Reference Dell M610 Blade... Disk failure RAID1, spare disk 0:0:0 always showing in offline mode

Similar Questions

• Reference Dell MD3220 virtual disk - hot spare in use

  We have a Dell MD3220.  one of the hard drives was taken out by an end-user trying to exchange a defective disc. Then after that the good player has replaced the old drive was placed back into the appropriate slot. Now we have a hot spare (enclosure 0, slot 23) in lieu of an another hot spare (attachment 2, slot 22). The hot spare that is subbed for has been replaced by two new hard drives now and the hot spare in use has still not disappeared. any suggestions on what to do next?

  Virtual disk - hot spare in use

  Storage array: MD3220
  Disk group: 2
    Physical disk failure in the: attachment 2, slot 22
       Action (deletion) enabled service:  NO. 
         LED of action on service component:  NO.
    Replaced with a physical disk to: enclosure 0, slot 23
    Virtual disks: 3
       RAID level: 5
       Status:  Gradient

  Hello, GalaxyTechService.

  It is perhaps not as complicated as it may seem, in fact. There is a wizard that you can use to return the disk to the raid set. Right-click the affected virtual disk and select 'Replace physical disk' and use the wizard that opens.

  In the upper area will be "missing disks", and in the lower field will be options available to replace them.

  Then just follow the steps.

  Let me know how it goes.

• Reference Dell MD3000 virtual disk

  I have an environment to both nodes of ESX 4.0 and a shared storage (Dell MD3000, no iSCSI).

  On storage, I have 10 at 10K SAS drives.

  Virtual disk how I need to build? A two bigger or smaller?

  Thank you

  Max

  It is not a simple answer, because it depends on:

  • Good storage practices

  • Storage type and the type of disks

  • VM number, size and type of e/s

  • Max VM and e/s per LUN

  • Size Max LUN (less than 2 to - 512 b)

  In your case, with 10 discs and two nodes and storage running in active-passive mode, you can create 2 virtual disks.

  Create 2 different groups of RAID5 (also think about using 1 disk as a global hot spare) and in each virtual disk group build 1 (or more if the size is more than 2 TB - 512b).

  If you have a few VMS with high IO think also to use use 4 disks in RAID10 instead of RAID5 configuration.

  André

• Reference Dell M1000e Blade Server

  Hi all

  We have Dell M1000e Server Blade, 13 3 full height and 10 low-profile, I/O switch servers are A1, A2 B1B2 are MXL blade switches and C1, C2 are Brocade Fiber switches.

  mid-height servers are M630 PowerEdge Blade Server

  with 1. Port double QLogic 57810 - k 10 GB

  2 QLogic 57810-k dual port Mezz 10 GB KR ANC card for M-Series Blade servers

  3 Emulex LPM16002 Fibre Channel i/o Card 16Gbps

  and full height blade PowerEdge M820

  1 Broadcom 57810-k Dual port 10 GB KR

  2 Emulex LPM16002 Fibre Channel i/o Card 16Gbps

  the problem is when you first start, we received this message for full height only servers

  "A fabric mismatch detected for B1 Dell Blade mezzanine card"

  and full height servers only does not illuminate they keep flashing red

  What is the problem?

  It looks like the Emulex on the M820 may be installed in wrong mezzanine card. 1 to 3 media fabric C mezzanine card slots. do you know which slit it is currently installed in? Here is some additional info on removal and installation of the mezzanine cards.

  http://Dell.to/2bZ7Ohl

• Reference Dell pc with xp family. Restart to the logon screen

  Reference Dell pc with xp family. Restart to the logon screen. starts ok in safe mode. run msconfig and do that no change then do restart ok everything ok until the cold start, then hand it to restart?

  Peek into the registry to find clues.

  Disable the automatic restart in case of system error and see if you can capture a message of error checking bug (BSOD) with useful information.  Automatic restart in the event of system failure can be disabled in the F8 advanced boot menu, or you can turn it off in system properties.

  1. right click on my computer and select Properties.
  2 - Click on the Advanced tab, and then click on the Start button and recovery settings.
  3 clear the automatically restart box and OK your way out system properties.

  Start the computer in a Clean Boot State, if the computer starts successfully in a clean boot state, then one of your user programs most likely problems, look in the case of journal of indexes.

  How to configure Windows XP to start in a "clean boot" State
  John

• Reference DELL Blade - Ethernet Passthrough with ESX 4

  I have an environment DELL M1000e blade with M610 and M710 servers.  Running all ESX 4.

  Fabric A1: M6220 (the user's LAN Segment)

  Fabric A2: no

  Fabric B1: Ethernet Passthrough (iSCSI to DELL Equallogic PS5000e SAN)

  Fabric B2: Ethernet Passthrough (iSCSI to DELL Equallogic PS5000e SAN)

  All blade on ESX servers see the A1 and A2 as vmnic0 & vmnic1.  If I understand correctly, the M6220.  The problem is that none of the blades see Passthroughs Ethernet which are connected to a Cisco 2970 switch.  Shouldn't B1 & B2 appear on vmnic2 & vmnic3?  It does not show on the side of ESX.

  Any agency with experience with this would be useful.

  Thanks in advance.

  (1) chassis management controller can tell you what is installed.

  (2) Yes, you do.  If you want to connect to what in fabric B, each server needs to connect to fabric B need a Mezz card on fabric B.

• Reference Dell M1000e + aggregator MI/O port mapping

  Hi all

  I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?

  My hardware:

  • 1 x Dell M1000e
  • 2 x M i/o aggregator (A1 & A2)
  • 16 x M630 Blade (Qlogic 57840 S ANC four ports card)

  Reference DELL M/o aggregator:

  (reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)

  I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.

  Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)

  Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)

  FYI - I would like to install ESXi 6.0 on all blades

  Thank you!!

  Vinay

  Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.

  You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.

  Unidentified:

  Dell (conf) # tengigabit interface 0/16

  Dell(conf-if-te-0/16) # vlan unidentified 4

  Output Dell(conf-if-te-0/16) #.

  Tag:

  Dell (conf) # tengigabit interface 0/16

  The tag vlan Dell(conf-if-te-0/16) # 4

  Output Dell(conf-if-te-0/16) #.

  Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.

  By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.

  The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.

  For redundancy, you could stack the units together. 241 page details the process of stacking.

  Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.

• Reference Dell E6420 randomly not SSD detection at startup

  Specifications of the computer:

  Dell Latitude E6420, Intel Core i5 2520 M, 2 x 4 GB = 8 GB of RAM, Nvidia NVS 4200 M, 250GB HDD, Win 7 Pro 64, Bios A23

  The value of operation SATA AHCI and not quick start. I have 3 of these computers. They are all out of warranty.

  I replaced the original 7mm Hitachi 250 GB for the Intel 535 240 GB SSD HARD drive.

  I used Acronis True Image 2016 to clone the hard disk SSD. Cloning process is very much like on any other computer.

  The problem is that each cold 4 or 5 boots the computer cannot find the SSD drive. Restarting the computer solves the problem of that time. I have to find a solution. I want to sell them with a SSD and not with a HARD drive.

  I tried the things:

  Update the Bios of the A14 to A23.

  Put a spacer of 2mm on the SSD and of course the resettlement of the SSD.

  Exchange for another Intel 535 120 and 240 GB.

  Clean install of windows I knew was a waste of time because it does not affect the BIOS does not detect not things.

  Googling the problem for hours.

  Call dell?

  Use another brand of SSD? He probobly won't make any difference to look at other threads.

  Use a HARD drive? Last resort. I can't stand slow hard disks regularly.

  Reference Dell E6420 seems to work with a Samsung 850 Evo 250 GB instead of the Intel 535 very well. Tested over a period of 3 months with no problems. Threw 535 readers intel in the desktop instead.

• Reference Dell MD1200, H710 with R720XD

  Hello

  Asked if drieves NL - Seagate SAS (ST4000NM0023) can be used in the following configuration.

  Reference Dell Perc H710 + PowerEdge R720XD MD1200.

  The answer that I gave them was who should be tested. Because in documentation it is stated that mark Dell hard disks should be used.

  I know that some controllers Perc will give a warning each time if not dell disks are used, but they work without problems. Is this the case even when you use a box MD1200?

  Kind regards

  Indrek

  INDRP,

  You're right that only some drives are tested and supported in the bays of the MD. Here is a link that will take you to one of the manuals that list all drives supported for 1200 MD and MD1220.

  FTP.Dell.com/.../PowerVault-md1200_Reference%20Guide_en-US.pdf

  Please let me know if you have other questions I would be happy to help.

• Reference DELL VRTX Shared Storage for cluster

  Dell administrator and specialist out there, I need help!

  I have a VRTX and 2 nodes of Cluster of Windows Server 2012 Hyper-V running. I want to migrate to Windows Server 2012 Hyper - V R2 cluster (using another 2 blades) but will use existing storage. Seems that I can't use the existing storage again, I assigned the virtual disk of the CMC. In Failover Cluster Manager > disc, I got error "the requested resource is in use. Cluster event log, I got:

  1069-

  Cluster resource ' Cluster disk 1' type "Physical disk" in the role of cluster '9c5e9411-cddd-4496-8 ch. 57-9be758e788a1' failed. "

  1038 - ownership of cluster disk 'disk 1' Cluster unexpectedly lost by this node.

  I'm currently stuck here. Cannot make the 2012 R2 to access the existing cluster disk. Can someone tell me what is my mistake, and if there is no action to be performed on the CMC or Windows?

  Thanks in advance for your help...

  Found the answer. See the CSV property. During migration, the cluster to copy can be used to migrate the roles of clusters. But the disc may not be online on two clusters as a cluster have the property. So the steps, you must run the cluster to copy first, then turn off your VM on the old cluster and make the CSV file in offline mode. Then do the WB Online on the other node, run your VM on your new node with the new cluster. This solved my issue.

• Reference Dell 1700 crashed and I have no backup

  Reference Dell 1700 crashed without backup whats a girl to do
  
  

  lost all programs can run does not help

  Reference Dell 1700 crashed without backup whats a girl to do

  
  

  lost all programs can run does not help

  Reinstall Wndows.

  Reinstall all your programs from the original media or downloaded files you have saved on an external drive.

  Reinstall all your data from the backups that you made on an external drive.

  If you have not, you're out of luck.

• Reference Dell vostro 1520 with windows xp prof... Not reading CD/DVD

  Reference Dell vostro 1520 with windows xp prof... Unable to read & play any cd/dvd.tried mr.fixit content but no solution at the moment.

  Hello

  1 have. what fixit you tried?
  2. don't you make changes to the computer before the show?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  Important: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in the window.

• Cannot print. Reference Dell 944 communication usb port is not available. error check your firewall settings to ensure the printer communication is not blocked.

  Original title: unable to print. Reference Dell 944 communication usb port is not available.

  Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems.  I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?

  DavidNicholsonXN,

  How to download and install drivers in the correct order

  also try to read...

  The owners of all-in-one printer Dell 944 thread (W7)

  Let the printer after Kaspersky

  Rick

• M1000e with M610 Blade. iDRAC6 problems with the upgrade of the firmware 3.50 (Build 4) - "image downloaded missed the check" error

  I have the blade that is a M610. its current 3.30 iDRAC6 Firmware version (Build 17), his version of BIOS is 6.0.7. I am trying to upgrade the firmware to 3.50 iDRAC (Build 4). I am upradging by the MCC on the M1000e chassis. I choose the slot of in that the blade is and then start the IDRAC GUI. I choose firmware update and select the firming.imc file that I used successfully on some other M610 blades. After about 30 seconds, he returned with the following error.

  The uploaded image has no verification

  Why?

  I came across the same problem (with a refurb M610, iDRAC firmware has been 2.20).

  I tried to upgrade the iDRAC6 firmware to 3.60 via the web interface of iDRAC6 and it was a no go.

  I tried several browsers (chrome and firefox) and same problem each time.
  I tried to go to firmware (as shown in the accompanying note) 2.31 instead of 3.60 and same question every time.

  I finally managed to update the firmware of the iDRAC6 by upgrading the web interface M1000e and not in the iDRAC6 web interface.

  It worked the first time (using Chrome).

• Reference DELL T420 - battery on PERC H710 adapter controller

  Hello

  I received a yellow warning

  Reference DELL T420 'Battery on PERC H710 adapter controller'

  What it means?

  What should I do?

  Order the new battery?

  It is a simple replacement mission?

  Is it essential?

  Update:

  test URL

  http://www.Dell.com/support/article/us/en/04/SLN130018

  Have nothing, everything seems fine now...

  Thank you

  It is normal so he can make a full discharge of the battery as part of his learning cycle every 90 days. Make sure that this isn't that. If this isn't the case, the reason, give it 24 hours. If it is fully charged, update the system (including RAID firmware, driver first) firmware. If not fully charged yet or it reproduces quickly, then replace the battery - power down to replace.