Unidentified:
Dell (conf) # tengigabit interface 0/16
Dell(conf-if-te-0/16) # vlan unidentified 4
Output Dell(conf-if-te-0/16) #.
Tag:
Dell (conf) # tengigabit interface 0/16
The tag vlan Dell(conf-if-te-0/16) # 4
Output Dell(conf-if-te-0/16) #.
Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.
By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.
The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.
For redundancy, you could stack the units together. 241 page details the process of stacking.
Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.
-
Reference Dell 6248: hot swapping and upgrade battery links
I have a set of switches Dell 6248. I have a few questions to explore:
(1) can I add/remove the CX4 cables while the switch is working? (I guess it's the same rules as a cable normal Ethernet...)
(2) can I add/remove modules while the switch is working?
First scenario I'm looking at: extend the stack on a stacked rack.
I think the process here is, install a switch of spare with stacking module, run off battery cables to the battery, breaking and re-Assembly of the ring, then turn on the switch, confirm the ID stack and connectivity and migrate customers to it. I can totally hot cables plug the CS4, right?
Next scenario I'm curious: upgrade of 12G to 48G stack.
Can I exchange the accumulated 12 GB card and swap the 48G card in when the switch is on, or do I have to turn it off? Connectors on the 48G card the same? (CX4..) Can I / layout 48G and 12G cards in a pile during my upgrade? Is the maximum length of cable the same (3 m) on a stack of 48G?
Thank you!
-danny
Hey Danny,
The stackable modules are not hot-swappable. The cables are, but for the modules to detect that it must present when the switch is started. A reboot is also required for stacking on these ports using Ethernet. Yes 48 GB stackable modules also have a 3 meter cable.
-
Reference Dell 6248 as default gateway - next hop router
Hi all
I guess it's a matter of very basic network design. Good practice / can I use Dell 6248 layer 3 switch as the gateway / next hop router, even if the correct entry door is directly connected to the same subnet / vlan?
The problem is that we are making changes to our network, and have several routers on the edge of our network configured static routes so they can achieve our other subnets, local and remote. These static routes will need to be changed when we move from one circuit to another, but some border routers are managed provider, and it is inconvenient to reschedule. Also, sellers will have to do more than once, the road changes if we want to clean our ip addressing scheme after the move. Once the changes are made, the topology of the network likely will not change for a long time, so I would stick with static routing. Given that we can grasp and control the static routes in our Dell 6248, can we just say sellers use our Dell switch as the next hop router when they change their static routes?
I know that ip redirects could try to "correct" this inefficient configuration, and that could cause problems, at least during the transition phase. On a small network with 10 servers, 100 computers and 80 phones, is it without further consequence of routing for the Dell 6248 layer 3 switch, or is this something configuration you should avoid (for other reasons)? Thanks for your understanding!
Without seeing a topology, you may be a little difficult to give recommendations. Is the 6248 your switch? It connects to your firewall? All edge switches are like L3 switches that are basically their own broadcast domain? If so, then what you are wanting to do would work. All edge switches have a static route of coverage which directed traffic to the 6248. You then place a static route pointing to the firewall on the 6248.
If all switches are in L2 and the 6248 mode is the only L3 switch on the network. Then the switches will not need static routes.
-
Replace the battery. Reference Dell 6248
Hello!
We have a set of three Dell Powerconnect 6248 switches.
One of the switches must be replaced with the new one (same model).
the well known "pwcnt_stacking_switches.pdf" document does not say how to replace a member of the battery,
just how to add additional, or to remove switch a.
It is said in the documentation for the 3524 powerconnect switches:
Exchange of stacking of members
If a member of the stack with the same unit ID replaces an existing UnitID with the same ID of the unit, the
the previous device configuration is applied to the inserted stack MemberEven apply to 6248? This approach works?
How a stand-alone switch can be prepared to be added to the stack as some number of particular unit (excluding implementation stack-port mode battery)?
is it
Renumber (conf) #switch
?
Yes, guess I replace unit Number or number 2. (out of three)
Once I have remove the old unit 2 and insert a new one, the new switch will get UnitID = 4.
After I using renumber
switch 4 renumber 2
He will get all the previously attributed to the old switch 2 port configuration?
-
Reference Dell 6248, 7048 or force S50N 10?
Hello
We want to improve our switches ISCSI 5424 to Dell Powerconnect 6248, 7048, or Force 10 S50N toggle. The switches will be devoted to traffic for 3 en berries Equallogic ISCSI must be able to support a few additional tables.
Any advice?
Thank you.
Ok thank you.
-
Reference Dell MD3200i correct editing with IP system and the NIC for faster network speeds
Hi all
I worked on this project for a while now. I did a lot of research and have contacted Dell several times. I need help.
I have 2 sets of identical to use for Hyper-V clusters servers. We bought a Dell MD3200i in November, we also bought a Dell 5424 switch and a Cisco SLM2048 switch. These servers have Real Tek 2 network cards for iSCSI Jumbo frames is 9 k
The Dell MD3200i is two SAN controllers. Dell 5424 is the iSCSI optimized switch and Cisco is a 48 switch ports. iSCSI is on its own network that nothing else is connected to it. (There is an Iomega NAS and a promise Vtrak SAN Tech with all current domain of execution with iSCSI controller)
Reference Dell MD3200i controller 0 Port 0 192.168.130.101 controller 1 Port 0 192.168.131.101
Controller controller Port 1 0 192.168.130.102 1 1 192.168.131.102
Controller controller Port 2 0 192.168.130.103 1 2 192.168.131.103
Controller controller Port 3 0 192.168.130.103 1-3 192.168.131.104
Cisco switch has 1 VLAN n ° 1 on it and the 130 subnet inside elements. There are 8 connections to the switch. 4 controller 0 and 1 of each of the servers. It has an IP of 192.168.132.4, but that switch IP does not make difference. Lighted Jumbo frames
Dell switch has 2 of #1 for various things such as the domain controller, Vtrack, and SIN. Subnet 2 is 131 and has a total of 8 connectors inside. 4 in 1 controller and 1 from each of the servers. Lighted Jumbo frames. The switch IP address is 192.168.132.2
Groups of servers. Each server node running Windows 2008 R2 SP1 and running hyper-v with virtual server clusters / storage folder on them. 2 Realtek NIC with Jumbo frames made 9 k ProdNode1 and ProdNode2 have 12 Core i7 CPU with 12 GB memory, EXNode1 and ExNode2 have 12 Core i7 CPU with 24 GB of memory.
ProdNode1 iSCSI-1 192.168.130.110 ProdNode1 iSCSI-2 192.168.131.110
ProdNode2 iSCSI-1 192.168.130.120 ProdNode2 iSCSI-2 192.168.131.120
ExNode1 iSCSI-1 192.168.130.130 ExNode1 iSCSI-2 192.168.131.130
ExNode2 iSCSI-1 192.168.130.140 ExNode2 iSCSI-2 192.168.131.140
Portal discovery iSCSI on ProdNode1 went to 192.168.130.110 192.168.130.101 and 192.168.131.110 192.168.131.101 each of the other servers Discovery Portal have been pairs like this.
iSCSI tab click on add 8 MPIO sessions at each of the ports on the MD3200i from Dell, target. For example, I added 1 session of 192.168.130.101 using it. Add Session,--> activate--> Advanced Mutlipath--> Local--> IP 192.168.130.110 initiator and target 192.168.131.101 iSCSI adapter. This is repeated on all servers. 4 connections for each NIC.
The network is very slow. It revolved around 2 to 4 MB/MIN and it should be much faster. Initially, we had only the Cisco switch with only 1 VLAN and everything connected directly to it. I read somewhere that MPIO has been the problem, so I went through the same configuration but does not verify the MPIO checkbox above. Once this has been done, the network speed went up to 1.5 GB/Min but modular storage Dell was not happy, and virtual servers would fail and the connection is not very stable.
What wrong with my setup? Can I directly home and fix the servers directly to the PowerVault and will make stable and allow for failover and redundancy NIC? I need to get this stable so I can move with something else.
Thank you Ron
You will need to change your system of intellectual property on this:
rbrambleEX-Node1 iSCSI-1 192.168.130.130EX-Node1 iSCSI-2 192.168.131.130EX-Node2 iSCSI-1 192.168.132.140EX-Node2 iSCSI-2 192.168.133.140Prod-Node1 iSCSI-1 192.168.130.10Prod-Node1 iSCSI-2 192.168.131.10Prod-Node2 iSCSI-1 192.168.132.20Prod-Node2 iSCSI-2 192.168.133.20Reference Dell MD3200iController 0 Port 0 - 192.168.130.101 Jumbo Frames 9KController 0 Port 1 - 192.168.131.101 Jumbo Frames 9KController 0 Port 2 - 192.168.132.101 Jumbo Frames 9KController 0 Port 3 - 192.168.133.101 Jumbo Frames 9KController 1 Port 0 - 192.168.130.102 Jumbo Frames 9KController Port 1 1 - 192.168.131.102 Jumbo Frames 9KController 1 Port 2 - 192.168.132.102 Jumbo Frames 9KController 1 Port 3 - 192.168.133.102 Jumbo Frames 9KYour iSCSI sessions will be:
For EX-Node1:
-192.168.130.130 to 192.168.130.101
-192.168.130.130 to 192.168.130.102
-192.168.131.130 to 192.168.131.101
-192.168.131.130 to 192.168.131.102
For EX-Node2:
-192.168.132.140 to 192.168.132.101
-192.168.132.140 to 192.168.132.102
-192.168.133.140 to 192.168.133.101
-192.168.133.140 to 192.168.133.102
For Prod-Node1:
-192.168.130.10 to 192.168.130.101
-192.168.130.10 to 192.168.130.102
-192.168.131.10 to 192.168.131.101
-192.168.131.10 to 192.168.131.102
For Prod-Node2:
-192.168.132.20 to 192.168.132.101
-192.168.132.20 to 192.168.132.102
-192.168.133.20 to 192.168.133.101
-192.168.133.20 to 192.168.133.102
-
Original title: unable to print. Reference Dell 944 communication usb port is not available.
Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems. I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?
DavidNicholsonXN,
How to download and install drivers in the correct order
also try to read...
The owners of all-in-one printer Dell 944 thread (W7)
Let the printer after Kaspersky
Rick
-
Reference Dell 6248P - Guest Wifi VLAN config
I am trying to retrieve all upward of a VLAN. The VLAN is comments wireless traffic going through our main switches and on an ADSL router but I'm running into some difficulties.
We have 3 points of access for model AP - AC Unifi. Each access point has a connection of physical network of 1 of 4 Dell 6248 switches which are currently in a single stack managed as follows.
AP 1-> Port of the Switch 1 40
AP 2-> Port of the Switch 2 36
AP 3-> Port of the Switch 3 17
The managed pile and AP are currently using the 192.168.1.0/24 on VLAN 1 - default and I created a VLAN 10 - guest.
The APs have two SSID WLAN, 'corporate', which is also on the 192.168.1.0/24 range and 'guest' that is located on 192.168.99.0/24. I put the "guest" to mark its traffic with VLAN 10 and no DHCP is defined.
I put the 3 above general Mode ports, allowing all managers and VLAN - 1 that are not marked and VLAN - 10 they are labeled.
I also put a Zyxell router with a static address of 192.168.99.254 in Switch 4 Port 24 and set the access mode for VLAN 10.
The router is configured to provide DHCP for the beach of 192.168.99.0/24.
Now when I connect a laptop to our 'coporate' WLAN, everything works fine. I get a DHCP address from our server and I can reach everything as usual.
When I connect to the "guest" WLAN, I do not receive a DHCP address, in addition, I am able to ping on subnet 1 hardware VLAN I thought would not be possible.
Can someone take a look at this config and I would like to know what is the problem with him?
! Current configuration:
! Description of the system «PowerConnect 6248P, 3.3.12.1, VxWorks 6.5»
! 3.3.12.1 system software version
! Passage mode is configured as disabled
!
Configure
database of VLAN
VLAN 10
VLAN 10 1 routing
subnet of VLAN association 192.168.99.0 255.255.255.0 10
output
unicast SNTP client enable
192.168.1.18 SNTP server
battery
1 5 Member
2 5 Member
3-5 Member
4-5 Member
output
switch priority 1 12
IP 192.168.1.212 255.255.255.0
default IP gateway - 192.168.1.227
IP - my.domain domain name
name of the IP-server 192.168.1.18
name of the IP-server 192.168.1.19
name of the IP-server 192.168.140.2
IP routing
IP route 192.168.99.0 255.255.255.0 192.168.99.254
interface vlan 10
name of the "Guest".
Routing
IP 192.168.99.212 255.255.255.0
bandwidth 10000
IP helper-address 192.168.99.254 dhcp
IP mtu 1500
output
level of a8e64cdc85228f4c837da747958ffd74 user name 'admin' password encrypted 15
l2relay DHCP
DHCP l2relay vlan 2.10
!
interface ethernet 1/g7
Auto mode channel-group 2
output
!
interface ethernet 1/g8
Auto mode channel-group 1
output
!
interface ethernet 1/g40
switchport mode general
switchport general allowed vlan add 10 tag
output
!
interface ethernet 2/g36
switchport mode general
switchport general allowed vlan add 10 tag
output
!
interface ethernet 3/g2
Auto mode channel-group 2
output
!
interface ethernet 3/g17
switchport mode general
switchport general allowed vlan add 10 tag
output
!
interface ethernet 3/g48
Auto mode channel-group 1
output
!
interface ethernet 4/g24
switchport access vlan 10
output
outputI was looking back through the configuration, and on the 24 port setting, I see there is a command to access in place, but the port is not set to enter the mode. Can you try to put the port in access mode?
interface ethernet 4/g24
switchport mode accessDuring the test with the laptop plugged on the switch, we should test it first with a static IP address. This is to ensure that we have a connection established. Then you can move on to DHCP.
The router will appear in the output of one of these two commands?
console switch arp #show
#show bridge console table address
-
VLAN function 6248 switch IP address
We have a nice and simple class C private address space private on 4 x Dell 6248 switches. We are running out of IP addresses. We could change the netmask (add more bits), but who is to reach each node and potentially finding devices that do not work with anything other than 24. We have a lot of old material that we must keep functioning. In addition, we want to limit emissions, since here we have projects that do a lot of UDP broadcasts. If each project in one VLAN, the load on the switches would be less. Hosts on VLANS must get to the common servers well.
So I did some reading and thought we would use of VLANS, routing and others to have several C class spaces. We turn the material around the office at an alarming rate so I thought that an IP based VLAN would be an excellent solution. I have problems with the documentation and configuration to make it work.
We have 2 x 2716 Dell and 2 x Dell 2724 switches in the mix as well. They are connected to the 6248 s switches dumb and all seems to work now.
I created 2 VLAN and reports the following:
Curetes #show ip interface vlan 2
State of the Routing Interface... Down
Primary IP address... 192.168.3.1/255.255.255.0
Routing mode... Enable
Administrative mode... Enable
NET before realized emissions... Disable
Proxy ARP...................................... Enable
Local Proxy ARP... Disable
Statement of assets... Inactive
MAC address... 0019.B998. E71E
Type of encapsulation... Ethernet
IP MTU......................................... 1500
Bandwidth...................................... 10000 Kbps
Destination unreachable... Activated
ICMP redirects... ActivatedI am running firmware V3.3.3.3. I have improved the switches on the weekend of 2.2.0.3 I read that VLAN does work well with this version.
I can't find in the documentation "Setup Guide" or "CLI_EN.pdf" how to get the "Routing Interface status" that up to.
My config running is pretty simple:
! Current configuration:
! Description of the system "PowerConnect 6248, 3.3.3.3, VxWorks 6.5.
! 3.3.3.3 system software version
! Passage mode is configured as disabled
!
Configure
database of VLAN
VLAN 2-3, 10-11
VLAN 2 1 routing
VLAN 3 2 routing
subnet of VLAN association 192.168.3.0 255.255.255.0 2
output
hostname "curetes.
Select the SNTP client distribution
192.139.238.68 SNTP server
battery
1 2 Member
2 2 Member
3 2 Member
4 2 Member
outputIP 192.139.238.79 255.255.255.0
default IP gateway - 192.139.238.27
IP routing
interface vlan 2
name '192-168-3-x-address. "
Routing
address 192.168.3.1 IP 255.255.255.0
output
interface vlan 3
Routing
output
level XXXXXXXXXXXXXXXXXXX username 'admin' password encrypted 15
outputQuestion (in order of importance):
What is the best way to go to solve my problem (limit/exhaustion of Ip address space broadcast domain)?
How to make "Routing Interface Status" on VLAN 2 upward? Do I need it upward?
How to configure a VLAN to do what I want?
Thanks in advance.
Don
Yes, that's my suggestion.
-
Reference Dell 6248P - VLANS, DHCP, wireless AP
Hello
I'm trying to set up a VIRTUAL LAN for wireless comments traffic go through our main switches and on an ADSL router but I'm running into some difficulties.
We have 3 points of access for model AP - AC Unifi. Each access point has a connection of physical network of 1 of 4 Dell 6248 switches which are currently in a single stack managed as follows.
AP 1-> Port of the Switch 1 40
AP 2-> Port of the Switch 2 36
AP 3-> Port of the Switch 3 17
The managed pile and AP are currently using the 192.168.1.0/24 on VLAN 1 - default and I created a VLAN 10 - guest.
The APs have two SSID WLAN, 'corporate', which is also on the 192.168.1.0/24 range and 'guest' that is located on 192.168.99.0/24. I put the "guest" to mark its traffic with VLAN 10 and no DHCP is defined.
I put the 3 above general Mode ports, allowing all managers and VLAN - 1 that are not marked and VLAN - 10 they are labeled.
I also put a Zyxell router with a static address of 192.168.99.254 in Switch 4 Port 24 and set to this mode of trunk to VLAN 10.
The router is configured to provide DHCP for the beach of 192.168.99.0/24.
Now when I connect a laptop to our 'coporate' WLAN, everything works fine. I get a DHCP address from our server and I can reach everything as usual.
When I connect to the "guest" WLAN, I don't get a DHCP address. If I put a static address, I can't do a ping to the router.
Could someone tell me if my configuration is correct?
Thanks for the additional information and the display to the top of the config.
A couple of things I noticed the config:
-I don't see that whatever it is set to Switch 4 Port 24, which is the case the router Zyxell is plugged. If this port is not configured properly, it may not be able to see the communication on the VIRTUAL LAN. A config like this should work on Switch 4 Port 24.
# interface ethernet 4/g24
switchport mode access #.
# switchport VLAN 10 acccess
-You may need to configure a static route to highlight traffic VLAN to the router.
# ip route 192.168.99.0 255.255.255.0 192.168.99.254
I would like to know if any of this helps.
-
Hi team,
I'm new dell switches - exposed to cisco switches. I am faced with new kinds of problems with these dell switches. Unable to provide a fix and fight for the last 5 days. Pls help me. Below is my script
Two nw - 2.0 and 3.0 is required to be configured in VLAN, VLAN ID 2 and 3.
VLAN 2 - 192.168.2.1
VLAN 3 - 192.168.3.1
N/W 2.0 and 3.0 N/W machinery will be shared 48-Port powerconnect switch 5448 DELL
The routing part arrives at 6224 power connect - gateway for vlan 2 - 192.168.2.1 and bridge for VLANs 3 - 192.168.3.1
The switch of two is ascending through fiber optic - spf port cable
This is the configuration I did-
5448 switch-
database of VLAN
VLAN 2, 3
output
interface vlan 2
switchport access vlan 2
GVRP enable
Routing
output
interface vlan 3
switchport access vlan 3
GVRP enable
Routing
output
interface ethernet 1/you/1
switchport mode general
VLAN allowed switchport General add 2.3
GVRP enable
output
interface ethernet 1/g1
switchport access vlan 2
GVRP enable
output
interface ethernet 1/g2
switchport access vlan 3
GVRP enable
output
Uplink port is TE1 (Layer 2) to XG2 (Layer 3)
Reference Dell 6224 can connect
Configure the terminal
interface vlan 2
no downtime
IP 192.168.2.1 255.255.255.0
Routing
output
interface vlan 3
no downtime
address 192.168.3.1 IP 255.255.255.0
Routing
output
interface ethernet 1/xg2
switchport mode general
VLAN allowed switchport General add 2.3
GVRP enable
Computer with 192.168.2.100 / 24 GW 192.168.2.1 connected to layer 2 switch g1 - vlan 2
When I ping 192.168.2.1 - accessible United Nations host destination
Even the wise
Computer with 192.168.3.100 / 24 GW 192.168.3.1 connected to layer 2 switch g1 - vlan 3
When I ping 192.168.3.1 - accessible United Nations host destination
Any thing that has missed out in the configuration part / all bad entries. I'm not sure now how to treat this. Pls help me and it is an urgent task for me
Thank you
With multiple VLANs, you need to use the general/Trunk mode. With the help of the info we have I made a diagram to help show the location of the switches and parameters on them. Obviously things can be different, such as PVID, IP address, VLAN ID etc are all customizable to your needs. But the page layout modes and the port will remain the same.
STP will not fill the VLAN on the other switches. It's probably the GVRP feature it refers. With such a short race, it is more practical to manually add the VLAN. At least for the initial Setup, then once everything works enable GVRP to accommodate future expansion of VLAN.
Hope this helps some.
-
Reference Dell pc with xp family. Restart to the logon screen
Reference Dell pc with xp family. Restart to the logon screen. starts ok in safe mode. run msconfig and do that no change then do restart ok everything ok until the cold start, then hand it to restart?
Peek into the registry to find clues.
Disable the automatic restart in case of system error and see if you can capture a message of error checking bug (BSOD) with useful information. Automatic restart in the event of system failure can be disabled in the F8 advanced boot menu, or you can turn it off in system properties.
1. right click on my computer and select Properties.
2 - Click on the Advanced tab, and then click on the Start button and recovery settings.
3 clear the automatically restart box and OK your way out system properties.Start the computer in a Clean Boot State, if the computer starts successfully in a clean boot state, then one of your user programs most likely problems, look in the case of journal of indexes.
How to configure Windows XP to start in a "clean boot" State
John -
Could not find the address eprint for my HP 6500 has more
Help me understand how to find the address for my 6500 HP eprint has more printer so that I can set up Google cloud print on my new HP 14 "Chromebook.
Hi lbwmson,
Welcome to the HP Support forums. I understand that you want to configure your Officejet 6500 a more printer to work with your Chromebook.
We must first get the printer connected to your wireless network. This can be easily accomplished from the front panel of the printer. the instructions are on page 224 of your User Guide in the section titled "to set up wireless communication using the Wireless Setup Wizard".
The next step is to get your application Code when you enable web services. Once you have your request of code you want to Set Up A Custom Email Address of your printer.
We can now implement Google Cloud Print with your HP printer. For additional reference, I've also included how print a Page of Support of Google Chrome. If you plan to use the scanning function please consult your User Guide on page 41. It has a section entitled 'Analysis using Webscan'. It will guide you through the scanning you have with the Chromebook.
-
Reference Dell 3110cn of Laserjet + os El Capitan
My MacBook Pro (2009) stopped my Dell printer. News on this please.
Hi deaconjo,
as I had the same problem, I found a solution for my El Capitan MacPro 2008:
Search for the following installation program:
3130cn_Installer_And_Application_Dell_A04_MAC.dmg
Inside this package you will find the driver for 10.7 and higher. After installing the package I could add an IP printer with this driver:
Reference Dell 3130cn Color Laser v3017.104 PS
With this driver installed, I can use my printer Dell 3110cn without problem.
Perhaps it might help you too.
Concerning
Maybe you are looking for
-
Have seen similar positions, but no one says that it has been solved. I got this cushion idela U410 a year ago and it worked normally. A few months ago, he began to start very slowly when power cycles. A hibernation has been rapid. Now it never rises
-
I just joined this forum when I did a search on HP Envy hinge problems and found so many comments. I also have a problem with my left hinge, which causes the separation of my case. My computer is still on warranty for another week so I submitted an
-
A Visual Basic files running in the W510
Team dear Acer, I already ordered an acer emblematic tab 510 with Windows 8 operating system. I ask to confirm if I can install exe files created empty Visual studio in the tablet. If the same is supported by the Tablet PC OS. Quick response will be
-
I don't know what else to add.
-
Hello I just installed the Blackberry JDE 6 and JDK (newest). After installation, it ran very well, so I closed the JDE and attempted to reopen it, it gives me the error message Cannot find RIMIDEWin32Util.dll. It is a prerequisite of the IDE. I HAV