Remote host said: 554 rejecting forbidden attachment [BODY]

Similar Questions

• Unable to ping the remote host IP address

  I have a home network with 2 desktop computers, printer, TV and BlueRay attached.  The PC is both XP and members of the same workgroup.  I can't get the connectivity between the PC 2.  With 1 PC, I ping successfully all connected devices, with the exception of 2 PC.  2 PC, I ping equipment successfully connected, including 1 PC...  I get the same information using a different router and a different network on 2 PC card.

  I tried the following steps of the Article 314067:

  1. check on two PC's TCP/IP configuration.  Result: good on both PCs.

  2. use the ping tool to test connectivity.

  • Ping the loopback address.  Result: good on both PC
  • Ping to the IP address of the local computer.  Result: good on both PC
  • Ping the IP address of the default gateway.  Result: good on both PCs.
  • Ping to the IP address of the remote host.  Result: bad on PC 1, good on PC 2
  • Ping other IP addresses on the network.  Result: good on both PCs.
  • Ping the host name of the other PC.  Result: bad on PC 1, good on PC 2

  Article:

  If the ping command fails, the remote host may not be responding, or there may be a problem with the hardware of network between computers. To the rule

  on a remote host does not respond, use Ping again to a different remote host.

  If you cannot use Ping successfully at any time, verify the following configurations:

  1. Make sure that the IP address of the local computer is valid and that it is correct on the

  Tab general of the Internet Protocol (TCP/IP) properties dialog or box when it is used with the Ipconfig tool.  Result: good on both PC

  Make sure that the default gateway is configured and that the link between the host and the default gateway works. For the purposes of troubleshooting, make sure that this gateway by default is configured. You can configure multiple default gateways, gateways after the first gateway is used only if the IP stack determines that the original gateway is not working. Diagnosis is to determine the State of the first configured gateway. Therefore, you can delete all the other gateways to simplify your task.  Result: good on both PC
  Make sure that Internet Protocol security (IPSec) is not enabled. According to the IPSec policy, Ping packets may be blocked or may require security. For more information about IPSec, go to method 7: Verify Internet Protocol security (IPSec).  Result: good on both PC

  Thanks for your suggestions you may have.

  Hello

  Firewall such as Norton, McAfee etc can cause a loss of network connectivity, even when the network is correctly configured. Try disabling the firewall on both computers to see if the ping works.

  Tricky

• TAC +: TCP/IP open to 10.20.17.2/49 failed - connection has expired; remote host does not

  GANYMEDE + configured on the router and the router is in ACS.  I can ping from the ACS, but the router cannot establish a connection to authenticate users.

  AAA server Ganymede group + hq_acs-1

  Server 10.20.17.2

  Ganymede IP source-interface GigabitEthernet0/0

  !

  AAA authentication login default group Ganymede + local

  AAA authorization config-commands

  AAA authorization exec default group Ganymede + local

  AAA authorization commands by default group Ganymede + local 10

  AAA authorization commands 15 default group Ganymede + local

  nested AAA accounting

  AAA accounting newinfo periodic update 60

  AAA accounting auth-proxy default start-stop Ganymede group.

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 15 by default start-stop Ganymede group.

  AAA accounting network default start-stop Ganymede group.

  Default connection accounting AAA power Ganymede group.

  AAA accounting system default start-stop Ganymede group.

  AAA accounting resource by default start-stop Ganymede group.

  BigTree_3945 #sh ip int br

  Interface IP-Address OK? Method State Protocol

  GigabitEthernet0/0 10.4.3.1 YES NVRAM low low

  GigabitEthernet0/1 10.12.10.26 YES NVRAM up up

  Serial0/2/0 unassigned YES NVRAM low low

  Serial0/2/0.602 10.12.15.10 YES NVRAM low low

  11:08:13.673 Apr 13: MORE: Queuing AAA request authentication 79 for the treatment

  11:08:13.673 Apr 13: MORE: treatment demand beginning 79 authentication id

  11:08:13.675 Apr 13: MORE: authentication start package created for 79 (cisscdb)

  11:08:13.675 Apr 13: MORE: using the 10.20.17.2 Server

  11:08:13.675 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: started 5 sec timeout

  11:08:18.676 Apr 13: HIGHER (0000004F) / 0/NB_WAIT/1BDD9C34: expired

  11:08:18.676 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: expired, cleaning

  11:08:18.676 Apr 13: HIGHER (0000004F) / 0/1BDD9C34: the package of treatment response

  11:08:25.834 Apr 13: MORE: Queuing AAA request authentication 79 for the treatment

  11:08:25.834 Apr 13: MORE: treatment demand beginning 79 authentication id

  11:08:25.834 Apr 13: MORE: authentication start package created for 79 (cisscdb)

  11:08:25.834 Apr 13: MORE: using the 10.20.17.2 Server

  11:08:25.834 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: started 5 sec timeout

  11:08:30.836 Apr 13: HIGHER (0000004F) / 0/NB_WAIT/1BDD9C34: expired

  11:08:30.836 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: expired, cleaning

  11:08:30.836 Apr 13: HIGHER (0000004F) / 0/1BDD9C34: the package of treatment response

  11:08:43.689 Apr 13: TAC: using default Ganymede groups ' Ganymede"list."

  11:08:43.689 Apr 13: TAC +: opening TCP/IP 10.20.17.2/49 Timeout = 5

  11:08:51.057 Apr 13: MORE: Queuing AAA request authentication 79 for the treatment

  11:08:51.057 Apr 13: MORE: treatment demand beginning 79 authentication id

  11:08:51.057 Apr 13: MORE: authentication start package created for 79 (cisscdb)

  11:08:51.057 Apr 13: MORE: using the 10.20.17.2 Server

  11:08:51.057 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: started 5 sec timeout

  11:08:54.692 Apr 13: TAC +: TCP/IP open to 10.20.17.2/49 failed - connection has expired; remote host does not

  11:08:54.692 Apr 13: MORE: Queuing AAA accounting request treatment 76

  11:08:54.692 Apr 13: MORE: treatment of the accounting application id 76

  11:08:54.692 Apr 13: MORE: sending AV task_id = 332

  11:08:54.692 Apr 13: MORE: sending AV timezone = EDT

  11:08:54.692 Apr 13: MORE: AV = shell shipping service

  11:08:54.692 Apr 13: MORE: sending AV start_time = 1334329734

  11:08:54.692 Apr 13: MORE: sending AV priv-lvl = 15

  11:08:54.692 Apr 13: MORE: sending AV cmd = show logging

  11:08:54.692 Apr 13: MORE: request for accounts created for 76 (n20j03t)

  11:08:54.692 Apr 13: MORE: using the 10.20.17.2 Server

  11:08:54.692 Apr 13: HIGHER (0000004C) / NB_WAIT/1/20FD90EC: started 5 sec timeout

  11:08:56.058 Apr 13: HIGHER (0000004F) / 0/NB_WAIT/1BDD9C34: expired

  11:08:56.058 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: expired, cleaning

  11:08:56.058 Apr 13: HIGHER (0000004F) / 0/1BDD9C34: the package of treatment response

  11:08:59.693 Apr 13: HIGHER (0000004C) / NB_WAIT/1/20FD90EC: expired

  11:08:59.693 Apr 13: HIGHER (0000004C) / NB_WAIT/1/20FD90EC: expired, cleaning

  11:08:59.693 Apr 13: 1/HIGHER (0000004C) / 20FD90EC: the package of treatment response

  BigTree_3945 #.

  The AAA Client IP address	10.4.3. * 10.12.15.10
  Key
  Group of network devices	Test NJT AccessLink (Not assigned)
  Authenticate using	GANYMEDE + (Cisco IOS) RADIUS (Cisco Aironet) RADIUS (Cisco BBSM) RADIUS (Cisco IOS/PIX) RADIUS (Cisco VPN 3000) RADIUS (Cisco VPN 5000) RADIUS (IETF) RADIUS (Mount) RADIUS (Juniper) RADIUS (Nortel) RADIUS (Sepi)
  Connect GANYMEDE + single AAA Client (stop recording in accounting in case of failure).

  The 10.12.10. range * is listed under the HQ site.

  Your help is greatly appreciated.

  You said that you can ping the router ACS, have you tried the GigabitEthernet 0/0 interface packages (that is those THAT GANYMEDE + will attempt to use, given the configuration you have posted) supply?

  What is the network path between the router and look like ACS (IE, a firewall, NAT, etc.)?

  Can you connect to port 49 to the IP address of the router GBA, GigabitEthernet 0/0 of supply packages?

  Using VRF?

  Which version of IOS?

• An existing connection to be closed by the remote host.

  Since last week, I can't keep a connection to the server of vatsim or acars for virtual pilots micro flight simulator will for more than five minutes. the error message is that an existing connection had to be closed by the remote host

  not an expert of anymeans and all the answers I got on the net are well above my paygrade.

  Hi dva8377,

  Here are two additional methods you can try.

  1: Restart the computer by using a clean boot of the method

   

  When you start Microsoft Windows, other software may start with the operating system. These programs may include antivirus software and system programs that may interfere with the game. When you perform a clean restart procedure, you prevent these programs from starting automatically.

  Reference:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Method 2: Bypass the router

   

  If you connect to the Internet using a router, there may be a problem with the configuration settings, which requires that the updated settings. To determine if a network connectivity problem is caused by a bad configuration or a problem affecting the router, try bypassing the router by connecting your computer directly to the modem. Remember that this test will only check that the router is configured correctly. If the game connects to the Internet without problem when you bypass the router, plug the router immediately and contact the manufacturer of the router or your ISP for help configure the router correctly.

  Note: Ensure that you switch your computer to normal startup mode after completing the troubleshooting steps. Steps are available in the article above.

  For more information, see: http://www.microsoft.com/Products/Games/FSInsider/tips/Pages/default.aspx

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Diagnostics network ping to the remote host, but has not received a response

  I'm trying to figure out if there is a problem with just my laptop not wanting to connect to a local free WiFi, so any help is appreciated. He worked two days ago only to stop abruptly last night.

  Windows Network Diagnostics comes back with the error message "Can not contact www.microsoft.com (65.55.12.249)" and "diagnostic network ping to the remote host, but has not received a response.

  The only repair option it evokes is ' reset NIC 'wireless network connection ' '.

  I can always connect to WiFi using my iPhone, and even a connected laptop computer work Companion. Yet once, if this can be fixed on my end, any help would be appreciated.

  Hello BrenJones,

  Thanks for posting back. DNS servers are controlled by your ISP. I communicate with your Internet service provider and confirm that you have the good DNS for your network.

  Hope this helps J

  Adam
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Remove a remote host from monitoring Infrastructure

  How can I go about removing a host of infrastructure monitoring?  If the host has its own fglam, I was able to disable the agent simple, remove fglam, etc..  In this case, I see no option to turn off monitoring, or withdraw completely from the remote host monitoring.

  In the screenshot below. Let's say that I simply wanted to see information of the rd-r220-01.  But I always wanted my central collector collect statistics on all remote hosts.

  See you soon,.

  Seth

  If I wanted to stop monitoring of the vmebizjmc of the host, I'll stop the WindowsAgent. In the screenshot you can see other officers running from the host even where a foglight agent Manager is running. I can't stop foglight agent manager.

  

  David Mendoza

• How to start the tunnels without the need of ping to a remote host

  That's the big question!

  How can you tunnels without need to ping to a remote host in the target network? Our clients get hung on a regular basis because of this problem. 10 points for the first answer!

  Hello

  You can configure KeepAlive on end VPN.

  For example

  On PIX

  ISAKMP keepalive 2 30

  On IOS

  ISAKMP crypto keepalive 10 periodicals

  If it does not solve that and you need some kind of traffic you can configure NTP on the link VPN (source of the private interface it is so interesting traffic for VPN).

  HTH

  Sangaré

• Whenever I try to download I get this error message "a socket operation was attempted to an unreachable network. "This means that the local software knows no route to reach the remote host.

  Hi all

  I use windows 7. whenever I try to download I get this error message "a socket operation was attempted to an unreachable network. "This means generally that the local software knows no route to reach the remote host" what does that mean?  help solve this problem. Thank you '.
   
  Original title: proxy error

  Hello

  The question you posted would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en-us/categories

  Hope this information is useful.

• Existing connection had to be closed by the remote host

  Need help with this error
  I have a dev and a uat environment.
  I have a small form that I use as a method to call a web service. Essentially, the form contains a web service URL text box.
  If I call the shape on the dev and pointer to the service web dev, it works.
  If I use the form on uat and point the service web uat it works.
  If I use the form on UAT and call the web service on dev, it works.
  However, if I use the form on the dev and point the web service uat I get this error:

  In the Application Server error ' / '. An existing connection was to be closed by the remote host Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and its origin in the code.

  Exception details: System.Net.Sockets.SocketException: An existing connection was to be closed by the remote host

  Source error:

  The source code that generated this unhandled exception can only be shown when compiled in debug mode. To do this, follow one of the below steps, then request the URL: 1. Add a "Debug = true" directive at the top of the file that generated the error. Example: <%@ Page Language="C#" Debug="true" %> or: (2) add the following section to the configuration file of your application:                 Note that this second technique, all the files in an application to be compiled in debug mode. The first technique will make only this file to be compiled in debug mode. Important: Running applications in debug mode causes a memory/performance load. You must ensure that an application has debugging disabled before deploying to the production scenario.

  Stack trace:

  [(0 x 2746) SocketException: an existing connection was to be closed by the remote host] System.Net.Sockets.Socket.Receive (Byte [] buffer, Int32 offset, Int32 size, SocketFlags socketFlags) + 73 System.Net.Sockets.NetworkStream.Read (Byte [] buffer, Int32 offset, Int32 size) 131 [IOException: unable to read data from the transport connection: an existing connection was to be closed by the remote host.] System.Net.Sockets.NetworkStream.Read (Byte [] buffer, Int32 offset, Int32 size) + 294 System.Net.PooledStream.Read (Byte [] buffer, Int32 offset, Int32 size) + 26 System.Net.Connection.SyncRead (request of HttpWebRequest, Boolean userRetrievedStream, Boolean probeRead) + 297 [WebException: the underlying connection was closed: an unexpected error occurred during the reception.] System.Net.HttpWebRequest.GetResponse () + 5399741 _Default.btnTestUpload_Click (Object sender, EventArgs e) + 532 System.Web.UI.WebControls.Button.OnClick (EventArgs e) 111 System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument) + 110 System.Web.UI.WebControls.Button.System.Web.UI.IPostBackEventHandler.RaisePostBackEvent (String eventArgument) + 10 System.Web.UI.Page.RaisePostBackEvent (IPostBackEventHandler sourceControl, String eventArgument) + 13 System.Web.UI.Page.RaisePostBackEvent (NameValueCollection postData) + 36 System.Web.UI.Page.ProcessRequestMain (includeStagesBeforeAsyncPoint, Boolean, Boolean includeStagesAfterAsyncPoint) 1565

  Version information: Microsoft .NET Framework Version: 2.0.50727.4234; ASP.NET Version: 2.0.50727.4223

  Any ideas?

  Hello

  I suggest you for this post in the appropriate section of the form of MSDN

  http://social.msdn.Microsoft.com/forums/en-us/categories/

  I hope this helps.

• Remote host IP SLA ping by tunnel VPN with NAT

  Hi all

  I did some research here, but don't drop on similar issues. I'm sure that what I want is not possible, but I want to make sure.

  I want to monitor a remote host on the other side a VPN. The local endpoint is my ASA.

  The local INSIDE_LAN traffic is NATted to 10.19.124.1 before entering the VPN tunnel.

  Interesting VPN traffic used ACL card crypto:

  access-list 1 permit line ACL_TUNNELED_TO_REMOTE extended ip host 10.19.124.1 192.168.1.0 255.255.255.0

  NAT rules:

  Global (OUTSIDE) 2 10.19.124.1 mask 255.255.255.255 subnet

  NAT (INSIDE_LAN) 2-list of access ACL_NAT_TO_REMOTE

  NAT ACL

  access-list 1 permit line ACL_NAT_TO_REMOTE extended ip 172.19.126.32 255.255.255.224 192.168.1.0 255.255.255.0

  This configuration works very well for traffic from hosts in 172.19.126.32 255.255.255.224 is 192.168.1.0 255.255.255.0.

  However, I like to use "ip sla" on the SAA itself to monitor a remote host with icmp ping 192.168.1.0. This would imply NATting one IP on the ASA to 10.19.124.1, but I do not see how to do this. None of the interfaces on the SAA are logical, to use as a source for this interface.

  Thanks for ideas and comments.

  Concerning

  You are absolutely right, that unfortunately you won't able to NAT interface ASA IP address. NAT works for traffic passing by the ASA, don't not came from the SAA itself.

• Copy Clone VM on the remote host?

  We currently have a Vcenter configuration limited to 3 guests.  I am creating a system for disaster, assuming that our main centre of recovery should fail.

  So, I need to program a clone of the VM are held every week - but then I need to copy this clone to a remote host which is not in the same data center, although it IS on the same network.

  Is there a way to achieve side manually remove a host to Vcenter and adding remote host (4th) whenever I want to copy?

  If I copy the clone on an external drive, I have to copy it again to the remote host.  It is 2 instances of copy on the network and which can last for hours.

  I want to reduce it to a single copy and perhaps even automate it with a script, but I don't know everything that the CLI in ESXi.

  Any ideas are appreciated.

  Understandable, I thought you wanted to just copy of VMDK but a clone first takes a snapshot of the virtual machine. This removes the lock on the base VMDK. ESXi can run rsync, but it is not supported. It is perhaps a bit over your head because you have no experience with Linux.

  http://www.virtuallyghetto.com/2011/02/how-to-compile-statically-linked-rsync.html

  What you could do is however if sure the source host and destination have access to the same storage. Then plan a clone to the virtual machine, but leave it turned off permanently. In the case of DR, on the other host, go to the data store, select the virtual machine folder, right-click the .vmx and say file added to the inventory. You can then restart it on another host. Or the DR host only has local storage?

• Unable to connect to the MKS: the certificate of the remote host has these problems:

  Hello

  We have a host of ESXi 4 cluster running any vSphere 4.1.  Recently, I started to upgrade to update 2 and all the additional fixes.  After the upgrade of the vCentre server to the latest version (or maybe before I can't noticed) an of are hosts began to show the following error whenever I tried to connect to the console of any guest on this host.

  Unable to connect to the MKS: the certificate of the remote host has these problems:

  It lists any problems at all and no error display in the event log that it simply does not work.  I had a prod around the internet and found nothing.  I then rebuilt the host to exclude and the problem remains.

  Any help would be much appreciated.

  Thanks in advance

  David

  If you can connect to the Console remotely using VMware Infrastructure (VI) Client connected directly to the host, take a look at vmware KB to connect to a remote virtual machine fails with the error: the certificate of the remote host has these problems

  but more generally - remove host to vCenter inventory and then add the host to the back, take a look at opening in the console of the virtual machine after a new installation of ESXi or ESX fails with the error: the host certificate chain is not complete and could not connect to the MKS: the certificate of the remote host has these problems

• Error during communication with the remote host when you create the new virtual machine

  I'm under 7 ESX servers on IBM Blade H22 there is a mistake to invite while I create a new virtual machine

  on the vcenter Server

  At the end of 30-35 minutes, it gives an error

  "Error during communication with the remote host"

  The existing machines are working well... I tried to create virtual machines to other ESX servers as well

  but the same question. I also tried to make the clone of existing machines, but without success

  Can anyone help?

  You rescan the LUNS once?

  You've restarted the management agent?

  You've restarted the vpxa?

  If this isn't the case, please perform the step above and check out them.

• Problems connecting to the remote host via FTP from DreamWeaver

  I have problems to connect to my remote host in DreamWeaver.  I can connect via the Client File Zilla and was able to connect until my hard drive crashed.  Now w/new drive, I get an error msg. I tried to create a new site, which connets when I test the connection, but when I go to view the files, a dialog box appears saying "(cannont get info dossier distant, accès refusé, etc) I tried selecting the different settings and combines following parameters: use firewall, secure ftp, ftp passive mode." Don't know what else to try at this point. I have WIN XP, Adobe Creative Suite CS3.  I'd appreciate any help, thanks!

  OK - it's good. I noticed that your host directory contains only the character ' / ' and that could be the source of your problems.  What happens if you remove that, just leave this field blank?

• "To connect to the remote host" is disabled

  Hello

  We have recently updated CS4. I imported all my old connections without problem.

  My boss recently asked to show him how to download files on a site. Configure the site as usual on his machine, but where I can click on my 'Connect to remote host' button and all the server files, see my boss button is disabled and displays a message about the configuration first the control version.

  We do not want to do that, only to access the server, as we have done before. Version control can be disabled? Or is it a different problem?

  Thanks in advance for any help.

  Gareth

  You have the icon poorly selected in the files Panel. See the following screenshot: