Router ISR Cisco 1941 with ISDN lines.

Are there any card that can support the IRB on the ISR1941?

Thank you

It is not on the same page: VIC2-2BRI-NT/TE

Tags: Cisco Network

Similar Questions

Help to configure the router Cisco 1941

Help!

I just bought a router cisco 1941, I understand, it came with the Cisco CP, but I don't know how get you to the part where I can use it.

Also, how can I connect to the router directly without using the HyperTerminal console, all I want to be able to do is configure the address IP of the ISP and my IP address so I can use it for surfing the internet.

Help, please.

Hello

Thanks for the screenshots and show the output! You will need a few lines of command for CCP to work:

Configure the terminal

username username privilege 15 secret PASSWORD

IP http server

local IP authentication

Sent by Cisco Support technique iPad App

Cisco 1941: no risk in "ip Routing" or "ip cef" for NetFlow when bypass

Hello

It's on a router Cisco 1941. version 15.1 ipv4 only.

I would like to enable Netflow v9 for use with PRTG bandwidth monitoring.

I tried the instructions at http://kb.paessler.com/en/topic/563-do-you-have-any-configuration-tips-for-cisco-routers-and-prtg and the first step fails because I

no ip Routing

No cef

in my running-config. More precisely, this
```
 interface GigabitEthernet 0/1 ip route-cache flow exit 
```
fails with the error message "ip Routing not enabled."

I have read conflicting information on the question if I need to change one or both of these lines. And I have enough to http://www.cisco.com/c/en/us/td/docs/ios/15_1/release/notes/15_1m_and_t/151-4MCAVS.html afraid to try just scanned.

I hope that's enough of my config for someone to give some useful information. Note the BYPASS.

interface GigabitEthernet0/0 no ip address no ip redirects no ip unreachables no ip route-cache load-interval 30 duplex auto speed auto no cdp enable no mop enabled bridge-group 1 bridge-group 1 spanning-disabled ! interface GigabitEthernet0/1 bandwidth 10000 ip address 201.201.201.51 255.255.255.0 ip access-group 110 in ip access-group 120 out no ip redirects no ip unreachables no ip route-cache load-interval 30 duplex auto speed 10 no cdp enable bridge-group 1 bridge-group 1 spanning-disabled ! ip default-gateway 201.201.201.1 ip forward-protocol nd ! no ip http server no ip http secure-server ip flow-export version 9 ip flow-export destination 201.201.201.89 9991

Looking forward to comments from a person with experience, do something similar.

Thank you.

We do not know anything about your environment or why you decided to activate ip Routing and fill. But there is probably a reason why you did that.

The importance of this is that NetFlow data are generated as part of the routing decisions. And you prevent your router to make routing decisions as you have disabled ip Routing. So I don't see anyway that you can get this router NetFlow, as long you have disabled ip Routing.

HTH

Rick

Router Cisco 1941 - crypto isakmp policy command missing - IPSEC VPN

Hi all

I was looking around and I can't find the command 'crypto isakmp policy' on this router Cisco 1941. I wanted to just a regular Lan IPSEC to surprise and Lan installation tunnel, the command isn't here. Have I not IOS bad? I thought that a picture of K9 would do the trick.

Any suggestions are appreciated

That's what I get:

Router (config) #crypto?
CA Certification Authority
main activities key long-term
public key PKI components

SEE THE WORM

Cisco IOS software, software C1900 (C1900-UNIVERSALK9-M), Version 15.0 (1) M2, VERSION of the SOFTWARE (fc2)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Updated Thursday, March 10, 10 22:27 by prod_rel_team

ROM: System Bootstrap, Version 15.0 M6 (1r), RELEASE SOFTWARE (fc1)

The availability of router is 52 minutes
System returned to ROM by reload at 02:43:40 UTC Thursday, April 21, 2011
System image file is "flash0:c1900 - universalk9-mz.» Spa. 150 - 1.M2.bin.
Last reload type: normal charging
Reload last reason: reload command

This product contains cryptographic features...

Cisco CISCO1941/K9 (revision 1.0) with 487424K / 36864K bytes of memory.
Card processor ID FTX142281F4
2 gigabit Ethernet interfaces
2 interfaces Serial (sync/async)
Configuration of DRAM is 64 bits wide with disabled parity.
255K bytes of non-volatile configuration memory.
254464K bytes of system CompactFlash ATA 0 (read/write)

License info:

License IDU:

-------------------------------------------------
Device SN # PID
-------------------------------------------------
* 0 FTX142281F4 CISCO1941/K9

Technology for the Module package license information: "c1900".

----------------------------------------------------------------
Technology-technology-package technology
Course Type next reboot
-----------------------------------------------------------------
IPBase ipbasek9 ipbasek9 Permanent
security, none none none
given none none none

Configuration register is 0 x 2102

You need get the license of security feature to configure the IPSec VPN.

Currently, you have 'none' for the security feature:

----------------------------------------------------------------
Technology-technology-package technology
Course Type next reboot
-----------------------------------------------------------------
IPBase ipbasek9 ipbasek9 Permanent
security, none none none
given none none none

Here is the information about the licenses on router 1900 series:

http://www.Cisco.com/en/us/partner/docs/routers/access/1900/hardware/installation/guide/Software_Licenses.html

Newbie Help Needed: Cisco 1941 router site to site VPN traffic routing issue

Hello

Please I need help with a VPN site-to site, I installed a router Cisco 1941 and a VPN concentrator based on Linux (Sophos UTM).

The VPN is established between them, but I can't say the cisco router to send and receive traffic through the tunnel.

Please, what missing am me?

A few exits:

ISAKMP crypto to show her:

isakmp crypto #show her

IPv4 Crypto ISAKMP Security Association

DST CBC conn-State id

62.173.32.122 62.173.32.50 QM_IDLE 1045 ACTIVE

IPv6 Crypto ISAKMP Security Association

Crypto ipsec to show her:

Interface: GigabitEthernet0/0

Tag crypto map: QRIOSMAP, local addr 62.173.32.122

protégé of the vrf: (none)

local ident (addr, mask, prot, port): (192.168.20.0/255.255.255.0/0/0)

Remote ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)

current_peer 62.173.32.50 port 500

LICENCE, flags is {origin_is_acl},

#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

#pkts decaps: 52, #pkts decrypt: 52, #pkts check: 52

compressed #pkts: 0, unzipped #pkts: 0

#pkts uncompressed: 0, #pkts compr. has failed: 0

#pkts not unpacked: 0, #pkts decompress failed: 0

Errors #send 0, #recv 0 errors

local crypto endpt. : 62.173.32.122, remote Start crypto. : 62.173.32.50

Path mtu 1500, mtu 1500 ip, ip mtu IDB GigabitEthernet0/0

current outbound SPI: 0x4D7E4817 (1300121623)

PFS (Y/N): Y, Diffie-Hellman group: group2

SAS of the esp on arrival:

SPI: 0xEACF9A (15388570)

transform: esp-3des esp-md5-hmac.

running parameters = {Tunnel}

Conn ID: 2277, flow_id: VPN:277 on board, sibling_flags 80000046, crypto card: QRIOSMAP

calendar of his: service life remaining (k/s) key: (4491222/1015)

Size IV: 8 bytes

support for replay detection: Y

Status: ACTIVE

Please see my config:

crypto ISAKMP policy 1

BA 3des

md5 hash

preshared authentication

Group 2

encryption... isakmp key address 62.X.X... 50

ISAKMP crypto keepalive 10 periodicals

!

!

Crypto ipsec transform-set esp-3des esp-md5-hmac TS-QRIOS

!

QRIOSMAP 10 ipsec-isakmp crypto map

peer 62.X.X set... 50

transformation-TS-QRIOS game

PFS group2 Set

match address 100

!

!

!

!

!

interface GigabitEthernet0/0

Description WAN CONNECTION

62.X.X IP... 124 255.255.255.248 secondary

62.X.X IP... 123 255.255.255.248 secondary

62.X.X IP... 122 255.255.255.248

NAT outside IP

IP virtual-reassembly in

automatic duplex

automatic speed

card crypto QRIOSMAP

!

interface GigabitEthernet0/0.2

!

interface GigabitEthernet0/1

LAN CONNECTION description $ES_LAN$

address 192.168.20.1 255.255.255.0

IP nat inside

IP virtual-reassembly in

automatic duplex

automatic speed

!

IP nat pool mypool 62.X.X... ... Of 122 62.X.X 122 30 prefix length

IP nat inside source list 1 pool mypool overload

overload of IP nat inside source list 100 interface GigabitEthernet0/0

!

access-list 1 permit 192.168.20.0 0.0.0.255

access-list 2 allow 10.2.0.0 0.0.0.255

Note access-list 100 category QRIOSVPNTRAFFIC = 4

Note access-list 100 IPSec rule

access-list 100 permit ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

access-list 101 permit esp 62.X.X host... 50 62.X.X host... 122

access list 101 permit udp host 62.X.X... 50 62.X.X... host isakmp EQ. 122

access-list 101 permit ahp host 62.X.X... 50 62.X.X host... 122

access-list 101 deny ip any any newspaper

access-list 110 deny ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

access-list 110 permit ip 192.168.20.0 0.0.0.255 any

!

!

!

!

sheep allowed 10 route map

corresponds to the IP 110

The parts of the configuration you posted seem better than earlier versions of the config. The initial problem was that traffic was not in the VPN tunnel. That works now?

Here are the things I see in your config

I don't understand the relationship of these 2 static routes by default. It identifies completely the next hop and a mask the bytes of Middleweight of the next hop. Sort of, it seems that they might be the same. But if they were the same, I don't understand why they both make their appearance in the config. Can provide you details?

IP route 0.0.0.0 0.0.0.0 62.X.X... 121

IP route 0.0.0.0 0.0.0.0 62.172.32.121

This static route implies that there is another network (10.2.0/24) connected through the LAN. But there is no other reference to it and especially not for this translation. So I wonder how it works?

IP route 10.2.0.0 255.255.255.0 192.168.20.2

In this pair of static routes, the second route is a specific subnet more and would be included in the first and routes for the next of the same break. So I wonder why they are there are. There is not necessarily a problem, but is perhaps something that could be cleaned up.

IP route 172.17.0.0 255.255.0.0 Tunnel20

IP route 172.17.2.0 255.255.255.0 Tunnel20

And these 2 static routes are similar. The second is a more precise indication and would be included in the first. And it is referred to the same next hop. So why have the other?

IP route 172.18.0.0 255.255.0.0 Tunnel20

IP route 172.18.0.0 Tunnel20 255.255.255.252

HTH

Rick

When you try to add a network route with the "route add" command in the command line, I get the message "the requested operation requires a rise."

Elevation required to route add command

When you try to add a network route with the "route add" command in the command line, I get the message "the requested operation requires a rise." What is the correct syntax to use?

You can watch using the PowerShell...

http://TechNet.Microsoft.com/en-us/library/bb978526.aspx

http://TechNet.Microsoft.com/en-us/scriptcenter/dd742419.aspx

.. .and post questions about Windows PowerShell forum...

http://social.technet.Microsoft.com/forums/en/winserverpowershell/threads

Help to activate SSL VPN router Cisco 1941

Hello.

I have a router Cisco 1941 and want to activate my SSL VPN license on it. How can I go about it?

Best regards Tommy Svensson

Hi Tommy,.

Please try and download the PDF of the same link.

I hope this helps.

Kind regards

Anisha

P.S.: Please mark this message as answered if you feel that your request is answered. Note the useful messages.

HOWTO configure SSL VPN router Cisco 1941?

Hello.

How to configure SSL VPN on a router Cisco 1941? I would like a howto guide that is step by step. I've found myself so far.

Best regards Tommy Svensson

Here are a few links that might help:

http://www.Cisco.com/en/us/products/ps6657/prod_configuration_examples_list.html

http://security-blog.netcraftsmen.NET/2009/02/Cisco-IOS-SSL-VPN-example.html

Cisco 1941 hit crypto speed limit

I have read the documentation about the 85Meg / 170 Meg limit on the SRI G2s

As far as I know - this does NOT apply to the 1941.

I have a 1941 with sec - k9 license, you can not buy a license of h - s for this device.

The SSEC-K9 license removes the reduction applied by the US Government on the encrypted tunnel and encrypted flow export restrictions. SSEC-K9 is available only on the Cisco 2921, 2951 Cisco, Cisco 3925, 3945 Cisco, Cisco 3925th and 3945TH Cisco.

With the SSEC-K9 license, the ISR G2 router can go above the limit of the reduction of the maximum of 225 tunnels for IP (IPsec) security and the flow rate of 85 Mbps of one-way traffic in or out the ISR G2 router encrypted, with a total of 170 Mbps bidirectional / s.

Cisco 1941 and 2901 2911 already have maximum encryption within the limits of export capabilities. The HSEC license requires pre-installed image of the universalk9 and the DRY license. »

I took this means that '1941 and 2901 2911' must go faster than that? It seems that they are limited to 85Mbit!

MEL-4-TX_BW_LIMIT %: bandwidth limit Maximum Tx 85000 Kbps reached for the cryptographic functionality with technology securityk9 package license.

Can anyone confirm if they got more than 85 Mbps out of one of these devices? FYI, I'm not nat'ing nothing - this is purely static device VTI. Ive sent the packages using iPerf via this device @ 500 + Mbit.

Well, you can communicate with Cisco and talk to them about your concerns about the text of this. It would probably help others in the future also.

Regarding this site selling the 1941 with license of k9 SSEC, according to me, is either a typo or that they do not know the product.

According to this document the 1941 has the regular permit of K9 SEC available to her.

1900	CISCO1941-SEC/K9	License of Cisco 1941 PAK, 256 MB of DRAM Security Bundle w/sec
	CISCO1941W-SEC/K9	Cisco 1941W Security Bundle w/sec license PAK, 802.11a/b/g/n

Please do not forget to select a correct answer and rate useful posts

Internet works is not in LAN behind a router from Cisco 881

My internet does not work in local network that is behind the router from Cisco 881. Here is the configuration of the router.

Help, please...

Current configuration: 1478 bytes
!
! Last modification of the configuration at 08:16:12 UTC Wednesday, February 6, 2036
!
version 15.1
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname R1
!
boot-start-marker
boot-end-marker
!
enable secret 5 CATz $1$ $ VqnIsAQvFHHnV9E/Q6RMV0
!
No aaa new-model
iomem 10 memory size
!
!
IP source-route
!
!
DHCP excluded-address IP 192.168.1.1
!
IP dhcp pool dhcppool1
import all
network 192.168.1.0 255.255.255.0
default router 192.168.1.1
DNS-server 202.56.230.2 202.56.230.7
!
!
IP cef
name of the IP-server 202.56.230.2
name of the IP-server 202.56.230.7
No ipv6 cef
!
!
license udi pid CISCO881-K9 sn FGL1539254Q
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
IP 182.73.122.54 255.255.255.252
NAT outside IP
IP virtual-reassembly
automatic duplex
automatic speed
!
interface Vlan1
IP 192.168.1.1 255.255.255.0
IP nat inside
IP virtual-reassembly
!
router RIP
version 2
network 192.168.1.0
!
IP forward-Protocol ND
IP http server
no ip http secure server
!
overload of IP nat inside source list 101 interface FastEthernet4
IP route 0.0.0.0 0.0.0.0 182.73.122.53
!
access-list 101 permit ip 0.0.0.0 255.255.255.0 any
!
!
!
!
!
control plan
!
!
Line con 0
exec-timeout 5 30
password vinayak123
opening of session
no activation of the modem
line to 0
line vty 0 4
password vinayak123
opening of session
transport of entry all
!
end

Hello @[email protected] / * /;

Thank you for your message. I had a glance on the configuration for you. You used a network as opposed to a wild card mask in your access control list for your NAT statement. This changed the field from the source to 0.0.0.0 automatically, which is going to be does not match your interior traffic and NAT'ing outside.

To fix this, please run the following commands and test once more.
```
no access-list 101access-list 101 permit ip 192.168.1.0 0.0.0.255 any
```
Thank you
Luke
Please evaluate the useful messages and mark the correct answers.

SSL VPN may be configured on the router from Cisco 881/K9?

I'm now confused if SSL VPN can be configured on the router from Cisco 881/K9.

Please someone advise me.

If Yes, for only 5 users, what I need to buy the license or license is supplied with the router?

Thank you.

Yes, and you need a license:

FL-WEBVPN-10-K9

License SSL VPN functionality for up to 10 users (incremental), to 12.4 T based only IOS versions

FL-SSLVPN10-K9

License SSL VPN functionality for up to 10 users (incremental) for the only based 15.x IOS versions

Red circle with a line through

I look a my email, hit something on my keyboard and I had a red circle with a line through it on my email that I look one including all the others with the same subject / receiver. Now, emails are no longer there and I have not received all messages from this person either, at least not through Thunderbird. I don't know what I did. Any help is greatly appreciated.

Thank you

Mark

See Menu (Alt + V) > discussions > ignored threads

See https://support.mozilla.org/en-US/kb/ignore-threads

I can't add bookmarks to the bookmarks toolbar - get a circle with a line though it.

Updated for Firefox 13... She has not any of the previous version went to build a new bookmarks toolbar and when I tried to drag an item from the Web site to the toolbar (as I used to be able to do easily in the previous version) I had a circle with a line through it - which basically said sorry you can do. Backgraded to 12 Version and I have the same problem. I don't have any extensions running. The bookmarks bar is checked (forthcoming) and there is an empty up there... just cannot add anything to it. Any suggestions on what I may be missing would be appreciated. I wouldn't give up this late date on Firefox. Thank you!

Well, I'm embarrassed to admit that I followed all of your suggestions with little chance... but then I started to 'pitch and putt' with practically everything what they allowed me to view and customize both and to the high jump bar Bookmarks imported when I've updated - but was not showing... I suspect it was the thing to restore default setting that worked at one point. (I'm definitely NOT a geek as you might have guessed.) But what worries me is that I don't really know what I did, and if I go on another machine and have the same problem I'm going to start on (but knowing that I CAN fix it if I'm persistent). Thanks for all the suggestions! I'm back with Firefox again.

I can't create a shortcut to the site on my desktop, when I click on the url bar I can drag on the browser to open a new, but as I drag him on my desktop I get the circle with the line through it, one that looks like a no entry sign. Help?

I can't create a shortcut to the site on my desktop, when I click on the url bar I can drag on the browser to open a new, but as I drag him on my desktop I get the circle with the line through it, one that looks like a no entry sign. Help

Try to drag the image to id web site (favicon) on the left side of the address bar, instead of the URL.

Icon has a circle with a line through it, so I can't move the icon to dock... why? Fix > |?

Icon of Firefox which is shown to go in my applications folder
a circle with a line through it, which does not allow me to drag the icon
in my dock for us opening and closing of browser... why? And how
can I get rid of this circle?

I deleted an earlier version of FFox so I hae no icon to open with.
I get message that says Ffox can not open - please help.
```
thx. weidner
```
http://www.Mozilla.com/en-us/Firefox/4.0/system-requirements/

Mozilla Firefox 4.0 does not support Mac PPC or versions prior to 10.5.

For older Macs that are not considered supported in Firefox 4.0, try TenFourFox for PowerPC in performance Mac 10.4.11 and 10.5.8.

http://www.floodgap.com/software/tenfourfox/

Router ISR Cisco 1941 with ISDN lines.

Similar Questions

Hello @[email protected] / * /;

To fix this, please run the following commands and test once more.

Thank you

Luke

Please evaluate the useful messages and mark the correct answers.

Maybe you are looking for