SAS expander backplane directly reduce in SATA mode?

Similar Questions

• Satellite L100 - how do I change the SATA mode in the BIOS options

  Hello world...

  Why is it in the laptop Sat L100 that there is no option in the BIOS-> advanced where in I can change the drive to SATA?
  I saw it in another PC Toshiba laptop

  Hello

  If this option is NOT available in the BIOS, then you will not be able to change that!
  In this case the controller HARD drive will tell in SATA mode and if you want to install an operating system then you need to install the SATA drivers first!

  Good bye

• Satellite L350-172 - slow HDD after set SATA mode for compatible

  SERVUS of Germany

  Yesterday, I bought a Satellite L350-172 and I installed Win XP pro on the HARD drive
  So far so good.
  Driver found on the Web site and so on that I spend in Bios the SATA Mode on "compatible" because the AHCI mode does not work with XP.

  In my view, disk access is slow and windows hang up so that the closing

  Does anyone know how to solve the problem?

  Thank you

  Hello

  It is not unusual that your HARD drive runs slower after the change of mode of AHCI SATA compatible.
  You have disabled the SATA feature and so you cannot use the benefits of SATA.

  And I must say that you are wrong buddy if you say that the AHCI mode does not work with XP.

  You can use the SATA in Win XP, but you must include the SATA driver first.
  Intel Storage Manager contains the SATA driver, and you could include using the nLite software.

  Good bye

• Change the SATA mode in Windows 8

  I'm moving to sata IDE to RAID mode in Windows 8 in order to avoid the re-formatting my hard drive. The solution in Win7 (update registry KEY in regedit does not work). Any advice?

  With all due respect, Srivinvasa Sharath, your answer is very useful.  The question is not ' how can I change the SATA mode in my BIOS?  But, on the contrary, assuming I already know how to change the SATA in my BIOS mode, how Win8 to accept this change and actually start correctly.  There is a guide on how to proceed for Win7, but it doesn't work for Win8.  So we would know what to do differently with Win8 to make it work.

  Here is a link to the article corresponding Win7 so you will see what is asked:

  http://support.Microsoft.com/kb/922976

• WAP54G - MODE CLIENT to Direct TV receiver sat

  Need to connect the receiver of Direct TV Hd to the Internet but the only connection there is wired ethernet (RJ-45 Jack). A WAP54G can be configured to perform this connection through the WRT54G which already works with 2 workstations and a box from Roku WiFi? Not sure if I just duplicated a post. I am new to this.

  Thank you! I bought 2 of them on EBAY - factory refurb @ $18 each in waiting for the response... GOOD answer!

• "authentication control-direction in" CLOSED authentication mode

  Switch: 4510R-E, running a DEV version 3.6.0-based

  ISE: 1.2.0.899 patch 7

  Hi, I worked on a weird issue where some of my clients would pass through their IP address and the only way I could get it back was to spend their open port in authentication mode. I need to run in closed mode, because I change VLAN via MAB.

  I worked with TAC, and they suggested that add the command "authentication control direction in" in my config switchport (below). Couple tests Ive done, this seems to help. But I understand why. Isn't the direction-control a little command reduce to naught the principle of closed mode operation? That is, it allows a communication until the device is allowed. Thank you.

  interface GigabitEthernet2/18
  switchport access vlan 34
  switchport mode access
  switchport voice vlan 66
  events-the link status logging
  authentication event fail following action method
  action of death server authentication of the event allowed vlan 34
  action of death event authentication server allow voice
  living action of the server reset the authentication event
  the host-mode multi-auth authentication
  authentication order mab dot1x
  authentication priority dot1x mab
  Auto control of the port of authentication
  restrict the authentication violation
  MAB
  dot1x EAP authenticator
  dot1x tx-time 10
  service-policy input QoS-entry-policy
  Service-politique-accueil-port-sortie-strategie output QoS
  end

  I also need to use this command to preserve the authenticated devices. He was going on with a video surveillance system, which was an embedded Linux operating system. It's the MAB and because there was no transmission all noisy traffic (unlike a windows box) then the switch would not be able to reauth it as it had no mac address to auth, so show up with an 'unknown' in the MAC field.

  It allows essentially traffic flow out of the port. This active unit to receive HTTP traffic and respond, then the switch could auth it again once the device sent a frame.

  When you do a Show authentication sessions you will notice a Oper control dir: the two will pass to Oper control dir: in

• Satellite Pro A300D - SATA mode disappeared in end update BIOS

  In version 1.9 of the PSAK1E A300D bios there are settings to change the mode of the SATA controller. After updating the BIOS, it disappears. The cell phone was in non-AHCI mode before the update and now it is stuck there. Anyone got the old BIOS at hand (my backup is long gone)? It will completely go AWOL if I downgrade the BIOS version?

  Hey Buddy,

  Have you downloaded the right version of the BIOS of your laptop or another model?

  You should also try to load the default settings in the BIOS (F9).
  Check this box!

  To be hoenst I can t imagine that this option is no longer available on newer BIOS version

• Satellite L350D-10 x - XP installation by using the compatible SATA mode

  Greetings! To me a question. If I can do as a result of the actions.
  (1) compatible SATA to AHCI mode.
  (2) installation XP
  (3) installation driver sata
  (4) restart the system and in the bios change to AHCI compatible

  It will work?
  I do not wish to integrate the drivers separately in win XP.

  Hello

  I think this should functions
  Has anyone here in the forum tried this method and it succeeded.

  Just test and just checking

  It s very interesting

• How to change the SATA mode to AHCI, no setting on the BIOS (Aspire E5 - 471P)

  How to change SATA to AHCI mode. Any setting in the BIOS (Aspire E5-471P-35Y2)

  Are you sure that your system is not already on AHCI?

• Starting USB/change SATA mode. Spectrum of HP Touchsmart XT

  I can't seem to find much information about the Touchsmart HP spectrum XT, so I came here with a few questions.
  How to boot from a USB? How can I change my SATA to AHCI mode?

  You are the very welcome.

  There is no legacy mode option?  There must be.  The legacy mode option must be enabled in order to boot from another device.

  Unfortunately, there is no way to change the BIOS setting.

  I don't understand why HP does not provide these options on their notebooks to consumer, but for some reason any, they have not for years.

  The pilot of the RST is supposed to support TRIM SSD's in RAID mode, if it worries you.

  http://www.AnandTech.com/show/5136/Intel-to-add-trim-support-for-RAID-0

• BlackBerry 10 directly enter the operating mode

  HY all

  Knows anybode here, if I can directly enter the Mode of operation to 10.3 BB? Now, I need to pass manually each time in work mode. Wehen I unlock the phone, I find myself in personal mode. It's not really a lot of work, but not on my nerves...

  aplboy

  Hi @aplboy

  An option to automatically switch to the run mode when the device unlocking is not possible at the moment.

  Since then, it the case, I'll pass along your comments for further review.

  Thank you!

• Computer will directly start in safe mode after installing the drivers

  Hello, I have a Samsung r700 laptop and I reinstalled windows (an accident) of rescue disk-everything, ok, but when I install the multimedia disk drivers samsung they charge (after a long time) and I then asks me to re-boot, then press Finish button. I'm doing this and portable said shutting down and then it seems to try to start. Then I have a grey, but even after 12 hours, screen nothing happens. I then turned off and can only start up in safe mode.

  Any ideas how I can fix it.

  OT:Re - start problem

  Thank you

  Hi Eddie,.

  Thanks for the update.

  Let us know the status of the issue once you install the driver of NVIDIA graphics card.

  I hope this helps!

• I tried to update to service pack 2, the power went out during the reboot, and now my computer goes directly into the startup mode

  Whenever I start my computer, it goes right to the repair/startup mode. Windows Vista. I really need my computer back! ANY HELP! I've tried safe mode, reboot, almost everything I know! :/

  Hello AthanasiusGeorgy,

  Thanks for your post.  Try to contact the manufacturer of your system to see if you can get a recovery for your computer disk.

  See you soon

• Satellite A100: How do I enable SATA NATIVE mode

  Hello, my laptop Satellite A100 PSAA9 and the southbridge is an ICH7M
  I put an SSD in my laptop and the drive controller is locked-> Ultra DMA 6 IDE compatible mode.
  I would switch to the native SATA-1 to increase the bandwidth (from 110 MB/s-150), but I can't find any setting so that, in the last BIOS 6.00

  I think that maybe in the past, Toshiba has enable this feature, but I suppose they might have turned it off for beginners who don't know how to install the SATA drivers during the installation of Windows.

  I found Toshiba BIOS database, but it is locked by a password.
  I'm willing to test any BIOS that could re - enable native SATA mode

  + The message was edited: link has been removed - unauthorized +.

  Hello

  You need the native SATA controller?

  The laptop was equipped with a controller SATA interface supports the Serial ATA Rev. 1. 0a.

  Some laptop models take a BIOS that contains a SATA mode option.
  This option can be changed on AHCI or in compatibility mode.

  But as far as I know a100 BIOS does not contain these settings

• Satellite A100-237 / PSAA9 - how to enable AHCI (SATA Native mode)?

  Hello

  I have the Satellite A100 - 237 (PSAA9) and I would like to activate the AHCI (SATA Native mode). But in the BIOS there is no settings as AHCI or SATA mode.

  Is it possible to enable it in any other way (hidden fixing, utility sw)? Or only new special BIOS for this update (I have the latest 5.90) can solve this problem?

  Thank you for the answers.

  No response for the last 5 days. Of course, there is no special hidden parameter or BIOS. ;)

  As far as I know that there is no hidden settings and also no special BIOS. If something like that exists perhaps for technicians and non-public use.