S440 got hot now does not start

Similar Questions

• MacBookPro6, 2 batteries ran down to 2 mos now does not start

  15 "2011 MBP 6.2 running 10.11.3 remained out of order, disconnected for about 2 months. The battery after plugging and shows 5 lights. The MBP now does not start - no edge no screen no effects nothing.

  I have reset the SMC, took out the battery and successor, removed or put around the bars of memory without any effect.

  A bad battery will keep it to start when it is plugged? Is there anything else I should try?

  TIA,

  Bill

  What happens if you leave the battery or disconnected and try to start the machine?

  It happened sometimes with macbook air which complete draining the battery damaged map logical.

  A defective battery should not influence your machine when you hooked it up.

  I recommend you to wear to a bar of genius of apple for validation.

  See you soon!

• Windows Live Movie Maker, used to work, but now does not start

  2 months ago, I used windows live movie director very well. now, I get a message that it does not start and to check my system requirements...  I loaded all updates, check the driver, uninstalled and reinstalled, still does not, any suggestions?

  Have you tried the fix program option in uninstall a program from the control panel.

  Photo Gallery work under voltage is windows? If not,

  Windows Live Photo Gallery is not responding or does not start,

  http://support.Microsoft.com/kb/944221/en-us

• I changed my motherboard and now does not start LR

  I changed my motherboard (PC Win 7) and 6 LR does not start

  I need to download?

  I have to start LR 5 and proceed to 6 LR?

  Thank you!!!

  Franco - Italy

  Hello

  Yes you are right.

  You will need to load it again.

  Please see Download Photoshop Lightroom if necessary.

  Kind regards

  Sheena

• Update the BIOS Alienware x 51 now does not start

  So I have recently reinstalled Windows 7 and a re-install my drivers and using the products download page on another computer Dell drivers and download them to a flash drive and upgrade on the primary computer. I have finished all updates until I got to the BIOS update, I installed in and rebooted my system, now it starts but freezes and does not move to the Alienware Logo. Just to put it out there, I have updated BIOS A08 A14. The screen that I can like normal Alienware Logo screen, showing that I use an Alienware x 51, a bar of blue loading, BIOS Version A14 and then Setup F2 and F12 Boot Options. Any help would be greatly appreciated.

  Thank you

  Zach.

  Hello

  Check in the Bios (for access to the tap water of the F2 key on startup Bios) under the Startup section, look for an option called Boot Mode and make sure that its game in the UEFI. Also, make sure that the Secure Boot option is turned off, save the changes and reboot the system. Let us know how it goes.

• Tablet 2 critical internal battery error 190 now does not start

  Been implemented battery internal criticism 190 on lenovo thinkpad error 2 I bought 2 months ago and now won't start not until after 1 week of charge. Lenovo has a solution.

  Moderator edit: matched the content subject to

  Or anyone in the community has found a solution. Mine is not a problem of cut wire.

  Moderator edit: matched subject to content.

• Factory reset now does not start, doctor No. WebOS available in the profile

  I did a factory reset on my HP Touchpad to give to my son for Christmas. However, I boot the system then select English, then select the country from the United States and the system hangs its been doing this for a few days. I then shut down the system he turned back and did the same thing again and again. I go to my www.palm.com , and log and the WebOS doctor does not appear on my profile. Do anyone know how to install the software on the TouchPad, so I can get that operational back?

  These are .jar files.  Here are the executable java files.  Some browsers have been known to change the .zip extension by mistake.  Try using another browser to d/l the file.

  Go to www.java.com and let the Web site to check your installation to the latest version.

  Make sure that you have the latest java installation on your PC.

  Do you have the great symbol USB before continuing?  You will need the novacom drivers.

  If the process fails, rinse and repeat!  Restart all (you've tried long keys both power and depressed Center on the TP for > 15 seconds, right?), and then try again.

  Good luck, and be patient - I saw the doctor a break of 10-15 minutes before you continue...

  WyreNut

• When my laptop battery died the printer stopped working, now does not start

  The laptop screen went black, (while a print job is in progress) I plugged in and restarted the computer.  Since that time there no task sent to this printer have been achieved. I had to go back to my old HP882C just plugged into the 2side Print Setup and finished work. HP C5580 had a task that will be

  not only cancel all print always not that hell has happened?

  Hello

  I suspect that when the battery is dead, the spooler has been altered.

  Check chan seen message here - one of the highest.

  fixed spooler subsystem app stopped working
  http://social.technet.Microsoft.com/forums/en/itprovistaprinting/thread/460f297a-dd66-4476-A176-542e1519ca3e

  ===================================

  If the above didn't help:

  Use this method to clear the spooler and then uninstall and reinstall your printer (check with the manufacturer for)
  the latest driver).

  Check Mr. Fixits here and if you use the other methods go back and try again later.

  Problems of print and error - a Mr Fixit of printing
  http://support.Microsoft.com/GP/printing_problems

  Solve printer problems - a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/8c11977e-8244-408f-A036-7978a618d7a21033.mspx

  ------------------------------------------------------
  Logon as administrator

  Start - type in the search box-> COMMAND - control to the top of the list and RIGHT CLICK – RUN AS ADMIN

  You can copy and paste each line except those brackets and press ENTER after each.

  net stop Spooler

  (echo suppression of all print jobs)<-- you="" should="" see="" this="">

  ping localhost n 4 > zero

  del/q %SystemRoot%\system32\spool\printers\*.*

  net start Spooler

  (sound Done!)<-- you="" should="" see="" this="">

  ping localhost n 4 > zero

  Another way
  http://4sysops.com/archives/how-to-cancel-a-print-job-that-hangs-under-Windows-Vista-and-XP/

  Check the print - DELETE/STOP queue all jobs - then right click on the printer - REMOVAL
  http://windowshelp.Microsoft.com/Windows/en-us/help/bb6f81d9-4092-4ac8-9716-2bd008f513e11033.mspx

  If you use Control Panel - Classic - printers

  Try after unplugging your printer if necessary.
  -------------------------------------------------------------

  Also check the spooler print and its dependencies and addictions Service.

  Print Spooler service
  http://www.blackviper.com/WinVista/services/Print_Spooler.htm

  How difficulty Windows Vista print spooler starts do not
  http://www.ehow.com/how_4920100_vista-print-spooler-not-starting.html

  ------------------------------------------------------------

  Check this thread if necessary - to stop and erase the spooler

  http://social.answers.Microsoft.com/forums/en-us/vistaperformance/thread/a15779d6-ac0d-42FD-9Ac2-a1da241ea19f/

  and here
  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/58b54fa9-cf6f-40F7-90b2-8093c6777493

  ------------------------------------------------------
  Clean the General corruption and repair or replace the damaged/missing files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  CheckDisk (chkdsk) runs at startup.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------

  Also check with HP support and forums.

  HP support
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  I hope this helps.

• XW4400 does not start. Occurred after the power to the system off for 2 weeks. Now, does not start. Help!

  As noted above in the subject... exploded with power for about 2 weeks supply.  On his return the

  system won't start.  It keeps going in a circle.

  Here's what happens;
  

  (1) it goes to the window HP

  2) immediately goes to a window stating "windows did not start properly. A recent hardware or software change might be the cause. "Then on and other causes.  Well, none of them took place.

  To the bottom of the window there's several options to try.  Safe mode, Safe Mode Networking, last known successful... and start normally.  All the options have been tried several times.  To 30 sec timer waiting for your choice.  NONE OF THE OPTIONS WORK.  Cannot start in any mode.  After all of the selections it shows;

  (3) a flash of the microsoft windows screen and then we go back to number 1.

  Info on the system;

  XW4400

  • Manufacturer part number: ET115AV-CTO
  • Manufacturer: HP
  • Product description: ET115AV-CTO HP xw4400 Workstation computer desk
  • Product type: desktop
  • Form factor: mountable Convertible minitower on rack
  • Operating system: Windows XP Professional 64-bit
  • Processor: Core 2 Duo processor E6700 (2.66 GHz)
  • Front side bus: 1066 MHz front Bus up to
  • Chipset: Intel¿975 X Express
  • Memory: DDR - 2 667 MHz ECC unbuffered
  • Installed memory: 2 GB
  • Maximum memory: up to 8 GB
  • Installed hard drive: 160 GB
  • Hard drives: up to 4 SATA hard drives 2 to maximum
  • Expansion bays: 3 external bays of 5.25 inch and 1 external 3.5 inch bay 2-Bay internal 3.5-inch
  • CD DVD: 16 X DVD + - RW DL
  • Speed variators: controller 4 channels SATA 3 GB s integrated with RAID 0, RAID 1, RAID 0 + 1 capacity
  • Graphics card: NVIDIA Quadro FX1400
  • Expansion slots: graphics PCI Express (x 16) 1 slot 1 PCI Express (x 16 mechanically x 4 electrically) slots 1 PCI Express (x 1) and 3 long legacy PCI
  • Audio: Integrated high definition Audio with Jack Retasking capability,
  • Networking - communication: integrated Broadcom 5755 Netxtreme Gigabit PCIe LAN
  • I/o ports and connectors: front: headphone, microphone, 2 USB 2.0 and 1 optional IEEE 1394 a rear: 5 USB 2.0 1 USB 2.0 (internal) 1 serial port standard 1 keyboard PS-2 port 2 in parallel and mouse audio Gigabit LAN RJ-45 1 built-in audio microphone
  • I have no recovery disks!

  Hello:

  I can't help with your problem, because in this case, my recommendation would be to reinstall the operating system.

  What I can do, is give you information to get a set of recovery discs for your xw4400 for only $10 USD.

  Here's how:

  1. Enter the part number and the serial number on the top of the computer on the Silver label. The model # is a Compaq HP xw4400, but the part number is on this tag silver under the serial No.

  2. call HP at 1-800-952-7689, option 1 (ranking in the list in the option made restore disks).

  3. provide the information asked by the representative who answers the phone. Some simply ask for the serial No., some want at the same time, or they'll want just the serial number and the type of computer (xw4400).

  4. do you have a Master Card or Visa ready for purchase. They do not take discover. You will be charged $10.00.

  You will receive the discs by first class mail, or you can pay an additional $10.00 for shipping FedEx.

  Paul

• Satellite A200 PSAF6A - Vista now does not start

  A200 PSAF6A - 02C01N Vista built-in HARD drive recovery

  My friend used this PC and she just closes without warning.
  Vista won't start now... Turn it on and it starts to load then apparently hangs on a blank black screen just before the Welcome screen.

  I tried to use Linux to access the drive to get its stuff out before you reinstall, but several different versions of Linux can not install Windows.

  I tried the system recovery running now the 0 key during startup, then releasing 0 when the pc started to beep.
  Starts the recovery of loading, then the screen goes blank for a while, then rises... error... F3-F000-0001 error code... Press ok to reboot.
  Press ok, error message will... screen is blank... drive hard HDD light shows work... but it is not closed.

  Tried to launch a drive to reformat Vista. Boots in the disk, loads the files then crashes, just like the original problem, on a white screen.

  Tried the XP disk running... works well until it gets to the part where you choose where you want to install... and said... cannot install on this pc it is no hard drive!

  Tried formatting disk with Gnome Partition Editor... It hangs in the review of the disc.

  I think the next thing to try is to throw the thing out of a tall building and see if it can fly...

  Anyone got any ideas?

  Hello

  HARD drive is recognized correctly in the BIOS settings?
  I think that the HARD disk is dead.

  Please check the last assignment under http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=140926
  Raver post the correct link in his assignment. Try to check the HARD drive.

• Error with product recovery. Now, does not start. Satellite Pro A40

  Hello

  I tried to use my product recovery cd to reinstall windows so that the computer is in "like -new" condition However, when you use a disk and 25% step it crashed on saying me that it couldn't read the disc. Now, when I try to boot, it says ' Please insert system disk and press a key "I do, but I just get the same message repeated. This is if I try to book it from the cd or the hard drive.

  What is my next step, how can I pick up my computer!

  See you soon

  Hmmm it's not easy to say why you t could not complete the installation. For me, it seems that the recovery CD is defective.

  In any case, the message said that no BONES were found on the HARD drive and the laptop cannot start!
  While do I think you should insert an original Windows XP CD and try to boot from the CD. The XP CD should format the HARD drive and install the new OS.

  Sorry, but I put t see another possibility.

• Satellite Pro A100 crashed during Windows BIOS upgrade, now does not start.

  Satellite Pro A100 crashed during the upgrade of the bios from windows (upgrade the bios using windows), now the laptop will not boot. I press the on switch and it gives me just a blank screen, so I think that resets itself. I really need help solving this because I have a University paper due in the next few days and I need my laptop!
  Close for any help.

  It's a scream! :_| : O

  This looks like a damage ROM module!
  How did you do the BIOS update? I have red in this forum that a wrong procedure or wrong BIOS can damage the motherboard.

  I think that it s a deal. I put t know if it s needed to change the entire motherboard or update the BIOS again but I n t think you will be able to do it yourself.

  I think the best way is to ask the Toshiba service partner in your country.
  I think they'll give you more details on the handling of the Fryer

• replaced the hard drive, Illustrator CS4 now does not start

  After that I replaced my Mac (paid by Apple, fortunately) Fusion defective hard disk and restored everything from a Time Machine backup, Illustrator CS4 gives me error 150:30 when I try to run, with instructions to contact Adobe support web site. All I get there are some frequently asked questions and their cat gives suggestions repeated to try the forum. I'm surprised research here do not find other people who have had the same problem. I would have disabled AI CS4 before hand, but the disk failure came quickly and by surprise.

  I've logged into my Adobe account and could see my products, but could not find anywhere to administer anything, like resetting of the authorized computers one can in iTunes.

  Does anyone have a suggestion? I would of course welcome.

  Thank you

  Rick

  Contact support to reset the activations, run the cleanup tool, and reinstall it correctly. There is no magic involved and I'm sure that your own web searches have come up with the same instructions, even if you seem to refuse to recognize them as the correct procedures.

  The Adobe Creative Cloud Cleaner tool allows to solve installation problems

  Download the CS4 products

  Mylenium

• (Redirected) Aurora 4 updated BIOS update now does not start

  Hi all, I just formatted my PC installed fresh Windows 8.1. Downloaded the Aurora Panel and then noticed that there was a Bios Update recommended A3 to A11.

  He told me that I had to switch to A5 first, so I downloaded and it installed fine self. It was then restarted and since then his do nothing.

  No beeps, no display just the fans inside the base unit turning speed hyper and generally strong

  I left for 30 minutes and still made no difference.

  After that, I unplugged everything from the back of the pc. tried again and he still didn't fight with the fans care.

  Scratched inside the base unit and also tried to clear the CMOS and removed the battery and still no boot and load fans

  Is that all you guys you suggest I can do?

  Better in this position in the Alienware owners Club Forum, here:

  http://en.community.Dell.com/Owners-Club/Alienware/default.aspx

  Bev.

• Satellite Pro A200 PSAE4E does not start after upgrading BIOS XP

  Hi, I need help!

  computer laptop, tested just got everything ok with Vista business and everything works fine.
  Now, I have a requirement to test a laptop duel boot XP build and follow the attached instructions to change the BIOS so that I can install XP.

  Restarted the laptop with the bios disk selected bios XP and everything seems ok.
  The phone rings, I answer. When I finished, I think back to the laptop and screen is white.
  Leave it for 20 minutes still white. Stop the laptop and reboot, no tosh start screen, nothing.

  Now does not start, so what do I do to get this thing working again?

  Hey Buddy...

  This looks very bad! :(il ressemble pas à quelque chose a mal tourné àle cours de la procédure de mise à jour dele de BIOS, et donc l'ordinateur portable ne peut pas démarrer correctement.)

  I hope that the ROM module must be flashed again.

  This can be done only by an authorized service provider.
  I see no other solution for contact ASP in your country and ask for help and handling.

  Good luck and best regards