Default VPN Gateway problem

Similar Questions

• Problem VPN gateway to gateway Cisco RV042 861

  Hello. I have problems with tunneling IPSec between a RV042 and a Cisco 861. I configured the IKE, turn the value, the access list and the Crypto map into the pit 861 the console and I configured the tunnel in the RV042 web application with the same IKE encryption, Diffie-Hellman group and authentication but the connection does not work. Advice or review for this type of connection? Thank you.

  Your default traffic will be natting to the outside world.

  You need without Nat Traffc of Source ip to Destination ip that you authorized in the VPN access list.

  Mean simply to deny source ip to destination ip in NAT ACL.

• Remote VPN gateway to gateway problem RV016 to add VLANs

  Hi all I have a little problem with RV016. I have a site to another LAN ipsec virtual and I would like to add a vlan remote for tunneling but RV has only three options

  -IP

  -Subnet

  IP range-

  Now the remote lan for vpn is 192.168.10.0/24 and I would add 10.1.1.0/24

  Can someone help me?

  Glad to hear it

  Please note the post useful and mark it as answered to help other customers of Cisco

  See you soon

  Mehdi

• VPN Client problem

  A remote user on our network has problems with the Cisco VPN. They are using Win XP, Cisco Client 3.5.2 and connect via a router of Compaq Ipaq into a modem cable. When they VPN in our 3000 VPN concentrator works very well. When they try to VPN in the PIX on our network, it indicates that the client is no longer. If they use a Microsoft VPN to connect to the network with the 3000 (we run both MS and Cisco VPN) with it set to use the remote control, the default gateway, the Cisco VPN will connect to the PIX, see the network behind PIX, ping stuff behind the PIX, but not map a drive. The remote user can ping the PIX of their unVPNed in the remote location. No other user is a problem connecting to the PIX (except those with the bad remote access or broadband satellite which cannot VPN into anything anyway). We have even a few AOLer connect to it. Help me please.

  If the compaq ipaq router makes a PAT, that might be the problem. PIX is unable to manage the ipsec clients who crossed pat. The vpn3000 has some mechanism to deal with this. PPTP is different to ipsec.

  You must ensure that the ipsec client has its own public routable ip address.

  Kind regards

• Internet access from the default remote gateway? NO SPLIT TUNNELING

  I am facing a problem for a long time, I have an ASA5505 I went through a lot of config and research until I got the inside interface to be able to go to the internet; However my VPN clients are unable to go to the Internet. Now, here's the network config:

  -J' have a router (which is a modem and a router and an AP) 3 in 1... This router is connected to the ISP with a coaxial cable. the Interior is 192.168.0.0/24 network.

  -L'ASA is connected to rotate inside the network of its ' outside the interface.

  -L' SAA within the 192.168.1.0/24 network is a configured static gateway already (which is the router) outside the int > default gateway 192.168.0.1 (which is the internal IP address of the router).

  -Inside the ASA computers are able to connect to Web sites (but I can't do anything outside the network of CMD PING)!

  -When a VPN cleint to connect using IPsec (without certificate) by using a Cisco VPN client software, the client can ping and do the remote desktop connection with computers on the same within the network (192.168.1.0/24) but can not pass the Internet even know that other computers on the network can go to the internet.

  -One of the computers on the network (the inside network) is a DC server 2008 R2 which can go to the internet, as I mentioned above.

  What I'm trying to do is have the VPN clients to be able to go to the internet with the help of which the ASA inside the NETWORK card as a default gateway (192.168.1.1), I already have the VPN configuration with the name of the group, preshared key, user name and password and without the split tunneling (which is what I want)

  Thank you

  Hello

  The most common problem by getting ICMP to work through the ASA failed ACL or the ICMP Inspection rules.

  Check your configurations of current ' policy-map ' on the SAA with the command

  See the race policy-map

  I assume you have the default configurations 'policy-map' on the SAA, that are attached to the global

  Under ' policy-map ' configurations, you should see several 'inspect' commands. Pass under the correct configuration mode (where the current commands are found) and add the following

  inspect the icmp

  inspect the icmp error

  Then retest the ICMP through firewall.

  In regards to the VPN Internet traffic, we would need to know the level of Software ASA which you can check with the command 'show version'

  You must first verify that you have this command

  permit same-security-traffic intra-interface

  This will allow the traffic to the VPN users access the interface ' outside ' of the ASA, get PATed and then leave again through the ' outside ' interface. Without the command above it will not work. Will never go the VPN Internet user traffic through the interface "inside" of your ASA.

  Then, you will also need the dynamic configuration PAT for your VPN users, so they are translated at the same IP address that users of LAN behind the ASA. This format of configuration depends on the software level, that I mentioned above

  On a SAA running 8.2 (or below) you would usually have this configuration

  Global 1 interface (outside)

  nat (inside) 1 0.0.0.0 0.0.0.0 (or the mentioned specifically LAN)

  To activate the dynamic PAT for VPN users that you would add

  NAT (outside) 1

  On one ASA 8.3 running (and above) you can configure the dynamic PAT for users of VPN in the following way

  network of the VPN-PAT object

  subnet

  dynamic NAT interface (outdoors, outdoor)

  It should be. Of course, you could have a configuration that may replace it, but I doubt it.

  Hope this helps

  -Jouni

• Windows Update clears my default internet gateway setting

  Win 2008 Server operating system

  I did the windows updates last night when I turned off the computer for the day.
  I was today - unable to connect to the internet. What I found to be the root of the problem, is that there can be no entry for a default gateway address.
  Since then, I found that if I put the IP (v4) DHCP settings - then everything is ok. When you specify a static ip address there are some problems with the address of the bridge not saved, but most of the time, it worked. However, restarts, the default gateway was again absent.

  So basically my current workaround is to switch back and between dhcp and static to get my correct configuration.

  Anyone know why this is happening?

  Thank you

  Thank you for visiting the website of Microsoft Windows Vista Community. The question you have posted is related to Windows Server 2008 and would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://TechNet.Microsoft.com/en-us/bb676078.aspx

  Martin
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Want 4524: hp envy 4524 DNS Gateway problem

  Hello eveyone!  Please help technically challenged, very frustrated new Member!

  I want to HP 4524, but I have enormous problems trying to keep connected to instant ink, and I am now getting the message that my impression is off unless I connect.

  Previously, I managed to find the numbers a forum somewhere that has guided me through the evolution of the default gateway and subnet mask (which they are!), but now there are already there and I can't delete them and it does not connect.  Most of the posts I've seen for similar fixes have numbers such as 8.8.8.8, but mine is as follows:-xxx.xxx.xxx.xxx so I can't enter just one number then point, another number then dot etc. (if necessary?)

  Is anyone able to give me very simple instructions on something that might work please?

  Don't know if this can help, but I use a netgear router and I'm on a mac (OSX update) - what can I please?

  Thank you so much in advance.

  Sort!

  I found another way to get the code to request here

  http://support.HP.com/GB-en/document/c03550536

  and it worked.  Phew!

  Thanks for your help anyway, just sorted now happy.

• Route Internet traffic against the default VPN on SAA route

  I want to transfer all internet traffic to a VPN connection via the internal network and not divided the digging of tunnels or direct connection to the internet from the OUTSIDE interface.

  I have a VPN connection default gateway, so all traffic is pushed back on the OUTSIDE interface when the VPN is in place and the user connects to the Internet.

  Is it possible to send Internet traffic to the INSIDE interface, internal network, to route to the Internet.

  I'm not looking for another solution, it's the design, I would like to implement.

  

  As always, any help is greatly appreciated.

  Of course you can, simply set the following text:

  Route inside 0.0.0.0 0.0.0.0 in tunnel

  The foregoing will force all VPN traffic after be decrypted to the next break of the SAA within the interface defined above

• AnyConnect VPN setup problem

  Hi all, I'm going to have bad configure anyconnect VPN on my router. I'm CCENT pre level and especially followed a tutorial, but feel I'm missing something simple here.

  It's a fairly simple installation on a Cisco No. 2851 - faces of a single interface my LAN 192.168.1.0/24, the other has a public IP address.

  I created a network 192.168.2.0/24 VPN users, mainly to have phones Android connection of their mobile phone networks, and have access to the servers/security cameras/etc by using their local IP addresses. When my phone connects, it gets an IP address and is connected, but is not communicating with my LAN correctly.

  The VPN client can ping 192.168.1.254 (the router's LAN IP) - but not the other devices on the network. However, the devices on my LAN can ping the VPN clients to their address 192.168.2.x.

  Here's a copy of my current config, I have reorganized some elements with #s. Also pasted my ip sh road under him. Do not forget that I am a novice, please forgive the hack :)

  Router (config) #do sh run
  Building configuration...

  Current configuration: 5782 bytes
  !
  ! Last modification of the configuration at 02:24:24 UTC Sat Sep 5 2015 by #.
  !
  version 15.1
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  host name #.
  !
  boot-start-marker
  boot-end-marker
  !
  !
  enable secret $5 1$ 0 #.
  !
  AAA new-model
  !
  !
  AAA authentication login default local
  AAA authentication login local sslvpn
  AAA authorization exec default local
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  !
  !
  dot11 syslog
  no ip source route
  !
  !
  IP cef
  !
  DHCP excluded-address 192.168.1.200 IP 192.168.1.254
  DHCP excluded-address 192.168.1.1 IP 192.168.1.10
  !
  pool of dhcp IP LAN
  network 192.168.1.0 255.255.255.0
  Server DNS 192.168.1.254
  by default-router 192.168.1.254
  !
  !
  IP domain name # '.com'
  host IP Switch 192.168.1.253
  8.8.8.8 IP name-server
  block connection-for 2000 tent 4 within 60
  connection access silencer-class SSH_MGMT
  No ipv6 cef
  !
  Authenticated MultiLink bundle-name Panel
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  voice-card 0
  !
  Crypto pki token removal timeout default 0
  !
  Crypto pki trustpoint TRUSTPOINT-MY
  enrollment selfsigned
  Serial number
  name of the object CN = 117-certificate
  crl revocation checking
  rsakeypair my-rsa-keys
  !
  !
  MY-TRUSTPOINT crypto pki certificate chain
  certificate self-signed 01
  ##########################

  #########################
  quit smoking
  !
  !
  license udi pid CISCO2851 sn FTX1026A54Y
  # 5 secret username $1$ yv # E9.
  # 5 secret username $1$ X0nL ###kO.
  !
  redundancy
  !
  !
  property intellectual ssh version 2
  !
  !
  !
  !
  !
  !
  !
  !
  interface GigabitEthernet0/0
  LAN description
  IP 192.168.1.254 255.255.255.0
  IP nat inside
  No virtual-reassembly in ip
  automatic duplex
  automatic speed
  !
  interface GigabitEthernet0/1
  WAN description
  No dhcp client ip asks tftp-server-address
  No dhcp ip client application-domain name
  DHCP IP address
  IP access-group ACL-WAN_INTERFACE in
  no ip redirection
  no ip proxy-arp
  NAT outside IP
  No virtual-reassembly in ip
  automatic duplex
  automatic speed
  No cdp enable
  !
  interface Serial0/0/0
  no ip address
  Shutdown
  !
  interface virtual-Template1
  !
  local IP 192.168.2.100 WEBVPN-POOL pool 192.168.2.110
  IP forward-Protocol ND
  no ip address of the http server
  no ip http secure server
  !
  !
  The dns server IP
  IP nat inside source list INSIDE_NAT_ADDRESSES interface GigabitEthernet0/1 overload
  !
  IP access-list standard INSIDE_NAT_ADDRESSES
  permit 192.168.1.0 0.0.0.255
  permit 192.168.2.0 0.0.0.255
  IP access-list standard SSH_MGMT
  permit 192.168.1.0 0.0.0.255
  permit 207.210.0.0 0.0.255.255
  !
  IP extended ACL-WAN_INTERFACE access list
  deny udp any any eq snmp
  TCP refuse any any eq field
  TCP refuse any any eq echo
  TCP refuse any any day eq
  TCP refuse any any eq chargen
  TCP refuse any any eq telnet
  TCP refuse any any eq finger
  deny udp any any eq field
  deny ip 127.0.0.0 0.255.255.255 everything
  deny ip 192.168.0.0 0.0.255.255 everything
  permit any any eq 443 tcp
  allow an ip
  !
  exploitation forest esm config
  NLS RESP-timeout 1
  CPD cr id 1
  !
  !
  !
  !
  !
  !
  !
  control plan
  !
  !
  !
  !
  profile MGCP default
  !
  !
  !
  !
  !
  access controller
  Shutdown
  !
  !
  !
  Line con 0
  exec-timeout 0 0
  Synchronous recording
  line to 0
  exec-timeout 0 0
  Synchronous recording
  line vty 0 4
  exec-timeout 0 0
  Synchronous recording
  entry ssh transport
  line vty 5 15
  exec-timeout 0 0
  Synchronous recording
  entry ssh transport
  !
  Scheduler allocate 20000 1000
  !
  Gateway Gateway-WebVPN-Cisco WebVPN
  IP interface GigabitEthernet0/1 port 443
  SSL rc4 - md5 encryption
  SSL trustpoint TRUSTPOINT-MY
  development
  !
  WebVPN install svc flash:/webvpn/anyconnect-linux-3.1.03103-k9.pkg sequence 1
  !
  WebVPN context Cisco WebVPN
  title "Firewall.cx WebVPN - powered by Cisco"
  SSL authentication check all
  !
  list of URLS "rewrite".
  !
  ACL "ssl - acl.
  ip permit 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
  permit ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0
  Licensing ip 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0
  !
  login message "Cisco Secure WebVPN"
  !
  webvpnpolicy political group
  functions required svc
  filter tunnel ssl - acl
  SVC-pool of addresses 'WEBVPN-POOL' netmask 255.255.255.0
  generate a new key SVC new-tunnel method
  SVC split include 192.168.1.0 255.255.255.0
  Group Policy - by default-webvpnpolicy
  AAA authentication list sslvpn
  Gateway Cisco WebVPN bridge
  Max-users 5
  development
  !
  end

  Gateway of last resort is #. ###. ###. # network 0.0.0.0

  S * 0.0.0.0/0 [254/0] via #. ###. ###.1
  (###ISP))) is divided into subnets, subnets 1
  S (# #ISP #) [254/0] via (# publicgateway #) GigabitEthernet0/1
  ###.###.0.0/16 is variably divided into subnets, 2 subnets, 2 masks
  C ###.###.###.0/23 is directly connected, GigabitEthernet0/1
  The ###.###.###.###/32 is directly connected, GigabitEthernet0/1
  192.168.1.0/24 is variably divided into subnets, 2 subnets, 2 masks
  C 192.168.1.0/24 is directly connected, GigabitEthernet0/0
  The 192.168.1.254/32 is directly connected, GigabitEthernet0/0
  192.168.2.0/32 is divided into subnets, subnets 1
  S 192.168.2.100 [0/0] via 0.0.0.0, Virtual Network1

  can you try to disable the FW on your internal lan hosts and then try and ping from users of vpn client

• Application VPN ping problem

  I installed a vpn for access to HVAC equipment suppliers.

  The profile is RCPS_Vendor

  DHCP pool is RCPS_Vendor

  Finished outdoor int

  Here are the steps I took:

  remote access, outside of the--> psk (password), RCPS_Vendors-> authentic local name-> Hoff_Vendor (password)-> RCPS_Vendors 192.168.10.2-192.168.10.128->10.1.252.101/103->3DES SHA 2-> 3DES SHA->10.0.0.0/8 en split tunnel

  from: http://www.cisco.com/en/US/docs/security/asa/asa71/getting_started/asa5500/quick/guide/rem_acc.html

  The question is the seller has ping internal unit, and its program does not connect to units.

  Updated the attached config.

  Thanks in advance.

  All receivers are a section of the ASA, so could you put this static route on each of these units. That would point to the inside interface on the ASA. The ASA would use its default route to send traffic to the VPN clients.

  If the receivers are further inside your network and you are using a dynamic routing protocol, you can redistribute the static route to 192.168.10.0/24 on the next (from ASA) inside your network hop router so that the internal units default gateways to know where to send the traffic destined to 192.168.10.0/24.

  Since your remote clients are sending traffic in VPN tunnels I don't think you need to add an ACL on the ASA to allow specific traffic from VPN clients for the receivers.

• With tunnel VPN ASA5505 problem

  The business needs is for a VLAN again on site to go directly back to an internet service to site B.

  Site A and B are connected by a service of WES MB 100.

  A site is a site of campus with about 25 switches. Him become VLAN on the site is for the engineer access only, so they can access their companys remote access service. This VLAN must stay back so there is very little potential of a trade-off on the live network.

  The solution that I just put in place is to place an ASA5505 as the dhcp server for him VLAN become to Site A. All clients on that VLAN become get a 192.168.100.x address. The external interface on the ASA5505 to Site A is put on the live network to allow a site VPN tunnel to be put in place between the ASA5505 and the Internet - an another ASA5505 firewall

  The Site A ASA5505 was put in place with inside and outside interfaces with the same level of security. 192.168.100.x subnet is exempt from NAT. Traffic is configured to transmit via the interfaces with the same level of security and the tunnel of L2L is coming.

  But I can not all connectivity to the internet from any host on the 192.168.100.x VLAN.

  This is made more complex because the external interfaces on both of the ASA are the corporate network...

  The default route to the Site B ASA5505 is 87.xx.xx.1, the ISP router.

  The Site B ASA5505 connects directly to the ISP router.

  Site has ASA5505

  --------------------

  access-list no. - nat extended ip 192.168.100.0 allow 255.255.255.0 any

  Access access-list ON scope ip 192.168.100.0 allow 255.255.255.0 any

  NAT (inside) - access list 0 no - nat

  Access-Group No. - nat inside interface

  Route outside 0.0.0.0 0.0.0.0 10.0.99.254 1

  Crypto ipsec transform-set AES-256 aes-256-esp esp-sha-hmac

  vpn-traffic 10 crypto card matches the address OUT access

  card crypto vpn-traffic 10 peers set ##Site B IP address #.

  card crypto vpn-traffic 10 game of transformation-AES-256

  vpn-traffic outside crypto map interface

  tunnel-group ##Site B IP address # type ipsec-l2l

  tunnel-group ##Site B IP address # ipsec - attributes

  pre-shared-key *.

  Site B ASA5505

  -------------------

  permit same-security-traffic intra-interface

  access-list no. - nat extended ip 192.168.100.0 allow 255.255.255.240 all

  outside_access_in of access allowed any ip an extended list

  Global (inside) 1 interface

  NAT (inside) - access list 0 no - nat

  NAT (outside) 1 192.168.100.0 255.255.255.0

  Access-Group No. - nat inside interface

  Access-group outside_access_in in interface outside

  Crypto ipsec transform-set AES-256 aes-256-esp esp-sha-hmac

  Crypto ipsec transform-set esp-aes-256 set1, esp-sha-hmac

  card crypto vpn-traffic 10 correspondence address wootton hall

  card crypto vpn-traffic 10 peers set ##Site an IP #.

  crypto-vpn 10 transform-set set1 traffic map

  vpn-traffic outside crypto map interface

  I spent some time on it and really need some advice form experts out there!

  Can you help me to know where I have gone wrong?

  Dan

  There are some parts of the configuration that you have published to that surprise me, such as the assignment of the default route on the inside interface. But these things are not at the heart of your problem. I agree that the core of your problem is probably the sheep access list. If I understand your needs, what you need is 192.168.100.0 is not translated by going to meets B, and is translated by going to the Internet. But your translation says access list never 192.168.100.0 since your access list as another destination:

  access-list no. - nat extended ip 192.168.100.0 allow 255.255.255.0 any

  My suggestion is to rewrite this access list and change the destination of the 'all' to be addresses behind B (LAN to B).

  HTH

  Rick

• Client VPN ASA5505 problem

  My ASA5505Plus to connect to the internet and a laptop, the laptop can access the internet.

  a VPN client connect to the ASA but cannot access internal or external IPs

  I see that the default gateway is wrong, but cannot find how to change it:

  ********************************

  The connection-specific DNS suffix. :

  ... Description: Cisco Systems VPN card

  Physical address.... : 00-05-9A-3C-78-00

  DHCP active...: No.

  ... The IP address: 192.168.200.5

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. : 192.168.200.1.

  DNS servers...: 4.2.2.2.

  ************************************

  I hope that's why I can't access either the laptop (192.168.200.2), Telnet (192.168.200.4) or through the internet via the customer management. I don't know if that part is configured correctly

  configuration see attachment

  Ofir,

  Try the following

  IP local pool VPN_Pool 172.16.20.1 - 172.16.20.254 netmask 255.255.255.0

  inside_nat0_outbound 192.168.200.0 ip access list allow 255.255.255.0 172.16.20.0 255.255.255.0

  no access list inside_nat0_outbound extended permits all ip 192.168.200.4 255.255.255.252

  allow no extended access list inside_nat0_outbound 255.255.255.0 IP 192.168.200.0 192.168.200.0 255.255.255.0

  Split_T 192.168.200.0 ip access list allow 255.255.255.0 172.16.20.0 255.255.255.0

  tunnel-group test general attributes

  address pool VPN_Pool

  no address pool test

  test group policy attributes

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list Split_T

  Crypto isakmp nat-traversal 20

  management-access inside

  Concerning

• ASA 8.3 - SSL VPN - NAT problem

  Need help to find how to configure anyconnect VPN with VPN client using a NAT networking internal.

  There are many items on the side - how to disable NAT for vpn pool.

  I need to create the gateway VPN to the complex international lnetwork, vpnpool is out of range of regular subnet of that network, so it's going to be questions witout NAT routing.

  I so need to vpn clients connected to be PATed to . The problem is that there is also a dynamic to PAT rule for the ordinary acccess Iternet which translates as 'rules NAT asymmetry... "error.

  Create two times different NAT rules and moving them on up/down makes no difference. There are also some hidden rules of vpn setup :-(that could not be seen.

  V8.3 seems is destroying trust in Cisco firewall...

  Thank you.

  Stan,

  Something like this works for me.

  192.168.0.0/24---routeur--172.16.0.0/24 ASA-= cloud = host. (the tunnel he get IP address of 'over' pool, which is also connected to the inside)

  BSNs-ASA5520-10 (config) # clear xlate
  INFO: 762 xlates deleted
  BSNs-ASA5520-10 (config) # sh run nat
  NAT (inside, outside) static all of a destination SHARED SHARED static
  !
  NAT source auto after (indoor, outdoor) dynamic one interface
  BSNs-ASA5520-10 (config) # sh run object network
  network of the LOCAL_NETWORK object
  192.168.0.0 subnet 255.255.255.0
  The SHARED object network
  172.16.0.0 subnet 255.255.255.0
  BSNs-ASA5520-10 (config) # sh run ip local pool
  IP local pool ALL 10.0.0.100 - 10.0.0.200
  local IP ON 172.16.0.100 pool - 172.16.0.155
  BSNs-ASA5520-10 (config) # sh run tunne
  BSNs-ASA5520-10 (config) # sh run tunnel-group
  attributes global-tunnel-group DefaultWEBVPNGroup
  address pool ON

  If I get your drift... bypass inside and outside is not really necessary on Cisco equipment as it should work straight out of the box via the proxy arp, but I'm not face or solution providers for remote access.

  Marcin

• Cisco 2621 to VPN client problem

  If I ping on the client to the network (behind the router), debug displays the client encryption and decryption of the router. The ping will not, because the router is not encrypt and so the customer is not getting anything to decrypt.

  The Setup is a bit different because the default route is within the network, as it is not the regular internet gateway. I have to add routes for pointing the customer who logs on the internet. Also, one machine uses this as a gateway (using a routemap). To troubleshoot, I removed the routemap custom without result. I think to change the default route, but I don't see how this would have on it.

  Any ideas? Am I missing something?

  Cisco 2621 12.2 (15) T running to the latest version of the client.

  username password XXX 7 XXXXXX

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  AAA - the id of the joint session

  IP subnet zero

  !

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group customer crypto isakmp XXXX

  key XXXXX

  pool ippool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  !

  interface Loopback1

  192.168.254.1 IP address 255.255.255.0

  !

  interface FastEthernet0/0

  IP address 200.x.x.x 255.255.x.x

  no ip proxy-arp

  NAT outside IP

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface FastEthernet0/1

  the IP 10.0.0.1 255.255.255.0

  no ip proxy-arp

  IP nat inside

  route CUSTOMGATE card intellectual property policy

  automatic duplex

  automatic speed

  !

  IP local pool ippool 10.172.10.100 10.172.10.200

  IP nat inside source map route sheep interface FastEthernet0/0 overload

  no ip address of the http server

  no ip http secure server

  IP classless

  IP route 0.0.0.0 0.0.0.0 10.0.0.30

  access-list 100 deny ip 10.0.0.0 0.0.0.255 10.172.10.0 0.0.0.255

  access-list 100 permit ip 10.0.0.0 0.0.0.255 any

  username password XXX 7 XXXXXX

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  AAA - the id of the joint session

  IP subnet zero

  !

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group customer crypto isakmp XXXX

  key XXXXX

  pool ippool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  !

  interface Loopback1

  192.168.254.1 IP address 255.255.255.0

  !

  interface FastEthernet0/0

  IP address 200.x.x.x 255.255.x.x

  no ip proxy-arp

  NAT outside IP

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface FastEthernet0/1

  the IP 10.0.0.1 255.255.255.0

  no ip proxy-arp

  IP nat inside

  route CUSTOMGATE card intellectual property policy

  automatic duplex

  automatic speed

  !

  IP local pool ippool 10.172.10.100 10.172.10.200

  IP nat inside source map route sheep interface FastEthernet0/0 overload

  no ip address of the http server

  no ip http secure server

  IP classless

  IP route 0.0.0.0 0.0.0.0 10.0.0.30

  IP route 20.x.x.x 255.255.255.255 200.x.x.x (it is here to let him speak to the customer)

  access-list 100 deny ip 10.0.0.0 0.0.0.255 10.172.10.0 0.0.0.255

  access-list 100 permit ip 10.0.0.0 0.0.0.255 any

  access-list 110 deny host ip 10.0.0.73 10.1.0.0 0.0.0255

  access-list 110 permit ip 10.0.0.73 host everything

  !

  CUSTOMGATE allowed 10 route map

  corresponds to the IP 110

  IP 200.x.x.x next value break

  !

  sheep allowed 10 route map

  corresponds to the IP 100

  !

  !

  CUSTOMGATE allowed 10 route map

  corresponds to the IP 110

  IP 200.x.x.x next value break

  !

  sheep allowed 10 route map

  corresponds to the IP 100

  !

  Add at least:

  > Route ip 10.172.10.0 255.255.255.0 200.x.x.x

  to force the traffic for VPN clients on the external interface. also make sure you hav a route for the clients IP address (not the VPN negotiated one) that also indicates the external interface.

  The fact that the router is not encrypt means that it is not even see the responses from the inside, hosts, which indicates that your internal network is not a road to 10.172.10.0 pointing to this router, OR the router receives responses but sends them back out inside interface which will be set by the first route, I mentioned above.

• ASA 5510 IPSEC VPN connection problem

  Hello

  We have an ASA 5510 (ASA version 8.0) of remote access VPN configured and works most of the time, but there is a problem when you have more than one client that connects to the same office remotely.  When the first VPN client is connected to the remote desktop, everything works fine, but when the second client connects to the VPN, it connects fine but do not get any traffice return to customer.  I can see under monitor-> statistical VPN-> Sessions-> remote access-> Rx Bytes is 0. Both connections are from the same public IP address of the remote desktop.  I changed some settings on NAT - T and a few other things, but without success.

  Could someone help me please how to fix this?

  Thank you very much.

  Make sure that customers use because that probably her you're not. (default value is NAT - T).

  Federico.