Configuration of SNMP on Cisco Small Business 300 Series managed switch
Please can someone help me configure SNMP on Cisco Small Business 300 series switch?
Thank you
Hi Anton,.
Don't forget to activate the service SNMP is first of all: Security > Services TCP/UDP.
http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=3b13278d9ef9402a8fef57...
also, you will find useful documents for configuration etc on our server community kb:
http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=183cae2148d445b2a07473...
Let us know if you have any problems.
Aleksandra
Tags: Cisco Support
Similar Questions
-
Plug-and-Play for Cisco Small Business 300 Series managed switch
Nice day
What are the automatic installation options available for the Managed Switch series of Cisco Small Business 300?
It seems there are not, the operating system is not the standard IOS I used to.
I would use with ability to bridge the Infrastructure first Cisco PnP.
Concerning
Stone
First Infrastructure use and assume an agent CNS (Cisco Network Services) on the other side, when you enable the 'plug & play '. Series 300/500 do not run IOS and does not include the CNS agent, but there is a way to activate the automatic configuration. Switches supported by the automatic DHCP configuration (using DHCP options 66, 67, etc.) in which case they automatically download their config to a TFTP server at boot time. This allows an administrator to put the configs for all switches on a TFTP server and simply start a default switch factory in order to obtain config.
Seal a document shows how this is done.
Hope that the information would be useful.
-
Accounting on a Cisco Small Business SF300-08
Hello
"Cisco Small Business 300 Series managed switches Administration Guide" and the sheet indicate that this switch can make requests of accounting with a Radius server. On the switch interface/CLI SF300, there is that the authentication port, the port of account cannot be resolved (and nothing is sent by the switch to the default port). I guess that the SF300-08 doesn't manage accounting. Maybe I need to change to another model. Could you give me another model in the same price range?
Thank you
Laurent.
Hi Laurent, I am pleased that the 1.2.5.70 has solved this problem.
Please keep Advisory of the 1.2.5.70 firmware has also been lifted for now.
Please note that we have identified a potential problem with the 1.2.5.70 update for the series 200, 300 and 500 switches. As a precaution, we took down the 1.2.5.70 free while we determine the cause of the issue, the seriousness and the scope. We re - ask the release or publish an updated based on the results of our analysis.
-
Router Cisco Small business with the functionality of the link aggregation
Hi all!
can someone tell me if there is a router from Cisco Small business with the functionality of the link aggregation? (I want to connect two 4 Mbps SDSL for flow) The RV082 can do?
Best regards
You would need a RV016, who takes in charge up to 7 WAN ports. RV082 has only two WAN ports.
-
My small business SF 302-08 Switch will not let me apply the command "Routing".
Hi everyone, my switch cisco small business SF 302-08 has the latest firmware and I want to activate the command routing, but it doesn't let me do that.
I've read the reference guide for orders, do all this procedure: IP Routing Protocol independent commands starting at page 629, but nothing happens. I need this because I want a routing between VLANs
Kind regards.
Hi Felipe
Look forward to hearing how you go.
If you reset the factory default switch and the switch is NOT connected to a server, the switch restarts with a default IP 192.168.1.245 address according to the Quick start guide . If your PC has a static address 192.168.1.2, you should be able to access the graphical interface of the switch.
http://www.Cisco.com/en/us/docs/switches/LAN/CSBMs/sf30x_sg30x/Quick_Start/78-19252-01.PDF
If the switch is connected to a DHCP server, the switch Gets an IP via DHCP.
I've had problems using hyperterminal on my Windows 7 box, that I have overcome by restarting my PC in order to free the COM port. Settings of the console are;
- 115200 bits per second
- 8 data bits
- no parity
- 1 stop bit
- no flow control
If you really have problems, and you think that the switch is faulty, you have the possibility to use the services of small business Support Center (HWC) in order to identify if the switch is good or bad.
The URL that watch phone numbers are lower;
Best regards, Dave
-
Cisco Small Business Equipment VLAN security issue
Hi, I have a RV220W router and a switch SG200-18. I'm trying to set up my network to be as secure as possible...
The RV220W has the configuration of VLAN next:
Port 1: Manage, DMZ, Business, Test, Diag, home and anywhere (not identified)
Port 2-4: not used (unidentified) and people with DISABILITIES
All ports were excluded from the default VLAN
SG200-18 has the configuration of VLAN next:
Port 1 (trunk): manage, DMZ, Business, Test, Diag, home and anywhere (not identified)
Port 2-17 (access): not used (unidentified) and people with DISABILITIES
Port 18 (access): manage (unlabeled) * used to configure and manage the switching and routing of a pc
All ports were excluded from the default VLAN
I installed this according to the instructions in the Cisco security best practices: http://www.cisco.com/warp/public/cc/pd/si/casi/ca6000/prodlit/vlnwp_wp.pdf
My questions regarding my network of quenching of Double-Encapsulated 802. 1 q / attack of VLAN nested. The white paper suggests to disable the VLAN native/unidentified all trunk ports... Unfortunately the RV220W seems to require a VLAN without label on each port (won't allow me to only have the tag VLAN)... Can someone suggest a more secure configuration given that I work with?
Thank you!
P.S. the switch allows me to configure a port mode 'General' where I can configure the frame Type to "Admit tag only" to allow only traffic labeled... I don't know if this would increase security?
In what concerns the vlan tag/UNTAG Yes. You must take into account the limitation of the router.
-Tom
Please mark replied messages useful -
DHCP SNOOPING TO THE SWITCH OF CISCO SMALL BUSINESS SF200-48
Please help me. I need to know if the dhcp snooping is available in cisco firmware version 1.3.7.18.
Hi Bonnie, as I know DHCP snooping is not on the SX200 switch. I am also unable to find documentation in Administrator's guide and release notes not stating that it is.
-
Remote Desktop and Cisco Small Business RV042
With our old router Linksys Wireless on the issue of applications we can redirect the port, for example:
Remote desktop access from external pc: 201.85.X.X:1234 (to appoint our public IP and port 1234)
Whit this we can access the private 10.1.X.X in Lan services Terminal Server machine WinVista Pro.
I want to forward external port 1234 > 3389 Lan. Is it possible with RV042?
Note: Firmware Version: v4.1.1.01 (latest)
To change the ports source and destination, you must use the UPnP function
That's what I use on the RV0XX
best chance
-
Configuration of Digital Signature of small business
We have about 125 employees who have digital signatures created using Acrobat 9 and X. is it possible to import all certificates of employee (public keys) at the same time in Acrobat so we can validate signatures when the signed PDF is opened?
You can import all certificates on an installation of Acrobat, the value of the trust and then use export security settings in Acrobat to export all these approved identities. Then you send the acrobatsecuritysettings file to each employee and need to import the security settings for this file.
-
Cisco TelePresence Manager version 1.7 does support Windows Small Business Server 2008?
Hello
Is Microsoft Windows Small Business Server 2008 supported the Protocol LDAP, AD and MS Exchange server for Cisco TelePresence Manager version 1.7?
Thank you
AA
Hello Ahmed - although this configuration "can work", Windows 2008 Small Business Server is not on the support list. This means that it has not been tested and it certifies to work with telepresence.
To my knowledge, he's not on the roadmap for the future support however, I search and repost as soon as I have an answer for you.
Kind regards
-Andrew
Sent by Cisco Support technique iPhone App
-
What small business routers support DHCPipv6-DP?
I have a rv042-g, which apparently does not support the DP. DP is necessary for subnets to connect your local LAN ipv6 addresses to the Internet.
(If there is a manual way to implement, I have not found it).
I intend to return or sell the rv042-g once I found a better router.
Looking through this thread suggests that it is supported on rv042 but not the rv180
https://supportforums.Cisco.com/discussion/11629126/does-rv180w-support-...
SMB team may be able to tell which specific version of fw its on
http://www.Cisco.com/c/en/us/support/Web/TSD-Cisco-small-business-suppor...
-
Small Business Investment program Question
I have a question about the small business investment program. I just bought a Cisco Small Business router and additional Small Business 8 Port Switch. Later on the road, we might need a 16, Port or more, but we don't need to exchange any now. We wonder what it takes just to enroll in the program. What is the link you need to register?
http://ciscoinvestmentprotection.com/register.html
Thank you!
Hi Nathan,
I just noticed that you also tweeted on the subject. Anyway, here's the URL that you should go and look for information about this program:
http://ciscoinvestmentprotection.com/brochure.html#
Kind regards
Cindy Toy
Cisco Small Business Community Manager
for Cisco Small Business products
-
Pix 501 for Small Business SERVER 2003 configuration problems
I am new to cisco equipment. My company recently purchased a firewall of Pix 501 unlimited number of users, it is connected to an internet connection by cable with a dynamic ip address. Internet works fine and so the dhcp server.
I have a Windows 2003 Small Business Server on our network. I need to configure the firewall to forward ports on the SBS server for remote web workplace.
Also about a week ago I lost connectivity to the GUI of PDM via my web browser. Telnet and console work perfectly well.
I enclose my config file.
Any help will be appreciated. Thank you
Ed
FIRT off, you do not have a group-access instruction set for one of your ACL. This means that you have blocked all inbound traffic. You also have your incorrect static instructions. You can start by cleaning your config and enter the correct commands, you should be able to stick to your firewall config mode:
No list will host 192.168.1.1 acl-enabled access 192.168.1.1
no access list acl_outside not allowed tcp any any eq www
no access list acl_inside not allowed tcp any any eq www
no access list no incoming icmp permitted any one
No list of permitted no inbound tcp access any host 24.50.241.113 eq https
No list to access acl - permit gre 192.168.1.1 host 192.168.1.1
No outside_in not allowed access list tcp any host 24.50.241.113 eq www
not static (inside, outside) tcp interface www SBSServer www netmask 255.255.255.255 0 0
not static (inside, outside) tcp interface https SBSServer https netmask 255.255.255.255 0 0
not static tcp (exterior, Interior) interface www SBSServer www netmask 255.255.255.255 0 0
not static tcp (exterior, Interior) interface https SBSServer https netmask 255.255.255.255 0 0
static (inside, outside) tcp 24.50.241.113 80 192.168.1.69 80 netmask 255.255.255.255 0 0
static (inside, outside) 24.50.241.113 tcp 443 192.168.1.69 443 netmask 255.255.255.255 0 0
access-list OUT-IN permit tcp any host 24.50.241.113 eq https
access-list OUT-IN permit tcp any host 24.50.241.113 eq www
allow to Access-list OUT-IN a whole icmp
Access-group OUT-IN in interface outside
What ip you are trying to access your pdm of? the looks of configuration http correct, unless your coming to one other than 192.168.1.x ip address
Let me know if it works
-
best configuration for Small Business Server
I'm looking for advice on HW and SW recommendations for a small business. We have 15 users, 20 computers and 3 printers. I currently have a single Windows Server 2008. I want to run a domain controller main for all users, file sharing, print server, possibly Windows Update Center and eventually MS Exchange. I am trying to decide the best configuration of HW with a fairly cheap budget. I currently have 1 I7 based server with 4 GB of Ram, several IBM servers, P4 306 m (I have 4 +), and a lot of hard drives (all in a half rack). I also need a decent backup system.
Can anyone recommend the best configuration of HW player and hard? Should I analyze server roles? With respect to the SW, I'm a non-profit and use Windows Server 2008 (at a discount)
Thank you
Hello
The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.
http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer
It will be useful.
Let us know if you encounter problems with Windows in the future. We will be happy to help you.
-
ICW fails to configure the firewall on Small Business Server 2003 R2
Can anyone help please when I run the wizard of internet connection on a Small Business server 2003 R2, it fails on the firewall configuration, when I check the log I get the errors below. He was going well until my network card for my internet connection has failed and I replaced and set up another card I made sure, there is nothing in Device Manager, even in hidden for the old devices map
C:\Program Files\Microsoft Windows Small Business Server\Networking\ICW\wizrfire.dll, version 5.2.2893.0
call CRFireCommit::ValidatePropertyBag (0x1de5fa8).
UPnP URL is http://192.168.1.1:5000 / rootDesc.xml
The call for initialization of device Upnp () returned ok.
Error 0 x 1 returned by the call to HttpGetDeviceXML().
Error 0 x 80004005 returned by the call to GetServiceConfigURL for WANPPPConnection().
Call the GetServiceConfigURL for WANIPConnection () returned ok.
Router supports WANIPConnection
Service config URL ctl / http://192.168.1.1:5000 / IPConn
Error 0 x 1 returned the call to CRFireCommit::ValidatePropertyBag no RRAS NAT Interface Public, the Basic Firewall is not configured. ()The call for initialization of device Upnp () returned ok.
Error 0 x 1 returned by the call to HttpGetDeviceXML().
Error 0 x 80004005 returned by the call to GetServiceConfigURL for WANPPPConnection().Hello
Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please ask your question in the Forum of the Small Business Server. You can follow the link to your question:
http://social.technet.Microsoft.com/forums/en/smallbusinessserver/threads
Maybe you are looking for
-
Satellite C660 keyboard and mouse not working not
I have a Satellite C660 who is about to leave the window. The list of problems are the following: Keyboard does not workMouse pads and button do not workUSB mouse and keyboard do not work (but light up with power)He likes also turn off randomly when
-
Satellite L300-1AR - Media test failure error on startup
Hello I have a problem on my series of Toshiba L300 - 1AR. It prevents me from going further, he shows me exactly: "Intel UNDI, PXE - 2.1 (build 082)Copyright (C) 1997-2000 Intel Corporation For Realtek RTL8101E/8102E PCI - E Ethernet Controller v.1.
-
I use windows 8 (excerpt from developres of windows). I am not as much with the graphics drivers for my dell inspiron 1520 please tell me if I will be provided later or should I reintall windows7 in my system.
-
Problem with sound when Aspire 5750 G connected via HDMI
Hello I'm having a problem connecting my Aspire 5750 G to my TV through my HDMI cable. Previously, I've always been able to go in manage Audio devices to choose the HDMI option, but today this option disappeared. Nothing has changed with my TV or my
-
BlackBerry, Blackberry Z10 Z10 - Device Software Update bberror-bb10-0015
My intentions were to complete a security wipe and re - install the latest OS. I now have bberror-bb10-0015 (I think that's what it's called). When I go to the site to get the latest update, it seems error down on downloading at 98%. I continue to