VLAN function 6248 switch IP address

Similar Questions

• Impossible to assign the IP address for VLAN 1 (6248)

  Nice day

  I bought two layer 3 PC 6248 switches. When I try to assign an IP address by default VLAN 1, it displays an error 'failed to remove management VLAN - ID ".  These predisposees are already preconfigured with the IP address 192.168.0.1 for VLAN 1. I would like to delete this IP address and assign one in the range 10.10.1.x for VLAN 1. But this is NOT possible.

  Can someone please help me to remove this preconfigured IP, so that I can attribute my interest?

  Thanking you,

  Sam

  
  

• Blocking MAC address on PowerConnect 6248 switch

  Hello

  I have a PowerConnect 6248 switch where we want to block a specific MAC address from the rest of the network.

  I created a list of MAC access with the following commands:

  Console (config) #mac access-list extended BLOCK
  Console (config-mac-access-list) #deny 001D.09D4.B08E ffff.ffff.ffff all

  Console (config-mac-access-list) #permit a whole

  I then apply it to all interfaces:

  console (config) #mac group-access BLOCK

  What ends by goes, is that all hosts connected to the switch are blocked when my rule should only be blocking the host with mac address 001D.09D4.B08E.

  What I am doing wrong?

  Thank you!

  Have you tried changing your statement to:

  Console (config-mac-access-list) #deny 001D.09D4.B08E 0000.0000.0000 everything

• How can I activate the function tab switch?

  I used the function tab switch a lot, and now it has been removed. Is there a way to activate it?

  Make sure the open tabs is checked.

  • Tools > Options > privacy > address bar: when you use the location bar, suggest:

      History
      Bookmarks
  [X] Open tabs
  

• My PowerConnect 6248 switch loses its settings when disconnected from the power

  Hello

  I'll put up a PowerConnect 6248 switch on my local network through Web interface (I can't use serial to do).

  I put the IP, login, password, a LAG, SNTP server address, etc.

  It works fine until I unplugged the power cord to the switch to simulate a power outage. When I plugged in the power cord, the switch will reboot by displaying its default settings and I release all of mine.

  Y at - it a specific command, I missed to save all my settings in the switch?

  Thank you for your help.

  Pascal.

  The switch has two separate configuration locations, a running configuration and startup configuration. This allows you to change configuration and test running before engaging them in the startup configuration. Once you have the running configuration, how you want it, you need to run the # copy running-config startup-config command, or just copy # run start.

  See you soon

• Having trouble getting the voice VLAN on the switch X1052P to work at all

  Can someone help me understand how to set up the voice VLAN X1052P? I spent several hours trying to get this working and it does not work. I spent about 4 hours on the phone with a Dell technician that night and he couldn't get it to work and finally gave up. He told me that I had to spend my warranty to ProSupport because he did not know how to solve the problem. What group of *. It's a simple configuration of VLAN. What must be so picky about? In any case...

  Setting up the VIRTUAL LAN must be fairly simple, but apparently on this switch is not. The user guide page 406 is not very useful except explaining what the different options. I must admit I am not an expert VLAN so I dunno I've misconfigured something. But remember, Dell technology could not operate either.

  Here's my situation... I have VoIP phones on my network connected to a network wall jack. Connected to phones are my computers of users. The computer of the user and its respective VoIP phone, both share the same data cable. Before replacing Cisco managed Internet service provider spend all it worked well. The problem is that they had direct access to our network so I removed the switch and installed the X1052P in its place. I talked to the ISP to let them know what I'm doing and they said everything I had to do was setup VLAN ID: 15 for the voice VLAN because this is the VLAN ID that the router uses to route telephone traffic. Router PSI is also the server DHCP VLAN 15 and issues IP for phones using 172.27.0.0/24 with a DHCP 172.27.0.50 range - 150.

  I tried to configure the switch using parameters of VLAN static and settings VLAN voice and neither one also seems to do what I want it to do.

  Network administration > VLAN > VLAN static

  Network administration > VLAN > Voice VLAN

  I activated the profile 'phone' on ports I want to added to the voice VLAN and it does not work. Moreover, 47 the switch port is connected directly to the ISP router and is configured as a trunk with the default port VLAN 1 unidentified and tag VLAN 15. For other ports I tried the general implementation, access and trunk of the parameters on each port to see if I could get something going and still nothing happens. When I set up the ports as General ports VLAN, I made adding VLAN VLAN 1 and VLAN 15 as a VLAN tagged not marked. It still does not.

  This is the short story from where I am now. Any help is greatly appreciated.

  FYI, as a follow up I finally solved the problem. I hope this information helps someone else that can encounter the same problem.

  After buying the ProSupport warranty upgrade ($121 out-of-Pocket mind you) and addressing a total of 4 technicians ProSupport expert technician a 3rd another level (only available via chat message between one of the ProSupport phone technicians and the 3rd Tier expert tech - i.e. I couldn't talk or chat with this person me) the consensus was that the material must be bad. When I bought the X1052P I bought two of them, so the best way to know if it was a bad switch was simply configure the other switch and see if the behavior occurs on this one, too. Well, this switch also restarted each time I assigned the profile 'phone' to more than 13 or 14 ports in the switch. It seems that it was not a hardware problem after all.

  I went back to the switch original and tried new things hoping that I could fall on a solution and it turns out that the solution was NOT to use the voice VLAN on the switch. It does not work!

  SOLUTION: I set the VLAN ID: 15 manually and no has not assigned any phone profiles to one of the ports. This is how I solved the problem.

  So he has bad software on the switch. I tried to see if there are updates of the firmware on the Dell support site, but there is none. Configure manually the phone VLAN was the solution. What a freaking nightmare which turned out to be. Maybe someone in Dell could note this problem and test in-house. And, if you want to compensate me for the 20 + hours I spent working on this problem, which has be great, too.

• PowerConnect 6248 switch

  I have a stack of 7 6248 switches. I added an 8th battery ok but I can get it configured like the rest.

  It just says: its on Default VLAN 1

  I have 3 VLAN 1.22 and 201. All ports show deafault VLAB but only switches 1-7 in the VLAN 22 and 201.

  How can I copy the config info to go to 8?

  1 default ch3-48,

  3/3/xg3-xg4.

  4/4/xg3-xg4.

  5/5/xg3-xg4.

  6/6/xg3-xg4.

  7/7/xg3-xg4.

  8/8/g2-g30.

  8/8/g32-g48.

  8/8/xg3-xg4

  22 c 1-2,

  1/1-g3/g48.

  1/1/xg3-xg4.

  2/2-g1/g48.

  3/g1-3/g48.

  4/4-g1/g48.

  5/5/g1-g48.

  6/6/g1-g48.

  7/g1-7/g48

  201 c 1-2,

  1/1/xg3-xg4.

  2/2-g1/g48.

  3/g48

  5/g1-5/g48

  1/1-g1/g2.

  1/1/xg3-xg4.

  3/g48, 5/g48

  If all ports are going to have the same configuration, you can configure them at the same time.

  Console (config) # interface range ethernet 8/8-g1/g48

  See you soon

• Reference Dell 6248 find IP address port

  Hi, I use a Dell 6248 switch and I want to spend the vlan of a particular device, but I do not know on which port the device is connected. How can I find this information without having to physically go to the switch.

  I don't know if it's serious or not, but the switch dell isn't the switch doing the routing.

  Hi, I left the company that had this switch in January 2013, so I wasn't able to test the last response before yours, but nothing before that worked.

• Incoming packets were discarded on Dell 6248 switch

  Hello guys,.

  I'm having a problem on my network. From time to time the icmp echo packets are lost and this causes our monitoring system trigger false alarms.

  I checked interfaces for switches and found the discarded packet counter is incremented in one of them.

  Flow control is enabled on the interface and there is no frame break sent.

  The duplex on both ends are correct are the port speeds.
  The firmware of the switch is 3.3.9.1 and the model is a PowerConnect 6248 switch.

  view statistics ethernet 1/g48

  Total packets received (bytes)... 2019770477
  Packets received 64 bytes... 945800
  Packets received from 65 to 127 bytes. 1105872
  Packets received from 128 to 255 bytes... 152970
  Packets received 256-511 bytes... 445738
  Packets received 512-1023 bytes... 155436
  Packets received 1024-1518 bytes... 414040
  Packets received > 1518 bytes... 634118
  64 bytes of RX and TX packets... 946019
  RX and TX 65-127 bytes packet... 3294655
  Packet RX and TX 128 to 255 bytes... 235082
  RX and TX 256-511 byte packets... 893732
  RX and TX 512-1023 byte packets... 311408
  RX and TX 1024-1518 byte packets... 436671
  RX and TX 1519-2047 bytes packets... 873826
  RX and TX 2048-4095 bytes packets... 0
  RX and TX-9216 4096 bytes packets... 0

  Total packets received without errors... 3853974
  Unicast packets received... 3421088
  Received multicast packets... 211575
  Received broadcast packets... 221311
  -Other - or ITU (q)
  Receive packets ignored... 506

  Total packets received with errors of MAC... 0
  Jabbers received... 0
  Fragments / sousdimensionnés has received... 0
  Alignment defects... 0
  FCS Errors..................................... 0
  Overruns....................................... 0
  802. 3 x Pause frames received... 0
  Unacceptable frame type... 0

  Total of transmitted packets (bytes)... 858789293
  64 byte packets transmitted... 219
  65-127 bytes transmitted packets... 2188783
  Packets transmitted 128 to 255 bytes... 82112
  256-511 bytes transmitted packets... 447994
  512-1023 bytes transmitted packets... 155972
  1024-1518 bytes transmitted packets... 22631
  Transmitted packets > 1518 bytes... 239708
  Size of the image of max... 1518

  Total packets transmitted successfully... 3137419
  Transmitted unicast packets... 3034928
  -Other - or ITU (q)
  Multicast packets transmitted. 1628
  Broadcast packets transmitted. 100863
  Transmit packets ignored... 0

  Total transmit packets ignored... 0
  Single Collision frames... 0
  Several images of Collision... 0
  Excessive Collision management... 0

  802. 3 x Pause frames transmitted... 0
  GVRP PDU received... 0
  GVRP PDUs of transmitted... 0
  GVRP failure records... 0
  BPDU: 0 sent, received 0

  EAPOL frames transmitted... 0
  EAPOL Start received frames... 0

  Thanks in advance.

  Humm,

  We have changed our duo of remote of a failure wan link and the interface mistakes of count stop. Everything is the same: traffic, applications, etc. Not a clue about what happened because there is a Linux between the equipment of the carrier and the switch (bad packets would have fallen in the interface of linux machine).

  We turn now to the carrier of the explanations/solutions.

  Thank you for your time!

• Latest Firmware for 6248 switch

  I want to ask you what is the latest firmware available for 6248 switch.

  I 3.3.14.2, the last?

  Thank you

  It is the most recent.  It just came out in December according to support.dell.com: www.dell.com/.../DriversDetails; Starts = 3504032857 & osCode = NAA & productCode = powerconnect 6248 switch & languageCode = EN & categoryId = NOR

  B

• What configuration of VLAN requires a switch connectivity defined as an access port?

  What configuration of VLAN requires a switch connectivity defined as an access port?

  By external switch tagging

• The VLAN on a Switch Standard

  I am currently creating a new environment and we have a number of VLANS trunked together, I created a Standard switch for our virtual machine-to-machine network and the DMZ network, have each VLAN resources shared.

  What is the best way to do it?

  That I should...

  Create a vss and create groups of ports of individual virtual machine for each VLAN IDS? (for example, a switch for virtual machine VLANS and a switch to DMZ with groups of individual ports?)

  Or should I create just a switch for each with all 4095 active?

  Hey, as previously stated, the large traps with it would be the single points of failure, but since you're ok with it, I'm going to shut up

  Configuring VMware site seems ok, if you do not touch the vSwitches default security settings.

  Regarding the loss of connectivity, I am looking for the reason outside of VMware (VLAN not on two physical switch ports, bad IP/gateway settings within the operating system prompted, etc..)

• PC 6248: Obtaining DHCP address for incorrect subnet.

  I recently inherited a Dell PowerConnect 6248, which I am not familiar with, and I'm trying to use it as a switch Layer 3.

  I have a 10 of VLAN with a network 10.10.10.0/24 and 11 VLAN with an associated network of 10.10.11.0/24.

  When I statically assigned addresses on the clients on the ports configured for these VLANs. I can ping other subnets, and traffic is routed correctly.

  I also support IP configured in the world pointing to my DHCP server, and I installed the DHCP scopes for the associated networks VLAN 10 and 11.

  When I connect a device to a port configured with VLAN 10, I get a the network 10.10.10.0/24 DHCP address.

  However, when I connect a device to a port configured with VLAN 11, I receive a DHCP address also in the 10.10.10.0/24 when he should be in the 10.10.11.0/24 network.

  The VLAN, routes and extended DHCP appear to be properly set up everywhere. Yet once, when customers use statically assigned addresses their VLANs and adequate networks, traffic is routed normally. But I'm getting DHCP addresses for the incorrect subnet for clients connected to the local network VIRTUAL 11.

  Any help is greatly appreciated!

  Looks like you're real close how it works, we just miss something in the configuration.

  When you configure the port for VLAN 11, which command do you run? Once it is configured for that VLAN, we can confirm that by simply running a show on this interface command.

  It may be useful to see the configuration running on the whole, this will help us to look for any possible changes, we can offer you.

  If you could give us a screenshot or the decrease in the size of the DHCP scope settings, we can help those look too.

  Thank you

• PowerConnect 6248 switch for Cisco router

  Hello

  I'm new to this forum and I have a problem at the moment between a Cisco router and a dell pc6248. The problem is that I lost conectivity in VLAN 1 when I connect the router to a trunk port in the switch, however I conectivity VLAN 2 through this link to trunk. The configuration of the switch:

  interface ethernet 1/g48

  switchport mode trunk

  switchport trunk allowed vlan add 1-2

  output

  interface ethernet 1/g43

  switchport mode access

  switchport access vlan 2

  output

  On router

  fast interface 0/1

  no ip address

  no downtime

  fast interface 0/1.1

  encapsulation dot1q 1 native

  IP 192.200.3.1 255.255.255.0

  fast interface 0/1.2

  encapsulation dot1q 2

  IP 192.168.51.33 255.255.255.248

  output

  With the above configuration, I lost conectivity with the host in the vlan 1 - 192.200.3.x/24, but I win conectivity VLAN 2, when I connect the router to the 48 trunk port in the switch. This means that the trunk link for VLAN 2 work but not for VLAN 1.

  I read on the port of general mode, where I can configure the pvid of the port as 1 (vlan1) and it would be the unttag VLAN (even natively in Cisco), and I can configure the VLAN 2 like the tag, all this in the same port. What do you think about this? Someone have set up something like that?

  Best regards

  Erasmo

  PD: I write from Chile, I apologize for my English.

  I agree with you, I would try the general mode on the PowerConnect switch.

  mode console # switchport general

  Console # switchport General allowed vlan add 2 tag

  Console # switchport pvid General 1

  Keep us updated.

• Routing between two VLANs on a switch in series SG300

  I've seen a lot of messages from people with problems of traffic between the two routing VLANS with some complex examples.  Can someone show a simple example for a SG300 switch (in layer 3 mode) to set up the two VLAN and send the traffic between VLANS without an external router?

  VLAN1 10.10.10.0

  VLAN2 10.10.20.0

  I tried to do through the UI and can't seem to make it work.  It seems that it must be very simple, so maybe I'm missing something in the GUI.

  Hi Chris,

  I did 5 minutes of recording that showed how I configured the two VLAN on my SG300 switch and layer 3-switched between the VLANS.

  You have no trouble getting to the GUI, so you will have no difficulty to setup in a few minutes...

  • Be sure to use the latest version of the SG300 package, with a bearable CLI.
  • to save your changes to the configuration at the end of the process.
  • the IP addresses that you create will be the address of default gateway for PC hosts on VLANs specified.
  • Recording can be interrupted at any time to perform configuration operations.

  Recording is now available on the website of the WebEx service. Click on the link below to read:

  https://Cisco.WebEx.com/ciscosales/LSR.php?at=PB&SP=MC&rID=55688352&RKEY=05e1fc5fff0d05da

  Configuration of VLAN

  Monday, October 24, 2011 11:02 New York time

  5 minutes

  Have fun

  Best regards, Dave