RV082 access resources on RV016

Similar Questions

• IPSec VPN: connected to the VPN but cannot access resources

  Hello

  I configured a VPN IPSec on two ISP with IP SLA configured, there is a redundancy on the VPN so that if address main is it connect to the VPN backup.

  QUESTIONS

  -Connect to the primary address and I can access resources

  -backup address to connect but can not access resources for example servers

  I want a way to connect to backup and access on my servers resources. Please help look in the config below

  configuration below:

  interface GigabitEthernet0/0

  LAN description

  nameif inside

  security-level 100

  IP 192.168.202.100 255.255.255.0

  !

  interface GigabitEthernet0/1

  Description CONNECTION_TO_DOPC

  nameif outside

  security-level 0

  IP address 2.2.2.2 255.255.255.248

  !

  interface GigabitEthernet0/2

  Description CONNECTION_TO_COBRANET

  nameif backup

  security-level 0

  IP 3.3.3.3 255.255.255.240

  !

  !

  interface Management0/0

  Shutdown

  No nameif

  no level of security

  no ip address

  management only

  !

  boot system Disk0: / asa831 - k8.bin

  boot system Disk0: / asa707 - k8.bin

  passive FTP mode

  clock timezone WAT 1

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  Name-Server 4.2.2.2

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of object obj-200

  192.168.200.0 subnet 255.255.255.0

  Description LAN_200

  network of object obj-202

  192.168.202.0 subnet 255.255.255.0

  Description LAN_202

  network of the NETWORK_OBJ_192.168.30.0_25 object

  subnet 192.168.30.0 255.255.255.128

  network of the RDP_12 object

  Home 192.168.202.12

  Web server description

  service object RDP

  source eq 3389 destination eq 3389 tcp service

  network obj012 object

  Home 192.168.202.12

  the Backup-PAT object network

  192.168.202.0 subnet 255.255.255.0

  NETWORK LAN UBA description

  the DM_INLINE_NETWORK_1 object-group network

  object-network 192.168.200.0 255.255.255.0

  object-network 192.168.202.0 255.255.255.0

  the DM_INLINE_NETWORK_2 object-group network

  network-object object obj-200

  network-object object obj-202

  access-list extended INSIDE_OUT allow ip 192.168.200.0 255.255.255.0 any

  access-list extended INSIDE_OUT allow ip 192.168.202.0 255.255.255.0 any

  OUTSIDE_IN list extended access permit icmp any any idle state

  OUTSIDE_IN list extended access permit tcp any object obj012 eq inactive 3389

  gbnltunnel_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

  standard access list gbnltunnel_splitTunnelAcl allow 192.168.202.0 255.255.255.0

  BACKUP_IN list extended access permit icmp any any idle state

  access extensive list ip 196.216.144.0 encrypt_acl allow 255.255.255.192 192.168.202.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  backup of MTU 1500

  Backup2 MTU 1500

  local pool GBNLVPNPOOL 192.168.30.0 - 192.168.30.100 255.255.255.0 IP mask

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any backup

  ASDM image disk0: / asdm-645 - 206.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) static static source NETWORK_OBJ_192.168.30.0_25 destination DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.30.0_25

  NAT (inside, outside) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_192.168.30.0_25 NETWORK_OBJ_192.168.30.0_25 non-proxy-arp-search of route static destination

  !

  network of object obj-200

  NAT dynamic interface (indoor, outdoor)

  network of object obj-202

  dynamic NAT (all, outside) interface

  network obj012 object

  NAT (inside, outside) interface static service tcp 3389 3389

  the Backup-PAT object network

  dynamic NAT interface (inside, backup)

  !

  NAT source auto after (indoor, outdoor) dynamic one interface

  Access-group interface inside INSIDE_OUT

  Access-group OUTSIDE_IN in interface outside

  Access-group BACKUP_IN in the backup of the interface

  Route outside 0.0.0.0 0.0.0.0 2.2.2.2 1 followed by 100

  Backup route 0.0.0.0 0.0.0.0 3.3.3.3 254

  Timeout xlate 03:00

  Pat-xlate timeout 0:00:30

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  WebVPN

  value of the URL-list GBNL-SERVERS

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  AAA authentication http LOCAL console

  AAA authentication enable LOCAL console

  http server enable 441

  http 192.168.200.0 255.255.255.0 inside

  http 192.168.202.0 255.255.255.0 inside

  http 192.168.2.0 255.255.255.0 inside

  http 192.168.30.0 255.255.255.0 inside

  http 0.0.0.0 0.0.0.0 outdoors

  http 0.0.0.0 0.0.0.0 backup

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  ALS 10 monitor

  type echo protocol ipIcmpEcho 31.13.72.1 interface outside

  NUM-package of 5

  Timeout 3000

  frequency 5

  Annex monitor SLA 10 life never start-time now

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  card crypto IPSec_map 10 corresponds to the address encrypt_acl

  card crypto IPSec_map 10 set peer 196.216.144.1

  card crypto IPSec_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  inside crypto map inside_map interface

  ipsec_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  ipsec_map interface card crypto outside

  gbnltunnel card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  backup of crypto gbnltunnel interface card

  Crypto ca trustpoint ASDM_TrustPoint0

  Terminal registration

  name of the object CN = GBNLVPN.greatbrandsng.com, O = GBNL, C = ng

  Configure CRL

  Crypto ikev1 allow inside

  Crypto ikev1 allow outside

  Crypto ikev1 enable backup

  IKEv1 crypto policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  enable client-implementation to date

  !

  track 10 rtr 100 accessibility

  !

  Track 100 rtr 10 accessibility

  Telnet 192.168.200.0 255.255.255.0 inside

  Telnet 192.168.202.0 255.255.255.0 inside

  Telnet timeout 5

  SSH 192.168.202.0 255.255.255.0 inside

  SSH 192.168.200.0 255.255.255.0 inside

  SSH 0.0.0.0 0.0.0.0 inside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH 0.0.0.0 0.0.0.0 backup

  SSH timeout 30

  SSH group dh-Group1-sha1 key exchange

  Console timeout 0

  management-access inside

  a basic threat threat detection

  threat detection statistics

  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200

  WebVPN

  allow outside

  enable backup

  activate backup2

  internal gbnltunnel group policy

  attributes of the strategy of group gbnltunnel

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  greatbrandsng.com value by default-field

  Group Policy 'Group 2' internal

  type of remote access service

  type tunnel-group gbnltunnel remote access

  tunnel-group gbnltunnel General-attributes

  address GBNLVPNPOOL pool

  Group Policy - by default-gbnltunnel

  gbnltunnel group of tunnel ipsec-attributes

  IKEv1 pre-shared-key *.

  type tunnel-group GBNLSSL remote access

  type tunnel-group GBNL_WEBVPN remote access

  attributes global-tunnel-group GBNL_WEBVPN

  Group Policy - by default-gbnltunnel

  tunnel-group 196.216.144.1 type ipsec-l2l

  IPSec-attributes tunnel-group 196.216.144.1

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  HPM topN enable

  Cryptochecksum:6004bf457c9c0bc1babbdbf1cd8aeba5

  : end

  When you say that "the external interface is downwards using failover techniques" you mean this failover occurred because the ASA is no longer able to reach the 31.13.72.1?  Not that the actual interface is broken?

  If this is the case, then the NATing is your problem.  Since you're using the same VPN pool for VPN connections the ASA cannot distinguish between the two streams of traffic if the external interface is still in place.  The SLA tracking only removes a route in the routing table, but does not affect what happens in the NAT process.

  try to change the NAT statement follows him and the test (don't forget to remove the other statements to exempt of NAT for this traffic during the test):

  NAT (inside,any) static static source NETWORK_OBJ_192.168.30.0_25 destination DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.30.0_25

  If this does not work, I would either turn off the external interface when a failover occurs, or create a second connection profile that contains a separate mass of IP for the VPN connection and ask users to connect using this profile when a failover takes place.  Don't forget to create Nat exempt instructions for this traffic also.

  --

  Please note all useful posts

• To access resources programmatically bundle in the managedBean in MAF

  Hello

  I need to access resources programmatically bundle in the MAF. I tried to go the way of the ADF as:

  Import oracle.javatools.resourcebundle.BundleFactory;

  Private final String RESOURCE_GEN_BUNDLE = "com.oracle.cg.mobile.ViewControllerBundle";

  private = BundleFactory.getBundle of resourceBundle ResourceBundle (this. RESOURCE_GEN_BUNDLE);

  MSG = resourceBundle.getString("viewcontrollerBundle.FACING_NEGERROR");

  System.out.println ("error msg bundle:" + msg);

  Doesn't seem to work survey NoClassDefFoundError Fatal for oracle.javatools.resourcebundle.BundleFactory.

  Can someone tell me the right way to access resources programmatically MAF bundle. Thanks for the help.

  Concerning

  JAI

  Hello.

  Internationalization is a little different in the MAF first, MAF supports beams XLIFF only; You cannot use properties files. Second, the code is very different. You should use the oracle.adfmf.util.BundleFactory class to retrieve the resource group and then use the oracle.adfmf.util.Utility class to retrieve the error message.

  ResourceBundle bundle = BundleFactory.getBundle(XLF_BUNDLE_NAME);
  String message = Utility.getResourceString(bundle, "MY_ERROR_MESSAGE",null);
  

  Best regards

  Frédéric Desbiens

  Senior Product Manager

  Mobility and Cloud oracle

  Twitter: @BlueberryCoder

  blog: http://blogs.oracle.com/blueberry

• RVL200 ssl vpn, I'm not able to access resources network or ping of the Home Office

  I had installed a Linksys router using port forwarding to allow remote access to the server desktop remotely. I had some problems with it and I've always wanted a vpn connection to the office, but I could not ' operate. So I bought the RVL200 after that I read on it and ssl vpn.

  I have the router installed right after the modem cable to the office. I'm able to hit the external ip address of the House. I have the router to access the Server Active directory for connections. The connection works fine, all the different active directory accounts have access to the vpn through this. I am also able to make administration of the router remotely. I am able to connect to the vpn and get connected virtual passage. The icon in the systray says that everything is good. With all this, I'm not able to ping every address on the remote network. I can't reach all the network resources as \\pdrserver\irms or my print server ip address. I can't use network XP Favorites to find anything on the remote network.

  Someone has an idea what I am doing wrong? I appreciate the help.

  I thought about it. I was using the same IP for the home and office. It was confusing. I changed my IP to another system. Home office and now 12.4.4.X now 11.4.4.X. After that, everything worked as it should. Readers without mapped problem, ping remote computers. I could access the remote print servers. Works well. So make sure that you do not use the same IP addresses on both sides of the VPN.

• Linksys RV082, problems of https RV016 router

  Problemas con Cisco Linksys RV082 y RV016, fr pages that manejan https example www.logmein.com al iniciar sesion me dead nuevo has the pagina inicio sesion begins, al encuentro real are una identidad suplantacion posible, por fucnion than tiene el balancear RV carga as cambia UN modem a modem as free mas este otro , esto're uno los problemas con los me sown y aun no he could did en UN buen tiempo, alguien como dress conocera este problemon.

  Gracias of photos.

  Problems with Linksys RV082 and Cisco RV016 in pages that https handshake, for example, when you connect www.logmein.com returns me back to the home page of connection, I find that when investigating a possible identity theft, the RV fucnion is responsible as it changes from one modem to modem another which is freer, it's one of the problems that I have found the balance and I have not been resolved in a while someone will know how to solve this big problem.

  Thanks in advance.

  Enrique,

  On the RV082:

  1. -> Double-WAN management system
  2. Change of balancing load (Auto Mode) at the bottom of the page you will now see binding protocol
  3. Select HTTPS [TCP/443 ~ 443] in the menu drop-down
  4. Select the source IP address or range: (i.e. 192.168.1.100 to 150) that will bind HTTPS for any LAN device that uses an IP address in this range.
  5. Select the address IP of Destination: leave generally to 0.0.0.0 to 0.0.0.0 for all destinations
  6. Select the Interface to bind the Protocol (WAN1 or WAN2)
  7. Check the box enable and add to the list. Save settings at the bottom of page.

  On the RV016:

  1. Management-> multi-WAN system
  2. Look for the setting of the Interface to and select Edit to WAN1.
  3. Follow the steps above.

  Please let us know if this helps or if you need further assistance.

• How do RV082 access secure web sites load balanced mode

  I just bought a gateway/router RV082 Dual WAN because I have both cable and DSL feeds in my office. Everything works fine until I try to access a secure web site or have a conversation through my Vonage internet phone. In failover mode all works. As soon as I select Load Balancing, I have outages. I do not see this listed anywhere as a 'problem' so there must be some kind of workaround if this isn't a bug. Has anyone else seen this and how did you resolve teas?

  Thank you

  Poul

  ^.. ^

  The problem you are having is your doing load balancing and traffic to the secure Web site is to get out the two wan.  The secure site is waiting for a response from the original wan ip, which has established the connection, and then it receives the response from the other wan ip address.  It is a common problem.  You can do protocol binding tab management system and have everything that your https traffic out a single IP wan, this will fix this issue.

• VPN connects but cannot ping or access resources

  I hope this is an easy fix and it's something that I am missing.  I've been looking at this for several hours.

  Scenario:

  I Anyconnect Essentials so I use the SSL connection

  I changed my domain name and external IP in my setup, I write.

  My VPN connection seems to work very well.  In fact, I was able to connect to 3 locations with 3 different external IP address.

  1 location, I get IP address 192.168.30.10, as it should.  I can ping 192.168.1.1, but not the 192.168.1.6 which is my temporary resource, the firewall is disabled on 192.168.1.6.

  2 location, I get an IP of 192.168.30.11, as it should.  I was able to ping 192.168.30.10, could not sue 192.168.1.1 as the place closed.

  Any help would be appreciated, it's getting late so I hope I gave enough details.  I feel so close but yet so far.

  See the ciscoasa # running

  : Saved

  :

  ASA Version 8.2 (1)

  !

  ciscoasa hostname

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 22.22.22.246 255.255.255.252

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  clock timezone CST - 6

  clock to summer time recurring CDT

  DNS lookup field inside

  DNS domain-lookup outside

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  ICMP-type of object-group ALLOWPING

  echo ICMP-object

  ICMP-object has exceeded the time

  response to echo ICMP-object

  Object-ICMP traceroute

  Object-ICMP source-quench

  ICMP-unreachable object

  access-list 10 scope ip allow a whole

  10 extended access-list allow icmp a whole

  pager lines 24

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  mask 192.168.30.10 - 192.168.30.25 255.255.255.0 IP local pool SSLClientPoolNew

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 192.168.1.0 255.255.255.0

  Route outside 0.0.0.0 0.0.0.0 22.22.22.245 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  network-acl 10

  WebVPN

  SVC request no svc default

  AAA authentication LOCAL telnet console

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  Telnet 0.0.0.0 0.0.0.0 inside

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  management-access inside

  dhcpd dns 8.8.8.8

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.5 - 192.168.1.36 inside

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow inside

  allow outside

  AnyConnect essentials

  SVC disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 1 image

  SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 2 image

  enable SVC

  tunnel-group-list activate

  internal SSLClientPolicy group strategy

  attributes of Group Policy SSLClientPolicy

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  field default value mondomaine.fr

  the address value SSLClientPoolNew pools

  WebVPN

  SVC Dungeon-Installer installed

  time to generate a new key of SVC 180

  SVC generate a new method ssl key

  SVC value vpngina modules

  attributes of Group Policy DfltGrpPolicy

  VPN-tunnel-Protocol webvpn

  username test encrypted password privilege 15 xxxxxxxxxxxxxx

  username ljb1 password encrypted xxxxxxxxxxxxxx

  type tunnel-group SSLClientProfile remote access

  attributes global-tunnel-group SSLClientProfile

  Group Policy - by default-SSLClientPolicy

  tunnel-group SSLClientProfile webvpn-attributes

  enable SSLVPNClient group-alias

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  Policy-map global_policy

  class inspection_default

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:ed683c7f1b86066d1d8c4fff6b08c592

  : end

  Patrick,

  'Re missing you the excemption NAT. Please add the following and try again:

  access-list allowed sheep ip 192.168.1.0 255.255.255.0 192.168.30.0 255.255.255.0

  NAT (inside) 0 access-list sheep

  Let us know if you still have problems after that.

  Raga

• VPN Client - connection made but not able to access resources

  Hello

  I have two sites, A Site with a 5510 firewall and Site B with a user with a basic internet connection.

  I need the user to be able to access the PC and the servers here.

  I created a so called remote access VPN and the user can connect to this Site b.

  They get an ip and dns address but no default gateway.

  I am unable to what whether on the network 10.255.0.0/16 ping or access any servers.

  I'll post the config and maybe someone could show me what I'm missing!

  Thanks in advance

  I wouldn't recommend configure the ip pool in the same subnet as your internal network. Please configure a subnet pool a different ip address.

  However, with the current setup, you're absent NAT exemption for these subnets:

  allow inside_nat0_outbound to access extended list ip 10.255.0.0 255.255.0.0 10.255.11.0 255.255.255.0

  Hope that helps.

• How can I access resources on my library of cc of Muse?

  Help-i made all my buttons in illustrator and just put in the library of cc.  Great that I can access it through indesign and photoshop, but how can I access it in Muse?

  The current version of the Muse does not support CC libraries.

  Adobe has demonstrated a version of Muse in development that supports libraries CC (and Responsive Web design) during the Conference from Adobe MAX in early October. This version was announced as scheduled to ship later this year.

• How to access resources in a shared library for a space webcenter Portal

  Dear all,
  
  I packed all my images in a shared library, ADF and I deployed as a shared library in WLS.
  
  Now, I create a custom in my Webcenter spaces appearance. How is it possible to obtain or access these images in my application of webcenter spaces?
  
  This is so that I could use it as a background image.
  
  Advice
  
  Thank you

  It works like PortalWebAssets project in a WebCenter Portal Application.

  If you have a Web content-> images folder, you can access with /images/myimage.png

  Don't forget that your shared library JAR needs to be referenced by weblogic.xml

  Kind regards.

• SWF cannot access resources local file "Data.xml"

  Need help: I built an application allows the user to move one chart to another using a local XML, which I call hollow a HTTPService.
  
  I already found on the net I need to change a compiler argument:-usenetwork = false, but it still doesn't work and I get an error indicating that the SWF is not approved. If someone knows a solution?
  
  Thanks in advance,
  Victor

  Nevermind, I'm a fool. This is supposed to be "- use - network = false '.

• RV016 access to the modem in wan1 administration page, wan 2... from LAN

  Hello

  We have installed router rv016, balancing 5 adsl conections.

  We can access the router rv016 with IP 192.168.1.1 LAN.

  We can access the administration modem1 page in wan1 which has IP 10.0.0.1

  But we cannot access other pages of Directors of modems as fitted wan2 IP 10.0.0.2, or modem wan3 with IP 10.0.0.3, modem wan4 or wan5...

  In the diagnosis of rv016 page, we can make a successful ping 10.0.0.1, but not to another wan...

  All modems have active DHCP ok with access authorization.

  Can you help us?

  Thank you!

  Hello

  Change modems to get LAN IP addresses in different subnets:

  10.0.0.1

  10.0.1.1

  10.0.2.1

  10.0.3.1

  10.0.4.1

  Then, everything should work perfectly.

  Please mark this thread as answer or reply if you have any additional questions.

  -Marty

• Access to resources on the inside and DMZ problem

  Hi Techies,

  I have a pix515 do remoteaccess VPN. People are able successfully to VPN in the box but are not able to access resources on the DMZ or the Interior. DMZ is directly connected to the PIX and inside is behind a CSS.

  Could you people point me in the right direction please.

  Thank you

  Abdul, is solved your problem, have you tried suggested missing statements in your config... Let us know if any questions.

  Concerning

• Problem just started, unable to see area but can be seen on the other PC on the network - can connect to the area but no access to resources.

  Have client with the latest Lenovo laptop, running Windows 7 Pro, part of a Windows 2008 domain. User never had problems earlier but takes off mobile out of office last week that he had then only on vacation. The user has Verizon Wireless for Internet access so that resign. User returned, connected area through the configuration of a connection without error, but was unable to access resources in any domain. No applications have been installed on the laptop so that it is on vacation. In windows Explorer, the user can see as other NAS PC's, printers, other devices on the network and able to access the Internet, but the doman and the server are missing from the list. The connection of the user from another PC to check the profile is ok, the user was able to resources in the domain from another PC. Had a different network user trying to connect on the laptop and had the same problem so I am confident that the problem is with the laptop itself and not domain or server. Also tried to disable the firewall on the computer laptop but did not help, empty DNS and other entries in cache but nothing helped. There were a few normal .net updates on laptop while resign but that was about it. Laptop is running Microsoft's Security Essentials for virus protection.

  Any ideas on how to resolve the additional or possible causes?

  Hi Jack,

  
  The problem you are having is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public.
  Please post your question in the Technet Forum.
  You can follow this link to ask your question:
  Forum TechNet Windows 7:
  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro
  For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• How to access the MDS of Hudson and Machine Unix resources?

  Hello
  How to access the MDS of Hudson and Machine Unix resources?
  
  I can do even Jdeveloper using the local filesystem n oramds Protocol and access resources.
  
  Please share the information for Hudson & Unix Machine?
  
  Kind regards
  En

  Need for resources MDS configure using adf - config.xml in the application. You can also change the configration of 'Oracle_SOA1\bin\ant-sca-package.xml '.

  Concerning

  En