Reset zero Aironet 1242AG

Similar Questions

• Help with a Cisco Aironet 1242AG

  Alright. So, I want to start by saying that I have what I consider to be the basis of knowledge of network management. I recently got a Cisco Aironet 1242AG WAP. I realize that this is not a stand-alone router. I would use it as an extension of my current router. From now on, the status light is alternating colors. If I understand correctly, it can not find the controller. I cannot telnet inside, or use web browser interface. Both say that the connection is not available. However, when I check my DHCP from my router table, I see that an IP address has been assigned to the MAC for the WAP. I tried to do a factory reset holding MODE until I plug the power supply and wait until it turns amber. After a few minutes and go through a few changes led, it goes back to the alternating colors on an ongoing basis.

  I don't really know where to go from here. Help, please.

  Thank you

  Kris

  Radios allow without a ssid that are attached to them. You will need to create your ssid and then fix to the interface radio. assignment of an address to the British Virgin Islands and setting a value default gateway on the device and you should be able to raise it.

• Aironet 1242AG GUI

  Hello

  I just got my aironet 1242AG. I configured the ip address of fastethernet 0. I tried to pass 1242AG GUI fastethernet 0. But I failed to get in the GUI. Is there another adjustment I have to make before I can access 1242AG GUI?

  Oh there, I'm new in the wireless field. :)

  I think that you configure the IP in bvi int and not fa, if you configure it to factory default. Also, I guess it's wap-based IOS and not LWAPP.

• M277dw: Reset zero problem using the USB to M277dw

  Hello, I'm just trying to see if anyone else has had this problem. I use the laserprinter HP M277dw and use a current running nine Imac El captain. If I print anything on my printer and then decide to reboot my computer for some reason any, if I keep the USB cable connected to my computer that is connected to the printer, the computer hangs on reboot. It is the same on a full stop to the low and new start up as well. It's almost as if the printer is not disconnected somehow when I shut down or restart. The solution I found is to unplug the printer USB whenever I have to restart or shut down and then reconnect to the computer up and running again. My feeling is that this is related to the El captain, but I can't say for sure. Anyone else see this problem?

  Hi @andrewdawson11,

  Welcome to the Forums of HP Support! I see that you have problems, turn off the Mac, it crashes on restart when the printer is connected by a USB connection. I will definitely do my best to help you. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  Run Apple updates.

  You download and install the latest drivers for the printer? If the latest driver is not installed, which can cause this problem. Here is the link if you have not already: HP Easy Start.

  Make sure that the correct driver is added.

  Click on the Apple menu, click System Preferences. Click on Printers & Scanners, highlight the name of the printer on the left side and right side of the screen it should show the name of the printer. (Laserjet M277dw)

  If the full name of the printer is not correctly, delete and add the printer name back from the list. Click on the sign - to remove the driver and then click on the + sign to add the driver might have to drop-down list to select the name of the printer to add a click.

  

  

  If the problem persists, try the following:

  Fix permissions of the drive on the Mac:

  Close all applications.

  In the Apple menu, click OK, click Applications, and then click utilities.

  Double-click disk utility.

  Highlight your hard drive / partition on the left.

  Click on check and then repair disk permissions.

  Restart the computer...

  Reset the printing system:

  Note: This will remove all printers in the print and Fax/Scan, any printer deleted can be re-added later by clicking the sign plus (+) symbol.

  Click on the Apple icon and then click on System Preferences.

  Click on Printers & Scanners.

  Make a right click (or Ctrl + click) in the left white side panel, and then click Reset printing system.

  Click OK to confirm the reset.

  Type the name and the correct password.

  Click OK to reset the printing system.

  Then click on the sign to add the driver, highlight the printer +. (you may need to click the drop down menu to select the printer name) Then click the Add button.

  Test the printer and try to restart the Mac again.

  If there is anything else I can help you, let me know. Thank you.

• Reset zero Srw2008p

  Dear all,

  I was working with my linksys Srw2008p switch and I changed the IP address of the management vlan and somehow, I can't access the web console. I tried to use the new and the old IP.

  Also, I don't give a name of user and password on my own. It was to have the default username "admin" and password empty. I tried to access the console with you / n "admin" and the password is empty, I cudnt get thru.

  Now I need to reset the device to factory (without web access or console) settings.

  If anyone knows a solution please let me know. (This device has any button of reset on it)

  I also appreciate if you could please give me the link to download the configuration for this device guide as I cudnt found on the web.

  Thanks in advance,
  ASJ.

  Since the default password does not work, I suggest do you a first password recovery you will be able to access the device and reset the settings manually.  to make password recovery, you will need to access the switch using hyperterminal.  with the power on self-test press the ESC key. a new option should appear on the hyperterminal and there should be an option for password recovery. Once perform you the recovery password, you can try to reset the device. I hope this can help you.

• Reset zero point to navigate to a different page

  Hello
  
  I want to reset an ITEM_VALUE on the Page [say Page 94] only when I'm coming from another page, I have a few buttons and select lists that will SUBMIT and re - direct to the same page. In this case, I wish that the value to be preserved.
  
  I had intended to assign NULL to the element in a process that runs BEFORE HEADER.but that this will work any time select which list and buttons are used to redirect to the same page... Please pass me the details that can help.
  
  Thank you.

  Hello

  You can do this:

  Create application component for example called G_LAST_PAGE.
  Create Application "After Header" calculation for this type of request "value of the element.
  Break-in to the calculation

  APP_PAGE_ID
  

  Then, in your page 94 create process "Before Header"

  Px_ITEM1 := NULL;
  Px_ITEM2 := NULL;
  Px_ITEM3 := NULL;
  Px_ITEM4 := NULL;
  

  And place it under certain conditions "the body of the PL/SQL function returns Boolean.

  IF NOT :G_LAST_PAGE = :APP_PAGE_ID
  THEN
    RETURN TRUE;
  ELSE
    RETURN FALSE;
  END IF;
  

  Example is found in your page 964 app 998

  BR, Jari

• Are all the tools you need to configure an Aironet 1242AG?

  I keep getting messages that my access point refusal to connect.

  I put on the same switch that I'm connected to (a C2960). I can see it get an IP address, I can ping, but I get a refusal on the web address. The fact that the said refusal to connect browser I think it's a permissions problem.

  I have the Cisco IPSU tool and when I entered the MAC it finds the IP address. I checked on the DHCP server. Shouldn't be able to hit the web interface of the access point by using the IP address that has been assigned? Am I missing something?

  My laptop is not a serial port so I'm a bit limited here. Any help would be appreciated!

  You must enter AP CLI to check/troubleshoot your configuration.

  You can use USB-serial cable to get access to the console, if you have only USB ports on your laptop

  HTH

  Rasika

• Equium A60 - I need to factory reset

  I have an Equium A60, I need to reset zero factory because it is very slow and has a lot of unwanted things about it. However, I need to keep all the I-tunes that is on. I have also no original discs etc to re program, and I'm not a total pc expert.
  Can anyone help?

  Hi Mark,

  The only way to get your A60 comes back to its factory condition is to have a set of a Service partner chartered Toshiba recovery disks. In addition, you will need to back up your I-Tunes (by copying them to an external hard drive if you have one, or else by copying them to a CD/DVD flammable).

  Note that the system from the recovery CD restore will erase the contents of your hard drive and you will find while the latest updates Microsoft etc. will be missing. You can doenload the Microsoft Update site.

  Personally, I would recommend just clean your system of unwanted content. The simplest approach would be to run a utility like CCLEANER (Google to do this, it's freeware). Then run a full scan of the system (from your existing package of anti-virus) and finally run an adware scan using Ad-Aware and SpyBot (Google for these, they are both freeware).

  Finally, go to the Add/REMOVE software control panel section and remove any what spftware/applications you don't want.

  Run a system utilities disk defrag tool and the work is done. Your A60 should be as good as new but with all the latest Microsoft Updates always applied.

  Kind regards

• Migration of thick Eager VM supplied zero supplied to lazy thickness to zero

  I noticed that you can change the disk provisioning on a Windows prompt to reset zero Thick - Provisioned LAZY to Thick - Provisioned HASTE updated but NOT the reverse.

  So, it won't change back to LAZY.

  Anyone able to confirm?

  No, it was to test why did not have backups. Thank you

• 18.0.2 open several tabs, but will not open sites in tabs.

  What's up with the updated version 18.0.2? It will open a 2nd tab, but does not go on the site. Repeated attempts result in the same thing. I stopped, restarted Firefox. First tap opens fine. 2 and subsequent tabs aren't going anywhere seems open but then just stalls out.

  Hello starmanjb, average try to reset firefox (this will keep your bookmarks and passwords) as described in Firefox Refresh - modules reset zero and parameters.

• House-sharing has stopped working on my AppleTV 4

  Apple TV 4 - A1625

  rMBP (end 2013)

  iTunes 12.3.2.35

  Home sharing my collection of videos iTunes worked and then it didn't.  It's the good Apple ID on Apple TV and the Macbook Pro.  The computer and the Apple TV are connected to the same network, and both see the strength of the complete signal.  I tried the following:

  1. signature and sharing of House on AppleTV

  2 singing and in iTunes home sharing

  3 signature and in the iCloud on Mac

  4 reset zero AppleTV to factory settings and his resignation in all

  AirPlay works very well.  I can airplay video Quicktime for the AppleTV, but if I go to the computer I get the message "Turn On iTunes home sharing.  It is turned on.  Then I disconnect and reconnect (Yes, with the same AppleID, the only one I have).  Nothing.  Œuvres music from Apple.  Works of iCloud photos.  Yet, I can't connect to my own library on my computer.

  It's very frustrating.

  You could try to restart iTunes on the computer or restart the network router.

• Printer print printing printer will not align. Worked very well, put in new cartridges and now will not align.

  My HPPhotosmart C5580 all-in-One worked very well.  Put in new cartridges and now she is not aligned.  Have you tried several maintenance task to get it to reset zero, etc, but nothing seems to work.  Help.

  This isn't a matter of Microsoft but a problem of HP; See http://h10025.www1.hp.com/ewfrf/wc/product?product=3575276&lc=en&cc=us&dlc=en&lang=en&cc=us. There are also Forums of HP Support for printers.

• HP Envy Ultrabook 6 t-1000 CTO: HARD drive is not displayed

  Hello.

  I had the Windows Blue Screen of Death (BSOD) once or twice when using simple everyday applications on my Ultrabook. The results were either not different on Mode without failure. After awhile, I started having 'No Bootable disc' error while starting up. Recovery (press F11) will not appear so. I tried the HP Diagnostics (by pressing F2 at startup) and Test the hard drive as well as the Test of memory shows PASSED on the formats of short or long.

  I tried the following:

  1. I did some research on Google and entered in the BIOS/Insyde utility (by pressing F10 at startup), loaded default installation (by pressing F9), saved changes and did a restart, but I get the error again.

  2. I downloaded Windows 7 64-bit Microsoft store, created a boot USB and plugged. I was able to access the Windows Installation Page, but he wouldn't show my hard drive at all.

  3. I find the support page of my product on the site HP and downloaded the latest drivers, put it in a USB device and booted up the system from the Windows Setup disc. On the page where it was supposed to show my internal hard drives, it showed only USB drives and there is an option "Load Driver" I clicked on and selected the driver files I downloaded from the HP website. Everything was going well until I chose iaStor.inf... this time, the system has hung up and the BSOD appeared with an error stating the file 'iaStor.sys '.

  My questions:

  1 if diagnostic Tests are passed, I can assume that the material is well?

  2. Although I already placed an order for HP recovery discs, I doubt if it could help because my HARD drive drivers seem to be missing. What is your opinion?
  3. is there a way to reset zero/reload drivers BIOS/Insyde utility?

  My system features:
  Laptop model: PC portable HP Envy 6
  Product no.: A9G58AV (the back panel laptop says A9G30AV)
  {Information}
  Processor: 2nd generation Intel Core i5 - 2467 M CPU @ 1.6 GHz + Intel HD Graphics 3000
  BIOS version: F.0D
  Total memory: 4 GB
  Operating system: Genuine Windows 7 Home Premium 64-bit
  HARD drive: 500 GB 5400 rpm SATA RAW 7mm hard drive with 32 GB WSSD faster reduction of the hard disk Cache

  Unfortunately at that I disagree with Paul and I think that you may be looking for a bad motherboard, but we would like first to try to remove the disc of WSSD 32 gig.

  Here is the Manual:

  Repair manuals

  See Page 40. Unfortunately, this model is a little difficult to disassemble, but measures are set out in the manual. If it is still under warranty, you can't do that. If the hard drive passes the test of F2 then I tend to think that it's not the hard drive.

• USB power surge

  I got an error message indicating the USB power surge/failure.

  Since then, all 3 USB on my laptop is no longer works. If I plug an optical mouse into it the optical light doesn't even come on making me think it's a question of power.

  In Device Manager, all the usbs show also operational (although when you select one and go to the power tab, it shows 0 under the power available.

  I'm worried I have fried my motherboard, but everything else works fine.

  any suggestions?

  
  

  Hello

  What you can do is to reset the usb hub. This will probably fix your problem and if it doesn't it is will also be useful in pointing to USB are damaged by the surge.

  First try these steps to reset zero USB hub and let us know the result. Here are the steps:

  USB controllers require that an IRQ be assigned. The IRQ line is assigned in the computer's BIOS, and usually IRQ 9 is assigned.

  Remove and reinstall all USB controllers

  To remove and reinstall all USB controllers, follow these steps:

  1. Click Start, click Run, type sysdm.cpl in the Open box, and then click OK.
  1. Click the Hardware tab.
  1. Click the Device Manager button.
  1. Expand Bus USB controllers.
  1. Right-click every device under the Bus USB controllers node and then click on uninstall to remove them one at a time.
  2. Restart the computer and reinstall the USB controllers.
  1. Plug in the removable USB storage device and test to make sure that the problem is solved.

  Reference:

  http://support.Microsoft.com/kb/310575

  Hope this helps,

  Steve <> Microsoft Partner

• Adjustment of antennas

  Hello!

  I have an aironet 1242AG access point, 2 x 2, 4 GHz (AIR-ANT5135D-R) and 2 x 5 GHz (AIR-ANT4941) installed antennas. I have the gateway lying on a rack near the ceiling. What is the best position for the antennas? Should they be right vertical or by creating a V shape (between the 2 same frequency)?

  I do not think that to get a big win out of this, but what are the guidelines?

  Thanks a lot for anybodys time!

  Hi Isabelle,.

  In your case "vertical right" would be the way to go. You might not really need two of each unless you are trying to give a cover type diversity. Take a look;

  You can use two antennas in Diversity mode, but not to cover two different cells/regions. For most installations, if you just use an antenna connected to the Right-hand/primary, RP - TNC connector you should be good, if you have obstacles in the area of cell, you can try to use mode Diversity (2 x? Antennas);

  When you use a pair of antennas with characteristics corresponding to ensure diversity cellular coverage in your establishment, the guideline is to put these corresponding antennas at one distance independently of the other which is equal to a multiple of the wavelength of the frequency that is passed. The 2.4 GHz wavelength is about 4,92 inches. Therefore, in order to support diversity on a radio of 2.4 GHz with two separate antennas, the antennas must be sufficiently spaced about 5 inches apart. The pair of antenna could also be spaced at multiples of 5 inches, but the distance between the two may not exceed 4 multiples: reflects the waves more far outside that are likely to be so distorted and different late spread that the radio could not work with them. Because each antenna is chosen by himself, both antennas should have the same characteristics of radiation and be placed to provide similar cellular coverage.

  The good doc.

  Multipath and diversity

  http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_tech_note09186a008019f646.shtml

  Cisco Aironet 2.4 GHz and 5 GHz antennas and accessories

  http://www.Cisco.com/en/us/products/ps6521/products_data_sheet09186a008022b11b.html

  I hope this helps!

  Rob