regulated 6.3UR pix PIX software

Similar Questions

• When it will be released version 6.3 of the PIX software?

  When it will be released version 6.3 of the PIX software?

  If all goes well at the end of this month or early April. Keep control on the BCC for the software, you will commit to the standard repository of PIX.

• The PIX software update

  To upgrade the software on the PIX 515, I just need to publish the following:

  copy the flashftp://172.16.6.100/pix622.bin t

  and then reload?

  Seems too easy.

  What is your current image? If its 5.1 or higher, then you are fine with your orders. If before 5.1, then you still have work to do (because they have no copy command. Need to start monitoring and upgrade mode in this mode). In addition, you are tipping? If so, first make the secondary pix (cables, upgraded, reconnect, disconnect active, upgrade, plug) then the active primary PIX.

  It will be useful.

  Steve

• PIX software

  Hello

  I'm going to update my version of software (520) PIX from 6.2 to 6.3 (3). But I want to take backup of existing version 6.2

  copy flash tftp - this command does not exist.

  Is it possible to copy existing software for backup?

  Please help me.

  Ishwar

  Hi Philippe,.

  Please send e-mail to scott (cisco), please read the following post (published recently):

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.eea04c4

  Thank you - Jay

• Need recommendation for PIX logging software

  Hello

  I need a recommendation for a PIX software logging so that I can better manage my PIX 525 and 515 firewall. I am currently using Cisco Syslog and I want something that I can set up specific, priority alerts, send email or page... etc. Your help would be most appreciated.

  Thank you

  You can use: KIWI Syslog

  http://www.kiwisyslog.com/software_downloads.htm#download%20Now

  Commercial products:

  Cisco VMS = http://www.cisco.com/go/vms

  Sawmill = http://www.sawmill.net/

  IQR = http://www.eiqnetworks.com/products/products.shtml

  sincerely

  Patrick

• software upgradation PIX

  Dear all

  We can move from the 6.2 (2) PIX software to directly 6.3 (3) directly... or is it gives no problems. Pls discuss the issue.

  Thanks in advance.

  Thanks and greetings

  Niasse

  As long as the software version > 5.1, you can use the copy flash tftp protocol command to upgrade the existing image to the new image.

• Remote access VPN Client to PIX, DNS issue

  Hi all.  I searched on this, but I can't find my answer.

  I set up a VPN connection to a PIX Firewall (running the version 8.0 (4)) for my business.  The VPN connection works correctly, in that I can connect to it using my software (v 5.0.02.0090) Cisco VPN Client and ping servers/resources internal IP address. However, if I try to ping by host name, it does not resolve to an IP address.  If I open a command prompt on my PC and type ipconfig/all, there are no DNS servers for my VPN, just for my normal Intel NIC adapter - I think I should have a DNS server listed under the map of VPN, right?  Here is the relevant (I think) for the VPN config lines:

  8.0 (4) version PIX

  domain xx.xx

  DNS lookup field inside

  DNS server-group DefaultDNS

  Server name 192.168.20.23

  domain xx.xx

  IP local pool vpnpoolIT 10.10.8.2 - 10.10.8.254 mask 255.255.255.0

  Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet

  Crypto-map dynamic dyn1 1jeu transform-set FirstSet

  Crypto-map dynamic dyn1 1 lifetime of security association set seconds 28800

  Crypto-map dynamic dyn1 kilobytes of life 1 set security-association 4608000

  crypto ISAKMP policy 1

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  tunnel-group ITGroup type remote access

  tunnel-group ITGroup General attributes

  address vpnpoolIT pool

  Group-RADIUS authentication server

  tunnel-group ITGroup ipsec-attributes

  pre-shared-key *.

  Am I missing?  I can solve the DNS on the PIX itself requests.

  All the info I can find online is for an older version of the PIX software which says that I should enter the vpngroup dns- IP address of the server command, but this command is not available in my version of the software.

  Hello

  To set a DNS server to be injected into the VPN clients when they connect, you can do the following:

  This is the tunnel-group where lands the remote connection:

  tunnel-group ITGroup type remote access

  tunnel-group ITGroup General attributes

  address vpnpoolIT pool

  Group-RADIUS authentication server

  tunnel-group ITGroup ipsec-attributes

  pre-shared-key *.

  For example, create a group policy:

  internal VPN group policy
  attributes of VPN group policy

  DNS value--> x.x.x.x where x.x.x.x is the IP address of the DNS server

  Then, apply the group policy for the Group of tunnel:

  tunnel-group ITGroup General attributes

  Group Policy - by default-VPN

  It will be useful.

  Federico.

• The upgrade of the PIX firewall

  I currently have two firewalls Pix 515 (v4.4 and v6.2). I want to update the v4.4, but am unable to download the software from Cisco. Whenever I try to download using the link 'download pix software', it times out.

  I have already set up a tftp server and plan on the use of monitor mode to perform the upgrade. I already did a "write net:" to save the current configuration. " In addition, the original configuration remains intact, or they will be lost after the upgrade.

  Thanks in advance.

  Looks like you may have a problem with the download or the browser proxy. Try another host and/or browser and see if it works better.

  Since the PIX 4.4 software and versions later, you can go directly to any newer version of the software. To preserve your config, but it's always a good idea to back it up before an upgrade as you did. The config in the PIX is actually not get converted when PIX is restarted with the new software - what happens the first time you do a "write mem" under the new software, it is so important to remember to do as part of the upgrade process. You can then check the config freshly recorded against your configuration of backup for all differences. In addition, it is important to check the Release Notes before upgrading, but if you have a config PIX relatively simple it will probably be fine. One thing you want to do is migrate away from lines on access lists. Cisco is a utility that allows to convert them for you, and it does a very good job as long as your config is not too complex, so I might suggest to give it a try and see how it works for you. The downloadable version of this utility must be on the same page as other PIX software download, and there are versions for Windows and Sun Solaris.

  Good luck!

• banner for pix

  What is the command for creating a banner in 6.2

  6.3 I know, but I can't find 6.2

  Thank you

  Hello

  Unfortunately it is not a. Support for banners was introduced in version 6.3 of the pix software.

  HTH

  Jon

• 3DES throughput of PIX 520?

  Hello

  Anyone know what is the PIX 520 3DES throughput? (No VPN accelerator card)

  Thank you

  Hi Oneill,

  As PIX520 EOL, it took me a bit of searching to find it, so I hope this helps you...

  http://www.Cisco.com/warp/public/cc/PD/FW/sqfw500/prodlit/963_pp.htm

  Software and hardware encryption

  Version 5.0 (1), with the addition of the appropriate encryption key, provides encryption based on the software for THE (56-bit) and 3DES (168-bit), as support for the acceleration OF only using the PL2 existing (PrivateLink) map. Users can expect to see a minimum of 10 to 20 Mbps of throughput for 3DES connections and 30 to 40 Mbps of throughput for using encryption based on PIX software. Customers who use the card PL2 can expect to double their throughput OF. NOTE: The PL2 card does NOT support 3DES encryption. In addition, the low number for above mentioned 3DES throughput is for the 515 PIX with a 200 MHz processor, and the high number is for 520 PIX with a 350 MHz processor.

  Kind regards

  Abdelouahed

  -=-=-

• No password Group tunnel inside the backup of the ASA

  Hi did anyone know why group tunnel passwords have been removed from the config. See below

  IPSec-attributes tunnel-group TG_RAS

  pre-shared-key *.

  This means that if I try to restore the config I have a * as pre-shared key password.

  Is it possible to have the pre-shared key shown as encrypted text?

  Thank you very much

  Hello

  Make a ' writing NET tftp_server_ip:filename "and then open the file from the tftp server. It should be in a format that is not encrypted. Encryption is caused by the PIX software.

  Kind regards

  Arul

  * Rate pls if it helps *.

• Modem ADSL PIX501 and UK

  Is it possible to interface a PIX 501 directly to a UK ADSL modem? If so is it an example of configuration available. Is he a PIX software release pre - req?

  Hi Alan,

  What you are trying to achieve is possible, if you have an IP address assigned by your ISP for the ADSL Modem interface (i.e. If an IP can be attributed to your ADSL modem, if not then router solution is the way to go) then what you need to do is configure the PIX with PAT (Port Address Translation), in this way all your home addresses will result in 1 public IP (ISP ADSL Modem IP) address. I assume that your facility would be something like this:

  LAN - PIX501 - ADSL (MODEM) - ISP

  Here is an example in this example the PIX is directly connected to the ISP and the ISP assigns a unique public IP address for the PIX, which SHOULD be used on the external interface.

  Here is the configuration that will allow the PIX to use the same IP address on the external interface using the address to make PAT for inside network devices.

  (LAN(192.168.3.0/24) INSIDE_ROUTER(192.168.2.2/24) (inside_e1 192.168.2.1/24) PIX, PIX (outside_e0 199.199.199.2/30)---INTERNET

  PIX (config) # ip address outside 199.199.199.2 255.255.255.252

  PIX (config) # ip inside 192.168.2.1 address 255.255.255.0

  !

  PIX (config) # route outside 0.0.0.0 0.0.0.0 199.199.199.1 1

  PIX (config) # the road inside 192.168.3.0 255.255.255.0 192.168.2.2 1

  !

  PIX (config) # global (1 external interface)

  PIX (config) # nat (inside) 1 0 0

  The foregoing, the nat command specifies that all internal addresses use the pool of addresses configured in the global order for pool 1. The corresponding overall command, but doesn't specify a pool of addresses, but done refers to the external interface. One of the advantages of this method are that if the ISP is not statically assign you the public address, but it uses DHCP to assign the address, you n t need to worry about what the address is assigned finally on the external interface as the parameter of the interface causes the PIX to use the address currently assigned, if it s assigned statically or dynamically.

  Also, when you make changes (as above) do not forget to order 'clear xlate' and also command 'write the memory.

  You can find useful the following URL:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_62/config/bafwcfg.htm#37288

  I hope this helps your situation, let me know how you go.

  Thank you - Jay

• To use external DNS names

  I have a PIX 515 with two interfaces:

  inside: 10.100.100.x

  outside: 172.29.50.50

  Internet DNS domain: somecompany.com

  Local DNS domain: somecompany.local

  (The IP address have been changed to protect my network.)

  I have a web server inside my network (webserver.somecompany.local), which is at 10.100.100.100

  I configured a static as NAT:

  public static 172.29.50.51 (Interior, exterior) 10.100.100.100 255.255.255.255

  Internal users should use the address: http://webserver.somecompany.local while external users use http://www.somecompany.com.

  Is there a way to allow internal users to use http://www.somecompany.com?

  Thanks in advance.

  Doug.

  It depends on your version of PIX software, with the latest version, you can use the keyword 'DNS' in your 'static' statement

  This command will allow the PIX to rewrite DNS replay with your local IP address.

  With older versions of the software, you had the alias command.

  PIX # static HS

  static (inside, outside) 200.xxx.xxx.21 www 192.168.0.200 tcp www DNS netmask 255.255.255.255 0 0

  # Sh fixup PIX

  fixup protocol dns-length maximum 512

• PIX 515 and software version 6.3 (4)

  We have a PIX 515 (not 515E). Currently, we are running software version 6.2 (2). I was wondering if we can improve the software to version 6.3 (3) or 6.3 (4), or do we need to replace the hardware with PIX 515E?

  Also what should I do on my current PDM version 2.0 (2) if it is possible to upgrade the PIX to a 6.3 version?

  Thank you.

  You can run on the Pix515 6.34. It takes at least 16 MB of flash and 32 MB of RAM.

  If you use PDM, you will need to be updated also.

  Josh

• PIX firewall software

  Hi guys,.

  I am looking to download IOS ver 4,0000 for PIX 515E, but can't seem to find anywhere in the downloads/security section. The only version they have is 8.0.4.

  Anyone know where I could find all earlier versions?

  Thank you very much

  Elena

  Elena, when you go to download box, choose any version 8.0, then window right side you will see a text saying previous software release click on this hyperlink and it will take you to all versions including 7.x

  http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=8.0.4&mdfid=277072390&sftType=PIX+Firewall+Software&optPlat=&nodecount=2&edesignator=ED&modelName=Cisco+PIX+515E+Security+Appliance&treeMdfId=268438162&treeName=Security&modifmdfid=&imname=&hybrid=Y&imst=N&lr=Y

  but here's the direct link

  http://www.Cisco.com/cgi-bin/tablebuild.pl/PIX

  Concerning