RS232 data read error

Similar Questions

• Satellite A300D-135 - BIOS - System Configuration data read error

  After starting a Satellite A300D-135 laptop computer, the following error message appears:

  
  3070M extended RAM passed
  512 KB of L2 Cache
  System BIOS with a shadow
  Video BIOS with a shadow
  ATAPI CD-ROM: TSSTcorp CDDVDW TS-L632H
  Fixed disk 0: TOSHIBA MK2546GSX
  Initialized the mouse
  ERROR
  System Configuration data read error

  Press to resume, installation

  After pressing F1 the machine starts Windows, very well, but the error message is quite irritating, while it comes with a loud BEEP

  I tried the following things so far (in that particular order):
  -Load BIOS default
  -Flashed the BIOS with the latest version of the BIOS (2.80) for this type of model
  -Reinstalled windows with HARD drive format

  All the these did not work.

  I saw the same message appearing on several places on the internet (on different laptops with a Phoenix BIOS in common), but so far I have not been able to find a working solution.

  It might me a hardware problem, but all devices (vga, soiund, lan, wifi, usb, hdd) seem to work perfectly under Windows, so this does not seem the question). Another solution that is mentioned in some forums, replace the battery. But because the phone keeps time correctly I don't think it's the case either.

  Any ideas?

  Kind regards
  GJ

  Hello

  The POST (power on self-test) BIOS checks and detects errors on the motherboard.
  I think it has something to do with the hardware on the motherboard problem.
  I doubt that you can solve this if update of the BIOS and the BIOS default settings didn't change that.

  What to say; I think that the technician of the ASP should run tests to check what's wrong or what cause this I think it is question of s mobo.

• Equium A300D - 13 X - Configration system data read error

  Hello

  I have a problem with my Equium A300D - 13 X laptop, everytime I turn on my laptop it starts and loads the initial startup screen as usual, Toshiba once asked that loud "BEEP" comes from my laptop, and lists the following information:

  Phoenix TrustredCore (tm) NB
  Copyright 1985-2006 Phoenix Technologies Ltd.
  All rights reserved

  Herring of the ITA (DDR2 + T/RS690M/SB600)
  CPU speed = 2000 MHz

  639K system spent RAM
  1918M extended RAM passed
  1024 KB of L2 Cache
  Occult system BIOS
  Video BIOS with a shadow
  ATAPI CD-ROM: MAST * ADVD-RAM UJ-850 S
  Fixed disk 0: WDC W2500BEVT-00SCSTO
  Fixed disk 1: Hitachi HTS542520K9SA00
  Initialized the mouse
  ERROR
  System Configuration data read error

  Press to resume, installation

  I replaced the hard drive and flashed the BIOS settings as advised by Toshiba Helpline but the problem persists.

  Help, please! because the "BEEP" is now getting on my nerves!

  See you soon

  Hi andrew_net82,

  It seems that the BIOS has detected an error with a certain part of material...

  Before doing something I recommend you load the default settings in the BIOS. If you are in the BIOS Setup, press the F9 key.

  If it doesn t work you need for professional assistance from an authorized service I think. Guys need to check which part of the material is defective and must be replaced.
  List of the ASP, you can find on the official website of Toshiba.

• Computer laptop Gateway does not load windows Vista, reads configuration data read error: System.

  OK a friend knows me to fix his laptop. Apparently what she was experiencing major problems, so he erased the disc and tried to reinstall Win Vista from disk. Will not work. I can get to where you can choose a partition to install the operating system to, and it says: Windows cannot find a system volume that meets its criteria for installation. My friend says he has just tried, form disassemble the computer an audit of all the parties to try ALL the different options during installation, as well as the options for the BIOS. Any ideas people? Here are the approximate specifications, because the owner has not been able to get the computer working for awhile:
  4 GHz, 4 GB RAM computer Gateway laptop, 2006, Phoenix TrustedCore, and a string of other interesting info that appears on the first screen of the error:

  9D.03 BIOS version

  632K RAM passed system
  3966M extended RAM passed
  1024 KB of L2 Cache
  System BIOS with a shadow
  Video BIOS with a shadow
  ATAPI CD-ROM: Optiarc DVD RW AD-7563 has
  Fixed disk 0: WDC WD2500BEVS-26VATO
  Initialized the mouse
  Updated System Configuration data
  ERROR
  System Configuration data read error.

  I'm not very tech savy and I'm not the owner of the PC, so I don't know all about it so go easy on me :).

  If your friend tried to reinstall Windows by using the defined gateway recovery disc (and this is the best way) and this recovery fails, the laptop has hardware problems. Disassemble laptops is a fickle business at best and while it sounds like the hardware problems started before your friend did this, it may have put the nails in the coffin of the laptop to take apart.

  At this point, you can try troubleshooting hardware or your friend can take the laptop to a competent professional (not a type of BigComputerStore/GeekSquad of the place). However, if the laptop has had hard use, your friend must remember that a cell of 4 years with major hardware problems probably won't be cost effective to repair.

  http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot MS - MVP - Elephant Boy computers - don't panic!

• Satellite P200 Vista Ultimate - boot configuration data read error

  I have a Toshiba Satellite P200 running Vista Ultimate.

  Recently I started having a problem after restarting after the installation of vista updates. In fact, it will not start at all and gives me the following message on a black screen.

  Windows could not start. A recent change in hardware or software can cause of bethe. To solve the problem:

  1. Insert your windows installation disc, and then restart your computer
  2. choose your language settings, and then click Next.
  3. click on "repair your computer".

  If you do not have this disc contact your manufacturer aministrator or the computer of the help system.

  File: \Boot\BCD

  Status: 0xc00014c

  Info: An error occurred trying to read the boot configuration data.

  The only way I can fix it to insert the recovery dvd and click on repair. This levonorgestrol only when the computer restarts after an update. If I manually turn off the computer, then on start up fine.

  I don't want to put automatic offf to update more because I think they are important from the safety point of view, however, this situation is not acceptable.

  Can someone please help.
  I have a screenshot of the error, but have reproduced the information above.

  Hello

  In my opinion, there is something wrong with your mater boot (MBR) of the drive and therefore the bootloader causes an error.

  Usually, you might be able to fix it using the original disk of Vista but it s really strange that this problem still occurs after the update to vista.

  In my eyes, you should really check if the same problem would happen using the Toshiba factory settings and configuration.

  Good luck

• NIScope data read error

  I'm trying to use the attached vi(been simplified) to get NI5133 data.

  But received error as the screen attached. I use niscope Panel before a certain time is ok, sometimes the name of the boot device is gray.

  The program works great on this laptop, even once today worked. But now cannot work after reboot several times.

  Any suggestion, thank you.

  Error 1074118647 occurred at niScope read WDT.vi:4

  Possible reasons:
  A previous acquisition is still ongoing. If you attempt to change an attribute, note that you cannot change the fetch attributes while an acquisition is still ongoing.

  Have you seen this?

• Read error - SOLUTION system configuration data

  Today, I found a solution to the error of notorious boot not only on the toshiba, but some other brands also.

  The error is: System configuration data read error.
  He invites to start with 2 beeps which prevents the computer laptop Moldavian from.

  I tried everything I could to remve this message but noything helped me.
  Replace all, cmos battery, updated the bios, loader, drives, keyboard and etc.

  Today, I found a solution very simple that I want to share with you guys.
  This solution worked for me and I hope it will work for you too.

  Are you ready? :)

  Go to the Bios and change the Bios language french.

  Post here if it works for you also.

  Thanks for sharing your experience with us. But its really hard to believe that your solution would be linked to all devices such problem

  However, good to know that this small change in the BIOS has helped you to resolve the issue

• Error - looking for help to recover or restore my data reading disk Windows 7

  My Windows 7 Pro machine restarts automatically while I had an open browser window (I didn't actually see it happen) but now I just see a message that says "a disk read error has occurred. Press Ctrl + Alt + Delete to restart» By pressing this key sequence does nothing. Just see a black screen with this message.

  I have booted from the CD of Installation Win 7 then went to repair. I tried to do a system restore, but no restore points could be found, so I chose the first option. No bones were listed in the list. A few diagnostic tests was performed and I looked at the details. The series of tests except the last System Volume has been altered. It says to reboot to see if that could fix the problem. Unfortunately, it does not and I still see the same black screen with the error message. BTW, as you know, I can't start in safe mode. Also restart on a Win 7 CD now is no longer gives me an option of just complete repair install. I tried to use this boot drive as one secondary drive on another machine to Win 7, but the OS tells me I need to format the disk before it can be used.

  I'm willing to put in the time to try to get the data restored on this boot drive, but don't know what I should try next. Reload the operating system completely wipe the file allocation table and make the data unrecoverable? Please notify.

  -darksquare

  Thanks for the help everyone. I was able to restore all my files to the best of my knowledge. Just a quick overview in case others are experiencing a similar problem:

  1 SSD with Win 7 wouldn't start. Message displayed "a disk read error has occurred. Press Ctrl + Alt + Delete to restart» I restarted the machine and went into the BIOS to check that the drive was detected, which it was.

  2. started to Win 7 install DVD and select the repair option. Ran chkdsk on the drive affected with FixMbr and FixBoot, BootRec. I tried to restart after each of these executables, but he led the original disc reads the message. Along the way, the error messages I received were that the System Volume was damaged and Windows cannot recover master file table.

  3 reinstalled Win 7 on a separate startup disk (HDD) and mounted the SSD corrupted as a slave drive. Win 7 brought a dialog box to reformat the SSD drive as the data seem to be unreadable. Has rejected the format option. At this point, I am unable to browse the files on the SSD via Explorer.

  4 pitted some tools part 3 the SSD which indicated that the partition table on the disk doesn't have the hexadecimal value of appropriate endpoint.

  5 Ran chkdsk /r. Finally, some luck. This process lasted several hours and repair the files of nearly 1 million. The reader become navigable via Explorer. The directory on the disk structure has been restored and files (so far I have not found the missing files).

  -darksquare

• Equium A200-1VO - "a disk read error has occurred."

  Hello

  I had my Equium A200-1VO since December 2007 and has never really had any problems with it atall.

  However, last night after a Windows Vista update and restart, my laptop won't start upward. I get a black screen announcing:

  "A disk read error has occurred.

  Please press Ctrl + Alt + Delete to restart»

  I've had no BSOD, and no other suggestion that something was wrong, everything worked perfectly. I checked the HARD drive to see if it had come off his link and reinserted it. But I get the same message.

  I am presented with the only possibility to use the recovery disk, but this means wiping everything out there and start again. I'd rather try to recover my documents before taking radical measures, if it is possible atall.

  If anyone has any suggestions I would be very appreciate.

  Thank you very much

  Mark

  Equium A200-1VO
  -Numtxpackets® Pentiuma® Dual - Core Processor T2310 - genuine Windows® Vista® Home Premium Edition - DVD Super Multi (Double Layer) in car-2 048 (1 024 + 1 024) MB of RAM (667 MHz) - 15.4 "WXGA TFT screen 1 280 x 800

  Hello

  In my view, the error message says a lot: theoretically, your HARD drive may be defective and must be replaced but before that I would test using fitness to drive or another program. Just use Google to find such programs.

  Maybe something was tangled up in your Windows installation. About reinstalling Windows?

  You didn't back up your data to a second drive? I m wondering about this, because the backup should always be made.
  However, if you use an external HARD drive box you can save it on another computer.

  Good luck! :)

• Satellite M40 does not start from hard disk - read error

  "I push the button - briefly see the In Touch with tomorrow TOSHIBA screen - then ' + a disk read error occurred press Ctrl Alt Del to restart +".

  I control alt delete brings me briefly on the screen TOSHIBA where I can choose either F2 or F12.

  Do I need a startup disk and where can I get one in order to boot from the CD ROM?
  Do I try to get into the Satellite M40 product Recovery DVD-ROM - this concern for me as the hard drive will be reformatted and all data will be lost.

  I'm stuck please help!

  Hello!

  If you enter the product recovery disc, Windows will be relocated and will be erasing all data on the HARD drive.

  I think that your HARD drive is damaged. You can check this with the Drive Fitness Test. Here you can download:
  http://www.HitachiGST.com/HDD/support/download.htm#DFT
  Download the CD image, burn it to a CD and boot from it. Then you can test the HARD drive.
  On the same site is a user's guide if you want to know more.

  By the way: you can save the data on the HARD drive, when you put it in a box external HARD disk. Then you can save the data on another PC, if the HARD drive is ok and have no errors.

  Good bye

• disk-read error press ctrl alt del

  I start to load Windows XP Pro and I get an error MSG before it comes to the first Windows XP logo, it reads the disk read error press ctrl, alt, del start I have checked all my connections and cables. I can add another hard drive and use bad like a slave and it starts up fine, and I went to the slave and looked everything I could think of, go back, it just above starts with the same error.

  Hello

  I suggest you get into the Recovery Console and use the where command prompt to run the chkdsk command. This scan the hard drive for bad sectors and recover any information from reading. To get instructions on how to enter the recovery console in Windows XP:
  How to install and use the Recovery Console in Windows XP 
  The KB above also shows how to use the Recovery Console prompt.
  a. Insert the Windows XP startup disk in the floppy drive, or insert the Windows XP CD into the CD drive and restart the computer.
  b. Click to select all the options required to start the computer from the reader, if you are prompted.
  c. when the "Welcome" screen appears, press R to start the Recovery Console.
  d. If you have a computer dual-boot or multiboot, select the installation that you must Access from the Recovery Console.
  e. When you are prompted, type the administrator password. If the administrator password is blank, just press ENTER.
  f. type in the following command and press ENTER:
  Chkdsk /r
  g. once the command is executed type "exit" (without the quotes) to exit the command prompt and check if the problem is resolved.
   
  See also:
  http://support.Microsoft.com/kb/315265
  Note:
  
  Warning of Chkdsk.
  Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost

• kernel data inpage error spaceport sys

  Hey

  I just got a new pc, and whenever I stopped and it starts up again, I get an error: kernel data inpage error spaceport sys

  and the computer just start windows normally.

  What to do / how to fix it?

  Good morning Martine.

  For more information, see the error below:

  -+------------------------------------------------------------------------------------------------------------------

  7 has error checking, {fffff6fc40009b08, ffffffffc0000185, 1 c 2042860, fffff880013617ec}

  GetPointerFromAddress: unable to read from fffff80151b76170
  WARNING: Unable to verify timestamp for win32k.sys
  ERROR: Module load completed but symbols can be loaded for win32k.sys
  Probably caused by: memory_corruption

  Follow-up: memory_corruption
  ---------

  0: kd >! analyze - v
  *******************************************************************************
  *                                                                             *
  * Bugcheck analysis *.
  *                                                                             *
  *******************************************************************************

  KERNEL_DATA_INPAGE_ERROR (7A)
  The requested page of kernel data could not be read in.  Usually caused by
  a bad block in the disk controller or paging file error. See also
  KERNEL_STACK_INPAGE_ERROR.
  If the error status 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
  This means that the disk subsystem has suffered a failure.
  If the status of the error is 0xC000009A, it means the query failed because
  a file system has failed to move forward.
  Arguments:
  Arg1: fffff6fc40009b08, type of lock which took place (1,2,3 or PTE address value)
  Arg2: ffffffffc0000185, error state (state code of e/s normally)
  Arg3: 00000001c 2042860, the current process (virtual address for the lock type 3 or PTE)
  Arg4: fffff880013617ec, virtual address that could not be paged in (or PTE contents if arg1 is a PTE address)

  Debugging information:
  ------------------

  Error_code: (NTSTATUS) 0xc0000185 - peripheral of e/s reported an IO error.

  -+------------------------------------------------------------------------------------------------------------------

  It seems that you have a bad hard drive or RAM module in your new system (ran 6 hollow landfill WinDBG), since it is a new system, I would bring her to the store you bought and let replace it.

  Read this guide on how to test your RAM Modules: http://www.pcadvisor.co.uk/how-to/pc-upgrades/3432631/how-check-for-bad-ram-modules-in-your-pc/

  Read this guide on how to test your hard drive: http://pcsupport.about.com/od/toolsofthetrade/tp/tophddiag.htm

  Personally, I'd suggest to return the computer to the store and allow them to correct the problem, apparently not driver related to me (especially if you updated all..), it seems that you have a malfunction of the equipment.

  You can try and run CHKDISK (http://windows8themes.org/how-to-run-chkdsk-in-windows-8.html), but I suggest you RMA your system and let check the RAM and hard drive.

  If however, you want to ensure that it is not Windows, then reinstall Windows and see if the problems come back, but I bet they will be.

  I know this answer might not be what you want... but...

  Yuri

• PAGINATION OF DATA KERNAL ERROR

  I am facing this error after it crashes. It appears a blue screen and will eventually return to the page of windows 8.

  He said more that KERNAL DATA INPAGE ERROR. Please help me get rid of my laptop. Any help is appreciated!
  I have chrome and an ASUS K55v.
  We need the DMP file because it contains the single record of the sequence of events that led to the accident, what drivers have been loaded, and what has been loaded.

  
  

  WE NEED AT LEAST TWO FILES DMP TO SPOT TRENDS AND TO CONFIRM THE DIAGNOSIS.

  
  

  If you're overclocking (pushing components beyond their design) return you to default at least until the crash is resolved. If you don't know what it is that you're probably not overclocking.

  You may be able to get the DMP files without crashing by booting in SafeMode (F8) with networking.

  If you are overclocking stop.  (chances are that if you are unsure if you are, you are not)

  To allow us to help you with symptoms BSOD on your computer, download the contents of your folder "\Windows\Minidump".

  The procedure:

  * Copy the contents of \Windows\Minidump to another location (temporary) somewhere on your machine.

  * Zip up the copy (compress)

  * Please download to a service like Skydrive or "Rapidshare" to share files and put a link to them in your answer.

  Link to find out how to download below.

  http://www.WikiHow.com/use-SkyDrive

  To ensure the minidumps are enabled:

  * Click Start, in the search box, type: sysdm.cpl, press ENTER.

  * On the Advanced tab, click Startup and recovery... Settings button.

  * Make sure that automatically restart is unchecked.

  * Under the writing debugging information header, select image partial memory (256 KB) in the list box drop-down (varies from 256kb).

  * Ensure to that small Dump Directory is listed as % systemroot%\Minidump.

  * OK your way out.

  * Reboot if changes have been made.

  Please also run MSinfo32 and download the output as well.

  To run MSinfo32 please go to start > run > MSinfo32

  Go to 'file', 'save' and download the PDF is saved with the DMP

  System specs are extremely useful then please include everything you know.

  
  

  Blue screen view and that crashed are often wrong and should only be used in case of emergency...
  
  
  Troubleshooting of Windows/source here
  You can learn more about BSOD here
  You will learn how to test your memory ici 
  An effective question gets help more quick read how here
  Pilot auditor-stalking a GIS behave driver here
  
  
  Co-written by JMH3143
  Team Zigzag3143.com  

• Download of CSV using Browse point (don't get no data found error)

  Hello
  
  I use procedure below to download CSV in my table.
  
  CSV is to have null values in some places ex: 1,.
  2,0.999
  3,
  4,0.696
  
  below the procedure works fine when I am downloading as CSV: 1.0
  2,0.999
  3.0
  4,0.696.
  
  My table is seen as two columns, and I get no data found error when downloading a CSV of null values.
  
  I went through import data in Excel to the database table but no use...
  
  Please help me on this.
  
  Procedure
  ===========
  

  DECLARE
  v_blob_data       BLOB;
  v_blob_len        NUMBER;
  v_position        NUMBER;
  v_raw_chunk       RAW(10000);
  v_char   CHAR(1);
  c_chunk_len  number := 1;
  v_line  VARCHAR2 (32767) := NULL;
  v_data_array  wwv_flow_global.vc_arr2;
  
  BEGIN
  
  -- Read data from wwv_flow_files
  select blob_content into v_blob_data  from wwv_flow_files
   where UPDATED_BY = (select max(UPDATED_BY) from wwv_flow_files where UPDATED_BY = :APP_USER)
  AND id = (select max(id) from wwv_flow_files where updated_by = :APP_USER);
  
  v_blob_len := dbms_lob.getlength(v_blob_data);
  v_position := 1;
   
  -- Read and convert binary to char
  WHILE ( v_position <= v_blob_len ) LOOP
   v_raw_chunk := dbms_lob.substr(v_blob_data,c_chunk_len,v_position);
   v_char :=  chr(hex_to_decimal(rawtohex(v_raw_chunk)));
   v_line := v_line || v_char;
   v_position := v_position + c_chunk_len;
  -- When a whole line is retrieved
   IF v_char = CHR(10) THEN
  -- Convert comma to : to use wwv_flow_utilities
    v_line := substr(v_line, 1, length(v_line)-2);
     v_line := REPLACE (v_line, ',', ':');
  -- Convert each column separated by : into array of data
     v_data_array := wwv_flow_utilities.STRING_to_table (v_line);
  -- Insert data into target table
     EXECUTE IMMEDIATE 'insert into table_name@Schema1 (col1,col2)
      values (:1,:2)'
      USING
        v_data_array(1),
        v_data_array(2);
        
        -- Clear out
     v_line := NULL;
    END IF;
   END LOOP;
  
  END;

  concerning
  Chauvet
  
  Published by: Chaumont on 26 September 2012 10:52
  
  Published by: Chaumont Sep 26, 2012 22:25
  
  Published by: Chaumont on 27 September 2012 01:58

  Chambers,

  You can use wwv_flow_utilities.array_element to avoid any no_data_found. The function does not raise any errors. For example, for the line which only have a value of table when you wait 2, it can be useful.

  EXECUTE IMMEDIATE 'insert into table_name@Schema1 (col1,col2)
      values (:1,:2)'
      USING
        wwv_flow_utilities.array_element(v_data_array,1),
        wwv_flow_utilities.array_element(v_data_array,2);
  

  Kind regards
  Christina

• ODI data loading error checking logic

  Hi, I do not know if it's related to ODI or questioned our command script. We found that loading data ODI errors checking is one record of the other so that as soon as we will have an error in loading batch data (for example, a member is missing), the whole lot turns very slowly due to the error checking process.
  
  Everything we can fine tune the verification of the process of loading data errors ODI?
  
  Thank you!

  Hello

  Have a read here
  It was a bug, but is now resolved.

  Ok?

  See you soon

  John
  http://John-Goodwin.blogspot.com/