Redirect port on the router Cisco 881 can following the active WAN Interface
Hello
Is there a way to make the port Fowarding after the Active Wan Interface?
In this case the port Fowarding only works when the interface is active is GigabitEthernet0/0
Bureau3616 (config) # ip nat inside source tcp static 192.168.2.xxx 3389 interface GigabitEthernet0/0 3387
If our ISP-1 failure on WAN-1 Interface GigabitEthernet0/0 switch to internet access automatically to ISP - 2 WAN-2 on GigabitEthernet0/1 but the port forwarding does not work because it is fixed to the other interface only and I is not the way to port forwarding follow the WAN an actress.
Let me know please if anyone has an idea.
It is a part of my config
! NAT configuration
Bureau3616 (config) # ip nat inside source map route NAT-WAN1 interface GigabitEthernet0/0 overload
Bureau3616 (config) # ip nat inside source map route NAT-WAN2 interface GigabitEthernet0/1 overload
Bureau3616 (config) # NAT-WAN1 allowed 10 route map
Ip address of Bureau3616 (config-route-map) # match 100
Bureau3616 (config-route-map) # match interface GigabitEthernet0/0
Bureau3616 (config-route-map) #exit
Bureau3616 (config) # NAT-WAN2 allowed 10 route map
Ip address of Bureau3616 (config-route-map) # match 100
Bureau3616 (config-route-map) # match interface GigabitEthernet0/1
Bureau3616 (config-route-map) #exit
! Port Fowarding configuration
Bureau3616 (config) #ip avant-protocole nd
Bureau3616 (config) # ip nat inside source tcp static 192.168.2.xxx 3389 interface GigabitEthernet0/1 3387
Thank you!
You can, but you can't use transfer based on the interface of the to do. It should be based on the address itself. It's fine if you have static addresses or reserved on your WAN interfaces, but pose a problem if the addresses are dynamic:
ip nat inside source static tcp 192.168.2.x 3389 1.1.1.1 3389 route-map NAT-WAN1ip nat inside source static tcp 192.168.2.x 3389 2.2.2.2 3389 route-map NAT-WAN2Replace the address of your interface WAN1 and 2.2.2.2 with the address of your 1.1.1.1 WAN2 interface. Applying the road maps will work pretty much the same way as it does with your statements of overload. Each transmission NAT rule applies only to the traffic corresponding to rules of the road map.
Tags: Cisco Network
Similar Questions
-
How to recover the active user interface objects on a screen?
Hello
Is it possible to recover all of the active user interface objects on a screen?
I found ago api like net.rim.device.api.ui.Screen.getFieldWithFocus, but how to get sound type of subclass as ButtonField or BitmapField?
another take:
If you retrieve the field with focus, you can check what type of field you have recovered (using instanceof, for example)
-
is it possible to add a functional command line to the Active Desktop interface
Name of the operating system: Microsoft Windows XP Professional
OS version: 5.1.2600 Service Pack 3 Build 2600you are not sure if it did as a function of available any OS, but is it possible to get a command line as a windows active desktop?
Hi Joshua,.
There is no this command line to enable the Active Desktop. You may need to as mentioned in the following article.
-
Cisco 881 can ping internet but computers behind the router cannot
I have a cisco 881, which can ping internet but not of any computer behind it. Computers receive a static IP address, that is why there is no DHCP assigned to any LAN interface. Here's the running configuration:
Building configuration...
Current configuration: 6435 bytes
!
! Last modification of the configuration at 22:15:30 UTC Friday, March 11, 2016
!
version 15.5
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
router host name
!
boot-start-marker
boot-end-marker
!
!
logging buffered 51200 warnings
!
No aaa new-model
BSD-client server url https://cloudsso.cisco.com/as/token.oauth2
iomem 10 memory size
!
Crypto pki trustpoint TP-self-signed-76299383
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 76299383
revocation checking no
rsakeypair TP-self-signed-76299383
!
!
TP-self-signed-76299383 crypto pki certificate chain
certificate self-signed 01
30820227 30820190 A0030201 02020101 300 D 0609 2A 864886 F70D0101 05050030
2F312D30 2B 060355 04031324 494F532D 66 2 536967 6E65642D 43657274 53656C
69666963 37363239 39333833 31333031 33313231 30333034 301E170D 6174652D
5A170D32 30303130 31303030 3030305A 302F312D 302B 0603 55040313 24494F53
2D53656C D 662 5369 676E6564 2D 436572 74696669 63617465 2 373632 39393338
3330819F 300 D 0609 2A 864886 F70D0101 01050003 818 0030 81890281 8100B39C
1F1F1B5A 620D3DB7 E4B82486 D8A6E928 E880F817 20D8D5D8 744 HAS 6985 B48A0AEF
072919 6ABF6428 C 9 272B2F4E 28382554 1D1CC5CD 701F9646 38EEE5CE 67F475C4
DD5B464B ECBD78AF A5B6B36B D2791CFE E6CB886F B030E179 7A209BC4 1CDC6BA1
711616 C 4FD6BE16 4 489DCC5F A5EE9729 365858FD 1654EA5F 3B7F90B2 19470203
010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 551 D 2304 0F060355
18301680 1465D9D2 8C6F18DF 98EF832A 03DE7ADD 97301 06 03551D0E D45A6C59
04160414 65D9D28C 6F18DF98 EF832A03 DE7ADDD4 5A6C5997 300 D 0609 2A 864886
818100A 6 05050003 928BFD76 AEE144B3 540415EE 7DC2339D B6142CF6 F70D0101
60E3A6DF 06DA321C B711183C 80755902 2D1D9407 857F05ED B987C08D 25002B5F
F3C0F996 8CDA1830 3F85456B 6C6F2A4B 774B93DC 256AB90E 5A46126C C2D044DB
3B76F1A2 0E98D2F0 A0D656CF 5031C7D7 1D9D2F88 188927 4 EEAA3915 E97C7B83
ECF7239B 5B7F0FDD E4C9CA
quit smoking
!
!
!
!
!
!
!
!!
DHCP excluded-address IP 192.168.136.22 192.168.136.30
DHCP excluded-address IP 192.168.131.22 192.168.131.254
!
IP dhcp Internet pool
network 192.168.131.0 255.255.255.0
DNS-server 70.28.245.227 184.151.118.254
router by default - 192.168.131.157
!
!
!
name of the IP-server 70.28.245.227
name of the IP-server 184.151.118.254
IP cef
No ipv6 cef
!
!
!
!
!
Authenticated MultiLink bundle-name Panel
!
!
!
!
!
!
!
!
CTS verbose logging
udi pid C881-K9 sn FGL1927224B standard license
!
!
Archives
The config log
hidekeys
username * 15 secret 5 privilege TOHi $1$ $ xwZvR0n8p6r00xE5nnBE11
!
!
!
!
!
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
isakmp encryption key * address 96.45.14.xx
!
!
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
tunnel mode
Crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac
tunnel mode
Crypto ipsec transform-set esp-SHA2-ESP-3DES-3des esp-sha-hmac
tunnel mode
Crypto ipsec transform-set esp-3des SHA3-ESP-3DES esp-sha-hmac
tunnel mode
!
!
!
map SDM_CMAP_1 1 ipsec-isakmp crypto
Description Tunnel to96.45.14.xx
the value of 96.45.14.xx peer
game of transformation-ESP-3DES-SHA2
match address 102
!
!
!
!
!
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
no ip address
!
interface FastEthernet3
switchport access vlan 2
no ip address
!
interface FastEthernet4
port WAN Description
DHCP IP address
response to IP mask
NAT outside IP
IP virtual-reassembly in
automatic duplex
automatic speed
map SDM_CMAP_1 crypto
!
interface Vlan1
Description of control network
IP 192.168.131.157 255.255.255.0
IP access-group VLAN1_In in
IP nat inside
IP virtual-reassembly in
!
local pool IP VPN 192.168.131.152 192.168.131.155
default IP gateway - 174.0.0.1
IP forward-Protocol ND
IP http server
23 class IP http access
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
IP high speed-flyers
Top 10
Sorting bytes
!
IP route 0.0.0.0 0.0.0.0 174.0.0.1 permanent
!
VLAN1_In extended IP access list
Note the incoming traffic
Note the category CCP_ACL = 1
Note the crosstalk
deny ip 192.168.135.0 0.0.0.255 192.168.130.0 0.0.1.255
deny ip 192.168.136.0 0.0.0.255 192.168.130.0 0.0.1.255
Note the crosstalk
deny ip 192.168.130.0 0.0.1.255 192.168.135.0 0.0.0.255
deny ip 192.168.130.0 0.0.1.255 192.168.136.0 0.0.0.255
allow an ip
VLAN1_Out extended IP access list
Note for diagnosis
Note the category CCP_ACL = 1
Note Diag
IP enable any any newspaper
allow_all extended IP access list
Note the category CCP_ACL = 1
IP enable any any newspaper
!
!
Note category of access list 1 = 2 CCP_ACL
access-list 1 permit 192.168.1.0 0.0.0.255
Note access-list category 2 CCP_ACL = 2
access-list 2 permit 192.168.130.0 0.0.0.255
Note access-list 100 category CCP_ACL = 4
Note access-list 100 IPSec rule
access-list 100 permit ip 192.168.131.0 0.0.0.255 192.168.125.0 0.0.0.255
Note access-list 100 IPSec rule
access-list 100 permit ip 192.168.131.0 0.0.0.255 192.168.120.0 0.0.0.255
Note access-list 101 category CCP_ACL = 4
Note access-list 101 IPSec rule
access-list 101 permit ip 192.168.131.0 0.0.0.255 192.168.125.0 0.0.0.255
Note access-list 102 CCP_ACL category = 4
Note access-list 102 IPSec rule
access-list 102 permit ip 192.168.131.128 0.0.0.31 192.168.125.0 0.0.0.255
Note access-list 103 CCP_ACL category = 4
Note access-list 103 IPSec rule
access-list 103 allow ip 192.168.131.0 0.0.0.255 192.168.125.0 0.0.0.255
!
control plan
!
!
!
MGCP behavior considered range tgcp only
MGCP comedia-role behavior no
disable the behavior MGCP comedia-check-media-src
disable the behavior of MGCP comedia-sdp-force
!
profile MGCP default
!
!
!
!
!
!
!
Line con 0
no activation of the modem
line to 0
line vty 0 4
access-class allow_all in
access-class allow_all out
privilege level 15
password *.
opening of session
transport telnet entry
telnet output transport
!
max-task-time 5000 Planner
Scheduler allocate 20000 1000
!
!
WebVPN WAN gateway
IP address 192.168.126.9 port 44443
redirect http port 80
SSL trustpoint TP-self-signed-76299383
development
!
WebVPN context PLC
WAN gateway
!
SSL authentication check all
development
!
default group policy
functions compatible svc
SVC-pool of addresses "VPN" netmask 255.255.255.224
SVC Dungeon-client-installed
generate a new key SVC new-tunnel method
SVC split include 192.168.131.0 255.255.255.224
mask-URL
by default-default group policy
!
endAny ideas?
Thank you.
I see ip nat inside and ip nat outside interfaces configured on. But I don't see any translation of address configured. This would preclude anything inside the unit to be able to access the Internet.
HTH
Rick
-
Want to update IOS through the Rommon mode in router Cisco 881
Hi all
I'm not able to upgrade IOS via mode Rommon in Cisco 881 router as FE 4 port is in router only L3 and rommon mode it supports of 0 - 3-way only.
So please confirm for me that is there any other way or Cisco 881 router will not support IOS via Rommon upgradation.
Kindly help.
Hi charrier you do not give the ip address of the router interface he gets in rommon so it should not matter what interface, as long as your pc and peripherals, same subnet to push the tftpdnld - see doc
http://www.Cisco.com/c/en/us/TD/docs/routers/access/800/software/CONFIGU...
EDIT: See this too good examples even syntax for 800
https://supportforums.Cisco.com/document/12441/tftpdnld-ROMMON-command-r...
-
Several DMVPN Instances on the same WAN Interface
Hi people,
Is it possible to run several Instances of DMVPN on one WAN Interface? We can for example configure 3 Tunnels on a router using a same Interface WAN but running Instances separated from EIGRP for each Tunnel? Kindly let me know, Alioune
Hi Martin,
Yes, you can create DMVPN as you say with a WAN interface it's possible... you can have several interfaces tunnel pointed a WAN interface as the source interface, which is located in a public area... with different public ip as destination tunnel...
Tunnel1 interface
Description * A - VPN Tunnel *.
bandwidth 100000
IP vrf forwarding Red
IP 10.0.252.2 255.255.255.252
no ip redirection
no ip unreachable
no ip proxy-arp
IP mtu 1500
load-interval 60
source of tunnel GigabitEthernet0/0 (WAN Interface)
tunnel destination 1.1.1.1
protection of ipsec profile dmvpn tunnel
!
Tunnel1 interface
Description * B - VPN Tunnel *.
bandwidth 100000
IP vrf forwarding Red
IP 10.0.252.5 255.255.255.252
no ip redirection
no ip unreachable
no ip proxy-arp
IP mtu 1500
load-interval 60
source of tunnel GigabitEthernet0/0 (WAN Interface)
tunnel destination 2.1.1.1
protection of ipsec profile dmvpn tunnel
!
like the above... example...
Please rate if the information provided is useful!
-
Missing fonts for the active user interface
I downloaded a user interface of the market of assets of the CC.
When I open it in Photoshop, it was a notice of missing fonts.
The police is Ubuntu. TypeKit has this font, but I can't download it as a font of regular funds because it is Web only.
How can I work with the examples in the user interface if Ubuntu is missing?
Hi Sandee,
If you need a font that is not available for synchronization of Typekit (or does not part of the library of Typekit at all), you can usually buy a license of the Foundry or one of their resellers.
The Ubuntu family is available as a free download on their site:
I hope this helps; Let me know if you have any other questions. Best,
-liz
-
Several external IPs on Cisco 881
Nice day
I have a Cisco 881 router on which I am putting in place some NAT to allow external connections on some IP addresses replacing my ISP to connect to some ports on my internal servers. Unfortunately, I'm not a network engineer and something seems to be non-tout to right with my setup.
My ISP, I have IP 184.183.156.98, he was assigned to the WAN port on my router Cisco 881 (FastEthernet4), and I have this working properly. Rules of Port forwarding I have in place that use this IP address work very well. In addition, I have the small block of IPs 184.183.150.161 - 164. None of the port forwarding rules put in place for these seem to work at all.
If you need the full config file, please let me know. This section below seems to be the relevant bits to my question, the entries in bold are the port forwarding rules that I think should work, but who do not seem to.
!
interface FastEthernet4
WAN description $ FW_OUTSIDE$
IP 184.183.156.98 255.255.255.252
no ip redirection
no ip unreachable
NAT outside IP
IP virtual-reassembly in
automatic duplex
automatic speed
!
overload of IP nat inside source list 23 interface FastEthernet4
IP nat inside source static tcp 192.168.10.205 1024 184.183.150.162 1024 extensible
IP nat inside source static tcp 192.168.10.205 1025 184.183.150.162 1025 extensible
IP nat inside source static tcp 192.168.10.205 1026 184.183.150.162 1026 extensible
IP nat inside source static tcp 192.168.10.205 184.183.150.162 1027 1027 extensible
IP nat inside source static tcp 192.168.10.205 3061 184.183.150.162 3061 extensible
IP nat inside source static tcp 192.168.10.205 3064 184.183.150.162 3064 extensible
IP nat inside source static tcp 192.168.10.210 888 184.183.150.163 888 extensible
IP nat inside source static tcp 192.168.10.93 1024 184.183.150.164 1024 extensible
IP nat inside source static tcp 192.168.10.93 1026 184.183.150.164 1026 extensible
IP nat inside source static tcp 192.168.10.93 184.183.150.164 1027 1027 extensible
IP nat inside source static tcp 192.168.10.93 184.183.150.164 3060 3060 extensible
IP nat inside source static tcp 192.168.10.93 6901 184.183.150.164 6901 extensible
IP nat inside source static udp 192.168.10.93 6901 184.183.150.164 6901 extensible
IP nat inside source static tcp 192.168.10.250 88 184.183.156.98 88 extensible
IP nat inside source static tcp 192.168.10.250 37777 184.183.156.98 37777 extensible
IP route 0.0.0.0 0.0.0.0 184.183.156.97
!
Note access-list 23 CCP_ACL category = 19
access-list 23 allow 192.168.10.0 0.0.0.255
access-list 23 allow 192.168.20.0 0.0.0.255
access-list 23 allow 192.168.30.0 0.0.0.255
access-list 23 permit 192.168.40.0 0.0.0.255
Note access-list 23 VPN Internet acccess
access-list 23 allow 192.168.50.0 0.0.0.255
Thank you
Adam Corbett
Adam
From what you have posted your config looks very good. Are you sure that your ISP routes these IPs to your external interface?
How do you test it?
Jon
-
Interface issues Netgear Smartswitch to the Cisco 881 LAN port
Hi, we have 100 routers Cisco 881 in our network and they work all fine for the Linksys, 3Com, switches etc. The problem we encountered is interfacing to switches from Netgear. Netgear switches use automatic detection on their ports and it doesn't seem to be compatible with auto MDIX detection on the LAN Cisco 881 4 serial ports on the router 881 hub. Someone has encountered this problem before? A cross over cable solve the problem? Since both executed MDIX autosensing they never synch - so probably a cross on would not make much. I see this with all Netgear smartswitches. If you put a small switch between the Netgear switch and router Cisco 881 everything works well except to pass traffic to port 9000. Any ideas would be appreciated.
See you soon,.
Len
Hello
There should be no problem using crossover cable. You can try disabling autoMDI/MDIX (not auto mdix) on the cisco device and keep a straight cable but if it fails, use a crossover cable.
Concerning
Alain
Remember messages useful rate.
-
Copy the configuration of Cisco 881 to Cisco 2901
We replace our router Cisco 881 with a Cisco 2901 router. If I backup the configuration of the 881 and restore it on the 2901, will there be problems? We just want our 2901 to work the same. Thank you.
routers/switches etc. can with a base image which may allow only certain features the devices come with these out of the box so that they work.
You can buy advanced ip services images or images of advanced security that will allow all the features work. For example, you cannot use BGP or ACB unless you have an advanced picture, but you can be allowed to use RIP and EIGRP stub.
You can check what is running on your 881 with a license to show what it will tell you what is on
-
Redirect Port RV042 bypassing ACL
I have a RV042 with Port Forwarding configured for RDP. This Port forwarding rule is applied before my ACL - sort of subnets that are not allowed through are allowed in. Version 4.0.0.07 firmware. Any help would be greatly appreciated.
Hi Eric, the default state table may be the problem.
Try to access rule something like -
Deny action
Service of all
The source WAN interface
IP source everything
Destination IP everything
Save
Permitted action
RDP service
The source WAN interface
Source IP - xx.xx.xx.xx
Destination IP - xx.xx.xx.xx
Save
-Tom
Please mark replied messages useful -
How to use Layer 2 Ports on the Cisco 1841 router switch
Hello
I use the Cisco 1841 router with a single port layer 3 Fe0 and 8 Ports switched.
I gave the IP on the Fe0 port which is connected to another router.
Now I don't know how to use Layer 2 of the router switch ports.
I tried to make one of the port as a Port of access by switchport mode access and connected my laptop and the same subnet given IP, but I can't ping my Fe0 IP port and vice versa, as I am also unable to ping my laptop router.
Can someone explain to me how to use these ports on layer 2?
Hi Muhammadatifmasood, take a look at the link below, I'm sure that you will find it useful.
https://supportforums.Cisco.com/discussion/10919631/how-enable-routing-b...
BenSamayoa
-
SSL VPN may be configured on the router from Cisco 881/K9?
I'm now confused if SSL VPN can be configured on the router from Cisco 881/K9.
Please someone advise me.
If Yes, for only 5 users, what I need to buy the license or license is supplied with the router?
Thank you.
Yes, and you need a license:
FL-WEBVPN-10-K9
License SSL VPN functionality for up to 10 users (incremental), to 12.4 T based only IOS versions
FL-SSLVPN10-K9
License SSL VPN functionality for up to 10 users (incremental) for the only based 15.x IOS versions
-
Wireless router / Internet problems
I am running Windows Vista Home Edition with Security Essentials. I can connect to my wireless router, but cannot get internet connectivity via Wireless. If I connect the cable to the port on the router, I get internet connectivity. Is there a firewall setting that could cause this problem?Hello
Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
Update your WiFi drivers on computers. How you are positioned in the router? Are there
obstacles in the path?Actually try updating your driver and disabling the network logon.
Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlDownload - SAVE - go where you put it - right click – RUN AS ADMIN.
You can download several at once however restart after the installation of each of them.
After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
manufacturer of system become your backup policies).Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
updated drivers.I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
are almost always old, and you can search drivers manually as needed.How to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx------------------------------------------------------
Make sure you know the details of connection to your wireless router - SSID and password.
You lose connection when you do and have to redo your logon.
Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
lower left click on merge or delete network locations - REMOVE all instances of your network (and the
others you don't use anymore) - REBOOT. Start - Connect To log on to the network.-----------------------------------------------------
Check this box:
Strange problem with Internet under Vista
http://www.catonett.com/blog/archives/194Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
http://support.Microsoft.com/kb/928233/en-us----------------------------------------------------
And:
Network connection problems
http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
-
Configure the router Cisco E2000 wireless for my laptop HP with Vista, I can't work.
Configure the router Cisco E2000 wireless for my laptop HP with Vista, I can't work. I spoke with Cisco and they said that my Atheros AR5007 adapter does not work with Cisco E2000 and contact my computer vendor
Hello
HM... I guess that the Cisco people know what they're taking everything. The AR5005 is a b/g card and there should be a good reason to not work with a router that is able (the E2000 is able g) g.
This is HP drivers for the card, http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?cc=us&lc=en&dlc=en&softwareitem=ob-55737-1
If you can't make it work, you must decide between a new card or another router.
Personally, if it's new and I could return it, I'd get a different router model. But YMMV
------------
My posts reflect my understanding and experience. It does not necessarily reflect the opinion or the vision of Microsoft, or anyone else.
Jack-MVP Windows Networking. WWW.EZLAN.NET
Maybe you are looking for
-
I have a 2 TB USB (USB 2.0).
I tried to use Time Machine this weekend. After 2 days and nights he had only supported 9 GB out of 150 GB total. "Way to slow to be useful as any kind of a backup. How this Setup go faster? MackBook Pro 15-inch, mid-2012, ElCapitan 10.11.6.
-
Changing account to another country and iTunes game
I moved from the Australia to the United Kingdom, and need to change the itunes store in the United Kingdom today, so that I can use my new UK credit card and also use UK of specific applications, such as the BT wireless application, which is availab
-
A young man is spend too much time on his iPhone surf. What can we cope with this? Is it possible to limit the time to surf, for a period of time (hour, day, week)?
-
I have 2 questions related to LabVIEW Real-time. I'm using LabVIEW 2010 Service Pack 1. We have a PXI-8186 controller running the embedded real-time. (1) I have my software written to communicate using TCP/IP. The real time software runs the listener
-
Hey all,. I'm pushing a new page, if a user clicks on an image... must be right straight forward? tried with a button as well... am I missing something? import bb.cascades 1.0 NavigationPane { id: navPane backButtonsVisible: false Page { Container {