WAP54G - MODE CLIENT to Direct TV receiver sat

Similar Questions

• SAS expander backplane directly reduce in SATA mode?

  I have a C6220 II with an Expander backplane of 2.5 ". However, I don't need performance of fast storage in this machine and want to use the PCI slot for something else, so I thought to remove the RAID controller and attach directly to the controller of the motherboard, which takes only supported SATA. My drives are SATA, rather than SAS, but I understand that this will not work because the controller should support SAS to use the Extender.

  I was wondering if it is possible to change a setting, perhaps a rider, to allow backplane running in SATA mode directly, rather than as an Expander, so that I can use the direct connection of motherboard? I only need two drives from the node, then I don't need to use the expander control.

  Thank you.

  Tentonin,

  There are no jumpers to move for this, you need to replace backplane with version 2.5 live Backplane part # WC17M (below)

  That will allow you to connect directly 24 SAS/SATA ports to 24 2.5 "SATA/SAS drives. Because it is a passive basket background, it does not support the flexible allocation of hard drives at the nodes; each node in the chassis will get an equal share.

  Let me know if it helps.

• Receive MSN APPCRASH. EXE trying to you connect to MSN Premium. Started in safe mode, tried to reinstall, but received the same information.

  Receive MSN APPCRASH. EXE trying to you connect to MSN Premium. Started in safe mode, tried to reinstall, but received the same information. Restore the computer to a problem earlier from the same date.

  original title: APPCRASH MSN. EXE

  Hello

  As you have already tried to reinstall the program, I would say that get you in touch with MSN support for help on the issue.

  MSN support

  https://support.MSN.com/default.aspx?WA=wsignin1.0&St=1&wfxredirect=1

• Pwerconnect 6224: vlan client computers do not receive the ip address of DHCP server on a different VLAN

  Hello

  I have a prolem routing dhcp requests between the vlan management where DHCP server resides and the other VLANs.

  I have the scenario of base with three VLANS: vlan 10 (management vlan), 20, 30, configured on a Powerconnect 6224 switch L2 mode. This switch is connected to a pfsense router. The router is configured at the package of road between the VLANS and it does it well.

  In Vlan 10, I have a configured DHCP server to use the ip addresses of all the VLANS (10, 20, 30). VLAN 10 client computers receive ip address but not others from other VLANs.

  When I put the ip address in the appropriate range of VLANs manually on computers, I ping the server and I have connectivity.

  This suggests that the problem is with the dhcp package.

  The following is the configuration of the switch:

  Configure
  database of VLAN
  VLAN 10,20,30
  VLAN 1 1 routing
  VLAN 20 2 routing
  VLAN 30 3 routing
  output
  SNTP server time.nist.gov
  clock timezone 1 minutes 0
  battery
  1 1 member
  2 2 Member
  output
  DHCP IP address
  IP address vlan 10
  name of the IP-server 172.16.10.1

  bootpdhcprelay cidridoptmode
  interface vlan 1
  Routing
  IP 172.16.1.1 255.255.255.0
  output
  interface vlan 20
  Routing
  address 172.16.20.1 IP 255.255.255.0
  output
  interface vlan 30
  Routing
  IP 172.16.30.1 255.255.255.0
  output
  level of 20fc49459a1898b923ed3ec7b3e81276 user name 'admin' password encrypted 15
  No spanning tree
  spanning tree priority 0
  l2relay DHCP
  DHCP l2relay VLANs 10, 20-30
  DHCP l2relay circuit-id VLANs 10, 20-30
  !
  interface ethernet 1/g2

  l2relay DHCP
  switchport access vlan 20
  output
  !
  interface ethernet 1/g3
  l2relay DHCP
  switchport access vlan 30
  output
  !
  interface ethernet 1/g21
  switchport access vlan 10
  output
  !
  interface ethernet 1/g22
  switchport access vlan 10
  output
  !
  interface ethernet 1/g23
  switchport access vlan 10
  output
  !

  interface ethernet 1/g24
  switchport mode trunk
  switchport trunk allowed vlan add 10,20,30
  output
  Server SNMP community EyesOfNetwork ro
  SNMP-server community public ro
  output

  I followed the instructions in the powerconnect 6224 user guide, but no progress on this issue.

  Any help will be be grateful.

  Thank you

  Zoubeir

  The DHCP server stores information that could be useful? May need to configure monitoring ports and something as wireshark to monitor DHCP packets. This would help determine where the package is stopping.

  example:

  Console (config) #monitor session 1 source interface 1/g8

  Console (config) #monitor session 1 destination interface 1/g10

  session mode 1 #monitor console (config)

  right now I don't see anything in the config of the switch that stands out. If the DHCP server is configured for option 82, then you will need to include the following command on the switch.

  Example:

  Trust l2relay console #dhcp (config-if-1/g1)

  But I don't think that's our scenario here.

• direct mail "receiver" a jammed

  When I try to receive my "live mail" I get the signal that there mail but just, it sticks and does not spread. Help, please. Bez2

  Bez2

  If you are referring to Windows live mail (a mail client) reconstruction that should contribute to the application

  If you currently have problems using Windows Live Mail, please try to fix it by following these steps:

  Type "Wlarp" into the search (without quotes of course), and then press enter > fix all programs WLE

• Registration of client-sample-app Push received the error 403

  Hi guys.

  I work the pusk sdk demo.  When I run the client Simulator demo.

  first register the URL of content provider. I got a 200 response code. It is successfully

  then register at https://pushapi.eval.blackberry.com. this time, I got a 403 responsecode

  and the text of the response is

  Http: 403 error,
  "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd" > ""
  http://www.w3.org/1999/xhtml"lang ="fr"XML: lang ="fr">
  
  

• Unterschied zwischen Vlan VTP Mode Client und Server

  Hello colleagues,

  habe viel im Internet search must aber keine richtig verstandliche Anleitung found.

  Kann mir einer verständlich imagine was the server mode exactly der Unterschied rumwuseln VTP Client und ist, danke im vorraus.

  Bitte nach keinen link opportunity!

  Hallo,

  Though gar nicht ICH, dass are gained von CSC auch ein deutsches Forum gibt - therefore sharp sehr PSAT Antwort kommt.

  Unterschied der ist, dass im Server-Mode Lavaggio der VLAN information, welche via VTP gained der Domane Gables werden, sind possible:

  • Upload eines neuen VLAN
  • Löschen eines be VLAN
  • Umbenennen eines be VLAN
  • Ein bestehendes VLAN in 'suspended' status set den, usw.

  Auf einem VTP Client sind sharp Lavaggio nicht allows - und der Unterschied ist das Schön auch.

  Jede der oben mentioned Lavaggio führt dazu, dass die Configuration revision betting wird; differentiate und die receivers VTP-Nachrichten von dieser observes, dass are aktuellere als die lokal gibt shipping information. Welchen Mode Sender und receivers solcher Nachrichten haben, spielt keine Rolle - entscheidend ist immer nur die Configuration revision training. Kann so for instance ein customer einen Server al, wenn die Configuration revision seiner VTP-Nachrichten high ist als die servers. DAS wird erfahrungsgemass in Bezug auf often missverstanden Server/Client Mode.

  Gruss

  Rolf

• How test mode Stage3D material directly in Flash CS6 ctrl + enter?

  Hello

  Render mode during the test Flash CS6 Ctrl + Enter mode FP launched with the software. How to change automatically to hardware instead?

  esdebon, I don't know for this option.

  I mean something else.

  (1) setting it Direct mode

  (2) write the init code and ask context3d with info pilot during extraction

  3) press ctrl + enter and you will see that the RenderMode there SOFTWARE.

  As I undestand - authplay.dll you see after pressing ctrl + enter do not have hardware rendering mode. Only software. When you publish to swf is working very well in swf. But not in the test drive

• Without SSL or SVC - Tunnel Mode client?

  Hello

  I have a really quick question. When you enable SSL VPN should I choose between SSL without client or Client SSL VPN. IE, the portal with (CIFS, Telnet, Citrix) or the complete network SSL access client.

  It seems that it is one of the other of this doc, but I thought it would be nice to have the SSL VPN client with the ability to click on a link for full network access.

  Any ideas?

  Here is the document that I've referenced.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00806ea271.shtml

  Best regards

  JB

  You can have without client only, client + anyconnect (click on the link on the portal without client anyconnect) or anyconnect only. It all depends on how you configure the group policy on the ASA.

  Kind regards

  Roman

• How to configure Gemfire mode client/server with external supplier of XA transactions

  Hello

  I would like to have a transaction between the operations of Gemfire and WebSphere MQ using Atomikos as XA transaction manager.

  The documentation is rather evasive about how to configure Gemfire with an external transaction manager when using a client/server Gemfire deployment.

  Any help appreciated.

  Thank you!

  Unfortunately the Atomikos is not supported. Please see this thread for more information: GemFire and Atomikos in tcServer

  -Jens

• Just upgraded to 45.5.0 and all you Bird says that it connects to the server, nothing happens. Restarted in safe mode but still do not receive the messages.

  Is it possible to restore the previous version? If so, how?

  Hi Zenos. No he did not imply outlook.com or hotmail. However, it seems not be related to a setting in Norton Internet Security. Fiddling in any case that seems to have solved the problem. Thank you.

• SATA HDD mode & performance on Satellite P100-222

  Hello everyone!

  I found that my HARD drive in instead of ATA7 UDMA5 mode supported. It looks like SATA ACHI is disabled in the BIOS, and I find no way to turn it on. It is clear that even faster UDMA5 then the drive HARD, but what about NCQ & other SATA command supported?
  In any case, the HD tune results http://www.hdtune.com is less than that specified for this HARD drive & interface:

  HD Tune: TOSHIBA MK1234GSX Benchmark

  Minimum transfer rate: 7.7 MB/s
  Transfer rate maximum: 34.4 MB/s
  Average transfer rate: 28.6 MB/sec
  Access time: 17,0 ms
  Gust speed: 64.2 MB/sec
  CPU usage: 9.1%

  Now the slowest part of my system & waiting to start to the top or level of loading takes a long time.
  Is someone have any suggestions to increase the performance of the HARD drive?

  Hello

  In my view the problem is not just HARD disk performance you need to optimize your operating system. How long takes the boot process depends on the application from Windows OS list. You can check it out if you go to start > run and enter MSCONFIG here.

  When the system configuration utility is started Startup tab check and remove the check mark in front of elements, you need not. Also, check the startup folder and delete all the shortcuts, you don't need. On this way, the boot process should be faster.

  If you need more performance for games I recommend you to upgrade RAM. You will see that the unit runs a lot faster and you can use several applications at the same time.

• RRI and Client Mode

  Hello

  I'm reading the "Cisco VPN Config complete Guide" by Richard Deal and without a doubt it's a good book. I am confronted with a difficulty to understand something here.

  In my opinion, reverse road Injection is more useful in the Mode of Extension of LAN in Client mode, because the connections must be made from the company to the SOHO network network. And to do this, the corporate network must know the SOHO network. IPP is used in this case, install a static route inside the company and then VPN gateway redistribute it in the corporate network.

  In client mode, the reverse is true: connections are initiated from the client software or the SOHO network to the corporate network ONLY. So why do I care all to reach the SOHO network or client software from the company network? The author does not specify that.  That's what the author said:

  "The Cisco IPP provides the best approach to remote access clients. IPP is a further development of Cisco-owners for IPsec. At the end of ISAKMP/IKE Phase 1, the remote access client does the following:

  • If in client mode, the client is assigned an internal address of the gateway VPN; the VPN gateway this will add as a static route to the local routing table.  ---- > WHY?

  • If in network extension mode, the client sends the network number of the Interior of the interface of the VPN gateway using an ISAKMP/IKE Phase 1 message. "---> MAKE SENSE

  Please clarify why should I the IPP solution for the client mode. IPP for mode LAN Extension makes more sense.

  Kind regards

  AM

  Hello

  As I mentioned in the first answer,

  Consider a situation where you have a central office VPN device that IS NOT the device that crosses all traffic internal to the external network. In other words in your internal network the default route redirects traffic to another device, for example the perimeter firewall.

  Now for all traffic to flow between the 2 different networks you must naturally the routing tables on the device between the networks to have a route to each network or traffic not correctly between them.

  So consider a situation where your hardware client Mode Client connects to the central VPN device (which is not the gateway for all external traffic) which is running OSPF with all internal routers and the IPP is NOT used. The IP of PAT address used by the hardware Client Mode Client is never adverticed to the rest of the network and traffic flows incorrectly for the perimeter firewall to which the default route points to. If IPP has been activated (and other settings) internal routers could properly bringing traffic back to the PAT IP address to the VPN device rather than the perimeter firewall.

  Naturally, the situation described above applies to a LAN Extender mode also, but in this case the VPN device is naturally adverticing a whole network/subnet instead of an IP address of the host used as IP address of the PAT customer.

  If the remote Client Mode or LAN Extension Mode hardware Client connects to the central site, the central site must have a route to the remote network or the IP of PAT address for traffic to flow between the 2 end points of the network.

  If the central VPN device does not install a route to the address IP of PAT to the central network and then naturally the traffic won't be a way. Customer address IP PAT mode traffic will reach the central site, but the return to the address IP of PAT traffic will not flow properly without IPP.

  -Jouni

• Error FRM-92050 by trying to open the form after the passage in HTTP mode

  Hi all
  
  Yesterday, I installed Oracle Applications 11i on Red Hat Enterprise Linux ES 4 and forms work properly in default mode, which is a native (socket). Following steps 4 and 5 in [Doc 201340.1| https://metalink2.oracle.com/metalink/plsql/f?p=130:14:6398415066875997204:p14_database_id, p14_docid, p14_show_header, p14_show_help, p14_black_frame, p14_font:NOT, 201340.1, 1, 1, 1, helvetica], I enabled the HTTP mode and now my forms do not work. When I opened a form now, I get this error:
  
  FRM-92050: unable to connect to server: / forms/formservlet:-1
  
  Details...
  Java exception:
  java.io.IOException: negative content-length of http://...
  ...
  
  I searched the forums for this error and all the results that I found the deal with HTTP headers or cookies being corrupt, usually by an intermediate network device and MetaLink (web proxy, cache Accelerator, web SSL, etc.). I do not use anything of the kind - the client connects directly to the Oracle server.
  
  I checked the Apache error log, and that's what I see:
  
  [Game may 14 09:10:28 2009] [error] [10.11.1.114] clients denied by server configuration: / work/oracle/viscomn/java/java
  [Game may 14 09:10:28 2009] [error] [10.11.1.114] clients denied by server configuration: / work/oracle/viscomn/java/java
  [Game may 14 09:10:33 2009] [error] [client 10.11.1.114] File does not exist: /work/oracle/viscomn/java/oracle/forms/icons/oracle_logo_light.gif
  [Game may 14 09:10:33 2009] [error] [client 10.11.1.114] File does not exist: /work/oracle/viscomn/java/oracle/forms/icons/oracle_logo_light.gif
  [Game may 14 09:10:34 2009] [error] [client 10.11.1.114] File does not exist: / work/oracle/viscomn/portal/VIS_gen1-cs49/forms/formservlet
  [Game may 14 09:10:34 2009] [error] [10.11.1.114] clients denied by server configuration: / work/oracle/viscomn/java/oracle/ewt
  [Game may 14 09:10:34 2009] [error] [10.11.1.114] clients denied by server configuration: / work/oracle/viscomn/java/oracle/ewt
  [Game may 14 09:10:34 2009] [error] [client 10.11.1.114] File does not exist: /work/oracle/viscomn/java/oracle/ewt/alert/resource/AlertBundle_en_US.properties
  
  I don't like the look of these messages "client denied by server configuration." What's also weird is that the two files referenced by these messages do not exist on the file system:
  
  [oracle@gen1-cs49 log] $ cat/work/oracle/viscomn/java/java
  Cat: / work/oracle/viscomn/java/java: no such file or directory
  [oracle@gen1-cs49 log] $ cat/work/oracle/viscomn/java/oracle/ewt
  Cat: / work/oracle/viscomn/java/oracle/ewt: no such file or directory
  
  Any ideas? Are there any other logfiles that I need to check?

  Kyle,

  Routine & ROUTINE tried to start internal competitor Manager. The ICM is already running. Contact you system administrator for more than assistance.afpdlrq received an unsuccessful outcome of PL/SQL procedure or function FND_DCP. Request_Session_Lock.
  Systematic FND_DCP. REQUEST_SESSION_LOCK received a result code of 1 of the call for DBMS_LOCK. Request.
  DBMS_LOCK possible. Request resultCall failed in establish_icm
  Internal competitor Manager has encountered an error.

  Follow these steps:

  -Stop application services
  -Stop the database
  -Start the database
  -Start the application services and the simultaneous mananger
  -Check the condition of the simultaneous Manager

  Kind regards
  Hussein

• Is it possible to directly connect dish Qosmio G20?

  HY everybody,

  I have a Qosmio G20-PQG21. The receiver is 60 metres from the position of the laptop. In this case, the channel is not editable. The problem that this person wants to change channels. The problem is quite simple... can I connect the coaxial cable from the dish directly to tv tunner and setup guide? or do you have another solution for my situation?

  Thanks in advance

  Hello

  In my opinion it of not possible connect the cable satellite directly the Qosmio.
  You are also unable to connect the TV directly with the satellite dish. It of the same case on the laptop. You need a receiver sat between the laptop and the flat sat.

  There are two possibilities:
  1.), you buy a longer cable from the satellite dish to the receiver and place the receiver closer to the laptop.
  2.), you place the laptop more near the sat receiver ;)