Remove asa5520 access list

Similar Questions

• No not removed from the external interface access-list access list?

  PIX515

  customer wanted to modify the access list (add a new line)

  so he has first publish no access-list command can

  apply the change to the access list, but the access list has been

  removed from the interface outside

  is this a normal behavior? on routers access list stay connected

  for the event of the interface if you issue no access-list command

  Thanks in advance for any comments

  JYP

  Hi Thibault-

  No, it is not a normal behavior, sounds more like an error by the customer. It's always a good idea to copy the required ACL on a text editor (Notepad) do not forget to include "access-group command" i.e. "access-group interface inside inside' or 'access-group out in interface outside' - when copying the required ACL and then issues a 'no access-list inside' or 'no access-list outside' the first line in the ACL copied on your notebook before copy you it to the PIX , also make sure that you are using the config and make an "m wr" (write memory) after the ACL modified have been applied on the PIX.

  Hope this helps-

• Ipv6 access list does not apply autonomous Aironet 3602I-E

  As you can see in the attached config I configured two SSID (2G & 5 G) for a third (2G only) SSID and PEAP WPA2-Ent on the vlan 2 for 'poor team access as guest '.

  Basically I forced the Dot11Radio0.2 interface in the Group of deck 1 to get all three SSIDS on vlan 1 (since I want just a quick way and dirty to allow its customers access to the internet, without having to configure a vlan separate everywhere).

  The guest SSID (XX COMMENTS) allows tkip in addition to BSE and uses a PSK rather than PEAP. Access lists configured on Dot11Radio0.2 IPv4 allows clients connected to this SSID get an IP by DHCP, use the DNS servers on the local network and access the internet. All other traffic for the local network is blocked by access lists guest_ingress and guest_egress.

  This all works very well, ipv4 is blocked for guests invited as expected. However, ipv6 is something different. For some reason, the ipv6 access list is completely ignored.

  Because I don't need ipv6 for guest access, I thought that I have completely block and do with it. As you can see I have this set:

  interface Dot11Radio0.2
  guest_ingress6 filter IPv6 traffic in
  guest_egress6 filter IPv6 traffic on

  and these ipv6 access lists have a rule of "refuse a whole" only. Yet, the XX COMMENTS SSID connected client gets an ipv6 address of the server on the LAN DHCP6 and has full connectivity. For ipv4, that I had to explicitly allow DHCP packets to the client not even get an IP, so the ipv6 access lists are not clearly applied.

  No matter if I move the access interface Dot11Radio0 instead lists, they don't do anything. I thought that maybe I should add a "enable ipv6" on the Dot11Radio0.2 interface (even if ipv6 traffic was very good, even where it shouldn't), but when I set "enable ipv6" Dot11Radio0 or Dot11Radio0.2 the radio goes into a sort of infinite loop of reset:

  000261: Sep 23 2016 22:32:50.512 it IS: % DOT11-5-EXPECTED_RADIO_RESET: restart Radio Dot11Radio0 interface due to the reset of the interface
  000262: Sep 23 2016 22:32:50.516 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
  000263: Sep 23 2016 22:32:50.524 it IS: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
  000264: Sep 23 2016 22:32:51.516 it IS: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
  000265: Sep 23 2016 22:32:51.560 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
  000266: Sep 23 2016 22:32:51.568 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
  000267: Sep 23 2016 22:32:51.576 it IS: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
  000268: Sep 23 2016 22:32:52.608 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
  000269: Sep 23 2016 22:32:53.608 it IS: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
  000270: 22:32:53.608 Sep 23, 2016 it IS: % DOT11-5-EXPECTED_RADIO_RESET: restart Radio Dot11Radio0 interface due to the reset of the interface
  000271: Sep 23 2016 22:32:53.612 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
  etc.

  In addition, when creating a list like this ipv6 access:

  guest_egress6 IPv6 access list
  refuse an entire ipv6

  The other is automatically created:

  IPv6-guest_egress6 role-based access list
  refuse an entire ipv6

  A deletion also removes the other.

  What is happening with these ipv6 ACLs, why they are not blocking all traffic? Why do I get an acl "role-based" too? Is associated it with?

  Is there a another way to kill just any ipv6 on the SSID of COMMENTS XX traffic while leaving alone on others? That's all I need at this stage. If the ipv6 ACL do not work, perhaps this can be done (ab) using a service-policy or policy routing? I'm ready to creative solutions :)

  PS. I know this is not the recommended method to configure a guest SSID, but it should still work IMO.

  You have encountered a bug I discovered a few months ago (CSCva17063), in your case, the workaround is to apply the ACL on the physical rather than the void interface interface (because you want to completely block IPv6 in any case). I write (more) my conclusions regarding the traffic that refusal on autonomous APs in a blogpost, might be interesting for you to read as well.

  Remember that the access point used as a bridge between the wired infrastructure and wireless, not as a router. There's some IOS routing of commands (like the "enable IPv6" command you pointed out) , but these are not the characteristics that should be used or need to be enabled on an access point.

  Because the networks internal and customer spend somewhere else, I would perform filtering on this device instead. Also sub gi0.2 interface is missing from your configuration, so I do not think that access as a guest is currently working at all?

  Please rate helpful messages... :-)

• Cisco 837 and access list

  Hi all

  Sorry if my question sounds stupid, but I had a lot of problems with the syntax of the access list, especially to remove a line in an access list, for example:

  Here is my list of access

  access-list 120 allow ip 192.168.6.0 0.0.0.255 172.16.0.0 0.0.255.255

  access-list 120 allow ip 192.168.6.0 0.0.0.255 172.20.0.0 0.0.255.255

  access-list 120 allow ip 192.168.6.0 0.0.0.255 172.17.0.0 0.0.255.255

  If I want to delete only this line

  access-list 120 allow ip 192.168.6.0 0.0.0.255 172.16.0.0 0.0.255.255

  I do not know how, I if do:

  no access-list 120 allow ip 192.168.6.0 0.0.0.255 172.16.0.0 0.0.255.255

  all the access-list 120 is removed!

  Help, please!

  Olivier

  Hi, this is the usual behavior, if you delete the access list of the entire statement with sequence number is deleted.

  You can create a named extended access-list and have the sequence number for each statements.

  !

  Standard IP access list note

  permit 172.10.0.0 0.0.255.255

  10.1.1.0 permit 0.0.0.255

  permit 192.168.1.0 0.0.0.255

  deny all

  !

  and if you want to delete something in between, or any particular line, you can run the command like this that will remove this line instead of the entire ACL itself...

  Standard note of access-list (config) #ip

  (config-std-nacl) #no 3

  This configuration lines will remove the third line only (which is to allow the 192.168.1.0 0.0.0.255, leaving the other statements)

  regds

• Pix access lists

  I am facing convert statements leads on our PIX 520 access lists. Is there a better way to do this will be as little as possible traffic interruption? For example, to create access lists and then remove the conduit, or vice versa?

  Second, is there a priority recommended in order to access list?

  Hello

  This is a very good paper on the conversion of lines to the ACL, also when writing ACL always have your most important ACL on top of the ACL work from the top down. When you make changes to the ACL or static lines always issue the command clear xlate and save with RAM command.

  http://www.giac.org/practical/GSEC/Bill_Donaldson_GSEC.pdf - by Bill Donaldson, GSEC.

  If you want more information/inf, then let me know.

  Thank you / Jay.

• Hitcnt of compensation on an access list

  I've searched and can't seem to find a way to clean the hitcnt on an access list other than the deletion and restoration of the access list. Does anyone know how to do this?

  Thank you

  J

  Allow Access-list ip x.x.x.x 255.255.255.240 sheep a (hitcnt = 72408)

  6.1 (4) code and most importantly you can use:

  > sheep counters clear access-list

  In the pre - 6.1 code (4) you must remove and re-add the ACL in.

• access list of split tunneling

  Hello

  I have some problems on ASA 5520 split tunneling configuration.

  Here's the scenario:

  Number of remote users connects ipsec with ASA 5520 (in central) using ubuntu vpnc-client.

  Split tunneling is used, in order to allow remote users to surf the Internet using their ISP.

  The goal is to remove the possibility for ssh/telnet servers within the local enterprise network for remote users.

  Here is a part of the config:

  internal REMOTE_gp group strategy
  attributes of Group Policy REMOTE_gp
  VPN-idle-timeout no
  Protocol-tunnel-VPN IPSec
  Group-lock no
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list REMOTE_split

  tunnel-group type REMOTE access remotely

  tunnel-group REMOTE General attributes

  authentication-server-group RADIUSGR

  Group Policy - by default-REMOTE_gp

  REMOTE tunnel-group ipsec-attributes

  pre-shared-key *.

  ISAKMP keepalive retry threshold 15 10

  RADIUS protocol AAA-server RADIUSGR

  AAA-server RADIUSGR (INSIDE_LAN) 192.168.0.244

  REMOTE_split list extended access deny tcp 192.168.0.0 255.255.255.0 ssh telnet rank everything

  permit access ip 192.168.0.0 scope list REMOTE_split 255.255.255.0 192.168.100.0 255.255.255.0

  ip subnet ##192.168.100.0/24 - where from Radius Server to allocate ip addresses to remote users.

  INSIDE_LAN_in list extended access deny tcp 192.168.0.0 255.255.255.0 eq ssh 192.168.100.0 255.255.255.0

  INSIDE_LAN_in list extended access deny tcp 192.168.0.0 255.255.255.0 eq telnet 192.168.100.0 255.255.255.0

  permit access ip 192.168.0.0 scope list INSIDE_LAN_in 255.255.255.0 any

  It has nat enabled on the interface, but there is a special instruction in nat0 ACL for 192.168.100.0 subnet

  permit access ip 192.168.0.0 scope list INSIDE_LAN_nat0_outbound 255.255.255.0 192.168.100.0 255.255.255.0

  The problem is that the remote users can easily ssh and telnet servers in network INSIDE_LAN. Everything I put in INSIDE_LAN_in ACL, remote users still have full access to this network. Restrictions in the REMOTE_split ACL do not work either.

  You must configure vpn-filter rather to block telnet and ssh access as follows:

  Remote filter access list deny tcp 192.168.100.0 255.255.255.0 192.168.0.0 255.255.255.0 eq 22

  Remote filter access list deny tcp 192.168.100.0 255.255.255.0 192.168.0.0 255.255.255.0 eq 23

  distance-filter 192.168.100.0 ip access list allow 255.255.255.0 192.168.0.0 255.255.255.0

  attributes of Group Policy REMOTE_gp

  VPN-value filter-remote control

  Split tunnel acl has the following statement and it should be extended to standard ACLs instead of:

  REMOTE_split list of permitted access 192.168.0.0 255.255.255.0

  Hope that helps.

• How can I remove all numbers listed on my iMac FaceTime audio?

  I have along list of phone numbers on the audio portion of my set-up of FaceTime iMac.  These figures come from phone calls using my iPhone.  I can remove the entire list on my iPhone using the application of the edict, but am unable to find such an application on iMac FaceTime mounting.

  Thank you.

  Right click or Ctrl-click on the address window and choose Remove all recent.

• I can't uninstall Thunderbird to my Windows programs "Uninstall list"; Why does not uninstall and be removed from this list?

  Very frustrating... under windows ' programs/uninstall a program "list, Mozilla Thunderbird is still listed AFTER that I have removed completely (I thought) from my computer. I clicked on 'uninstall' several times and nothing happens. I can't take the fact that Mozilla has set it up so that it can apparently be deleted from this list... What is everything? I tried to research the problem, even by using your Web site without success. All what I want to do is get out of my list to uninstall/change. I used this program AND will not use it. I don't want this program on my computer/list period. I would appreciate your help.

  It is a problem with the management of Windows applications. Mozilla does nothing to interfere with the installation/uninstallation process.

  You could re - install Thunderbird so re-synchronization of the list of applications, then uninstall again, or you could use a utility to remove from the list.

  A search of thunderbird.exe will confirm whether or not it was really deleted, but you may need to disable all the fool-proofing that implement Microsoft for not to see the true state of the file system; Configure to display hidden files and the extensions of file to start.

  Thunderbird is almost independent. You are free to delete manually the folder that the application resides in if Windows fails to uninstall it for you, but that will not solve the incorrect appearance of thunderbird in the list of installed applications.

• How can I remove the long list of notifications I on iPad?

  How can I remove the long list of notifications that I have on my iPad?

  Please treatment this issue Apple.

• Remove the access door and a hard drive HP Pavilion model 17-e119wm (product # F9A46UA #ABA)

  Have a computer Pavilion laptop model HP Pavilion 17-e119wm (product # F9A46UA #ABA). Need the instructions step by step to remove the access door and the hard drive then.

  I need to remove the HARD drive so I can retrieve the data before you install a new HARD drive and reinstall the operating system.

  I don't even find how to remove the access door and do not want to break.

  Any help would be greatly appreciated.

  Thank you

  Interview Guide & is on your Support page.

  http://h10025.www1.HP.com/ewfrf/wc/manualCategory?cc=us&DLC=en&LC=en&product=6761918&

• Removable storage access is denied

  Hello world

  Before my question, I'm not 100% sure that it is related to Windows 7 or Windows Server. Please let me know if I'm wrong.

  A few weeks ago I had to block access to all classes of removable storage to a group of 5 users or more in the company. So I used the "Computer Configuration" GPO (Computer Configuration > administrative templates > system > removable storage access > classes all removable storage: deny access for all 'Active'.) I applied it to the users, and it worked fine. From there, they were able to use the key USB, CD, etc... After awhile, it was decided by the administration they could get access to rear. So I removed the GPO of these users. After some time, users are complaining that access was denied again. From there on, here's my resolve the path

  • I did a GPRESULT and I could see that the GPO has been applied.
  • I looked to the top of local computer policy (gpedit.msc) and this setting is not configured
  • I looked upward in the event viewer in the computers and the domain controller, nothing interesting found
  • I tried to make a GPUPDATE/force and restart
  • I tried to remove the computer from the Active Directory and join it back to the field
  • The GPO still exists, but not applied to users having the problem, I tried with 2 computers of third parties to reproduce the problem. I applied the GPO, denied access to all removable storage classes. I délettrée the GPO and access to all removable storage classes to restore.

  At this point, I don't know what to do. It has been a little hours (days) now that I searched on the internet about this problem and the only user I found that solved this problem, solved by formatting computers upward... This isn't the solution, I want to use.

  Please note that these users are in a connected remote site MPLS to the main site and there is a DC in each site and also the replication works very well.

  Best regards

  Mike

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• Remove "Print Directory Listing" option to context menu in Windows Explorer

  remove the "Print Directory Listing" of Windows 7, the Windows Explorer context menu and corresponding registry cleaning

  This answer is not answering the question of how do to REMOVE the feature list of directories printed after installation using the referenced article.  The question is how you UNINSTALL both printed directories list the choices no longer appears in the right click menu?

  Thank you!

• Windows Explorer "option remove from this list" DOES NOT always WORK

  In Windows 7:
  When you right-click the Windows Explorer button at the bottom of the screen on the task bar, it has an option to "remove from this list. all Frequent ' point/place' that there are listed...

  I used this option during most of the items listed to clean a little bit because I don't want to see it all.

  BUT:
  I have now six items/places to the left.  I want three of them to stay.  I would like to 'Remove' the other three, but the option "Remove from this list" DOES NOT WORK!

  I tried:
  -Manually remove items/locations...   Always in the list.  So I put them back
  -Search for places objects in a windows search to see if they appeared in a file list somewhere that I could remove a manually.  No foumd.

  HOW to REMOVE THESE UNWANTED ITEMS/LOCATIONS in the list of Windows Explorer?

  Thank you.   -TomE

  NOTE: A second problem is that I couldn't use a sign less "-" to exclude elements of my research, when I used Windows Search.  I tried to use '-internet "to exclude references to Internet Explorer.  It did not work.  There for me in the past.

  Hello

  Right-click the Start button, and then select Properties.

  In the privacy section, remove the check mark from the option "store and displayrecently open items in the Start Menu and the taskbar" . CLIck apply/OK.

  Check the list of shortcuts in Windows Explorer and recent items section should be empty.

  Go back and re - activate this option.

  NOTE: this procedure will empty all the list Jump list recent items as well as the recent items on the Start Menu.

  I hope this helps.

  Thank you for using Windows 7 Ronnie Vernon MVP

• Access list ASA Error | ERROR: % incomplete command

  Hi all

  I am trying to enter the following rule but I get an error message, I have a similar rule already inside the firewall, so I don't get really what is the problem and how to go about troubleshooting. Can anyone help?

  acl_inside list extended access allowed object-group 16-09-08F 132.235.192.0 255.255.192.0 eq https Journal

  (network-config) # access - list extended acl_inside permitted object-group$

  acl_inside list extended access allowed object-group 16-09-08F 132.235.192.0 255.
  255.192.0 log https eq
  ^
  ERROR: % name host not valid

  SAME THING WITHOUT JOURNAL

  (network-config) # access - list extended acl_inside permitted object-group$

  acl_inside list extended access allowed object-group 16-09-08F 132.235.192.0 255.
  255.192.0 eq https
  ERROR: % incomplete command

  SAME STUPID MISTAKE,

  THE SIMILAR RULE;

  # ACCess-list HS | I have 132.235.192.0
  permit for line acl_inside of access list extended 2767 tcp object-group 16/06/29 X-2 132.235.192.0 255.255.192.0 eq https

  ???????

  I'm not sure that this ensures a case of cisco?

  FW100ABCx (config) # 16-09-08F object-group network
  FW100ABCx(config-Network) # host network-object 172.191.235.136
  Add items (host to network-object 172.191.235.136) to grp has failed (16-09-08F); the object already exists
  FW100ABCx(config-Network) # host network-object 172.191.235.135
  Add items (host to network-object 172.191.235.135) to grp has failed (16-09-08F); the object already exists
  FW100ABCx(config-Network) # host network-object 172.191.235.134
  Add items (host to network-object 172.191.235.134) to grp has failed (16-09-08F); the object already exists
  FW100ABCx(config-Network) # host network-object 172.52.134.76
  Add items (host to network-object 172.52.134.76) to grp has failed (16-09-08F); the object already exists
  FW100ABCx(config-Network) #.
  FW100ABCx(config-Network) # acl_inside of access allowed object-group list $

  acl_inside list extended access allowed object-group 16-09-08F 132.235.192.0 255.255.192.0 eq 443
  ERROR: % incomplete command

  Hello Hassan.

  You're missing the key word of Protocol (tcp/udp)
  Try this:

  the object-group 16-09-08F network
  host of the object-Network 172.191.235.136

  acl_inside list extended access permitted tcp object-group 16-09-08F 132.235.192.0 255.255.192.0

  Concerning
  Dinesh Moudgil

  PS Please rate helpful messages.