Reference Dell T310 - laboratory home

Similar Questions

• Cannot print. Reference Dell 944 communication usb port is not available. error check your firewall settings to ensure the printer communication is not blocked.

  Original title: unable to print. Reference Dell 944 communication usb port is not available.

  Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems.  I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?

  DavidNicholsonXN,

  How to download and install drivers in the correct order

  also try to read...

  The owners of all-in-one printer Dell 944 thread (W7)

  Let the printer after Kaspersky

  Rick

• Reference Dell MD3200i correct editing with IP system and the NIC for faster network speeds

  Hi all

  I worked on this project for a while now. I did a lot of research and have contacted Dell several times. I need help.

  I have 2 sets of identical to use for Hyper-V clusters servers. We bought a Dell MD3200i in November, we also bought a Dell 5424 switch and a Cisco SLM2048 switch. These servers have Real Tek 2 network cards for iSCSI Jumbo frames is 9 k

  The Dell MD3200i is two SAN controllers. Dell 5424 is the iSCSI optimized switch and Cisco is a 48 switch ports. iSCSI is on its own network that nothing else is connected to it. (There is an Iomega NAS and a promise Vtrak SAN Tech with all current domain of execution with iSCSI controller)

  Reference Dell MD3200i controller 0 Port 0 192.168.130.101 controller 1 Port 0 192.168.131.101

  Controller controller Port 1 0 192.168.130.102 1 1 192.168.131.102

  Controller controller Port 2 0 192.168.130.103 1 2 192.168.131.103

  Controller controller Port 3 0 192.168.130.103 1-3 192.168.131.104

  Cisco switch has 1 VLAN n ° 1 on it and the 130 subnet inside elements. There are 8 connections to the switch. 4 controller 0 and 1 of each of the servers. It has an IP of 192.168.132.4, but that switch IP does not make difference. Lighted Jumbo frames

  Dell switch has 2 of #1 for various things such as the domain controller, Vtrack, and SIN. Subnet 2 is 131 and has a total of 8 connectors inside. 4 in 1 controller and 1 from each of the servers. Lighted Jumbo frames. The switch IP address is 192.168.132.2

  Groups of servers. Each server node running Windows 2008 R2 SP1 and running hyper-v with virtual server clusters / storage folder on them. 2 Realtek NIC with Jumbo frames made 9 k ProdNode1 and ProdNode2 have 12 Core i7 CPU with 12 GB memory, EXNode1 and ExNode2 have 12 Core i7 CPU with 24 GB of memory.

  ProdNode1 iSCSI-1 192.168.130.110 ProdNode1 iSCSI-2 192.168.131.110

  ProdNode2 iSCSI-1 192.168.130.120 ProdNode2 iSCSI-2 192.168.131.120

  ExNode1 iSCSI-1 192.168.130.130 ExNode1 iSCSI-2 192.168.131.130

  ExNode2 iSCSI-1 192.168.130.140 ExNode2 iSCSI-2 192.168.131.140

  Portal discovery iSCSI on ProdNode1 went to 192.168.130.110 192.168.130.101 and 192.168.131.110 192.168.131.101 each of the other servers Discovery Portal have been pairs like this.

  iSCSI tab click on add 8 MPIO sessions at each of the ports on the MD3200i from Dell, target. For example, I added 1 session of 192.168.130.101 using it. Add Session,--> activate--> Advanced Mutlipath--> Local--> IP 192.168.130.110 initiator and target 192.168.131.101 iSCSI adapter. This is repeated on all servers. 4 connections for each NIC.

  The network is very slow. It revolved around 2 to 4 MB/MIN and it should be much faster. Initially, we had only the Cisco switch with only 1 VLAN and everything connected directly to it. I read somewhere that MPIO has been the problem, so I went through the same configuration but does not verify the MPIO checkbox above. Once this has been done, the network speed went up to 1.5 GB/Min but modular storage Dell was not happy, and virtual servers would fail and the connection is not very stable.

  What wrong with my setup? Can I directly home and fix the servers directly to the PowerVault and will make stable and allow for failover and redundancy NIC? I need to get this stable so I can move with something else.

  Thank you Ron

  You will need to change your system of intellectual property on this:

  rbramble

  EX-Node1 iSCSI-1 192.168.130.130

  EX-Node1 iSCSI-2 192.168.131.130

  EX-Node2 iSCSI-1 192.168.132.140

  EX-Node2 iSCSI-2 192.168.133.140

  Prod-Node1 iSCSI-1 192.168.130.10

  Prod-Node1 iSCSI-2 192.168.131.10

  Prod-Node2 iSCSI-1 192.168.132.20

  Prod-Node2 iSCSI-2 192.168.133.20

  Reference Dell MD3200i

  Controller 0 Port 0 - 192.168.130.101 Jumbo Frames 9K

  Controller 0 Port 1 - 192.168.131.101 Jumbo Frames 9K

  Controller 0 Port 2 - 192.168.132.101 Jumbo Frames 9K

  Controller 0 Port 3 - 192.168.133.101 Jumbo Frames 9K

  Controller 1 Port 0 - 192.168.130.102 Jumbo Frames 9K

  Controller Port 1 1 - 192.168.131.102 Jumbo Frames 9K

  Controller 1 Port 2 - 192.168.132.102 Jumbo Frames 9K

  Controller 1 Port 3 - 192.168.133.102 Jumbo Frames 9K

  Your iSCSI sessions will be:

  For EX-Node1:

  -192.168.130.130 to 192.168.130.101

  -192.168.130.130 to 192.168.130.102

  -192.168.131.130 to 192.168.131.101

  -192.168.131.130 to 192.168.131.102

  For EX-Node2:

  -192.168.132.140 to 192.168.132.101

  -192.168.132.140 to 192.168.132.102

  -192.168.133.140 to 192.168.133.101

  -192.168.133.140 to 192.168.133.102

  For Prod-Node1:

  -192.168.130.10 to 192.168.130.101

  -192.168.130.10 to 192.168.130.102

  -192.168.131.10 to 192.168.131.101

  -192.168.131.10 to 192.168.131.102

  For Prod-Node2:

  -192.168.132.20 to 192.168.132.101

  -192.168.132.20 to 192.168.132.102

  -192.168.133.20 to 192.168.133.101

  -192.168.133.20 to 192.168.133.102

• Reference Dell 1700 crashed and I have no backup

  Reference Dell 1700 crashed without backup whats a girl to do
  
  

  lost all programs can run does not help

  Reference Dell 1700 crashed without backup whats a girl to do

  
  

  lost all programs can run does not help

  Reinstall Wndows.

  Reinstall all your programs from the original media or downloaded files you have saved on an external drive.

  Reinstall all your data from the backups that you made on an external drive.

  If you have not, you're out of luck.

• wiring replaced with SSD HD & put Dell Windows XP Home SP2 on again but does not refresh

  I removed my old drive hard-working mill & replaced with a SSD OCZ, 90 GB and put on Dell Windows XP Home SP2.  When I try to update windows, I have error 0x8024400A or # 0 x 80240036.  All the appropriate Dell drivers have been resettled.  Microsoft Fixit won't work because there is no SP3 on the computer.  Thanks in advance for any help.

  Click HERE. Download the batch file. Save the file to your desktop. Double-click on the file. This file stores some Windows dll files related to Windows Update. You should receive several confirmation that files are saved. Close the view and try to update Windows again.

  If still no joy, click HERE. Download sp3. Save the file to your desktop. Double-click the file to run it. Follow the prompts to install sp3. Try to update again once installation is complete.

• Reference Dell vostro 1520 with windows xp prof... Not reading CD/DVD

  Reference Dell vostro 1520 with windows xp prof... Unable to read & play any cd/dvd.tried mr.fixit content but no solution at the moment.

  Hello

  1 have. what fixit you tried?
  2. don't you make changes to the computer before the show?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  Important: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in the window.

• Reference Dell pc with xp family. Restart to the logon screen

  Reference Dell pc with xp family. Restart to the logon screen. starts ok in safe mode. run msconfig and do that no change then do restart ok everything ok until the cold start, then hand it to restart?

  Peek into the registry to find clues.

  Disable the automatic restart in case of system error and see if you can capture a message of error checking bug (BSOD) with useful information.  Automatic restart in the event of system failure can be disabled in the F8 advanced boot menu, or you can turn it off in system properties.

  1. right click on my computer and select Properties.
  2 - Click on the Advanced tab, and then click on the Start button and recovery settings.
  3 clear the automatically restart box and OK your way out system properties.

  Start the computer in a Clean Boot State, if the computer starts successfully in a clean boot state, then one of your user programs most likely problems, look in the case of journal of indexes.

  How to configure Windows XP to start in a "clean boot" State
  John

• Reference Dell M1000e + aggregator MI/O port mapping

  Hi all

  I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?

  My hardware:

  • 1 x Dell M1000e
  • 2 x M i/o aggregator (A1 & A2)
  • 16 x M630 Blade (Qlogic 57840 S ANC four ports card)

  Reference DELL M/o aggregator:

  (reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)

  I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.

  Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)

  Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)

  FYI - I would like to install ESXi 6.0 on all blades

  Thank you!!

  Vinay

  Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.

  You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.

  Unidentified:

  Dell (conf) # tengigabit interface 0/16

  Dell(conf-if-te-0/16) # vlan unidentified 4

  Output Dell(conf-if-te-0/16) #.

  Tag:

  Dell (conf) # tengigabit interface 0/16

  The tag vlan Dell(conf-if-te-0/16) # 4

  Output Dell(conf-if-te-0/16) #.

  Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.

  By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.

  The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.

  For redundancy, you could stack the units together. 241 page details the process of stacking.

  Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.

• Reference DELL T420 - battery on PERC H710 adapter controller

  Hello

  I received a yellow warning

  Reference DELL T420 'Battery on PERC H710 adapter controller'

  What it means?

  What should I do?

  Order the new battery?

  It is a simple replacement mission?

  Is it essential?

  Update:

  test URL

  http://www.Dell.com/support/article/us/en/04/SLN130018

  Have nothing, everything seems fine now...

  Thank you

  It is normal so he can make a full discharge of the battery as part of his learning cycle every 90 days. Make sure that this isn't that. If this isn't the case, the reason, give it 24 hours. If it is fully charged, update the system (including RAID firmware, driver first) firmware. If not fully charged yet or it reproduces quickly, then replace the battery - power down to replace.

• Reference Dell E6540 does not capture sound thanks to the headset

  I have a Turtle Beach Ear Force 50 Recon I bought recently.

  I have connected to my computer (an E6540) with the microphone and plugged everything.

  However, as far as I can tell, it's continuing to capture sound through the laptop itself. This somewhat defeated the purpose the purchase of a headset with a microphone, so if you have ideas, please let me know. And if you need more information, just ask.

  Sorry for the delay. Sounds like a driver problem, so what I would do is to try all the drivers available and see if any of them solves the problem. I would like to start by completely removing the existing driver from Realtek.

  Open Device Manager and expand the sound controllers section. Right click on the Realtek, and select uninstall. Put a checkmark in the option to delete files, click ok. When you restart, Windows either will install its own native driver or a Realtek driver if there was other versions on the hard drive. Then go back to Device Manager and look for a Realtek driver. Keep the uninstall & reboot until Realtek no longer appears under controllers, noise and "High definition Audio Device" appears in its place.

  Then I would try all the Realtek drivers that are available for the E6540 w/Win7, in order of oldest to newest. I hope that all of these links work - this forum has a difficult time to manage the links sometimes.

  http://www.Dell.com/support/home/drivers/DriversDetails?ProductCode=latitude-E6540-laptop&driverId=TFD11

  

  http://www.Dell.com/support/home/drivers/DriversDetails?ProductCode=latitude-E6540-laptop&driverId=Y8V8V

  

  I would do it in this order because you should be able to install a newer driver on a former without first having to remove the old.

  You can also try directly a Realtek driver:

  1. go to the Realtek download selection page. http://www.Realtek.com.tw/downloads/
  2. on the page, click on 'High Definition Audio Codecs.
  3. check "I accept", then "next".
  4. (optional) in the column named "Description" find the file named README and download it. Who has the instructions for the installation or update.
  5. in the column named "Description" select your operating system and if it is 32-bit or 64-bit of 2 choices in the list.
  6. in the column named "Download", click one of the server names to download the driver.

• Reference Dell Open manage for PE2950 for WS2012R2

  I tried to access the management system opened on our hyper-v Server today, but my manager told me that there is no such thing as a version of open management, for the PE2950 on Windows Server R2 2012 and it is out there for something fancy like a R6 * / 7 * /-8 *.

  I know it's there because I installed it in the last company I did part of the management, but for the life of me, only two years later, I can not understand where we got the original installation to do this.

  I downloaded installed three or four to manage open on the page drivers for our service number, but one of them came with "[I'm just a patch]" and the other three have indicated that they were not compatible. Even if we set the operating system to Windows Server 2012 R2, it always gives me "for 32-bit node,' then maybe we're missing something else.

  I am hoping to win the lottery here and have a Dell technician take pity on me and direct me to a FTP location I can give to my manager so that we can get this software down to all the systems in our network.

  I can't be the only person who has faced this issue, but I may be the only person who was not able to fix it on their own.

  Help, please.

  daveepperson86

  I tried to access the management system opened on our hyper-v Server today, but my manager told me that there is no such thing as a version of open management, for the PE2950 on Windows Server R2 2012 and it is out there for something fancy like a R6 * / 7 * /-8 *.

  Fake. You will find it at support.Dell.com, select your system, change the selection in the drop-down list of OS, then check out managing systems for OpenManage Server Administrator (Managed Node). The 32-bit version is fine and installation of WoW 64-bit operating systems will be activated (all except the ' core' by default).

  http://www.Dell.com/support/home/us/en/19/drivers/DriversDetails?driverId=V1JDD

  You can also go to http://ftp.dell.com.

• Reference Dell 3110cn of Laserjet + os El Capitan

  My MacBook Pro (2009) stopped my Dell printer. News on this please.

  Hi deaconjo,

  as I had the same problem, I found a solution for my El Capitan MacPro 2008:

  Search for the following installation program:

  3130cn_Installer_And_Application_Dell_A04_MAC.dmg

  Inside this package you will find the driver for 10.7 and higher. After installing the package I could add an IP printer with this driver:

  Reference Dell 3130cn Color Laser v3017.104 PS

  With this driver installed, I can use my printer Dell 3110cn without problem.

  Perhaps it might help you too.

  Concerning

• Reference Dell Sonicwall SRA

  Hey guys, more of a statement than a question. If you have a Dell Sonicwall and users do "found no appropriate group" of course the same user does not exist as a local user and a domain user. This will cause problems. Took me a while to understand that >.<>

  Good thought.

  Thank you
  Ben D
  Reference Dell SonicWall
  #Iwork4dell

• Reference Dell 2007FP vs HP zr22w

  Hi guys, I use t410s now. You want to find an IPS monitor. Currently have two choices.

  Reference Dell 2007FP (handed to nine 30-day warranty) $95

  HP zr22w (new, 3-year warranty) $175

  What would be a good choice?

  Not for the game.

  But need good color, good text, Word process, sometimes a movie.

  The HP zr22w DP, is better than the VGA to connect to my T410s?

  

  Thank you!

  Your information is so helpful. But I think that I can not check the number helpfully I ordered from DELL FINANCIAL SERVICES. Thank you very much!

• Reference Dell place 8 just out of warranty and dead now?

  Hello

  Everyone has a glue on Earth how to contact Dell technical support? My Tablet has acted weird for a while, but now it is completely dead and the custom lights at all. Previously, I got past pressing buttong for 10-15 minutes sometimes and then after a while it just turns itself off again. So now it's offshore and dead.

  I searched web pages of Dell support for direct contacts, but not luck. And worse, that it turns out that the warranty has ended in 12/09/14

  What a *.

  Reference Dell of mobile devices (phones) & tablets
  1-800-308-3355 24 / 7

  http://www.Dell.com/support/contents/us/en/19/category/contact-information/technical-support?c=us&l=en&s=DHS&CS=19