Router and VPN Client for Internet Public on a matter of stick

Similar Questions

• Please help router and vpn client

  Hi all

  I want to make a vpn between my PC (with version 4.8.02.0010 of the VPN Client) and a remote router (Cisco 2811) version of the software IOS 12.4 (9) T7 and the following configuration

  AAA new-model

  !

  local VPNCLIENT from AAA authentication login.

  local AAA VPNGROUP authorization network

  Hello test user name password

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group 3000client

  key cisco123

  DNS 62.42.230.24

  domain cisco.com

  pool ippool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  transformation-RIGHT game

  !

  map clientmap client authentication list of crypto list

  crypto isakmp authorization list grupo clientmap map

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  interface FastEthernet0/0

  DHCP IP address

  NAT outside IP

  IP virtual-reassembly

  load-interval 30

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface FastEthernet0/0/0

  !

  interface FastEthernet0/0/1

  !

  interface FastEthernet0/0/2

  !

  interface FastEthernet0/0/3

  !

  interface Vlan1

  192.168.4.1 IP address 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  load-interval 30

  !

  IP local pool ippool 192.168.4.100 192.168.4.200

  no ip classless

  IP route 0.0.0.0 0.0.0.0 62.43.195.100

  !

  IP http server

  local IP http authentication

  no ip http secure server

  IP http timeout policy inactive 600 life 86400 request 10000

  overload of IP nat inside source list 102 interface FastEthernet0/0

  access-list 102 permit ip 192.168.4.0 0.0.0.255 any

  !

  Line con 0

  line to 0

  line vty 0 4

  privilege level 15

  transport telnet entry

  line vty 5 15

  privilege level 15

  transport telnet entry

  !

  When I connect to the public IP address of the router, that everything is fine and status is connected. But I do not have connectivity to the internet and I can only ping 192.168.4.1, but no other IP address of this beach.

  I would be grateful any sort of kelp.

  Thank you

  You must make sure that your internal traffic goes to the VPN client is NOT be NATT would be.

  You need to re - write acl 102 to something like: -.

  access-list 102 deny ip 192.168.4.0 0.0.0.255 192.168.4.0 0.0.0.255

  access-list 102 permit ip 192.168.4.0 0.0.0.255 any

  HTH >

• Need help with native VPN client for Mac to the Configuration of the VPN router RV082

  Guys,

  I am trying to set up router RV082 VPN Client with native Mac for my remote access. However, no matter what I did, I'm not able to make works. Can any give me an example of how to set my router RV082 and Mac Book Pro (Mountain Lion)?

  Thank you

  Hi Jixian, the native client MAC does not work. The IPSEC VPN client is the same as the 5.x Cisco VPN client is not supported on this device.

  Your alternatives are to use PPTP or a 3rd party IPsec client such as ipsecuritas.

  -Tom
  Please evaluate the useful messages

• Cisco VPN Client for Windows 7 and WWAN devices

  Hello

  Does anyone know when Cisco will release a VPN Client for Windows 7 update that supports devices WWAN using NDIS 6.2?

  Thank you

  Dave,

  End of the client VPN of life was announced. In my view, it is safe to say that no new features will be introduced.

  AnyConnect is the way to go (Alternatively Windows 7's native IKEv2 connection works in IOS).

  Marcin

• Global VPN Client for Apple

  I've recently deployed a SonicWALL NSA2600 and have implemented a VPN site-to site both group WAN VPN that work properly. I distributed global vpn client for users who need access to network resources. However, a user uses exclusively based Apple operating systems. Y at - it a customer vpn global for Apple, or is the app of choice? If there is no other choice, this mobile app will work for a desktop Apple computer?

  Thank you

  Jason

  This link is more accurate for MacOS.

  Installation and use NetExtender on MacOS:

  

• 1811 and VPN Client

  I'm trying to connect to my router Cisco VPN Client 4.8 of Pentecost Cisco1811 Pentecost rsa - sig (certificate). On the Cisco VPN Client I resive username request I spend. When I insert them on the 1811 I resive this message on the console

  % CRYPTO-6-VPN_TUNNEL_STATUS: Group: does not exist

  My ios config is:

  AAA new-model

  !

  !

  local VPNUSER AAA authentication login

  local AAA VPNUSER authorization network

  !

  AAA - the id of the joint session

  !

  resources policy

  !

  !

  !

  IP cef

  No dhcp use connected vrf ip

  DHCP excluded-address IP 192.168.10.1

  !

  SDM-IP dhcp pool pool

  import all

  network 192.168.10.0 255.255.255.0

  default router 192.168.10.1

  Rental 2 0

  !

  !

  no ip domain search

  "yourdomain.com" of the IP domain name

  !

  ! Crypto pki token by default user pins *.

  Crypto pki token removal timeout 30 default

  !

  Crypto pki trustpoint TP-self-signed-2095781077

  enrollment selfsigned

  name of the object cn = IOS - Self - signed - certificate - 2095781077

  revocation checking no

  rsakeypair TP-self-signed-2095781077

  !

  Crypto pki trustpoint CA_Server

  Terminal registration

  Serial number no

  full domain name no

  IP address no

  password

  name of the object O = 5100, OU = customs, CN = ROUTER1

  revocation checking no

  rsakeypair SDM-RSAKey-1180596453000

  !

  !

  TP-self-signed-2095781077 crypto pki certificate chain

  string CA_Server crypto pki certificates

  !

  crypto ISAKMP policy 10

  BA 3des

  Group 2

  ISAKMP crypto identity dn

  !

  ISAKMP crypto client configuration group guest_group

  DNS 10.1.1.3

  pool vpnpool

  !

  !

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  !

  Crypto-map dynamic dynmap 10

  game of transformation-ESP-3DES-MD5

  !

  !

  list of authentication of card crypto client vpn_map VPNUSER

  card crypto vpn_map VPNUSER isakmp authorization list

  client configuration address card crypto vpn_map throw

  client configuration address card crypto vpn_map answer

  vpn_map 10 card crypto ipsec-isakmp dynamic dynmap

  !

  What can I do

  What is the OU on the certificate you have for the customer?

  What is guest_group or something else?

  Thank you

  Gilbert

• What VPN Client for ASA 5550 AnyConnect Premium connection?

  We have version9 a couple of ASA550 I want to put in place a VPN client for use with remote access to administration.  We have included AnyConnect VPN, Premium license peers 2 so I guess we can just use of Cisco AnyConnect VPN client.  I went to Cisco's Web site and it says that I don't have right to the last Anyconnect VPN Client 4.x but I don't have access to the version 3.x.

  The 3.x client is compatible with the ASA and also Windows 10?

  If Yes, what is the correct file to use, there are many files listed for download in AnyConnect 3.x?

  In addition, what is the difference between the AnyConnect 3.x and 4.x customer and why Cisco restricting 4.x?

  Jim

  AnyConnect 4.x has changed the licensing model. AnyConnect 4.x licenses are term based licensing vs perpetual 3.x. There are a number of other differences, mainly due to there being only two license types - more and Apex - no Mobile plus, Advanced Endpoint Assessment, shared VPN etc. Cisco offers a nominal or no license cost of migration until the end of 2015. (depending on what you have: positive Essentials or Apex at premium)

  AnyConnect 3.1 will work with Windows 10 and the latest version of the Software ASA (since Version 3.1.10010). Reference:

  http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...

  There are two ways it is distributed - as a stand-alone installation or package for the distribution of the ASA station. Both come in Windows, Mac OS X and Linux distributions. For a Windows client, you must use either:

  AnyConnect-Win-3.1.12020-pre-deploy-K9.ISO

  AnyConnect-victory - 3.1.12020 - k9.pkg

  .. .to the current version of these respective form factors.

• Is there a 64-bit version of the VPN Client for the coming of Vista?

  Is there a 64-bit version of the VPN Client for Vista to come for VPN 3000 series concentrators?

  Hello

  A bit is a tour here.

  According to Cisco:

  Install the VPN Client on a Vista 64 bit Machine will cause an error 1721

  Cisco IPSec Client does not support 64-bit. If the user requires a 64-bit support, upgrade path is to use the Cisco AnyConnect VPN Client instead, that supports 64-bit. Note that the AnyConnect Client supports only SSL VPN (CSCsi26069) connections.

  So if you want to go with 64-bit, you need SSL support on the VPN 3000 series and replace all IPSEC with SSL connections.

  Please rate if this helped.

  Kind regards

  Daniel

• 1710 VPN and VPN Client - routing problem '' maybe. ''

  Hello

  I was able to get with 3DES and CISCO VPN Client 3.6.1 1710. with permission of local aaa.

  When I am connected to the VPN I can ping to the IP address of the VPN router

  (24.x.x.x.) and I can ping to the router's internal interface (192.168.x.x).

  The problem is that I can't ping anything else - for example: hosts in the enterprise network (192.168.x.x).

  Configuration:

  The router's internal IP address: 192.168.x.x

  The router's external IP address: 24.x.x.x

  ippool for customers: 10.10.10.x

  The IP address of the Client after the connection is correct: 10.0.0.x (from pool)

  Maybe I'm missing something in 1710 confg? I have NAT interface internal? The default gateway of the net is FreeBSD, not the router of 1710 system.

  All ideas are welcome.

  Miro Pendev

  TI Administrstor

  Quite often, you will lose the first ping because an ARP must be sent and responded to, but if you get the subsequent pings, then it's OK.

  For what is able to browse the Internet while the tunnel is up, you must enable split tunneling. Add the following:

  > access-list 110 permit ip 192.168.1.0 0.0.0.255 192.168.1.0 0.0.0.255

  > isakmp crypto client configuration group my_usergroup

  > acl 110

  This means that the client will only encrypt the traffic to the 192.168.1.0 network, all other traffic shuts down in the clear on the Internet.

• Router vpn site to site PIX and vpn client

  I have two on one interface on the pix vpn connections that terminate VPN. client vpn and VPN site-to-site have passed phase one and two and decrypt and encrypt the packets. However as in another post I can not ping through the l2l vpn. I checked this isn't a nat problem a nd two NAT 0 on the pix and the NAT on the router access lists work correctly.

  ISAKMP crypto RTR #show its
  IPv4 Crypto ISAKMP Security Association
  status of DST CBC State conn-id slot
  66.x.x.x 89.x.x.x QM_IDLE 2001 0 ACTIVE

  IPv6 Crypto ISAKMP Security Association

  local ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (192.168.10.0/255.255.255.0/0/0)
  current_peer 66.x.x.x port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: 23583, #pkts encrypt: 23583 #pkts digest: 23583
  #pkts decaps: 18236, #pkts decrypt: 18236, #pkts check: 18236
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  #send 40, #recv errors 0

  local crypto endpt. : 89.x.x.x, remote Start crypto. : 66.x.x.x
  Path mtu 1380, ip mtu 1380, ip mtu BID Dialer0
  current outbound SPI: 0xC4BAC5E (206285918)

  SAS of the esp on arrival:
  SPI: 0xD7848FB (225986811)
  transform: aes - esp esp-sha-hmac.
  running parameters = {Tunnel}
  Conn ID: 3, flow_id: Motorola SEC 1.0:3, card crypto: PIX_MAP
  calendar of his: service life remaining (k/s) key: (4573083/78319)
  Size IV: 16 bytes
  support for replay detection: Y
  Status: ACTIVE

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:
  SPI: 0xC4BAC5E (206285918)
  transform: aes - esp esp-sha-hmac.
  running parameters = {Tunnel}
  Conn ID: 4, flow_id: Motorola SEC 1.0:4, card crypto: PIX_MAP
  calendar of his: service life remaining (k/s) key: (4572001/78319)
  Size IV: 16 bytes
  support for replay detection: Y
  Status: ACTIVE

  outgoing ah sas:

  outgoing CFP sas:

  Expand the IP NAT access list
  10 deny ip 192.168.2.0 0.0.0.255 192.168.10.0 0.0.0.255 (21396 matches)
  20 permit ip 192.168.2.0 0.0.0.255 everything (362 matches)
  Expand the IP VPN_ACCESS access list
  10 permit ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255 (39724 matches)

  I looked on the internet and that it points to a routing error when packets are being encrypted and decrypted, but you can't do a ping on the binding. However when I test the connection I did not enter any of the static routes that networks are connected directly on each side of the pix and the router. any help would be a preciated as I think there's maybe something is blocking the ping to reach the internal network at the end of pix with a configured access list.

  is ping failure of the only thing between the site to site VPN? and assuming that all other traffic works fine since it decrypts and encrypts the packets.

  If it's just ping, then activate pls what follows on the PIX:

  If it is version 6.3 and below: fixup protocol icmp

  If it is version 7.0 and higher: select "inspect icmp" under your political map of the world.

  Config complete hand and on the other could help determine if it's a configuration problem or another problem.

• ASA VPN server and vpn client router 871

  Hi all

  I have ASA 5510 as simple VPN server and 871 router as simple VPN client. I want to have the user ID and permanent password on 871 and not to re - enter username and password since 871 uses dynamic IP address and every time I have to ' cry ipsec client ezvpn xauth "and type user name and password.

  any suggestions would be much appreciated.

  Thank you

  Alex

  Do "crypto ipsec client ezvpn show ' on 871, does say:

  ...

  Save password: refused

  ...

  ezVPN server dictates the client if it can automatically connect with saved password.

  Set "enable password storage" under the group policy on the ASA.

  Kind regards

  Roman

• ASA easy vpn server and ios client both need public ip

  Hello

  If someone can define that cisco asa 5525-x and cisco 2800 router ios can be customer both parties have public ip or only side server.

  Please clear my doubt

  Hello

  Then you can do with ezvpn himself. Take the below mentioned thing for example and configure accordingly for your scenario.

  http://www.Cisco.com/c/en/us/products/collateral/iOS-NX-OS-software/iOS-...

  Concerning

  Knockaert

• 6500 IOS router Cisco VPN Client using DHCP no Pool of IP

  Hey guys,.

  I have a little trouble trying to get my vpn client to use a dhcp server rather than the pool of intellectual property.  When I use the command IP pool everything works fine, but when I use the dhcp command I get an error on the client-side saying that no address private IP was affected by the peer.

  Here is my config.

  connection of AAA VPNCLIENT_AUTHEN group local RADIUS authentication

  local VPNCLIENT_AUTHOR AAA authorization network

  Configuration group customer isakmp crypto VPNCLIENT_GROUP

  xxxxxxxxxxxxxxxxxxxxxxxxxx key

  DNS 172.25.128.43 172.25.65.43

  win 172.25.1.54

  sktnhr.ca field

  172.25.0.27 DHCP server

  GIADDR DHCP 172.25.205.1

  DHCP timeout 10

  pool # VPNCLIENT_IPPOOL

  Crypto isakmp ISAKMP_PROFILE profile

  VRF HUB_VRF

  match of group identity VPNCLIENT_GROUP

  list of authentication of client VPNCLIENT_AUTHEN

  VPNCLIENT_AUTHOR of ISAKMP authorization list.

  client configuration address respond

  crypto dynamic-map DYN_MAP 1020

  game of transformation-ESP-AES-256-SHA

  ISAKMP_PROFILE Set isakmp-profile

  market arriere-route

  card crypto HUB_CRYPTO_MAP 6005-isakmp dynamic ipsec DYN_MAP

  local IP VPNCLIENT_IPPOOL 172.25.205.25 pool 172.25.205.250

  I can see the dhcp request and offer on my dhcp server but nothing is for the customer.  When I use a pool I ping the dhcp server, which makes me think the roads are okay.  Anyone has any ideas.

  You need the giaddr in an EasyVPN server configuration.  Try adding looping to your switch and test it again.  If you use an iVRF, make sure that the closure is in the VRF and the interface to the server.

• IPP with Ezvpn and VPN Clients

  Hello

  I have a 5585 ASA running on 8.4. I have it set to accept the ezvpn NEM mode clients and then push the routes through IPP in the OSPF via redistribution on a list sheet road. Now I came with a second condition of the addition of VPN Clients to the same firewall. In the current configuration if I activate customers, they will push the 32 routing updates in the routing table makes a table long enough and I don't want to do that. What I understand of the redistribution of static route is that:

  (1) road should be static in the routing of ASA, inserted through IPP table or manually added

  (2) my redistribution list will allow all the roads that fall within the specific subnet.

  If I have a 192.168.1.0/24 defined in the ACL of redistribution, a route in this 24 will be added to the routing table. Please refer to the sample configuration:

  http://www.Cisco.com/en/us/partner/products/ps6120/products_configuration_example09186a00809d07de.shtml

  In the example of config is the road added to the list redisttribution/24 network but if you examine the output at the end of the document, a 32 road has been inserted in the router's routing table.

  I want to keep Ezvpn with IPP clients and at the same time to have VPN Clients running without IPP. Would appreciate any help in this!

  Thank you

  Sylvana

  Route-synthesis is only possible if for OSPF routers ABR/ASBR. I wasn't talking another ospf process, but on another area ospf.

  if I add summary-address for only my client vpn pool (10.10.0.0/16) will  my other routes for ezvpn stop being advertised or will they continue  to be advertised as before and only VPN Pool would be summarized?
  

  If you select the summary for 10.10.0.0/16 only that the network will be sumarized. Why would another announcement due to the synthesis of 10.10.0.0/16 cease?

• Configure the 2 network cards in a VM for MPLS LAN and the other for internet

  Dear all,

  I have a HP Server with 2 NIC cards. ESXI 4.0 is installed and 3 VM was created in it. Initially that a NIC card was connected to the path of the LAN MPLS switch and another card NETWORK was not connected to the internet switch port.

  Each VM only had a single NIC in it. So I assigned MPLS IP LAN to ESXI host and VM 3 and everything worked perfectly.

  Now, I wanted to have the internet connection for my 3 VM. So I plugged the 2nd NETWORK card with internet port and added the second NETWORK card to the ESXi using the Vsphere client - & gt; configuration - & gt; Networking option. Now the two nic cards are ponting to the network of the virtual computer.

  I've added 2 network card to all 3 VM and assigned to the internet IP addresses to all of these NICs. order of MPLS and internet work at the same time, I removed the card NIC MPLS entry door and manually routed through route add command. After this MPLS and internet worked well in 1 VM.

  I tried the same thing in 2nd and 3rd VM but it failed. whenever I have add 2nd network card in the virtual machine, the first of this virtual machine network adapter does not work.

  I'm after the right approach? Help, please...

  Kind regards

  Ashok doriane

  If I understand correctly your installation, you connected the physical NIC to two different IP networks.  Then you connected these cards in the same switch-v on the server.

  This essentially fills two different networks at the layer level 2 layer 3.

  You want rather than the two networks remain separated inside the host.

  • create a new v-switch on the host

  • move the internet NIC v-switch

  • Move the second NIC on each virtual machine to this switch

  • Make sure that access to internet VM NIC is one with a default gateway on a virtual machine OS

  • remove the default gateway of the NIC MPLS

  • creating persistent static routes to the NIC MPLS for any affected networks it beyond the same subnet as the NIC itself.  Addresses on the same subnet will be automatically accessible. Just roads for those outside this range.

  Steve Puluka

  JNCIA-ER enterprise routing

  Enterprise JNCIA-EX switching

  Senior network administrator

  Liberty Dialysis

  http://puluka.com/home