HP G71 Notebook PC: problem changing BIOS
Hello
I just posted a question about having 4 GB of memory and the computer showing only 1 GB of physical memory.
I saw through a post that someone recommended to go into the bios Setup and check a box and type 4096.
The computer then rebooted and I had problems since.
I need to be able to come back in my bios and change the setting to the value of the original.
How do I do that?
Thank you
Bud
Hello @budhines,
Thank you for visiting the HP Forums! A place where you can find solutions for your problems, with the help of the community!
I stumbled upon your post on the laptop and wanted to help you! I looked in your question about your HP g71 Notebook and questions with a BIOS error. I recommend to restore the default BIOS settings. You could restore the BIOS withthis document by selecting the reload the default BIOS settings.
I hope this helps.
Thank you.
Tags: Notebooks
Similar Questions
-
HP G71 Notebook PC: Memory for laptop
Hello
I have a HP G71 Notebook PC. I have 4 GB installed, but shows available at 984 MB physical memory?
It is a wonderful phone but seems a little slow. I've added memory some time ago and decided to check my information memory and was surprised to see that even if I installed 4 GB of memory, and the system shows that it is aware of this, the system memory is only say that I have less than 1 GB of memory available.
I would like to upload a screenshot of my information system, but I see no image upload button.
How can I get the laptop to enjoy other 3 GB of memory?
I saw in another post it was expandable to 8 GB?
In this post, they had a HP G71 EOU.
Wow he must break down. You shouldn't have to change anything on the memory in the BIOS, so I don't know what you were doing it there. The F10 is a restoration of the system, so if you went into that you might have erased the hard disk or at least it does not boot. I really don't think we need to put the memory problem side I think that may be the root of all your problems. Uninstall what you added and material back to the origin let's at least we know will work. But please forge not come unattended or you can see where it gets you.
-
Pavilion dv6 Notebook PC - problem with the installation of ubuntu
Hello
I have HP Pavilion dv6 Notebook PC.
BIOS ver. Hewlett-Packard F.17, 02/06/2010
X 86-based PC
Operating system: Win7 Home PremiumI tried to install the ubuntu 5.04 version but it shows error "Kernel Panic"
I tried several times but is unable to come up with solutions.
Please help me... its urgent...
Thank you very much for the reply!
The information provided by you is very useful...This problem can be solved by putting the flash drive for installing and using a more recent version of linux...
-
Problem changing channels in Windows 7 Media Center
My Windows XP Media Center 2005 machine had a hard drive crash, and so I just replaced with a Windows 7 machine, also with a TV tuner.
Old set up has worked perfectly, blaster/transmitter infrared has been able to control the cable box - Scientific Atlanta Explorer 2200 to Comcast.
Set up the new machine, also with the IR Blaster. New machine can change the channel correctly in 'Live TV'. It works by pressing a channel upward / channel down, or entering the channel number.
But when machine is trying to change the channel to start a new record, or jump off the Media Center Guide, it shows that the first digit, and then displays the cable box '? "and does not change the channel. So I think it's something that the decoder does not correctly or correctly, interpret or Windows has problems, change the signal.
I have experimented with different requirements of speed of IR and whether or not he must enter/OK but have not been able to make it work.
Thoughts of what he must try or change then?
Thanks for any help.
Update on my original post. I "think" I have success. I am now able to change the channel using the guide and the system can change the channel while recording in the background.
I went from the Scientific American cable on a 'Digital Transport adapter"box that Comcast sent me. The manufacturer of the box is listed as "Made in China for Technicolor", and is the model number: DCI105COM1. The box is extremely
For the settings, I had to use: 3 digits, enter the channel number and the speed of the middle.
Let's give it a few weeks and see how it works and if there are differences in quality.
-
BlackBerry 10 I bought the second BBQ10, have problem change BBID
I purchased BBQ10 from a friend and I have a problem changing the user ID. myfriend even forgotten the password and email address has already been disabled. what I would do.
Hi @john_KSA119
Let us know if the provided @John_Clark KB help!
Roughly speaking, simply perform a security wipe of the device that will restore the default settings
In other words, when the wipe is complete the device you can set the camera like yours, like its brand new.
I didn't add, you should tell your friend that whenever they give a device they should always remove personal data first by precautionary measure
-
Problems of BIOS X100e with device Gobi 2000 WWAN
Hello
I have problems with BIOS versions newer than the 1. 10A of output.
As soon as I apply the two new versions 1.11 (6XET32WW) and 1.13 (6XET34WW), the device WWAN that Gobi 2000 is not listed in the Device Manager and a connection using this device is not possible more.
The most recent logins indicates that the device is not found.
Apply default configuration settings after the update of the BIOS is not the problem.
Internet research shows that many people are struggling with this problem.
As soon as I roll back to the 1. 10A (6XET31WW), version of the BIOS, the problem no longer exists.
System details:
* Thinkpad model: 2876 - 27G
* brand new thinkpad/thinkvantage packages installed
* currently available updates windows update installed
* BIOS work: 1 10A (6XET31WW)
* Causing problem BIOS: 1.11 (6XET32WW) and 1.13 (6XET34WW)
Kind regards
rotorhead
-
PROBLEM changing the value of a variable in my scene movieclip
Hello
I have a problem changing the value of a variable in my scene movieclip. I explain: I combobox on my stage containing the categories, and in the scene that I load an xml file containing links to php files that work with the combobox control.
On the stage I have a movieclip "camera roll" inside this movieclip on the first image I have a php script file selected in the scene of loading. I use a function with a variable load() "theUrl" inside like this: T.load (theUrl);
In my scene, I want to change the value of "theUrl" within the film of movieClip. I tried filmstrip.theUrl = url; But it does not workthe xml file <?xml version="1.0" encoding="ISO-8859-1"?> <slideshow> <area title1="10 Last updated" link1="link1.php"/> <area title1="special" link1="link2.php"/> </slideshow>
Here is the code on my stage:
var link1:Array = new Array(); var LINK:String; var url:String; var whoOn:Number; whoOn=0; var x:XML = new XML(); x.ignoreWhite = true; x.onLoad = function(success) { var photos:Array = this.firstChild.childNodes; for (i=0; i<photos.length; i++) { _root.link1.push(photos[i].attributes.link1); } url=link1[whoOn]; filmstrip.theUrl=url;//<<--HERE }; x.load("category.xml"); var cbListener:Object = new Object(); cbListener.change = function(event_obj:Object) { trace(select.selectedItem.label); if (select.selectedItem.label == "Last updated") { whoOn=0; } else if (select.selectedItem.label == "Special") { whoOn=1; } url=link1[whoOn]; filmstrip.theUrl=url; //<<-----HERE }; select.addEventListener("change",cbListener);
Here is the code inside the clip "film".
var T:XML = new XML(); T.ignoreWhite = true; T.onLoad = function(xml) { etc etc etc } T.load(theUrl); //<<---HERE it still undefined
the code on the timeline of the film should be placed in a function() (or better, move all your code to the main timeline). but, if you leave the code on the timeline of the film strip, call the function that contains this code whenever the url changes.
-
Notebook G71 won to boot after BIOS update on HP site
I just updated the BIOS on my notebook G71... I downloaded the update from the HP site and it has been updated V20 to V23.
After the update, the system became an automatic restart and now it does not move before the initial startup screen that shows HP and "ESC to return to the Start Menu" logo at the bottom. I tried the ESC key, but nothing past then is except that it says "esc... pause start." Nothing anyway. Now I can't reboot my system and it is dead. Help, please. Steve
Unplug the power cord, remove the battery, hold the power button for a total of 30 seconds, connect AC only, see if it will load windows now.
-
CANNOT CONTROL THE SCROLLING. CURSOR DOWN TO THE LOW WHAT MAKES IMPOSSIBLE TO SAVE TO A FOLDER
Hi @STICKMAN5124,
Nice day! Thank you for your participation in the Forums of HP Support! It is a great location to get resolutions and interact with experts from the community. It will be a pleasure to help you.
I saw the post and understand that after only a bios updated cursor drops down due to a problem of scrolling.
Impressive work, do the update of the bios. Kudos to you for this. It is a privilege to work with tech-savvy and technically competent customers like you and we greatly appreciate your business with HP. You have been great to work with.
Please check in F2 diagnostics if the scrollbar works correctly. If Yes, then you can update the chipset drivers and http://hp.com/drivers touchpad drivers you can also consult with a mouse external further isolate the issue.
You can also run diagnostics on the touchpad from this link by going to the UEFI F2 diagnostics: http://support.hp.com/in-en/document/c03467259 please run the complete components. If any component fails, please note the failure code. This is done to determine if the problem is hardware or software partners.
If it passes and scrolling works very well, please perform these updates. If you are still having the same problem on page F2 UEFI (screen) then you could roll back bios after performing a hard reset. Link for the hard reset: http://support.hp.com/us-en/document/c01684768
- Please perform this step to roll back bios. Hold down the "Windows" key and the letter "B" at the same time, then press the power also button for about 5 seconds at the same time.
I hope this helps. I would like to know how this happens. I hope the problem is solved without hassle and the unit works very well.
Just to say thank youPlease click the ' Thumbs Up ' button to give a Kudos to appreciate my efforts to help me. If it helps, Please mark this "accepted Solution" because it will help many other people with the same problem to get it resolved without hassle.
Now carefully and have a wonderful week ahead.
-
I tried to boot from my USB Acronis boot device to clone my C: drive to another HARD drive, but I was unable to set the boot order (first USB) because it keeps resetting & put the USB back where it was before. I've done this before without problem; I wanted to boot from an external USB Acronis rescue disk & run the procedure to clone of it. The USB is listed in the startup as list "Sandisk Cruzer 1.27 & it's the ISO boot Acronis on this file but I failed to get the pc to boot from it.» (not this time in any case). After a needless frustration 3 hours I ran successfully clone of C: drive procedure. I checked the clone by disconnecting the source & boot from it, but it works "BOOT PXE ON IPV4 followed by PXE BOOT ON IPV6 before it starts the clone. The startup disk is listed before the lines of IPV in the bios then why what is happening? I disabled the 2 procedures of IPV with F5 & now it starts normally, but I do not consider this problem solved, because I have not yet able to boot from USB & I don't know why I had to disable these 2 lines.
Addendum: I revisited the right bios & reactivated 2 disabled lines & it is now booting properly, no nonsense IPV. Go figure.
Help!
Hello
I've seen similar problems before. I solved me my clearing the CMOS and then start with only a UEFI (the main HD) compatible device. After that the problem had gone away, I reconnected it and then my other active UEFI device.
-
Problem HP BIOS change sequence, won't be in the USB first.
Model: 120-1132
64 bit
I press 'ESC' after the reboot, go into the BIOS, "Computer Configuration", I am faced with UEFI and its submenu and legacy and its menu.
Legacy, I chose the USB hard drive to the top of the legacy section. It is said, to enter = dragged that allows me to get back into the legacy. I press "F10" to accept.
Then I go to 'File' to accept the changes and exit. When I restart the PC, it ignores the Flash drive and continues on the BONE. I went on it with
My tech team Comcast GIS support more... looked at the Web site for the steps, but the boot sequence will not follow the sequence of Boot USB I
It has changed and continues to go to the BONE. Tech also checked with the drivers to see if she needed an update, the amount of the fine too.
Hello
The issue seems to be with the material. I suggest you to ask your question on the HP Forum. The HP Forum support link is mentioned below:
http://h30434.www3.HP.com/T5/desktop-hardware/BD-p/HardwareDPC
-
HP ENVY 17-j184na Notebook PC: problems of wireless connection on the new laptop
I bought a new laptop a few days ago and tried to connect to the network without wire in our apartment for 2 days but nothing helped.
So far, I did the following steps:
-Restore the system to factory settings.
-Powercycled the network.
-Reset the TCP / IP / catalog Winsock.
-Checked and changed the stop option.
-Re-installed and updated all the drivers of network.
-Started in SafeMode w / networking and still unable to connect.
-Ran all 3 windows solve problems and the problem of internet connection of HP.
-Updated the BIOS with the latest version of the driver.
I created my own personal hotspot using my phone and managed to connect very well, so I think that maybe that's a problem with my laptop to connect to my router, but everything else connects very well.
I have an ethernet cable connected and has associated with perfectly too.
My laptop is a HP ENVY 17-j184na Notebook PC and my wifi specifications are
Manufacturer: Broadcom
Description: Broadcom BCM4352HMB 802.11ac adapter Wi - Fi 2 x 2
Driver version: 6.30.223.221
Physical address: 40-E2-30-BF-F0-0DModems are involved as much as I have the following (my apologies in advance, don't know how it's called technically, but it's the same one as in the photo):
http://www.broadbandchoices.co.UK/guides/hardware/sky-broadband-routersI don't know if that helps, but also sometimes the connection does not appear in my list of connections, but it is very rarely, about 3 - 4 times in the last 2 days.
If anyone could offer advice that could help I would really appreciate it and if someone needs additional information then please let me know (and possibly let me know how I could get this information).
Thank you in advance for anything
Hi all
Problem has been resolved.
Just in case someone else has the same problem, if you try to connect to a router and it communicates but don't connect does not then it might be a problem with the frequency to which you are trying to connect.
In this case, my laptop could connect only to a 5 GHz frequency but my router was capable of a frequency of 2.4 ghz, so he was able to connect to all the rest but not that. (Particularly if you use a hub SKY).
The problem has now been resolved by buying a wireless adapter card that plugs into the USB port. If you don't need to buy a Please make sure that buy you one with dual band capabilities.
I hope this helps someone in the future!
Best regards
-
NB305-442BL - problem with BIOS
Hello friends
What happens is that while the mother this screenshot blue machine and since that has begun since I did a BIOS update, it comes to update the BIOS for NB305 netbooks, but it seems I'm wrong on the model already I noticed that the machine was a 442BL, may be able to correct for the machine for me BIOS no problem , or there will be a form any of the decommissioning of the BIOS of the machine to which I had before giving problems, greetings
Post edited by: Fercheins
Hello
First the NB305-442BL is not known to me, I googled for this model number and cannot find a template containing this serial number. What NB305-xxx you have exactly?
Secondly, I think that the BIOS is not the problem here. Generally it should be impossible to upgrade the BIOS if you want to use the version of the BIOS is not compatible.
Usually, you should get a message saying that the BIOS is not compatible during the updating procedure and the update procedure should be cancel automatically.In your case, I recommend the BIOS to default settings. Access the BIOS by pressing F2 for the BIOS settings. Here, press F9 for default settings, and then save changes F10 before you exit the BIOS.
In addition, the BSOD can be caused by software problems. Perhaps the system is confused to have you tried a fresh install of OS to make sure that the BSOD isn t caused by the failure of the system? Would be worth a check.
-
HP Pavilion g7-2345sf Notebook: keyboard problem
Hello
The keyboard of my laptop blocked a press any key. For example, if on Firefox, I click on the address bar, I can see the cursor moved to the left. It is the same behavior on all programs. To stop this behavior, I have to push on several key hazardly. This shutdown behavior or the laptop respond as if another key block.
I tried already to:
-restore the original BIOS setting > > Ditto
-change the keyboard > > Ditto
-disconnect the keyboard > > Ditto
Thanks in advance for your help.
Problem solved by forcing the bios flash with the key combination: power + Windows + b
-
Decommissioning of CPU on Tecra A8 - how change BIOS and fan work?
I recently downgraded the processor in a Tecra A8 of a T7200 at a T2300 and the fan is now at full speed all the time. I am aware that I need to change the bios somehow to tell him that he is now using a different processor, does anyone know how to do this? If it requires a specific program, please provide a link, or let me know the name and I'm going to find a copy.
Please don't give me the answer of stock that changing a processor is not possible. It + is + possible, although I understand that Toshiba would much rather have buy me a new laptop at home while they did intentionally what should be an exchange of relatively simple equipment to a real problem. There is really no good reason for why these laptops bios cannot adjust their profiles automatically cooling for the whole class of processors socket M.
The TDP of a T2300 is 2 degrees lower than that of a T7200 so the cooling system of the laptop must face easily, infact it is A8 models out there that originally shipped with a T2300. All that I want to be able to do is swap processor with another compatible processor without the machine going mental, it's too much to ask of a piece (originally) quite expensive Kit.
PS. Toshiba actually read and post on these forums or is it just fans?
I assume you want to read what says Toshiba on Exchange of CPU in general:
http://APS2.toshiba-tro.de/KB0/TSB9401AX0001R01.htmYou are right. I also switched the CPU on my old Satellite M70.
In any case, the document of Toshiba wrote:
+.... It is unclear if the new processor is compatible to the system board. Integrated chipsets can take charge of their technical specifications a wide range of processors, but this does not mean that all types of CPU can be used in a mobile system, since cooling integrated systems have been designed individually for each series model to ensure the optimal operation of the machine... +.
Maybe you are looking for
-
The pencil of Apple requires a port light to recharge. Does anyone know a USB male to female adapter port lighteners that would load the pencil on one device other than the iPad?
-
11.4 iTunes on Mac not recognizing iPhone 4S more
Hello. It's my first post here, so really, really hoping that someone can help me! My 2 year old somehow managed to make a hard reset of my iPhone and all that he deleted accordingly. Went to do a backup on my Mac iTunes restore as I always do, howev
-
Aspire x 3950 - after windows 10 upgrade dvd/cd drivers missing
After upgrade windows 10 cd/dvd drivers disappeared. Microsoft technicians have worked on this for 4 days could not find the problem. Can't argue with acer because the product is not under warranty. Any suggestions?
-
My toolbars were disabled, how do I activate them?
I had about five toolbars from various locations. They have been disabled by my son. Now I have none. I would like to activate the main toolbar of windows 7. Could someone please tell me how?
-
Basic tips to keep your printer running longer.
Everyone whats to get the most for their money, but many people do not know or realize, that you have to put in a little effort to keep things smooth. Just as if you want your car to last for 1 million miles, you need to do regular maintenance. If