Replacing drive in XP Home

Similar Questions

• need to replace drive for A495

  I changed from XP to 7 and I can't find my disk for my A495. Can I download or get a replacement drive.

  Thank you, Dennis

  http://www.USA.Canon.com/Cusa/support/consumer/digital_cameras/powershot_a_series/powershot_a495

  Click on "Drivers and software".

• Replaced drive now in lieu of a State, does that mean?

  I had a drive fail in a PV hanging off a PERC 6, and it rebuilt to the hot spare fine.  Now I'm put a new drive in the slot where the failed drive was, went into the RAID BIOS where I assumed it would be in a Ready state and waiting for me to mark it as the new hot spare, but it is in a Replacing state, not Ready, so I cant mark it as the new hot spare. Does this mean its rebuilding from the hot spare to that new drive and then the former hot spare now live drive will go back to being the hot spare again?
  

  Hello rjo80,

  Yes the hot spare is to copy the data on the replacement drive & once it's over then it will go back to being a spare disk.  On the PERC card, there is a feature that recalled the copy that has been activated & with that enabled that is why u who sees in the PERC bios.

  Please let us know if you have any other questions.

• replaced drive perc5i

  Hello

  I recently replaced a drive in a poweredge server 2950 with perc controller 5 / i running RAID-5. There are 4 disks on slot 0 and 2 drives on the connector 1.

  Replaced drive is 0:0:1 and is stuck in the ready state.  I have tried to add as a hot spare but can't seem to get this drive to come online.  While checking this point, disc 1:0:5 is also stuck in a ready state, and not online. (I think that this was replaced by a former employee in the past)

  1. can you someone explain global hot spare vs dedicated emergency and if I want to drive one.  I find this very confused and do not understand the reading that I still find.  One even told me that the replacement drive would only pick up the slack for the connector, to which it was attached?

  2. how to make disk 0:0:1 online and 1:0:5 online?

  3. the disk 0:0:0 is also in a State of predicted failure and I have a disc for this but I would like to firstly with these other two.  I understand, that it is unlikely to have two failed disks at the same time, but we are dealing with 2006 readers

  Any help would be appreciated.  I apologize in advance for any terminology that I hacked upward and also for my ignorance on this subject.

  v/r

  Blair

  1.

  Dedicated hot spare: A disk that is ready to take the place of a disk that fails - any disk that is part of the table that is assigned the rescue. If you have a RAID 1 and RAID 5 3x1TB 2x1To, you can assign the emergency to protect ONLY the RAID 5, so if a RAID 1 drive fails, it will not rebuild, but if a disk in the RAID 5 fails, it will rebuild in who has no place to drive.

  World Relief: A disk that is ready to take the place of any disk that fails - a disk that is part of a table. In the scenario above, you can assign the disk as a global hot, then regardless of what table failed disk belongs, the hot spare will rebuild in its place.

  A hot spare must be at least as large as the disk, it must replace, and a hot spare must be the same type of disk (SATA/SAS) than the player he must replace.

  bterry213

  One even told me that the replacement drive would only pick up the slack for the connector, to which it was attached

  This is not true.

  2.

  It depends on your configuration. Obviously you are not running just a single RAID 5, or with two drives in the State LOAN, your data table / would be gone. So, we need to know exactly the configuration that you are running.

  3.

  Yes, you should start with the other two, with fully redundant table and fail in good health before the disc pred. You will need to FORCE it offline before replacing... WHEN you are ready to do so.

• I need a replacement CD of XP Home for a new installation on a new hard drive.

  My old hard drive failed and I replaced it. I have the product key still on the Tower, but loses the original XP came with the pc disks.  Is there somewhere I can download XP home or should I buy the CD?

  Hi SarahMowery,

  I suggest you follow the article in the Knowledge Base Microsoft for more information.

  How to replace hardware or lost, broken, or missing Microsoft software

  http://support.Microsoft.com/kb/326246/en-GB

  I hope this helps.

• Windows will not activate after the hard drive is replaced on Windows 7 Home Premium.

  Recently, I had a hard drive crash and had to replace my hard drive. I took it to a computer to fix store, and they have installed and gave me a new drive for windows 7 Home premium. However, it was not approved, and I have no key validation. How can I validate windows now?

  Search for your key on the side of an office or downstairs (sometimes inside the battery case) of a laptop.

  How to activate Windows 7 or Vista manually (activate by phone)
  http://support.Microsoft.com/kb/950929/en-us

  1) click Start and in the search for box type: slui.exe 4
  (2) press the ENTER"" key.
  (3) select your "country" in the list.
  (4) choose the option "activate phone".
  (5) stay on the phone * do not select/press any option * and wait for a person to help you.
  (6) clearly explain your problem to the support person.
  (7) the person must give you a confirmation ID, copy it down on paper,
  (8) check that the ID is correct in reading the support person.
  (9) to enter the ID number, then click 'Next' to complete the activation process.

  ----------------------------  Alternatives -------------------------------------

  To enable the use of the phone
  1. open Activation of Windows by clicking on the Start button, right click on computer, clicking Properties.
  then by clicking on activate Windows now. ?

  2. click on show me other ways to activate.

  3 type your Windows 7 product key, and then click Next.

  4. click on use the automated telephone and then click Next.
  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  5. click on the location nearest you from the drop-down list, and then click Next.

  6. call one of the available phone numbers listed. An automated system will guide you through the activation process.

  7. When prompted, enter the installation ID that is listed on your screen in your phone keypad.

  8 Note the confirmation ID the phone system gives you.

  9. under the terms of step 3, type the confirmation ID in the space provided, click Next, and then follow the instructions.

  10. If the activation is not successful, stay on the line to be transferred to a product activation agent who can help you.

  Microsoft Activation centers worldwide telephone numbers:
  http://www.Microsoft.com/licensing/existing-customers/activation-centers.aspx
  (This site is for activating Volume License, but if you call, they will help you)

  The phone number is not working:
  Microsoft Wordwide contacts: http://www.microsoft.com/worldwide/default.aspx

  Register Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/help/register
  Register Windows 7 and you automatically receive a series of three welcome to Windows e-mails
  filled with tips, creative tips and other information to you help get the most out of Windows 7.
  You also get a subscription to the monthly newsletter of Windows Explorer,
  where you will find other tips and tricks, as well as special offers.

  Activation and registration of a Microsoft product
  http://support.Microsoft.com/?kbid=326851
  Windows activation: (888) 571-2048

  Learn about Activation:
  http://TechNet.Microsoft.com/en-us/library/ff793423.aspx

  J W Stuart: http://www.pagestart.com

• How can I get Windows XP Home edition OS replacement drive

  my driver disk and OS xp are damaged I can't start windows, I need a replacement cd

  Good luck, try to find a. Check Amazon.

• Replace drive HARD laptop HP bf69WM 2000

  Hello

  I recently acquired the dead laptop HP 2000 model bf69WM with a hard drive (error in the log of BIOS: 03F0). I studied a replacement and found gaps in the Service Guide. He says that the supported drive has an RPM of 5400 in section 7200 in another. The drive 5400 RPM is 9.5 mm. The 7200 disk is 7mm. The HARD death drive is a Toshiba 320 GB model MQ01ABD032.

  If I replace with another Toshiba 5400 RPM, 9.5 mm drive all should be well, (I assume apples to apples). If I replace it with the 7200 RPM drive 7 mm: has) the highest ROTATION speed will cause more heat and perhaps premature? (b) will it be should I buy another drive Assembly to support the drive of 7 mm?

  I'm looking to a Western Digital drive. In addition, this particular model does not support larger capacity drives or SSD?

  Thanks in advance for any information.

  Is a license for your laptop to Windows 7 or Windows 8? Can't help much with Windows 8, but if you have Windows 7 Home Premium 64 bit here is a link to an .iso that is a legal copy of the operating system that you are naked.

  http://MSFT.digitalrivercontent.NET/win/X17-58997.ISO

  This will work only if your laptop came with Windows 7 installed. If it is Windows 8, you will have recovery media order of HP.

• Could not restore Windows 7 for replacement drive

  HP Pavilion 6267c running Windows 7 64 bit would not start.  Diagnostic said failed to find the startup disk.  Replace 750 GB drive with Seagate Barracuda 1 TB drive.  A ran disk original restoration and after initial installation, but I have the following message:

  Windows Setup could not configure Windows to run on a hardware on this computer.

  Retries of installation with the same results.

  any help is appreciated.

  Hello

  Before you try the following, make sure that you can always read the activation code on your label Windows COA (5 blocks of 5 alphanumeric games).

  Assuming that it's just a problem with the recovery process, it is a job before right around if you have (or can borrow) an installation disc Windows 7 at retail which is exactly the same version as your OEM installation - IE your PC came with Windows 7 Home Premium 64-bit, it comes to version exact commercial that you would need.

  If you don't have access to a retail disk, you can create an installation disk yourself using another PC - just download the good Disk Image from the link below and use an app like ImgBurn to burn the ISO correctly on a blank DVD - a guide on the use of ImgBurn to write an ISO on a disc is here.  These Images are clean and a well respected source, however there are only limited versions available.

  Windows 7 sp1-iso-official-32-bit-and-64-bit

  Use the disk to perform the installation, enter the activation key of Windows on the label of the COA to demand and when the installation is complete use the 'method of phone", described in detail in the link below to activate the operating system - this method supported by Microsoft and is popular with people who want just a new installation of Windows 7 without additional software load delivered normally with OEM installations.

  http://www.kodyaz.com/articles/how-to-activate-Windows-7-by-phone.aspx

  Additional drivers, you may need can be found here.

  Kind regards

  DP - K

• Replace drive HARD system with Samsung EVO SSD 1 TB of HP ENVY 17 - j005tx laptop computer

  Hi all

  Wanting just a few tips on how to migrate and replace the system drive without having to reinstall everything again.

  The Migration of Samsung tool work?  When I check my HDD in the laptop there 5 partitions...

  The HARD drive, I would like to replace a the following Partitions:

  400 MB (Recover Parition)

  260MO (EFI Partition)

  904 GB (drive c :) - NTFS)

  350 MB (recover Partition)

  25.5 GB (drive D: Recover - NTFS drive)

  According to the Samsung User Guide data Migration tool, he mentions the following:

  http://www.Samsung.com/us/support/owners/product/MZ-7TE1T0BW

  6 recovery OEM partitions, at the plant by computer makers, cannot be replicated. However, if the PC is manufactured by Samsung and SRS (Samsung Recovery Solution) 5 or 6 is installed, the recovery partition is automatically cloned. (Not supported in versions prior to SRS 5)

  How can I migrate all recovery OEM as well as partitions C: and D: partitions?

  Thanks in advance

  Jim

  Laptop HP ENVY 17-j005tx, HP ENVY 27 - k001a, HP ProLiant MicroServer Gen8 G2020T, HP MediaSmart EX495 Server tilt, HP MediaVault 2020, HP ENVY 120 AiO Printer

  If you burn the recovery DVD, you don't need the recovery partition... they hold the same data. I try the clone on the new drive and see if it works. If it isn't then you still have the original drive and nothing has been lost. Reported problems with the migration of Samsung software. Personally, I use Acronis True Image Home for cloning, and it is not.

• Windows Vista Vista replacement drive?

  Several years ago, I bought a laptop Sony with Windows Vista preinstalled.  I've then upgraded to Windows 7 Ultimate when it came out.  I was recently infected by a virus that froze my computer and I had to wipe the hard drive but have no disk Vista replacement.  How can I get these?

  Hello

  Contact Sony for a recovery disc.

  http://eSupport.Sony.com/us/p/select-System.pl?model_type_group_id=10

  "How to replace Microsoft software or hardware, order service packs and replace product manuals.

  http://support.Microsoft.com/kb/326246

  Some manufacturers have more available Vista recovery disks.

  If this happens, you may need to try this instead:

  You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.

  Other manufacturers recovery DVDs are should not be used for this purpose.

  And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs

  Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  And once the operating system is installed, go to your computer manufacturer's website and get the latest drivers for your particular model or laptop computer.

  And phone Activation may be necessary when you use the above installation method.

  "How to activate Vista normally and by Activation of the phone '

  http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html

  See you soon.

• replace drive HARD w / Win 8 with the new drive HARD w/Win 7

  Just bought a laptop HP Pavilion 17-e067cl of COSTCO. I want to remove the factory installed HDD with Win 8 and the factory load on it and replace it with a new HARD drive and load Win 7 on it

  Is there something in the BIOS that would prevent me from doing this? If so, the parameters can be modded to accomplish my plan?

  I intend to use a same naked drive and load Win 7 on it.

  Will be a new copy, the retail sales of Windows 7 Home Premium SP1 64 bit Full System Builder License and media, 020250 GFC (1 machine, 1 license) be installed the correct version of the operating system. I want Home Prem

  My intention is to keep the original HDD with Win 8 warranty questions arise in the future or will be the wedding of the motherboard is a problem?

  Details for laptop:

  Prod #: F9L64UA #ABA

  HARD drive: ST750LM0 22 HN-M750MBB SATA (Samsung)

  BIOS: F.22

  Sys Board: 1984 01.13

  Memory: 8GB Samsung 1600 MHz SODIMM

  CPU: AMD A8 - 5550 M APU with graphics Radeon (TM) HD

  WARNING: my last cert has been on Win XP, so I'm way behind the curve on 8 to win.

  Thanks in advance!

  hardwired56,

  Please indicate if you have some problems to get into the BIOS or open Bay hard drive of the computer...

  For hard removal and replacement please see page 49 of the HP Pavilion 17 TouchSmart Notebook PC HP Pavilion 17 Notebook PC Maintenance and Service of Guide.

  If you have any other questions, feel free to ask.

  Please click the White Star of KUDOS to show your appreciation

• need to replace drive for: Adobe Creative Suite Master Collection

  Hi, my computer crapped out when it has been updated to windows 10.  Quire some of my programs have been disabled and or terminated, including my Adobe Creative Suite Master Collection. [deleted by moderator - this is a public forum - serial number do not share your serial number in public!], bought in 2012. I can't locate my drive home and grateful for the help, either buy a replacement disk or download the program.

  so please get back to me.

  Thank you

  Al canino

  [personal information deleted by Moderator]

  [Moved from creative cloud for teams in the Creative Suites - moderator forum forum]

  It would be CS6.

  You can download CS6 Adobe here.

• iCloud Drive to the home screen?

  Hello dear friends,

  I tried everything, but it seems that I can't see "Show on home screen" option for my iCloud Drive... Instead, I have just this screen without the option to activate the drive on my homescreen to iCloud.

  Do you have any idea on this issue?

  Any help will be much appreciated.

  Thanks in advance

  

  I have not either - this option on my iPhone but I have the app for iCloud drive visible on page 2 of my home screen. I think this setting my have been removed in iOS 10. Have you checked all your home screens to see if the application is visible? Also try to use the search to find it.

• I customized my ff and edited a few scratches here and there, but after each reboot ff replaces! and my home/arrow/refresh page buttons are really becomeugly

  Hello

  I use FF for years, but now it is starting to disappoint me! I adapted my FF and added some scratches here and there, and normally, everything else as I want/set but... until a few days... every time I restart FF it replaces some scratches left to right and vice versa! Very annoying!

  Another problem is that my "home/arrow page (rear) / refresh" buttons have become so ugly and small and no I don't thick 'buttons' in the options.

  I don't really know what is the problem, but now it is starting to be very boring!

  Here's a printscreen BEFORE FF it's ruin: look how beautiful the buttons are and other things!

  [img] http://I3.lulzimg.com/1919c1d2a9.jpg line

  And here are FF ugly with ugly buttons and in the good uppercorner strips left the adblockplus should be on the right, but it is replaced by its me after that I restarted FF each time!

  I admit that when I saw that it replaces the scratches I UN-and/reinstalled FF and after that the buttons becomes too ugly....

  What could be the problem?

  This module has been modded to cancel the theme changes in Firefox on Vista and Win7 14.
  
  https://addons.Mozilla.org/en-us/Firefox/addon/cstbb/