Run Dell Datasafe, get message MS_87 the parameter is incorrect.

Similar Questions

• When you try to copy a. DAT in Vista file, get error 0x80070057L, the parameter is incorrect

  I tried to copy a *. DAT file from a CD on my HARD drive. During the last 5 seconds, I always get the following error message:

  Error 0x80070057L the parameter is incorrect

  I am able to open the file, but can not copy. I tried on my laptop (Vista SP1) and on an another desktop running XP and get the same error.

  What causes this problem?

  Hello

  The problem occurs when you try to copy other files?

  Check if you can copy files in Mode without failure.

  Refer to this article for help:
  http://Windows.Microsoft.com/en-CA/Windows7/start-your-computer-in-safe-mode

  Kind regards
  Afzal Taher
  Microsoft technical support engineer

• Error message: & quot; The parameter is incorrect. & quot;

  Whenever I go into the properties for one of my subjects, I get this error message:
  "The parameter is incorrect."
  
  If I change all the properties and click OK, it gives me the message again and does not save my changes.
  Anyone have any ideas?

  Nevermind, I found someone had the same problem. I'm done decomipling my chm file to create a new project. It worked.

• I get a message "the parameter is incorrect" when I try a Windows Media Player security upgrade. What I'm doing.

  I get a message "the parameter is incorrect" whwn I try a Windows Media Player security upgrade. What should I do?

  Hello

  1 have. what security update you tried?
  2. in addition, what version of Windows Media Player you have?

   
   
  Try these steps and check.
  a. Click Start and type cmd in run and press ENTER.
  b. in the type guest following command press ENTER.
  WMP.dll regsvr32.exe.
  c. close the command prompt and start Windows Media Player and check.
   
   
  I hope this helps.
  
   

• Error message: C:\Windows\System32\rstrui.exe "the parameter is incorrect."

  I'm so frustrated!  I tried to download Google Earth, and it would not load - so I started to experiment and I really screwed up the system!  Now, I get error messages saying the C drive is not accessible, and access is denied - trying to make a system restore I ge the message above saying the parameter is incorrect.  When I right click on the c drive, it shows that it is TOTALLY FULL - it wasn't a couple of days! I am running Vista 32 bit.  ANY help you can give me will be GREATLY appreciated!  I use the discussion groups in the office all the time and have always been able to get the right answer - I am hoping that will be the case here, although I do understand that this might be a bit more complicated.

  Thanks for getting back with me!  But I was so freaked out I got back my computer gurus and it costs $100, but it's fixed now!  Yes! If she was my own computer I probably would have continued to try here, but because it belongs to someone else, I didn't take a chance of really of screwing.  It turns out that the C drive was full (in color), and yet he says there's ZERO bites on it!  I wish I could be with my guru to see what he did... but at least I am in place and works now, so it's a GOOD thing! :))) Thanks much to answer and try to help me! Have a great week!

• "The parameter is incorrect" Error Message is displayed on the computer

  I'm running Windows 7 Home Pro on an Asus laptop and recently decided to add my old printer USB, HP Oficejet v40, to our network via a print server, LPR Networking USB wireless home. The Installer seems to fill correctly, and my printer appears in the list of available network printers (I alone). However, when I try to print wireless, I get one or more error messages. The first and the most persistent are: a StartDocPrinter call was not issued. Sometimes (not always) this is accompanied by another popup error: the parameter is incorrect. In each case, the document I am trying to print is no longer in effect. My USB utility Server network sometimes prints, and sometimes it is available. Running the printer troubleshooter cannot correct the problem (s) and always results in the following error: printer HP Officejet V40-P05d0443eb can be contacted via the network. If I connect the printer directly to my laptop, USB port, it prints as expected.

  The print driver is up-to-date. I tried to uninstall and reinstall the printer and print server and have also tried to reset the print server and the router, to anything will do. Any help to fix these problems is greatly appreciated!

  Original title: error: A StartDocPrinter call was not issued.

  Hello

  Thanks for posting your query in Microsoft Community.

   

  You can consult the following articles and check if they help:

  Wireless printing Center Resolution of problems
  http://WWW8.HP.com/us/en/campaigns/wireless-printing-Center/Troubleshooting.html
   
  "The parameter is incorrect" Error Message is displayed on the computer
  http://h10025.www1.HP.com/ewfrf/wc/document?cc=us&LC=en&docName=c03283238

  For the error: "the printer cannot be contacted over the network",
  refer to suggestions provided by Meghmala responded on May 28, 2010.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/printer-cannot-be-contacted-over-the-network-error/a4318308-3D16-44D4-bac8-7fdd10a83208
   
  Hope this solves the problem. If the problem persists, you can write back to us and we will be happy to help you further.

• Try to change the drive letter, but get the error "the parameter is incorrect."

  I am trying to upgrade my PC to run Windows 7 64 - bit on a new Intel Solid State Drive (SSD). I install Windows 7 from scratch on the new SSD (which uses the drive letter J) have just completed and changed the drive letter of my original system from C to M.

  My intention was to reuse the drive letter C to the SSD, but the Win 7 disk management tool will not allow the use of C. "All I get is a' setting is incorrect" error message.

  My first thought was to check the location of the Windows page file. It was indeed using drive J, so I put the pagefile on the D drive instead and restarted my PC.  However, this has not fixed the problem. I always get "the parameter is incorrect" when I try to use the letter C.

  What else could be the cause of this problem?

  David

  I tried a change of the HKEY_LOCAL_MACHINE\SYSTEM\MountedDevices registry but it is just screwed to the top of the new installation of Windows on the SSD (it starts in a unusable mode "is not a real installation"). I was not too concerned by what I had already made my decision to reinstall Windows 7 after making changes in bios to disable all disks except the SSD and force a boot from the installation of Win 7 DVD.

  This relocation is now complete and the new partition on the SSD system has the C drive letter. A reboot with the other shows, active records that the original disc of BONE has been reassigned to the next available drive letter.

  My problem is thus solved. If it was the only way to do so is now a moot point.

  David

• windows\system32\rundll32.exe the parameter is incorrect. Cannoy get access to certain programs and cannot access the "msconfig".

  I get the windows\system32\rundll32.exe error following the parameter is incorrect. I tried a repair Rundll32 loading, but the computer will not accept. All microsoft and windows updates are up-to-date BLAH today. What to do next? When I try to use the box of computer help, a black box appears for about 1 second and the computer does nothing.  Not lock up and I can still do emails, just no game.

  Please run Doug Knox fix .exe (which is not a file .exe so you can run it) and then carefully swipe to the malware.

  http://www.dougknox.com/XP/file_assoc.htm
  http://www.elephantboycomputers.com/page2.html#Removing_Malware

  MS - MVP - Elephant Boy computers - don't panic!

• I can not connect on my user profile who is also the administrator. I get a message that the password is incorrect, however I have not changed the password. s not now what it was

  I can't connect to my user profile who is also the administrator.  I get a message that the password is incorrect, however I have not changed the password. My 11 year old niece used the pc last (play online games) and I was informed that it was a download/installation, but do not now what it was. I can't download or update any information on the pc that this requires the admin password. I am currently using the guest account, that does not give me access to all programs and the pc is running a little slower than ususal. Your help with this questions is appreciated.

  the operating system is Windows Vista Home Basic 32-bit.

  Hello

  If your niece has changed the password, or you have a corrupted system, this Information Microsoft will help you.

  Here are the different circumstances where it can help you.

  You will need to borrow a Microsoft DVD from a friend, Recovery DVD a manufacturer without these special work options available.

  • http://support.Microsoft.com/kb/940765

  If you are unable to connect to Windows 7 or Windows Vista, you can use the Windows Vista System Restore feature, or the Windows 7 system restore feature.

  You may be unable to connect to Windows Vista or Windows 7 in the following scenarios:

  • Scenario 1: You recently set a new password for the protected administrator account. However, you don't remember the password.
  • Scenario 2: You type the correct password. However, Windows Vista or Windows 7 does not accept the password because the system is damaged.
  • Scenario 3: You delete a protected administrator account. Now, you cannot connect to another administrator account.
  • Scenario 4: You change an administrator account protected with a standard user account. Now, you cannot connect to another administrator account.

  And as you say that your niece may have downloaded something, that something could have been malicious, that can cause problems with password.

  Download, updatre and scan your system with Malwarebytes AntiMalware in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  And here's how to go in Safe Mode options; Select safe mode with networking from the list of options:

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  See you soon.

• Error message: the parameter is incorrect, while playing music

  I have WMP 11 for Vista, and recently it stopped working properly for the songs I have. When I go to any folder with a song or a video and try to double click on it nothing happen. then I right click on the song or the video and choose the option "Open with Windows media Player" and an error message is displayed: "/ * the queue name * / the parameter is incorrect"... what should I do about it? I am sure that the problem is with WMP because I have a few other players that work perfectly. Thanks for the attention.

  Media Player problem

  Hello

  You can view these methods:

  Method 1:

  I suggest you to see these steps:
  a. click on start.
  b. click on run.
  c. type this command regsvr32.exe. wmp.dll
  d. press on enter.
  Method 2:
  You can also check:
  Solve the problems of Windows Media Player video and other media or library
  http://support.Microsoft.com/mats/windows_media_player_diagnostic/

• I keep getting messages from the center of Action McAfee Anit-virus, Anti-spyware & firewall disabled, as well as Windows Firewall

  It started after a message popped up on Adobe Reader and I deleted it.  I tried to run applications without success.

  Hello

  Welcome to the Microsoft Community and forums thanks for posting the question. According to the description, you get messages from the center of the Action as McAfee and the Windows Firewall is disabled.

  Please answer a few questions to refine the question.

  1. you remember to make changes to the computer before this problem?
  2. you have more of a security software installed?
   
   
  Anti virus definitions update and check the status

   

   
  Method 1: I suggest you to enable and disable the Security Center
  service in Windows 7:
  a. click the Start button, type services.msc and pressenter.
  b. in the list of Services, right click on Security Center, clickingProperties
  and select disabled.
  c. restart your computer.
  d. once again, follow steps a and b, and then select Automatic (delayed start)
  e. start the Service.
   
   
  Method 2: You can uninstall and reinstall the security software and check.
   
  
  Uninstall or change a program
  http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program

  Method 3:

  Restore the system to an earlier point before installing this application.

  
  http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

  System Restore can return your files system to a point in time before you noticed a problem, without affecting documents, photos, or other personal files. If the system restore does not resolve the problem, you can undo the restore operation and choose a different restore point.

  
  More information on:

  
  System Restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

   

  Hope this information helps. Please reply with the status so that we can help you.

• Message "the parameter is incorrect."

  I have an Officejet 6500 has more all-in-one printer. I am trying to get a read on the ink levels and I get the message "the parameter is incorrect." I rebooted the computer and the printer and I tried various other things and still cannot solve the problem. Help, please

  The next steps would be to reinstall the software:

  If the printer connected via USb make sure to disconnect the cable first.

  Click Start > all programs > HP > model printer and follow the link to uninstall the software.

  Once the uninstall is complete, reboot your PC and reinstall the software.

  You can find the latest version of the software available for sownload to the link below:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-86366-3&cc=us&DLC=en&LC=en&OS=4062&product=4083977&sw_lang=

  Kind regards

  Shlomi

• I try to recover my system using the xp pro installation disc get message that the version on the computer is newer tha the version on the cd

  I try to recover my system using the xp pro installation disc get message that the version on the computer is newer tha the version on the cd

  You have probably updated to SP-1 and SP - 2 maybe since then and the CD is without both.

  You try to restore the system from the cd, or re - install the OS from it?

• Get "error 0 x 80070057: the parameter is Incorrect" when you try to edit the photo details

  I'm changing the date of the photo, and I get this error code, please help me as soon as possible.

  Hello

  The parameter is incorrect error indicates that the files are not accessible when you try to change them.

  Check if the problem continues in a new user account.

  Refer to this article for help:
  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

• Im trying to find my windows oc disk and I keep getting an error shell excute ex failed; Code 87 the parameter is incorrect how can I solve this problem

  Im trying to get my disk of oc windows, and I get an error shell excute ex failed; Code 87 the parameter is incorrect. Please help me

  How can I solve this problem. Thank you.

  Hello

  You did it changes on the computer before the problem started?

  I suggest you perform a startup repair.

  See these articles for help:
  
  http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/how-do-I-fix-a-boot-startup-problem