Remote access to Airport extreme

Similar Questions

• ARE remote with Apple Airport Extreme router wireless

  Hi all! I'm controlling my DA5800 STR using the Remote ES app but neither my iOS device sees the receiver OR my Sony Android Tablet S. So I figure it must be the network set up. I use a cable modem Motorola connected to an Apple Airport Extreme via an ethernet cable. The receiver is connected to the router, as shown in the manual.

  I'm doing something wrong here?

  Thanks in advance for any help!

  Hello Sandiegodom,

  Please check the network settings on the receiver ARE and confirm that the 'external control' is active, as well as the "relief network" that will allow the application ARE the 'waking up' the unit from standby mode.

  Also check that your phone is connected to the same wireless network, and IP addresses of the phone and the receiver are in the same subnet / IP Range. UpNp must also be enabled in the settings of the router.

  If you have verifed that these settings are correct, then the question is perhaps with the router where it does not send data to the local discovery of uPnP network devices. A simple power reset or resetting the router will sometimes force the router to send back data and should fix the problem if that is the case.

• Cannot access the airport extreme with Airport utility

  Why doesn ' t my airport extreme appear in airport utility?

  Reset the AirPort Extreme > reset a FAQ of base station airport

  Then see if it is recognized in AirPort Utility.

• The Airport Extreme WiFi intermittent 2nd generation

  I'm having a weird problem with loss of WiFi on my Apple Airport Extreme.

  My 2nd generation that apple Airport Extreme Base Station began to close its WiFi broad signal several times.  It happens usually after 60 minutes or less works very well.  Power on and the new runs for awhile until it stops again the WiFi.  Green light normally forward either static rest without flickering to indicate data transfer, or it will just dark.  Sometimes it will turn off WiFi and then restart WiFi a few minutes later and appear to be good.  But mostly it just stops and I can, he extinguished/turned on to operate correctly with the WiFi again.

  Airport Extreme is connected by ethernet cable to my modem/router main fiber (which is a different floor home) and it is set to "Bridge" Mode  It worked without any problems and I did no changes to my system.  My ISP did update my modem broadband fiber a few weeks ago to a "Virgin Media Hub 3.0"I understand was made by Compal.»  It seems to work perfectly and I have no problems with speed download or reliability in wireframe.  I was away from home for about a week and was able to access my wireless IP camera remotely via my Airport Extreme with no problems.  The problem started almost immediately on my return, but, as I said, I did no changes to my network.  I have never had this kind of problem before with my Airport Extreme.

  I am running OS X Yosemite on an iMac that is connected by a cable ethernet to the Airport Extreme and seems to work very well even when WiFi is de-energized on the Airport Extreme.  Airport utility reports the airport as current firmware version 7.6.7.

  I used network utility, Fing, and it showed that my Airport Extreme has multiple IP addresses, which seem to conflict with the IP address for my three AppleTV.  I manually changed the IP addresses of the Apple TV to another IP address not conflicting, but Fing always shows that my Airport Extreme has three IP addresses and I still have the problem of WiFi.

  Any other suggestions on a probable cause of this problem or the best way to solve the problem would be much appreciated.

  Thank you!

  The question is the 2nd generation AE is now too old.

  I would say the power supply (external or internal) is dying.

  It service life is approximately 5 years... your must be 8 years old. so the solution is simple... buy a new one... or I'll tell... Newish...

• Impossible to use Time Machine on Airport Extreme

  Back in June, I brought a laptop HD work to save the laptop. It's something I have done 3 times a year, in addition to using Time Machine on my 1 TB Airport Extreme. Well, when I did that, I went from 'H Time Capsule' to 'Brian's Portable HD. Everything saved. No problem. It seemed.

  Unfortunately, I can no longer use Time Machine on the 1 TB drive. Every time as I try, I get "password to the server": Time Capsule". And the password I try does not work. Arrrggh.

  Is it possible to find the password lost at an Airport Extreme?

  Can or, if it's a no-go, I reset everything on it and start over?

  Thank you.

  Brian

  It would really help if you could provide the version of the operating system that you use on your laptop.

  The reason is that if you can access the AirPort Extreme using AirPort Utility, you can retrieve the "lost password" for the album Time Capsule, which could be the password wireless, could be the base station password, or it might be the disk password... it depends of how you implement the AirPort Extreme.

• Is it possible to remote access to files on airport time capsule without a great second computer mac at home?

  Hello!

  I read the articles on access distance to another mac, but what I need is to remote access to files on airport time capsule without a great second computer mac at home.

  Only Mac... Mac you will use for remote access to files on the Time Capsule... is necessary.

  Set up and use Back to My Mac

• Airport Extreme with guest network configuration

  Hello

  I have a two-storey house and want to spend an Airport Extreme on each floor.

  In technichal room I have my ISP and a witch (192.168.1.0) dhcp router

  There is also a switch and a patchpanel which I have connected my extreme two boxes to.

  Does anyone have a suggestion on how to implement it properly? I would like to have internal wich wpa2 network and a network of comments without password and of course I want to have the same ssid, etc. on each floor.

  Thanks in advance.

  Henning

  Does anyone have a suggestion on how to implement it properly?

  There's the rub.  Since you have a router supports DHCP and NAT services to the network 'upstream' extremes of the airport, the airports must be configured in Bridge Mode to avoid Double NAT error that occurs when you have more than one router on a network.

  Unfortunately, the network comments feature does not work correctly when the airport is in Mode Bridge connected to another router.  The 'main' or private network works OK, but 'guests' will not be able to access the Internet.

  The only way to do what you want would be to configure things wrong by...

  (1) connect to an AirPort Extreme to the switch and configure it as a router to "create a wireless network" using DHCP and NAT.

  (2) linking the second AirPort Extreme for the first AirPort Extreme... not to the switch... and implement the extreme second "extend using Ethernet.

  Since you will have a Double NAT on the network, there is no guarantee that things will not work properly. Sometimes you can get away with a Double NAT error on a simple network, but it can cause difficulties of communication between devices on the network and the difficulties with Internet connections as well.

  If you have a console online game and want to play interactively on the Internet, the Double NAT error will not allow this to happen.  Similarly, if you plan to use Back To My Mac or Port Forwarding for access over the Internet to remote devices, the Double NAT will allow these connections probably not happen.

  We do not recommend a Double NAT Setup, but we have some ideas on how to do it. There of probably no harm in trying the Double NAT configuration if you have the time and are willing to experiment to see if it peut work for you, I'm sorry, but there are no guarantees here.

• How to configure DynDNS for camera IP with Airport Extreme?

  Hello... I recently bought an airport extreme 6th gen.

  I have an IP camera installed on my cabin, which I would like to access remotely for security reasons.

  My internet provider does not have a fixed IP address, so I need to be able to access my camera, even if my IP address changes.

  I understand that I must install a Dyn DNS, but I can't seem to set it up on my airport extreme.

  Is it possible to do?  If not, is there any IP camera on the market that is completely compatible with Airport Extreme for remote access?

  DynDNS don't think you can do this with an Airport Extreme

  https://help.dyn.com/airport-and-time-capsule-with-dynamic-DNS/>

  If you have another computer in the cabin, you can then run a DynDNS update utility on this computer.

  If not, perhaps you should consider a different router for the cabin.  You could put the Airport Extreme in Bridge mode and still use it.

• Airport Extreme in Bridge Mode?  What did I want?

  I'm AT & T Uverse with Gigapower.  Until today I had 2 networks in my home, the AT & T router then the one I created on my Apple Airport Extreme.

  The tech told me that I can implement the airport just mirror or fill the AT & T network.  In this way all devices in the House are on the same network.  In the past, there are times where someone has been connected on the AT & T network, but wanted to print to the printer WiFi, which stood on the Airport network.  We must also be on the Airport network in order to access the iTunes account via the Remote App.  Only, it would be easier if everything was on the same network, and we did not have to worry about switching.

  I want to use Airport Extreme to give us better coverage downstairs in the House.  The AT & T router is in a closet on the floor.  The signal is not large in some rooms on the ground floor.

  How to make the Airport Bill as a Repeater for the AT & T network?  What is this called bypass surgery?

  Thanks in advance for your help and your big brain.

  Adam

  Yes. Plug your Airport Extreme in a spare Ethernet port on the router AT & T. open Airport utility, click on the Airport Extreme, select Edit, select network and the router Mode value: Off (Bridge Mode) and update. Your Airport Extreme is now part of the AT & T network.

  p.s. You need to connect a cable Cat 5 or Cat 6 Ethernet of the AT & T to the Airport Extreme router since they are in different places in the House.

• Mitsubishi ductless AC / MiniSplit KUMO CLOUD and Airport Extreme...

  Mitsubishi just came out with an 'easy' solution to allow remote access and control of your system from mitsubishi with your iphone or android...

  Unfortunately it can only connect to a router or wireless access point that has the "WPS" button on it.

  Airport Extreme supports the WPS feature at all?

  This is a link to the datasheet...

  http://USA.mylinkdrive.com/uploads/documents/5288/document/PAC-WHS01WF-E_Product _Data_Sheet.pdf

  I ordered the remote to install myself but try to align my 'how to' if I have an airport extreme.

  Or if I find a lower tech router with WPS function...

  Please note that Mitsubishi has chosen to compromise your network by using and encouraging a method of broken security (WPS) for their cloud of Kumo controller wireless.

  https://en.Wikipedia.org/wiki/Wi-Fi_Protected_Setup

  So for those who are interested in remote access to your unit ductless... beware.

  I am waiting for an official response from Mitsubishi, but I have little hope that they're going to fix anything.

• How to create a network redundant ISP failover using 2 Airport Extreme

  Hello friends,

  I have 2 different lines of rented ISP related to my Airport Extreme 2. Was curious to know if these 2 AEs can be interconnected somehow to create a network of ISP failover. Users on AE 1 traffic would be transparent reassigned to the AE 2 and vice versa, if corresponding ISP fails. When the access provider is in place, they will return to their AE in elementary school.

  Thank you.

  Not without a smart dual wan router. That is to say done good load sharing.

  Extreme is about as simple a router you can find... He has the absolute minimum of functionality.

  Users on AE 1 traffic would be reassigned transparent to the AE 2 and vice versa

  You can do this by using some manual intervention... a simple change of entry door is usually sufficient.

• How to use Airport Extreme with ethernet leased line

  Hello friends,

  I was wondering if Airport Extreme is a true router, can I connect gout ethernet of my leased line directly in its WAN port, rather than put the provided ISP router between the two? I have lived many positions and all seem to suggest the connection of a cable/dsl modem to the WAN port on the extreme. Not found any information where it shows the ethernet line rented directly linking in the Giga WAN port, without any 2nd device in the meantime.

  If it's possible, then I guess also what public IP provided PSI can be put into the WAN of AE interface. Can someone develop more on it and detail the steps of configuration? Given that EI has basic firewall NAT, I think it's doable, but can someone confirm please.

  Thank you very much.

  Temporarily, if you connect your computer directly to the Ethernet line, can you get a good connection Internet in this way?

  If so, then AIrPort Extreme could function as a router for you, but you are also likely to face a Double NAT error on the network. How well... or, even if... This might work cannot be known until try you it.

  If the computer cannot connect, then what is required of your supplier for the computer to connect and get Internet access?

• Can the Airport Extreme connect wireless to my wifi network?

  Hi all

  I have an Airport Extreme, which I use only for his Time Machine feature.  Best I can tell the only way he can connect to my wireless network is extending.  Is this correct?

  If I use it to extend my wireless network was is the negative impact (if any)?

  Thanks in advance.

  You can extend wireless or even join wireless to less the router that you connect to another router from Apple.

  If this is the case then it can work well if it is in the range... otherwise, you must plug the AE into the router principal by ethernet and put in place as a separate network wireless access point.

  Extend wireless is bad if you are linked to the main router wireless... which will cause huge slow down even if you are in a situation of apple router all.

• Apple Airport Extreme and new FIOS router - problem

  Hello, I have an Apple Airport Extreme 802.11n base station, which worked well with a Comcast router.  When you set up with Comcast router, I set the router to comcast to bridge and the Airport Extreme has done all the work as the main router. When I switched to Verizon FIOS today, I get the typical mistake of NAT double (that I did with the Comcast before configuring the router to Comcast to bridge).  However, the tech support guy FIOS said that was not an option, so he set up my Airport Extreme in bridge - router off mode mode.  This really live to the top incoming access using SSH, Timbuktu or the Apple screen sharing, given that I can't assign fixed IP addresses to the computers on my network and can not use the Airport Utility Network Port settings to open "pipes" for a particular computer.  In addition, I'm more comfortable using Airport Extreme, rather than things FIOS. Someone at - it other than enter Comcast suggestions?

  I did a search and didn't see a post on this in the discussion forum.  Thank you

  What is the brand and model of your router Verizon? Verizon provides you with administrator access to it to allow you to make changes?

• Is Airport extreme dual band

  I have a double router band nighthawk netgear as my base station to the floor and I put my Airport extreme downstairs as a wifi extender told me that if my airport extreme is only single of the band will slow down the network of hole. Is this true?

  We need the model number of your AirPort Extreme to tell you whether it is simple or double band. The model number is at the bottom of the airport... starts with an 'A' followed by 4 digits.  An example would be the A1143.

  Then, it might help to understand that Apple uses proprietary technology to Wireless "extend" a network that is designed to allow only Apple routers extend the signal of another router from Apple.

  When wireless routers expand a network, there is always a loss of about half of the potential speed on the network. Nature of the beast with a wireless extension.  This loss can be avoided if the routers connect using a wired Ethernet connection.

  You don't specify how the airport will connect to the Netgear network, so it would be useful that you could clarify on this.

  It is very unlikely that an airport could not Wireless extend the signal from a third-party router. If your airport is an AirPort Express Terminal, it can probably 'join' the Netgear network so that it will work for AirPlay or allow a remote USB printer to connect.

  But the Express (or extreme, if that's what you have) not connect "extend" the network when he "joins", then wireless near the airport unit will always be all the way back to your main router.

  So, it might be a good idea to check the settings of the Express using AirPort Utility to find out exactly what it is and is not on your network.