Remote Office losses periodically connection

Similar Questions

• Remote site 2 Internet connections...

  I have a remote office that currently connects to a data center Central via the VPN Site to Site.  I get a 2nd internet connection like a fall back to the remote desktop.  How to configure the Site to Site VPN working properly so that if the main internet connection goes down, the site switches to the secondary?

  On internet connections remotely come from different providers so that they have completely different blocks of public IP addresses.

  Central

  ASA 5520 8.0 (4)

  GIG 0/0 public IP

  Remote

  ASA 5520 8.4 (1)

  GIG 0/0 public IP

  Public IP address of concert 0/3 (2nd internet)

  On the end of HQ you must enter the new IP address of the ISP (for the remote site) as secondary peer.

  On the remote end, you must add SLA so that traffic will be redirected on the second link incase of primary failure.

  Search the forum you will find many Ref assignment to this scenario. Here is one...

  https://supportforums.Cisco.com/message/3452739#3452739

  HTH

  MS

• Connection of remote offices SPA3102

  My boss just bought two SPA3102 VoIP routers in an attempt to set up a VoIP connection to a remote office, thus avoiding expensive international calls.  I'm looking for advice on setting up.

  This is the ideal configuration, we're after.  Box, it is in the seat, and it is connected via the RTC port on a phone line (in fact the PBX).  His IP address is 192.168.32.8 (we are without using the routing of each box function, then the two boxes are connected to the network via the WAN port, with the side LAN not used at all).  Any incoming call on the telephone line must be connected directly on the phone connected to the box of two.  There is no phone connected to the box one.

  Box 2 is in remote desktop. For testing purposes, its IP address is currently 192.168.32.9.  He got a telephone connected to the telephone port, and the PSTN port is connected to a standard telephone line.  We want the phone to use the RTC line by default, but if the user dials 9 then, we wish the appeal directed to the PSTN line on box a (i.e. PBX.), where it can dial into a PBX it seeks.

  The offices are connected by a virtual private network, so there is no NAT anywhere to worry.

  I have a problem in this place, what with the instruction light manual and confusing options, so any help much appreciated!

  Here are the settings I've worked. I have omitted some.

  Head office

  WAN configuration:

  Connection type: static IP address

  Static IP: 192.168.32.8

  Subnet mask: 255.255.255.0

  Enable WAN Web server: Yes

  Line 1:

  Activate the line: no

  PSTN line:

  Activate the line: Yes

  Use outbound Proxy: no

  Register: no

  Call without Reg: Yes

  Call for years without Reg: Yes

  Numbering plan 1: (P1[email protected] >)

  (causes the call to transfer to the other box after a delay of one second)

  Enable VoIP to PSTN Gateway: Yes

  PSTN to activate the VoIP gateway: Yes

  PSTN through line 1 ring: no

  PSTN response time: 0

  PSTN Ring through delay: 0

  Remote Desktop box:

  WAN configuration:

  Connection type: static IP address

  Static IP: 192.168.32.9

  Subnet mask: 255.255.255.0

  Enable WAN Web server: Yes

  Line 1:

  The line activation: Yes

  Register: no

  Call without Reg: Yes

  Appeal of ABS without Reg: Yes

  Auto RTC backup: Yes

  Dial plan: (0 x<:@gw0>|) <>xx. <:@gw0>| <7:192.168.32.8:5061>)

  (This operation transfers the call to the seat on numbering 7 9 box gets an outside line, any number beginning with 0 is also formed through the PSTN line)

  PSTN line:

  Activate the line: Yes

  Enable VoIP to PSTN Gateway: Yes

  PSTN-to-VoIP gateway enable: no

  I have a problem on the left: calls to the phone remotely (both by the PBX and telephone line remote) are very quiet.  I played with the settings of Gain PSTN SPA to compensate, but I set the remote zone to its maximum of 12 and it is still too quiet, so I think that there is a problem elsewhere.

• Remote office - network level authentication

  Hello people, hope you can help!

  I have a laptop running vista professional and a desktop running vista ultimate.  On my desk, I activated remote desktop access and can rdp on the desktop from the laptop when the median option button is selected "allow connection of computers running any version of office to distance"... however... I obviously want to use network level authentication to be sure that I can access the office using my connection wireless laptops.

  When I try to do, I get the usual message, saying that "the remote computer requires network level authentication, that my computer does not support.    Curiously, when I try the other direction (from the desktop to the laptop), I have access! How is it?  I checked the windows features that are installed and they seem to be the same...

  Hello again,

  I double checked everything and both machines as set identical upward (as far as RD is concerned).  Both machines now have a user account called RemoteDesktop with a password, the two machines are set to "Notify me" and that the two computers are on the same workgroup.  Everything seems very strange to me.  If one of the PC did not support NLA, then it should not work at all, so it makes no sense that it works one way and not the other.

  That being said, What are the risks of a lower level running on a home network? The network is secure (or as secure as possible never) so what are the differences between the two settings?

  On your LAN House I would be worried about this. Its pretty hard to fake an address on the network under your control especially if your behind a router (with firewall function) and your wireless network is secured. I would, however, high encryption necessary and always warn the client for a password, sign in.

  http://theillustratednetwork.MVPs.org/RemoteDesktop/RDP6ConfigRecommendations.html#host

  FWIW, I regularly connect to desktop computer XP Pro to my wife and a Windows Home Server with Remote Desktop [DRC] a computer laptop Vista Ultimate or Win7 RC1 and Ubuntu. None of those taking support NLA mode server host/DRC. The Ubuntu laptop does not support the NLA in client mode DRC.

  That said, is the customer who cannot not configured like that? I believe that this is the default condition.

  http://theillustratednetwork.MVPs.org/RemoteDesktop/RDP6-09.jpg

  Also, just for the sake of the information that the failing client shows the extent of the support NLA. The built-in client for Vista should indicate this.

  http://windowshelp.Microsoft.com/Windows/en-us/help/ea4680d1-6962-463b-B29B-351efa676f9e1033.mspx

  I assume that your market SP1 or SP2 on the Vista client, which is a failure and have not tried to download and upgrade the remote desktop client.

  There is also this lengthy thread which can be interesting. Not exactly your question but interesting nonetheless. Bottom line is to make sure that the time is correct on all machines. There is also a procedure to remove the server/host certificate which you could do a test.

  http://social.answers.Microsoft.com/forums/en-us/vistanetworking/thread/4ab6c1ba-13ed-4b0a-b5ba-601e2b0a28d7

  MS - MVP Windows Desktop Experience, "when everything has failed, read the operating instructions.

• Implementation of remote offices, VMware ESXi

  Hi people, I hate you bug with what he could have been asnwered before, but I couldn't find an asnwer very clear here. Any help/advice is much apprecaited. So, here's the deal:

  We plan blown full virtualization (Server + VDI) to our datacenter and 3 remote sites. Data Center (HQ) and 1 remote office are located in Europe, 1 in North America and 1 Office in Hong Kong. All remote sites are with about 5 to 10 local non computer users. HQ has about 90 users and staff. Clearly, we want to put everything in place so that it can be managed on the Wan. We will make IPsec VPN site-to-site with each remote site through Cisco ASA and ISR routers/appliences.

  In HQ, we implement the Server Blade HP (chasis c7000) of several ProLiant G7 and EMC Clariion CX4 storage.

  For remote offices, we plan to have a local server (2 CPUs) and local storage. Internet connections are good DSL, but nothing complicated. On the road, we could look at MPLS in the light of the video and voice conference, but for now it's off the table. Because we want to deploy VDI in remote offices, we want to have clones the on local servers so that they are independent of WAN. We run a file sharin, DC, print server in terms of orders OS Server mainly.

  1. How is back-up to be managed from remote desktop to virtual offices at Headquarters? You can just save changes/deltas or is it always?

  2. what type of products VMware, we need in remote offices? VSphere Standard would do for everything what we need (remote management, backup remote VM etc.)?

  3. is it possible to have remote users forwarded to use their VD through the WAN of local server failure? Software that manages this part?

  4 any other recomendatiosn or best tips in our case here?

  Thanks again for any advice you have as we are very pleased to start this, but sure looks like a lot of work... and a few uncertainties.

  Jim

  Hello

  1. How do you distribute patches and OS updates to the remote VDs via WAN?

  You can use AUVS to install packages in the comments. In this way, everything is done on the spot.

  2. with a ThinApp structure in a VDI infrastructure how do you deliver applications, their patches to remote desktop (stream or MSI or?)? You have to have ThinApp servers etc. at the remote office or what is really the best way to handle this?

  ThinApp is a bit different and has their servers for the deployment of ThinApps. I think you should transfer as you ThinApps the patch... You can ask this question in the forums ThinApp.

  3. does anyone know a really good guide to set up an "office in a box" and it deployment?

  I have unfortunately seen documents for internal use. However, ones I've seen are usually at least 1 usually 2 boxes 2U with necessary storage locally or on a NAS with at least Gigabit switch. Usually, I suggest at least 2 boxes depending on the load. Ideally something easy to carry and move... If there was a 2 or 4 blade blade chassis, which would be the ideal...

  All licenses is managed at the Headquarters Office "in a box" being shipped to the remote desktop that is almost ready to go. A few tweaks remote and viola, you have the office. Don't forget to leave you an administrative VM on a VPN tunnel to your desktop to the remote location.

  Worst case scenario involves some generic desktop computers at HQ for all applications that do not need local data.

  4. licenses for virtual desktops (VMware View) must be purchased by the local office, or by given headquarters he is managed by vCenter HQ and the fact that it is on another continent?

  It's really up to you. But if it was me I would centralize management and "Chargeback" with the Agency.

  Best regards
  Edward L. Haletky VMware communities user moderator, VMware vExpert 2009, 2010

  Now available: url = http://www.astroarch.com/wiki/index.php/VMware_Virtual_Infrastructure_Security'VMware vSphere (TM) and Virtual Infrastructure Security' [/ URL]

  Also available url = http://www.astroarch.com/wiki/index.php/VMWare_ESX_Server_in_the_Enterprise"VMWare ESX Server in the enterprise" [url]

  Blogs: url = http://www.virtualizationpractice.comvirtualization practice [/ URL] | URL = http://www.astroarch.com/blog Blue Gears [url] | URL = http://itknowledgeexchange.techtarget.com/virtualization-pro/ TechTarget [url] | URL = http://www.networkworld.com/community/haletky Global network [url]

  Podcast: url = http://www.astroarch.com/wiki/index.php/Virtualization_Security_Round_Table_Podcastvirtualization security Table round Podcast [url] | Twitter: url = http://www.twitter.com/TexiwillTexiwll [/ URL]

• VI on a BladeCenter S for remote offices

  Hi everyone, it's a matter of design because I don't know much about BladCenter S.

  After reading this article, I become curious of this technology (http://it20.info/blogs/main/archive/2008/11/14/162.aspx) because it really can solve some problems, especially in remote offices.

  My questions are:

  (1) is the redundant eth switch? Article that I linked above, it seems that it is but to read the IBM documentation looks that all EPF blades are related to bay1 only, so only one switch eth (which would make not much sense);

  (2) is the internal memory, support for vmware? Could not find information on that, nor what hw config is required to share LUNS with blades;

  (3) is it possible to have 4 network adapters and interfaces 2 sas (from FC interfaces for it matters) without developing the blade server? I can't expand the blade increases the number of cards you can add but then each blade will take twice as much to place in the chassis, which is not good in a small bladecenter as the S

  I suppose to use HS21 XM blades just like I would on another chassis. Ibm documentation I found here (http://www.redbooks.ibm.com/abstracts/sg247523.html) and here (http://www.redbooks.ibm.com/abstracts/sg247682.html?Open) was very detailed, but confused about what I mentioned in my questions.

  Yes, ETH that a switch can be used, but then you get only half of the network connections.  Each blade is divided between the i/o modules, so if you have expansion for the blades ethernet card, and only have 1 switch, and then you get only half of the available network adapters.

  The IBM SAS HBA card is in the HCL: http://www.vmware.com/resources/compatibility/search.php?action=search&deviceCategory=io&productId=1&keyBasic=ibm+sas+&maxDisplayRows=50&key=ibm+sas+expansion&release%5B%5D=-1&datePosted=-1&vid=&did=&svid=&ssid=

  And Yes, I believe the extension ethernet 2 ports and the sas of maps extension and in a format that can fit into the PCI - X slots without the blade who need to take two slots, according to the guide.  I'm sure your IBM representative can go over this with you as well.

  -KjB

• Loss intermittent connectivity... Airport express router or modem problem?

  Airport express intermittent loss of connectivity?

  Not much information to go here.

  Please provide at least the following details:

  • What exact model of the AirPort Express model do you have?
  • What is an intermittent loss of connectivity? The Express, iPhone, another thing?
  • This working before and just started happening OR if this has always been a problem?
  • Did you do the upgrades of firmware or software recently, when this started to happen?
  • What have you tried so far, to solve this problem?

• Loss of connectivity

  Loss of connection to the internet even if the other computer in our home group has connection

  Hello

  1. what version of Windows are you using?

  2. you receive an error message?

  3. have you made changes on the computer before this problem?

  Please visit the following link.

  Wi - Fi and in Windows network connection issues. http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  I suggest you to respond with more information to help you best.

  Suggestions for a question on the help forums

  http://support.Microsoft.com/kb/555375

• RALink RT3290 stops responding after waking up from hibernation, loss of connection

  RALink RT3290 802.11bgn Wi - Fi adapter (driver 5.0.37.0 25.11.2013) stops responding after waking up from hibernation, loss of connection. To recover, it must be restarted (toggle), what happens no wired connection, for example, obviously, drivers Ralink need good alarm clock a reset. Thank you in advance.

  Looks like that driver update solves the http://www.mediatek.com/en/downloads/ problem

• Unable to connect to my office that is connected to the same homegroup.

  Original title:

  access to my files on my desktop that is connected to my homegroup problem

  I am unable to connect to my office that is connected to the same homegroup. When I try to access the shared folder my office requested username and password that I had disabled protected by word sharing wat I do? I had tried my group residential password and my name as user but still cannot connect... Thanks for giving me a solution to this problem.

  Hello

  1 did you changes to the computer before the show?
  2. What are the operating systems connected to the homegroup? Is this the same version of Windows?

  3. what anti-virus software is installed on the computer?

  Check if the homegroup settings is correct:
  Homegroup from start to finish
  http://Windows.Microsoft.com/is-is/Windows7/help/HomeGroup-from-start-to-finish

  Method 1:
  Try the troubleshooter from the following link and check if it makes a difference:
  Open the homegroup troubleshooting utility
  http://Windows.Microsoft.com/en-us/Windows7/open-the-HomeGroup-Troubleshooter

  Method 2:
  You can try the steps from the following link and check if it helps:
  Why I can't join a homegroup?
  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-join-a-HomeGroup

  I hope this helps!

• Loss of connectivity to storage device

  It seems that I get one of them at least once a day.  A few times the data store is unknown and other times told me the name of servers.  I have 4 servers in my cluster, all Dell and an EqualLogic iSCSI SAN.  I'm really at a loss about why it continues to be.

  Loss of connectivity to storage device

  NAA.6090a028d0d00181588b241d3c7352b1. road

  vmhba33:C0:T25:l0 is down. Affected

  data warehouses: unknown.

  error

  2009-09-20 14:47:02

  Hi Chris:

  Make sure that you have configured according to the PDF attached things EQL. There have been some changes of VI3.5 regarding the iSCSI configuration and initiator software was completely re-written in vSphere. For example, multiple paths is a little different, and they recommend you actually have a vmkernel port for each physical NIC and that substitute you the failover parameters. You are or ESX servers can be remove connections that the volume rational access EQL moving to different Eth interfaces on the controller (just a thought). This is explained in the document.

  There is also a video cool tech that goes along with the document. http://www.EqualLogic.com/ResourceCenter/video.aspx?ID=8455

  Let me know if it helps!

  Dave

• Remote Office - error message: version 6 Remote Desktop Connection Client or later is not installed

  Hello

  I am running windows vista home edition at home and I want to connect to my computer at work when I try it I get a message saying that the later version or version 6 Remote Desktop Connection client is not installed, it is not available in vista home? If not what is the best solution for this

  Thank you

  It is based on the operating systems on both ends of the connection.

  Here are some limitations you should consider where they apply: http://windows.microsoft.com/en-US/windows-vista/Connect-to-another-computer-using-Remote-Desktop-Connection.

  Here's how to enable Remote Desktop Connection in Vista: http://www.howtogeek.com/howto/windows-vista/turn-on-remote-desktop-in-windows-vista/.

  Here another article on how to enable the remote desktop connection: http://www.mydigitallife.info/2007/01/26/turn-on-or-enable-remote-desktop-on-windows-vista/comment-page-1/.

  Here's how to work with the desktop client remote: http://www.onecomputerguy.com/networking/vista_remote_desktop_client.htm

  Here's how to add DRC to Home Basic using 3rd party software (if necessary): http://www.pctipsbox.com/add-remote-desktop-access-to-windows-vista-home-editions/.

  I hope this helps.  Keep me posted.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• How to enable remote workers to use connection internet main office

  Hi all

  I just set up our new 1802 as our internet firewall and a VPN server easy and everthing works fine. The only problem is that connected VPN Clients cannot access the internet. It is a policy of companys that all traffic from remote users must be encrypted and send them to the central part, so split tunneling isn't? t an option.

  I added the addresses IP of SDM_Pool of remote to the NAT ACL and reasons workers that the ACL is used by some packages that generates my "IBM Sametime", and this traffic can be seen in the ip nat translation. But the destination in this packet is a local ip (172.16.17.x) network so that in the case of EIB a package that is not coordinated.

  My question is, what happens to packets encrypted once they are decrypted in the esayVPN Server (what are the dest a source ip) and how to configure my router NAT packets to the IFs - external IP, because it isn? t incoming traffic on the inside, that is configured as ip nat inside.

  Thanks for your suggestions.

  Matthias

  This should help...

  http://www.Cisco.com/en/us/products/sw/secursw/ps2308/products_configuration_example09186a008073b06b.shtml

  Please evaluate the useful messages.

• connect a 3rd server in a remote office connection

  Hello

  We have a VDI environment running in America. It has 2 servers connection (independent.  An only external server connections, the other serves as internal connections only.

  One of our European offices needs to have the virtual desktop solution. Due to limitations in bandwidth, performance and al., they need a local solution.

  Is it possible to add a third connection server in this European office? Is it possible to integrate this third server in the connection with our environment VDI existing in the USA?

  We plan to redirect European customers using a pool specialist for European users.

  Thanks for any help you can provide

  EM

  I think that right now everyting must be local to the Europle office.  No integration with the broker of connection from the American point of view.

• had a problem with the remote office, locking of the time-out and the remote host

  I have two computers that both are connected to the network of my company.  Both computers have Windows XP Professional Version 2002 Service Pack 2 installed.  Both computers were set up for remote desktop connection.

  Computer A is a desktop unit and computer B is a portable device.

  Computer A, I can run the remote desktop to computer B without any problem.

  When I run the desktop remotely from computer B to computer A:
  -I see the typical login screen
  -After I typed the user name and password, and then after about 30 seconds, I got the message delay: "the remote connection has expired.  Please connect to the remote computer again. »
  -at this point, the computer A's lock-up, does not have a mouse or a keyboard. the only way out is turning the device off.

  I spent hours on the website of microsoft looking for possible solutions, but can't find.

  According to some suggestions, I have disabled "Symantec Endpoint protection" and "Microsoft Office Communicator", but it did not help.

  Any help is appreciated.

  Check out this thread

  http://en.community.Dell.com/forums/t/19271963.aspx