Routing EasyVPN

Similar Questions

• Installation of ASA EasyVPN - cannot ping loopback on router CME

  Hello

  I don't know if it is a problem of firewall or something on my router, so I thought I would start here.  I have an ASA 5505 at home that I use as a client for the purpose of connecting a Cisco IP phone to a CME No. 2851 router EasyVPN.  At the office, I have an ASA 5510, which acts as the EasyVPN server.  The CME router loopback address is 10.1.254.254, and the router's ethernet interfaces are 10.2.100.50 and 10.1.100.1.  The customer EasyVPN receives an address 192.168.100.1 the EasyVPN server.

  In my house, if I connect a computer to my ASA 5505 VPN is based and I can ping all my hosts interns (at the office), and I can ping both interfaces of the router.  If I try to ping the router loopback address I get nothing.   If I start the router and work my way to the EasyVPN (ASA 5510) Server I can ping the loopback address of the router to the power switch and then the ASA5510. I think it's a problem of firewall because of the capture, I install both inside the ASA interfaces:

  If I ping 10.2.100.50 or 10.1.100.1, I see the echo and echo on the ASA5505 responses, and I see them on the ASA5510 - successfully running through the VPN tunnel.

  If I ping 10.1.254.254, I see the echo to the ASA5505 request, but I don't see anything on the ASA5510.

  I checked my nat_exemption on the ASA5510 and I have an entry like this:

  nat_exemption list of allowed ip extended access any 192.168.100.0 255.255.255.128

  I can provide more if necessary configs, but anybody have any ideas where I'm wrong?

  Thanks in advance,

  Brandon

  Brandon,

  I would like to start showing us "crypto ipsec to show its" on your home 5505.

  Then the station we would need:

  --------

  See the establishment of performance-crypto

  See running nat setting

  See the global race

  See the static race

  See the tunnel-group race

  ---------

  Ideally I would allow newspapers on informqtional level on headboard and ASA local.

  Run the ping command and check:

  -------

  Show logg. I have 10.1.254.254

  -------

  We are looking for connections being built or any "deny" messages.

  Marcin

• Customer router how EasyVPN join two easy VPN servers?

  I have a router in the branch with dynamic ip address, configured as a client of EasyVPN (network extension mode) needs to connect to both servers (two other branches with static Ip) Easyvpn,... is this possible? and how to do io?

  On the HUB router, you can try without the isakmp profile:

  Crypto-map dynamic dynmap 10
  no set isakmp profile L2L

  and also keep the following:

  ISAKMP crypto cisco123 key address 0.0.0.0 0.0.0.0

  Post edited by: Jennifer Halim

• EasyVPN and Pix501-Pix501-problem

  Hello

  I have a problem with my two Pix501.

  I want one of them is the EasyVPN server and the other is the Client remote EasyVPN.

  I configured everything as it is shown at http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a008019e6d7.shtml

  I have my 'normal' network 192.168.0.0/24 which is the external interface of the two PIX in my testenvironment. EasyVPN-network 192.168.1.0/24 the otherone servers are 192.168.2.0/24.

  My problem is, that the two PIX do not connect.

  Here are the configs:

  EasyVPN server:

  6.3 (5) PIX version
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 8Ry2YjIyt7RRXU24 encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  hostname kr01icr02
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  192.168.0.220 outside IP address 255.255.255.0
  IP address inside 192.168.1.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  IP local pool ippool 192.168.3.1 - 192.168.3.254
  PDM logging 100 information
  history of PDM activate
  ARP timeout 14400
  Global 1 interface (outside)
  (Inside) NAT 0-list of access 101
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Route outside 0.0.0.0 0.0.0.0 192.168.0.250 1
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  Crypto ipsec transform-set RIGHT aes - esp esp-md5-hmac
  Crypto-map dynamic dynmap 10 transform-set RIGHT
  map mymap 10-isakmp ipsec crypto dynamic dynmap
  mymap outside crypto map interface
  ISAKMP allows outside
  ISAKMP identity address
  part of pre authentication ISAKMP policy 10
  ISAKMP policy 10 aes encryption
  ISAKMP policy 10 md5 hash
  10 2 ISAKMP policy group
  ISAKMP life duration strategy 10 86400
  vpngroup address ippool pool mygroup
  vpngroup dns 192.168.1.200 server mygroup
  vpngroup wins 192.168.1.200 mygroup-Server
  vpngroup mygroup by default-field cisco.com
  vpngroup split tunnel 101 mygroup
  vpngroup idle time 1800 mygroup
  mygroup vpngroup password *.
  vpngroup idle-idle time 1800
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  dhcpd address 192.168.1.2 - 192.168.1.33 inside
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  dhcpd allow inside
  Terminal width 80
  Cryptochecksum:4967199c613b5553f9bc5aaa09aa02b3
  : end

  Client:

  6.3 (5) PIX version
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 8Ry2YjIyt7RRXU24 encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  hostname kr01icr03
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  external IP 192.168.0.221 255.255.255.0
  IP address inside 192.168.2.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  PDM logging 100 information
  history of PDM activate
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Route outside 0.0.0.0 0.0.0.0 192.168.0.250 1
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-server local LOCAL Protocol
  Enable http server
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  dhcpd address 192.168.2.2 - 192.168.2.33 inside
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  dhcpd allow inside
  vpnclient 192.168.0.220 Server
  vpnclient mode network-extension-mode
  vpnclient mygroup vpngroup password *.
  vpnclient enable
  Terminal width 80
  Cryptochecksum:3caebce68a73c906150eb011e7b18f8a
  : end

  Anyone have an idea why it doesn't work?

  Thank you

  Kriss

  OK, thanks for the tests and the great to hear the client software vpn works great. This eliminates the problem vpn server.

  You will also need to add the following on the client:

  vpnclient nem-st-autoconnect

  connect vpnclient

• EasyVpn

  I managed to create a tunnel between our router cisco ASA 5510 using easyvpn.

  I currently running in mode Plus network where the router receives an ip address from the ASA when it connects from its pool. However, this will change with each connection.

  I changed it to network-Extension in the hope, the router to connect and be managed with its own ip, but it fails to connect.

  What should I put on the ASA to allow the connection to use its own ip address?

  You must activate the NEM on SAA for it to work using the cmd:

  # nem enable

• EasyVPN and access VPN remotely on the same box

  Is it possible to have a config EasyVPN and remote access in the same box? I tried to do that and when I do a vpnclient enable command he said remote NAT (outside) 0

  Router IOS or PIX? EzVPN server or client?

  If it's EzVPN server, then it's basically a configuration of remote access also, then Yes, you can certainly have them both, actually just set one up and you get one anyway.

  If it's EzVPN client, then no if it is a PIX and Yes if it's a router, but you must run 12.2 (15) T, see http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t15/ftezvpnr.htm#1155828 for more details.

  Please answer back with more information on exactly what you're trying to do, it is a little difficult to your original explanation.

• Connect a Cisco L3 switch behind a 871 using easyvpn

  Hello

  It is our habit to use easyvpn on 871 routers to connect our remote to our ASA 5500 VPN concentrators.

  It works well, we define them VLAN on the 871 and connect Cisco L2 switches behind the VPN routers.

  Problem is that now we have to connect the Cisco L3 switch behind the VPN routers and if we face problems of routing...

  No way to make works for all the VLAN defined on the switch of L3!

  I guess we have to use a specific configuration (IRB?).

  Or do we have to use IPSEC-L2L instead of the easyvpn?

  Thanks for your help.

  Kind regards

  Patrick Lee

  Patrick,

  It will certainly benefit you started.

  You can google some more for that.

  Someone posted this on the forums, but I think you might want to ask them

  https://supportforums.Cisco.com/docs/doc-3066;JSESSIONID=444194CDE250004E116705FF0ADAD955. Node0

  I hope this helps.

  Marcin

  Edit: many thing depend on whether you use NEM and if you plan to use. If you in any qustions stumple - post here.

• 6500 IOS router Cisco VPN Client using DHCP no Pool of IP

  Hey guys,.

  I have a little trouble trying to get my vpn client to use a dhcp server rather than the pool of intellectual property.  When I use the command IP pool everything works fine, but when I use the dhcp command I get an error on the client-side saying that no address private IP was affected by the peer.

  Here is my config.

  connection of AAA VPNCLIENT_AUTHEN group local RADIUS authentication

  local VPNCLIENT_AUTHOR AAA authorization network

  Configuration group customer isakmp crypto VPNCLIENT_GROUP

  xxxxxxxxxxxxxxxxxxxxxxxxxx key

  DNS 172.25.128.43 172.25.65.43

  win 172.25.1.54

  sktnhr.ca field

  172.25.0.27 DHCP server

  GIADDR DHCP 172.25.205.1

  DHCP timeout 10

  pool # VPNCLIENT_IPPOOL

  Crypto isakmp ISAKMP_PROFILE profile

  VRF HUB_VRF

  match of group identity VPNCLIENT_GROUP

  list of authentication of client VPNCLIENT_AUTHEN

  VPNCLIENT_AUTHOR of ISAKMP authorization list.

  client configuration address respond

  crypto dynamic-map DYN_MAP 1020

  game of transformation-ESP-AES-256-SHA

  ISAKMP_PROFILE Set isakmp-profile

  market arriere-route

  card crypto HUB_CRYPTO_MAP 6005-isakmp dynamic ipsec DYN_MAP

  local IP VPNCLIENT_IPPOOL 172.25.205.25 pool 172.25.205.250

  I can see the dhcp request and offer on my dhcp server but nothing is for the customer.  When I use a pool I ping the dhcp server, which makes me think the roads are okay.  Anyone has any ideas.

  You need the giaddr in an EasyVPN server configuration.  Try adding looping to your switch and test it again.  If you use an iVRF, make sure that the closure is in the VRF and the interface to the server.

• 867 EasyVPN server: Intermittent client connectivity

  I have a rather peculiar question with a particular router, which I use as an EasyVPN server.

  Customers have no problem to connect to the router. The Cisco VPN Client connects without problems and without fail every time.

  HOWEVER

  This does not mean that the customer can obtain from the server, which is located behind the router, to which they connect.

  They might be able to. They might not! It seems to vary randomly. Sometimes the client will connect, and the server will be accessible. Othertimes, the client will connect and it will not.

  Now, to do some very preliminary tests, I am STILL able to ping the router LAN interface once the tunnel is up. However, I may or may not be able to ping the server.

  Yesterday, for example, the connection came. I was able to ping an IP address on the local network of 192.168.0.9. The router is 192.168.0.15, I have, as mentioned above, ping without problem as well. However, the server, which is 192.168.0.1, was not accessible. After a couple disconnects / reconnect to the VPN client, I could ping 192.168.0.1 (and 192.168.0.15) and if I could get on the server without problem... However, I could no longer ping 192.168.0.9.

  It almost feels "subnetty", but there is nothing defined on the router that should cause this problem I can say. Clients receive an IP address in the range of 10.10.10.5 to 10.10.10.15 on a looping with IP 10.10.10.1.

  Specific no reason why the pool overlaps the closure? being a virtual interface should not make a difference on where the traffic is sent, the EFC plays sometimes strange games.

  If it's not too much to ask, you can disable this loopack?

• 1760 router VPN Config request

  Hello

  I want to program a router 1760V to support VPN remote 3DES IPSEC to support approximately 5 Cisco VPN clients on the Internet. I will appreciate if you have a config for it.

  Thank you

  -Nasser.

  It is an example of configuring ipsec router to router and client:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080094685.shtml

  Example for EasyVPN, CVPN client to the router:

  http://www.Cisco.com/warp/public/732/tech/security/IPSec/docs/ClientServer.PDF

  Kind regards

  Mustafa

• Do I need a security license to set up VPN on the router?

  Hi all.

  I am trying to setup on 2 different routers VPN connections and I'm not sure what I have needed a permit from security to configure the VPN router?

  The first is 1941-K9 site-to-site.

  Second, one is 887G - K9, EasyVPN connection.

  Two of them are not working. What should I check on both routers to see if they are valid for the vpn connection, perhaps some controls as well.

  Thanks in advance.

  Kind regards

  Yes, for the VPN, you need a security license.

  The 1941 should show the following line:

  RTR-01 #sh worm | b technology

  Technology for the Module package license information: "c1900".

  ----------------------------------------------------------------

  Technology-technology-package technology

  Course Type next reboot

  -----------------------------------------------------------------

  IPBase ipbasek9 ipbasek9 Permanent

  Security securityk9 Permanent securityk9

  given none none none

  The 887 comes by default with all features "Advanced Security". That's all you need for this device.

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• EasyVPN for VPN phones?

  Can I use a router 2911 like EasyVPN server for VPN phones or EasyVPN is only for the router-to-router VPN?

  EasyVPN server can stop sessions IPSec client.  I know not at all with native features of IPSec Cisco phones. There is version phone Cisco AnyConnect SSL VPN support including a 2911 can be dismissed to support.

  http://www.Cisco.com/en/us/customer/docs/voice_ip_comm/cucme/Admin/Configuration/Guide/cmevpn.html#wp1019169

  Todd

• Server ezvpn 887 router for remote access

  Hello.

  I'm having a problem with the implementation of remote access using easyvpn server on a router 887.  I followed the tutorials and also used Assistant cisco configuration professional easyvpn server to the configuration but still having a problem.

  I see, but Phase 1 finished, Phase 2 will fail with the following error...

  09:43:26.515 Oct 10: ISAKMP: (2003): check IPSec proposal 8

  09:43:26.515 Oct 10: ISAKMP: turn 1, ESP_AES

  09:43:26.515 Oct 10: ISAKMP: attributes of transformation:

  09:43:26.515 Oct 10: ISAKMP: authenticator is HMAC-SHA

  09:43:26.515 Oct 10: ISAKMP: key length is 128

  09:43:26.515 Oct 10: ISAKMP: program is 1 (Tunnel)

  09:43:26.515 Oct 10: ISAKMP: type of life in seconds

  09:43:26.515 Oct 10: ISAKMP: service life of SA (IPV) 0x0 0 x 20 0xC4 0x9B

  09:43:26.515 Oct 10: ISAKMP: (2003): atts are acceptable.

  09:43:26.515 Oct 10: IPSEC (validate_proposal_request): part #1 the proposal

  09:43:26.515 Oct 10: IPSEC (validate_proposal_request): part #1 of the proposal

  (Eng. msg key.) Local INCOMING = 88.xx.xxx.174:0, distance = 80.177.185.185:0,.

  local_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),

  remote_proxy = 192.168.21.12/255.255.255.255/0/0 (type = 1),

  Protocol = ESP, transform = NONE (Tunnel),

  lifedur = 0 and 0kb in

  SPI = 0 x 0 (0), id_conn = 0, keysize = 128, flags = 0 x 0

  09:43:26.515 Oct 10: map_db_find_best found no corresponding card

  09:43:26.515 Oct 10: IPSEC (ipsec_process_proposal): proxy unsupported identities

  09:43:26.515 Oct 10: ISAKMP: (2003): IPSec policy invalidated proposal with error 32

  'Proxy unsupported identities' research indicates a NAT problem maybe, but I don't see where this would be.  In my view, the problem is elsewhere.

  I use the VPN Client 5.0.07.0440 and using transparent tunneling IPSec (on TCP/10000) that the client is located behind a firewall/NAT device.

  Does anyone know what may be the issue?  Attached full config.

  Hello Mick

  Before that, one more try. .

  Remote control the pfs as follows

  Profile of crypto ipsec RemoteAccess

  no set pfs group2

  Remove and add the virtual model crypto back

  type of interface virtual-Template1 tunnel

  No ipsec protection RemoteAccess tunnel profile

  Profile of tunnel RemoteAccess ipsec protection

  I hope this will solve your problem

  Henin,

• Tips to add a VPN router to my current network configuration

  Dear all

  My apologies if the answer to this question already exists, however, I searched in many situations and none seem to match what I'm after.

  I currently have an ISP modem/router in Bridge mode connected to a TC of Apple which is my wireless router, I have 2 Express airport connected to this acting as the extensors of the range.  I have a VPN service through the MyPrivate network I activate on the desired device when required and everything works fine.

  What I want to do now is to be able to use my AppleTV and burning Amazon via the VPN as well so you need to add a VPN router in the configuration.  I want to finish with 2 wireless networks running together for these devices who need VPN and those who are not.  I don't want to lose the opportunity to extend the network to express it however airport.

  If someone could explain to me if this is possible and if so how do I set up the network.

  Thanks in advance

  Mark

  Basically you would need a device that supports VPN-passthrough and VLANS for your goals of networking. MyPrivate network, seems to be a VPN SSL, which is a user-server configuration. In other words, you install a client VPN on your Mac and you connect to the VPN network MyPrivate server to establish a VPN tunnel.

  Networking two or more "separated", should be using a router that supports VLAN services. Each segment of VIRTUAL local area network, in essence, would be a separate, she either wired or wireless network or a combination of both. This would probably be the 'easiest' part for the installation program.

  Now how combining the two would be the question, and I don't know what would be the best way, or even if it is possible.

  A few thoughts:

  • Use a router that supports VLANS. Create at least two VIRTUAL LAN segments. One for Apple TV & Burns, one for Internet access in general. Connect the device to VPN client host on the first segment, and configure for Internet sharing.
  • Download a dedicated VPN network application that supports hosting of third-party VPN clients, like yours. You would still need a router that supports VLAN to provided separate network segments.
  • Hire a consultant network. Let them know what you the goals of networking and ask them to offer potential solutions.

• Time Capsule as a router

  Instead of the cable company router, can I use my time capsule to be a router?

  The time Capsule can function as a router, but not a modem. If what you provided your cable provider is a simple modem, then the time Capsule will work. However, if they actually you provided a combination modem and the router, also known as a gateway device, then it wouldn t.