replacement of card mother HP DV9700 help

Similar Questions

• Replaced the card mother zd8000 and need a hand, help please...

  Hi all

  I just replaced the motherboard on our HP zd8000 (pentium 4 3.0 ghz, 2 GB ram, Win XP) with an opportunity tested but good MB and need help with the following.

  (1) I cannot play DVD movies as the error 'no dvd decoder' present which was not a problem before now?  Where can I get a free decoder that works as Windows displays only paid versions?  We have the drive to dvd with lightscribe. SOLVED! CNET has DECODER.

  ---------------------------------------------------------------------------------------------------------------------------------------------------------------

  (2) internal temperature, according to SpeedFan, revolves around 140 degrees with just surfing the Internet.  Is this a normal temperature because I have only one of the three fans running on the laptop?  Is in any case to all the three fans running to be sure there is no problem?  I'm positive, I plugged everything but still once a single fan seems to work?

  (3) I discovered that some of the pins were damaged in the card reader.  I can get the seller to give me a discount, not intend to tear apart just for it, but is there the concerns of short or otherwise?

  (4) our battery arrested charge years ago, these were known as such, but I bought a new one last year and hope that the replacement MB would load it again.  No luck though.  Can I do, update of BIOS etc, in order to make the battery charge?

  (5) whatever it is you people can think for me to test to make sure the new motherboard is working correctly?

  Thank you, Ralph

  PS, It's a replacement card correct according to the serial numbers of MB.  Everything seems to work properly except mentioned.  Our graphics came out on the original MB.

  Some of the sons had grown out of the harness that connected the two other fans.  I double checked and replaced these so now the laptop works quite a bit cooler.

  EVERYTHING IS GOOD TO GO!

• Cannot install Recovery on replacement discs card mother p7 - 1017c

  I had a mother fail on me. At first, I thought it was the operating system, but after trying the recovery discs I ordered at HP, I thought it was my motherboard.  I thought I could replace it with the same. Bought the same exact motherboard from Ascendtech. I installed the Board of Directors. Then I inserted the recovery disk and got the following error message. "This computer does not support the system recovery media. You are not able to restore the system with the media". Called HP support and they basically said that I have to take the PC to an authorized service center, so they can program the new motherboard at the cost of about $200 the representative told me. I'll have to buy another copy of Windows 7? And it will install on the new motherboard. (Representative of HP was that it wouldn't) Help, please!

  Hello

  You should be able to buy cheaper Windows 7 (called OEM version) with a new motherboard OR download Windows 7 and use the product key on your computer to install. You must contact Microsoft to activate after that. Please use the following link to download:

  http://www.mydigitallife.info/official-Windows-7-SP1-ISO-from-Digital-River/comment-page-1/

  Kind regards.

• How to replace the card mother, processor and memory in my office without having to buy a new code for Win 7 Utimimate detail?

  In January, my original motherboard died and I replaced the jury only with other printed device using all my old components. When I started to the top of the first time I was warned that my version of Win7 is not valid. (I had used since I bought it in August 2010 without any problem) So I bought a new Windows 7 Ultimate full retail Microsoft online to get going again. Now, 3 months later, it's blue, screening and stop randomly. The Board of Directors, the memory and cpu are all about 7 years and I want to update the new and updated components. How can I do this without having to spend another $207 for a new copy of Windows 7?

  When you transfer the license to a new motherboard, reactivate just by phone, as you said that it is a full commercial license:

  How to activate Windows 7 manually (activate by phone)
   
  1) click Start and in the search for box type: slui.exe 4
   
  (2) press the ENTER"" key.
   
  (3) select your "country" in the list.
   
  (4) choose the option "activate phone".
   
  (5) stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
   
  (6) explain your problem clearly to the support person.
   
  http://support.Microsoft.com/kb/950929/en-us

• What should I do after having replaced the card mother i - pod?

  I replaced the motherboard of I have my daughter 7 Gen 160 GB iPod and when I turn it on the screen is completely gray. I think that I have to download an operating program. However, my PC does not recognize the iPod to allow me to access it. When I connected the former Council (replaced due to the connector of the battery come off) the display shows "battery charging please wait."

  How can I get my PC to recognize my I - Pod with the new motherboard was connected?

  Are you sure that the "new" motherboard is everything ok?

  Try to put it in DFU mode: plug it into your computer. Hold the power and select buttons together for 12 seconds. It should be a charge in the battery. See if the computer recognizes then.

• replacement of card mother m6 HP envy without replacing the cpu or gpu

  I have a computer laptop envy m6 1102 - its who has problems with the motherboard that needs to be replaced
  can I replace it with replace them it's cpu/gpu?

  Eng_Mido wrote:
  

  Thanks, but are there parts that can be replaced in the motherbard or I have to replace it? Thanks in advance.

  Well, after getting to the motherboard there is in fact only the heatsink and the CPU to replace. You must remove them and install them on the new Board of Directors. You need to install the new board inside the base (bottom of box) connect all the cables and son back etc...

• I can't recover my system (DV6000) using recovery discs after replacing the card mother/HARD drive

  I have a DV6408nr (windows vista Home premium) I had to replace the motherboard and hard drive. When installing the new motherboard (same part No.: 443775-001) and insert the recovery (bought from HP) discs that I have, I received an error message stating that the PC could not be recovered using my disks. The serial numbers on the label service and in my bios do not match. When I entered the serial number of my bios in HPpartsurfer, he said that the system is a DV6449us. I already checked my RAM and HARD drive is brand new/not formatted. I used these recovery discs (manufacturer: 483905-003/483906-003) successfully before on other flags of DV series. Is there a reason why these discs should not work on two motherboards in the same system with these similar specs? What should I do to get my system recovered?

  The number of the motherboard and other show information in the bios of the new Commission?

  The numbers do not match the recovery disks or information is missing in the bios.

  If it's really a mismatch, then you will need to find the good recovery disks or use a Dell installation disk operating system and use the product key from the sticker on the laptop to get activated, and then manually install the drivers.

  If the bios tattoo is damaged or missing information only a used HP Center can then fix the tattoo.

  check your private messages

• Replacement card mother Qosmio G10

  After replacing the card mother a Qosmio G10-120 original Win Xp MCE with the official update (FC43S1 A5A001749010 P000454980 jury), some problems have arisen:

  1. second HARD drive internal no more seen.
  2. all buttons stop "standby/disable rebooting the computer" do not completely take effect (office closed way unexpected but manual power button continues to show the color blue and portable remains active).
  3. always on cooling fan.

  Upgrade the motherboard consisted of:

  1. creation of new channels DMI Council (in particular "Model name" field was set to "Qosmio G10").
  2. loading the CD-ROM TCN0000006 official update tool.
  3. no recovery BIOS or EC/KBC.

  Any idea?

  I m wondering how you did update the information in the DMI?
  As far as I know that the Toshiba authorised service provider is able to update information DMI as the model name, version number, etc. using utilities and special tools.

  I googled for the motherboard part number, you have deposited in your original thread, and it seems that this motherboard has been developed the Qosmio F15 series.
  So maybe his bad card mother

• After some time, my screen goes black have to re boot. It is only on I pc the other pc on the same monitor works okay my video card is on the card mother all ansawers would help t / you rkfjr

  After some time, my monitor goes black have to re start at 5 min to 2 h said mge device is grapish until this day.   It is only on I pc the other pc on the same monitor works okay my video card is on the card mother all ansawers would help t / you rkfjr XP HP pc 1.3 gh 512 ram 120g hd

  Assuming that the integrated graphics controller is OK, try the following:

  Launch a command (as a Runas administrator) window and enter the following commands in it:

  powercfg-h off

  powercfg/change-standby-timeout-ac 1440

  The first command turns off "Feature of putting into hibernation"

  The second command replaces the timeout stansby 24 hours when the system is connected to AC power.

  (The number is in minutes).

  Good luck.

• Lenovo g560 card mother SAV helping crash do not now what to do

  Hi, I have purchase a lenovo laptop g560 June 2, 2010. After a low card mother get corrupt.now my system will not start. I call on the Indian head off with call id = 4270018809 and they sujjest me orders to go to the Service Center in noida. After going there they put my phone for 1 week and after that 1 low they say we do not have the mother board.and they ask headquarters, to this uncertain time and I can take laptop without getting repaired.now what can this laptop is not replaced anywhere help me its urgent. I thank in advance

  Solved

• Inspiron One 2020 new card mother help

  Greetings & Salmenella

  The high memory slot on the motherboard of my Inspiron One 2020 beeps stop known, two beeps of intervals. Any memory I put in the continuous ringing. It stops if I have a memory stick into the lower slot.

  I need help on the verification of the correct mother card to purchase or if it is a card mother Dell different that I can spend which will enter in the box. I don't mind if I have to make the cuts or small holes in the back plate, since I already have the holes for a tuner card, I bought after that I bought the model which had no openings for cable TV.

  I really don't want to go buy a brand new for a slot with memory 4meg bad computer. I have a solid state, 8 GB RAM and 2 GB of RAM, it runs fast enough that I do not have to buy a new computer. But losing that 4gigs of ram in the bad memory slot. Holy Ding Dong, the hard drive takes forever to stop making noise, surfing slows down and compilation and writing of visual basic for class takes forever.

  Now for the short version.

  What is the correct motherboard model to replace an Inspiron One 2020 or is there a model of mark liked that a motherboard will suit my AIO home and get all my guts of the computer. I have a 5-2390T UC iCore.

  Love,

  Stu

  Any advice for this model are the same - but nothing else that will fit the original.

  www.amazon.com/.../B00I9OQQ7U

• Help with the new card mother and Vista problem?

  So yes, I got a new card mother and cpu, it seems to work fine except the loading of windows! I said to reinstall vista, however, my computer never came with a vista CD, it was already installed. all I have is restoring 3 DVD. What I could find on the internet is a: A: I need to spend money for a BONE

  b: use linux

  work of the restore cd to reinstall the OS, so I can use my new motherboard?

  So yes, I got a new card mother and cpu, it seems to work fine except the loading of windows! I said to reinstall vista, however, my computer never came with a vista CD, it was already installed. all I have is restoring 3 DVD. What I could find on the internet is a: A: I need to spend money for a BONE

  b: use linux

  work of the restore cd to reinstall the OS, so I can use my new motherboard?

  Hey icuhavoc

  are recovery disks to reinstall vista with the original hardware installed if I understand you correctly know what records you need to know a set of manufacturer's recovery disks

  If it is pre-installed this is an oem license and does not change unless you did it in consultation with the manufacturer of models of motherboards and processors

  Walter, the time zone traveller

• the upgrade card mother DM3-Pavilion

  Hello

  My 4 year Pavilion dm3, recently died on me. It's a little elegant machine, I wanted to wear around and who was always OK for occasional daily tasks. For these reasons and others, I would at least try to replace the defective motherboard and revive.

  The model I bought is a dm3-1003tx exotic model (bought in Thailand, especially with a keyboard QWERTY/thai), with Intel SU7300 and discrete nVidia GeForce G 105 M graphics chip.

  Given that the original motherboard is not easy to find (PN 584079-001, only a couple of bids on ebay of the Japan), can someone tell me:

  -If it's OK to replace it with an another based SU7300 of motherboard (can be with or without the nvidia chip - I really don't need it).

  -or even better upgrade to a motherboard of SP9300 based to get a performance gain? If so, should I expect any change (it looks that the consumption of energy and the frequency of the buses are higher with the SP9300 then maybe RAM...?)

  Is there any tool available around compatible HP part numbers?

  Thank you

  No, there is not a matrix of cross, useful reference because it would be. I think that HP is simply too many different models and parts for someone to keep track of it all. HP Service is inspired by replacement with the same part number so their internal service people wouldn't even have much use for such a thing, just us end users.

  Motherboards have the processor soldered to the and there is only a single part number for the fan/radiator Intel stated so I would say that if you replace your motherboard with it:

  580663 001

  with the SP9300, you'll be able to reuse your fan/radiator. In the case where you don't have it here is the repair:

  Manual

  All models use the DDR2-800 memory and accept up to 8 GB. Different motherboards all seem to have the same ports and such and will have the same anchor points. You could even theoretically install a card mother AMD-based, but this would require to reinstall an operating system, and I wouldn't trade an Intel processor for an AMD processor in any case unless AMD have been much cheaper. A Committee from AMD would also require a different radiator, however.

  You can buy the SP9300 motherboard for $45 shipped on eBay:

  http://www.eBay.com/ITM/580663-001-HP-Compaq-motherboard-Pavilion-dm3-Intel-laptop-W-SP9300-CPU-581467-0-/400445142883?PT=motherboards&hash=item5d3c63f763

  The same seller also has the SU7300 for a few dollars less:

  http://www.eBay.com/ITM/584078-001-HP-dm3-1000-laptop-motherboard-w-Intel-SU7300-1-3GHz-CPU-/400600978029?PT=motherboards&hash=item5d45add26d

  I bought a little of this seller and it looks like they have a lot of them on the spot so must have dismantled a certain dm3s. Maybe if you call them they can steer you in a way or another based on real practical experience. I confess that I have the opportunity to work on this exact model.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Compaq CQ58-260SA: upgrade the processor on a card mother HP1858

  I'm looking to upgrade the current CPU Intel Celeron B830 since my laptop Compaq CQ58-260SA.

  I have contributed up to 8 GB memory, the laptop has a card mother/Motherboard HP 1858. Which I believe holds the G2 plug.

  I searched high and low online to see what the replacement of CPU max/implementation to date for this motherboard

  Can anyone help please

  Hello

  The motherboard has Intel HM70 Express chipset only supports Celerorn or Pentium processors.

  Specifications of product PC portable Compaq CQ58-260SA | HP® Support
  http://support.HP.com/ph-en/document/c03501719

  The mobile Chipset Intel® HM70 Express family chipset series Intel® 7, providing integrated USB 3.0 on a single chip - Intel® microarchitecture (code named Sandy Bridge and Ivy Bridge) and supports the Pentium® and Celeron® processors. The Chipset Intel HM70 provides:

  http://www.Intel.com/content/www/us/en/chipsets/value-chipsets/mobile-chipset-HM70.html

  Intel Pentium 2030 m is the most powerful possible to install.

  http://cpuboss.com/CPUs/Intel-Pentium-2030M-vs-Intel-Celeron-B830

• Problem of card mother-suggestions

  I have a Desktop Pavilion p6310y and I lost my second mother. He has a Paragon M2N78 - motherboard and said that it is the only one that can be used on this computer. Does anyone know if there is another motherboard that can be used on this computer? It has a processor AMD 2.8 ghz and 6 GB of ram. I really want to buy a new computer, I just want to see if it can be resolved.

  For any help or suggestion would be appreciated.

  Bob

  Bob,

  Here are the specifications of your desktop HP Pavilion p6310y and its card mother M2N78-(Violet6). Please note that this model uses the 'VIOLET6' of the M2N78 - motherboard version and not several different version called M2N78 - LA. This model came from the factory with an AMD AM3 Athlon II X 4 630 and 6 GB memory DDR3.

  While you can replace the motherboard with a new one, Windows will become "not authentic" and you will need to purchase a new copy of Windows. Other problems that may arise,... include your recovery discs HP will no longer works, back plate I/O may not match, mounting motherboard can not align the studs, etc.. When installing a new copy of Windows, you will lose all 'value-added' original HP supplied with your computer software.

  If you're OK with every possible question of a motherboard out of factory usage, consider these cards mothers AMD AM3 + who is responsible for your AM3 Athlon II X 4 630 CPU and DDR3 memory.

  Please send Bravo