Removal of Directors in vCenter 4?

Similar Questions

• Move the VM from: vCloud director to vCenter

  How to move a virtual machine from: vcloud director to the vcenter even integrated into vcloud Director?

  If VCD has no more need of this virtual machine, you can perform steps below.

  1 unregister the virtual of VC machine

  2 remove the machine virtual de VCD

  3. save the VM in VC

  SCR would be an additional tool that would be useful for moving loads of work, but a lot depends on number of cases of use of involved and of the virtual computer.

• to remove the Director

  Well, when I try to go anywhere my computer goes to movie maker. I want to remove it.

  JO Ann Dove

  Hi Jodove,

  A default program is the program used by Windows when you open a particular type of file, such as a music file, an image, or a Web page.

  It could be that by default has been changed to movie maker, so whenever you try to open any music file, an image or a webpage opens Director.

  Are you referring to Windows Live Movie Maker?

  You can view the steps in this article and check if that helps.

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  Also, take a look on the following article for more information:

  Change the programs that Windows uses by default

  If you are referring to Windows Live Movie Maker and you want to uninstall, and then refer to:

  How to uninstall one or more programs Windows Essentials?

  Please post with the State of the question.

• Remove a cluster in vCenter 5.5

  I have two hosts in a cluster. I want them both to a new server vCenter (2012 R2).

  I spend in maintenance mode to move the host because they are in a cluster. However, I can choose culter and then remove and I get a warning "removing a cluster remove also all the hosts and virtual machines. Are you sure you wan to do this? »

  Remove a cluster will both hosts in maintenance mode or it will remove the cluster and put both hosts up one level (data center) without going into maintenance mode?

  Thank you

  Tjcooper

  There is no need to use the Maintenance Mode. What I've done for the past migration was to disable HA and DRS manual value (maybe not necessary though), then 'Disconnect' hosts to vCenter and finally 'remove' them before adding them to the new environment. You must still work to 'force' add hosts to the new vCenter Server without removing them from the old. Once guests are added to the new vCenter Server you can move them to a cluster (CPU/VCA compatibility provided).

  André

• How to remove Cluster hosts in vCenter

  We have a VMware vCenter 5.5 license that is about to expire, and while we re-new the vCenter license, I have to take all the VMS that are associated with a group called:

  Orlando (site) > staging (cluster) > 10.1.1.13 (home) > testbox1 (vm)

  I need to remove the (host) (cluster) above. I can do this by typing "Mode of Maintenance", which then moves the (vm) to another host in the staging (cluster). Problem is when I go out "Maintenance Mode", (pole) is placed in staging and the virtual computer is moved to the staging (cluster) > 10.1.1.13 (host). This is NOT what I want. I want to delete all hosts in staging (clutser) independently in vCenter before my vCenter license expires.

  Can anyone please explain or help me do this?

  Thanks in advance.

  Hi Carlos,

  Hope that you use the web client.

  Basically, the question is, you must remove a host in a cluster have DRS and HA.  To remove a HOST

  Put the HOST in maintenance mode - > check all VM's was able to move to another HOST, then right-click and disconnect, finally right click and delete.

  If you need to keep the virtual machine to the same physical host and you have properly configured a standard switch.

  Click with the right button on the cluster and DRS recommendation opt for manual. maintenance mode, then right click and then disconnect, finally just right-click and delete.

  hope this helps you.

• Remove ESXi hosts to vCenter Cluster host even

  Hi all. Depending on the subject, I would like to remove the host from an old Cluster vCenter which is no longer accessible because the database is damaged. Unfortunately I can not not to restore it because my predecessor scheduled backups. How can I do? Thank you all in advance for your answer.

  All the information you have provided, I suppose there could be something in the ADAM database, which must be deleted / reset.

  The assignment of license keys is stored in the ADAM database (rather than in the vCenter Server database) and with the new installation of server vCenter on the same host (old) this may not have been reset. Please take a look at http://kb.vmware.com/kb/1015268 to see if this KB will help resolve the issue.

  André

• Map ID between vCloud Director and vCenter Chargeback by API

  I currently have a configuration where vCenter Chargeback automatically imports the hierarchies of vCloud Director by a data collector. I find difficulty in mapping a vCloud Director ID entity in a vCenter Chargeback one.

  I'll give a practical example:

  I vCloud Director organization ORGNAME and VM VMNAME.

  I want to generate a chargeback for the entity VMNAME report. How do I tell me what ID of entity should I spend in the report query if the only information I have comes from the vCloud Director?

  Thank you in advance,

  Marco

  Hi Marco,.

  To get the Id of the virtual machine in the entity report request, you have the following option: -.

  • Go step by step to VM, in this approach, you have to call according to API

  1. Get all the hierarchies, GET hierarchies--> this response API, get the id of the hierarchy based on the hierarchy name (name of the hierarchy will be same as the name of the Organization to vCloud Director)
  2. Hierarchy of browse, GET /hierarchy/ {hierarchyId} / browse--> this the API response, you get the id of the entity of the root of the hierarchy
  3. Entity to browse, GET /entity/ /hierarchy/ {hierarchyId} {entityId} / browse--> this response from the API, you will GET the ID of the entity for immediate children of the entity of the root of the hierarchy
  4. Go by calling the entity API browse recursively until you reach your desired VM (or entity).

  Please note that travel entity API returns very few details about the entity (name and entity id). If you want to filter your VM (or other entity) based on the name, this might be enough for you.

  But if you want to filter your VM (or other entity) on other criteria, you may need to call ' entity Get GET /entity/ /hierarchy/ {hierarchyId} {entityId} "API for more details on the entity.

  If you to filter the VM (or other entity) based on the attribute custom, you can use the API ' get the attributes of an entity, GET /hierarchy/ {hierarchyId} /entity/ {entityId} / attribute.

  • If the size of your hierarchy is not great (you don't have too many entities in the hierarchy), you can follow the following approach: -.

  1. Get all the hierarchies, GET hierarchies--> this response API, get the id of the hierarchy based on the hierarchy name (name of the hierarchy will be same as the name of the Organization to vCloud Director)
  2. Get hierarchy, GET /hierarchy/ {hierarchyId}--> this response API returns you all entities in the hierarchy with a single blow. Once again very little detail of the entity is returned (name and entity id), if you want to refine your entity on other criteria rather than by name, then you need to use 'Get entity' or 'Get the attributes of the entity year' as explained above.

  Please note that if Director vCloud in vCenter Chargeback hierarchies that are filled automatically, there is a named "vCloudEntityId" located on the rebilling of entities corresponding to entities vCloud Director of custom attributes. The value of the custom attribute "vCloudEntityId" represents the entity type id and the vCloud vCloud Director entity.

  For example, if a TIME named "helloVapp" has id 123456 into vCloud Director. Then in vCenter chargeback the value of the custom attribute "vCloudEntityId" will be "VcloudVappEntity-123456"for this "helloVapp" TIME."

  I hope this helps.

  -Amrainder

• Cannot remove vCenter vDS 5.5

  Hi all

  I am trying to remove a switch distributed the vcenter but it comes up with an error message box:

  «vDS SW-DCN-C1_C2 port c-40 is used by the entity < not found.» "> Virtual NIC 4000, type: vmVnic.

  I remove all the groups from ports and I remove all the hosts and vm that were connected to vds.

  I move down, all the vds and c-40 port id to "Unused uplinks" dvUplink in consolidation and failover policies.

  What otherwise I can do?

  Thanks for the help everybody.

  You can remove the entry from vCenter Database its under vpx_entity

  Run the script in management studio below if you are using the MSQL.

  Select * from VPX_ENTITY by name;

  Search for the name of the object that is DVswitch and get the ID of the object and remove it by running the script.

  get involved DB admin to run the script.

  take a snapshot of the vCenter if VM is a virtual machine and a backup of the DB

  If the object is not found even in DB, try to remove it from vCenter MOB.

  https://VC.FQDN.com/mob

  This will help for sure.

  I had the same problem once.

  in my case the DvSwitch has been removed, but the uplink remained in vCenter view

  When I tried removing it (object cannot be found)

• Remove host to vCenter, but keep the functional VMs on host?

  I managed on the basis of 3 guests by vCenter Essentials over which limit myself to 3 hosts managed by vCenter.  3 all hosts are connected to storage arrays, SAN, through Dell Power Connect switches.

  I want to delete a host to add a beefier host in his place.  If I remove a host, it will break the connections to the San?... because I want to leave the host VMs powerd on & keep functional.  Is this possible?  Would this work?

  Remove a host to vCenter will not affect SAN connections or virtual machines running - depending on whether you have any DRS you might be forced to put the host in maintenance mode and move virtual machines to other nodes or if you have active HA you can find in a State where you receive warnings about insufficient resources for failover.

  What verion of vSphere use you to place this thread in the approriate forum =

• How do you remove all THE Java code of Vista before a Java reinstall.

  I have (Microsoft Security Essentials) has recently detected viruses in my tree of Java.  While I think that the problem was managed by MSE, I still want to remove completely all my machine Java code prior to a relocation of a pure set of Java.  It seems that Java would not provide you with a removal of Java (like MaAfee) do this, and the only code available tool is the standard Microsoft required uninstall code.  I want to remove all traces of Java code, and I don't usually use (do not trust) of 3rd party code that you find on the Internet, but if anyone has good experience with one of them, I would like to know.

  Even if the uninstaller code seemed to work, I found a lot of leftover Java files and folders left behind.  For example, there is a Sun\Java\... tree located in the AppData\LocalLow directory.  I would like to know why this code was left and whether it is safe to just delete.  I don't like just big clear code because there may be a registry entry based on the code, which could cause another problem to me (even if the Java code is supposed to be uninstalled).

  In the meantime, as an alternative, I renamed all Java directories that I can find.  Roughly the same and about as good what remove Java directories, isn't.

  And finally, I have a Vista 64-bit system, so which implementation of Java should I download/use. When I uninstalled the Java code, there is an updated version of 32-bit (Version 6, 26 update in the list of programs), as well as an outdated version of 64-bit (Version 6, Update 13 instead of Version 6, update 26) in the list programs.  These work together.   I shouldn't have to download both, I have to, or I should.

  And one last comment.  I've been running for a few days now without any Java installed on my machine and do not encounter problems or errors due to the absence of the code.  I know that many of the Applications that I use, use javascript, which I think is a little different that the standard Java code.  So what's the problem here.  Have I just not met a Java-application or is there more parts left Java in the machine I don't know or Windows excuting part of the said code.  I need to Java, I don't.

  roninrr

  Yes, Java is bad enough to remove all its files when uninstall you it but things left to do no harm. You can remove them if you want.

  There is no relationship between Java and Javascript, with the exception of confusion as well as the fact that both languages look a bit.

  You can probably do without Java. Java has become one of the biggest goals for malware recently. I uninstalled Java of my computers a while back I found I was taking more time now know to use it. I was only access a Web site regularly used and find a substitute for it. I could leave uninstalled, and see if you hit what he really needs.

  If you decide to reinstall, the 32-bit version is all you need unless you use Internet Explorer 64-bit (which you shouldn't).

• How can I remove the company administrator and remove all network settings?

  my company put up my system on its network and has administrator rights.  society is more activity, so no to remove the directors of the company.  I'm not able to make changes to my computer.  How can I remome company all the admins/network so I can use my system as admin?

  Hello

  are you being asked to work and make changes in this machine, the admin password and you don't know?

  If so, reinstall vista

  I'm sorry, but the strategy of microsoft in these forums, it's that no assistance will be given about the unknown passwords

  read the policy at the link below

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/keeping-passwords-secure-Microsoft-policy-on/a5839e41-b80e-48c9-9d46-414bc8a8d9d4

• Change the VoP url in vCenter plugin

  We notice that the VoP vCenter plugin accesses our server of VoP by IP address, which generates warnings of certificate. How/where can we change the current https:// the plugin url seems to use something like https:// ?

  Hello

  When this happens, the easiest way to fix is to remove the plugin from vCenter manually, by following this process:

  First, clear the checkbox for the Plugin from vCenter in VoP under settings-> General-> tab environment for the server vCenter in question.

  Then follow these steps to remove the plug-in to vCenter:

  1. In a web browser, navigate to http://Server vcenter or IP name/mob.
     Where the server vcenter or IP name is the name of your server vCenter or its IP address
  2. Click on content.
  3. Click ExtensionManager.
  4. Select and copy the name of the plug-in to remove from the list of values under properties.
  5. Click UnregisterExtension. A new window appears.
  6. Paste the name of the plug-in, and then click the Invoke method. This command deletes the plug-in.
  7. Close the window.
  8. Refresh the window of Managed Object Type: ManagedObjectReference:ExtensionManager to check if the plugin is removed successfully.

  Note: If the plugin continues to appear, you may need to restart the vSphere Client.

  Finally, re-check the plugin at the entrance of the vCenter server in VoP to have re - install the plugin making reference to the new IP address.

  In the future, before changing the IP address of VoP, remove the checkbox on the entrance of the vCenter server and save.  Which will automatically remove the plugin entry, then you can re - check this last after the VoP IP is updated.

• Mobile 5.1 ESXi host in vCenter unpublished 6 - license?

  Hi all -

  If I take an ESXi host 5.1, previously managed (under license) via a given vCenter (also v5.1) and its key in the inventory management, then I disconnect/remove this host from the vCenter 5.1 and connect it to a completely new vCenter, what happens to the host of license?

  It disappear and become a 60-day eval, or his license key moves WITH the host in the new vCenter?  (The new vCenter in this scenario would have absolutely zero license keys from host ESXi that apply to guests of ESXi 5.1 existing installs below)

  I was wondering what 'happens' in this scenario I have the document our so-called steps for migration.  Yes, I know that this could / should all be tested "in the lab" but don't get started me on that.  Thanks for any comments on what I can expect.

  My best guess is that the host will LOSE its license now, it becomes a 'standalone' ESXi host when disconnected and removed from the old vCenter (via the "Delete" command).  I want to just make sure that it is also fully functional, if she has run VMs on it at the time or not (although Yes, I'll put it in maintenance mode before removing the old VirtualCenter and join a new).

  And Yes, of course I have old games of the existing environment 5.1 ESXi license keys.  I'm just trying to set expectations as to what is happening in licenses-wise once I move the host from the old to the new vCenter.  I have all pretty well understood technical pieces, including AVS and DVS network considerations.  Thank you.

  See this thread to another: Re: moving hosts to new vCenter and retaining current licences of host

• Cannot delete host to vCenter

  Hi all

  I have a curious problem here, I am trying to remove a host to vCenter but get the following message: "the object has already been disposed or was not completely created."

  I think there is a certain entity in the vCenter database table over? Anyone any ideas?

  Thank you

  Jim

  Hi André,.

  Thanks for the answer, it turns out that it was a problem with the obsolete entries in the adam database. 5.5 vCenter, had not consulted the web client in a while & only he saw there.

  Kind regards

  Jim

• VCenter broken... I can not reinstall it

  Hello, today attempted to update my server vcenter for windows latest update 6 1 version, unfortunately the update did not work and my installation vcenter was brokened.
  I tried completely uninstalling vcenter without success, so I do a backup database and manually removed all files of vcenter and cleaned the registry...

  Now, whenever I'm doing a new installation, the installer of vmware update do rather a fresh install... How is that possible? How Setup my server to get a copy of vcenter already installed if I removed completely all files and registry references?
  Thank you

  not a VM... in any case I solved, I removed completely all the keys in the windows registry using the software RegScanner self all reinstalled and restored my backup of SQL database

  Thank you