Satellita C660-13 q PSC0QE - problems identify the correct driver

Similar Questions

• Satellite C660 - how to install Windows on the new drive?

  I have an old C660 of 14 months (2 months warranty!) and the HARD drive died quite suddenly.

  * 3 days works great
  * 2 days, got stuck at the "starting Windows".
  * Tried to fix with a System Repair (DVD) boot disk, but could not solve the problem (ran all night)
  * Start of DVD today and now the prompt of commands, each command "dir" on c: takes 20 seconds and try to copy files gives IO error.

  I'm going to buy a new HARD drive and install, but is there a way to get Windows 7 on the drive?
  There is no Windows disk supplied with the notebook... THERE is a recovery partition, but it died too.

  I don't want to buy a new copy of Windows when I already have a license.

  (I never have a backup complete incl. system, like the one and the only time that I tried to do that it was unable to complete the process, killing of many Virgin DVD-R in the process).
  I have most of my personal files backed up.

  Thank you

  The situation is quite clear. You don t have created the recovery disk and you have only two options now:
  (1) you can order the original Toshiba Recovery disk and install the original recovery image
  (2) you can get the original installation disc from Microsoft and install own OS

  In the first case, check it please http://aps2.toshiba-tro.de/kb0/TSB0202TA0000R01.htm

  If you take the decision to use option 2 Please note that your product key is useless and you have to pay for the new activation of license and the code. The sticker product key Microsoft belongs to the recovery image only.

  If you have any other questions you are welcome.

• Satellite C660 is unable to start for the first time

  I have a Satellite C660 - PSC0AQ-03C019 + 1B194392K

  For the last year laptop worked fine in the last 2 months, however he had a problem starting. The first starting attempt of the day, it does not start, it is consumed on gets in front of splash screens after the cursor flashing in the top left then hold with a blank screen (not the cursor just a low glow).

  Hold down the power button / turn off and turn on again then the computer will start. sometimes (not always), it will ask to start normally or repair.

  The laptop works perfectly in use does not fall out of mistakes. Restarting the laptop works as expected close and turn on/off after 5 minutes works great.

  If the laptop is left for an hour or more, it starts the same as above. turn off and turn on/off the system will start but with boot normally the question.

  He has not indicated in the error logs files

  I did a full reinstall of HARD drive recovery system.
  I did a full system reinstall from recovery DVDs.
  I did a full system reinstall from DVD disk a hard new recovery.
  I replaced the ram

  I tried to update the bios, but get an error
  BIOS version more than 200
  Battery capacity over 10%
  AC is attached

  Hello

  The description of your problem is, for me, quite confusing, and I do not understand your problem.
  Can your notebook load and start the preinstalled operating system or not?

  Enter the BIOS and set it to default settings. After that restart your laptop and to describe what is happening exactly.

• My Satellite C660-155 won't boot to the top

  My laptop Toshiba Satellite C660-155 won't boot to the top. When I turn it on, I get a flashing "-" at the top left, then the screen goes black and nothing happens after that. It's more than a year, which means he went from his guarantee.

  It happened already, about 4-6 weeks, a friend fixed but it is now back to the black screen.
  Any advice would be greatly appreciated.

  For better understanding, you must offer more specific information.
  You can enter boot options using F8 at startup?
  Figure option fix my computer in the list?
  You can boot OS in safe mode?

  Did you create the recovery disk?

• Satellite Pro A120: I have problems with the installation of the graphics driver for W2k

  I installed windows 2000 on an A120, the system is fully packed and service updated before I even start to install the necessary drivers, I am unable to restart the system. I once, install as recommended drivers that I have problems with the graphics driver because it will not be installed because it requires a reboot and then I can't install new programs that require a restart that the driver has not been installed correctly.

  The laptop is a Pro A120, age of 1 week and came with XP home, because of this toshiba will not offer me support I changed the o/s even though they obviously support 2000 on this laptop, because they provide the drivers.

  Any ideas would be greatly appreciated.

  Hello

  Did you use and install the drivers from the Toshiba driver page right?
  The drivers of Toshiba W2k for Satellite Pro A120 have been published and are ready!

  But please pay attention to the Toshiba drivers.
  There are two different sets of Satellite Pro A120, with different drivers W2k!
  After choosing the good laptop and download the drivers please follow the proper installation order that is indicated in the document "installation instructions"! Check it!

  I think that if you follow this guide line everything works and runs correctly. Good luck

• Satellite M30 - problem with the graphics driver and Quicktime movies

  I just installed a 40 GB to 80 GB hard drive and installed all the drivers in the correct order, as indicated by toshiba. Everything works well except the used for Quicktime .mov files. All I get is audio but no image - other than a colorful blur screen!

  I think I've isolated the problem to the graphics driver. Whenever I turned off / uninstall the driver dedicated for the graphics card FX 5200 GP (version 4.6.44) Quicktime files work fine. It is only when I installed the dedicated driver problems occur!

  Can someone tell me why this might be?

  Hello

  Do you use the graphics driver from the Toshiba driver page?

  Try to use the QuickTime Alternative 1.77. In this version the codex QuickTime has been updated.
  This version uses these features:

  -Media Player Classic [version 6.4.9.0 + SVN build 2006-12-24]
  -Codecs QuickTime [version 7.1.3.100]
  -QuickTime plugin for Internet Explorer
  -QuickTime plugin for Opera/Mozilla/Netscape
  -Extra plugins for QuickTime
  -QuickTime DirectShow parser
  -Wrapper DirectShow QuickTime decoder
  -CoreAVC 0.0.0.4
  -CoreAAC 1.2.0.575

  check it out...

• Satellite L20-214 - isolate bad sectors on the HARD drive?

  Dear Sir

  My laptop fell off my table leading to serious hard drive problems. The hard drive now has some bad sectors that can be repaired with the chkdsk command. I managed to get my data on an external hard drive. Despite the bad sectors, I can reinstall it however from the recovery cd. Starting after that time consuming (1.5 hours) and after starting Windows I get the error messages from programs that cannot be started. It's the same thing after each reinstall. My guess is that the recovery disk writes data on the same spot every time both on bad sectors.

  I was wondering if theres a way to fix or even isolate bad sectors on the disk, so I can continue to use my laptop.

  Your help is very appreciated.

  Hello

  You can try HDD Regenerator 1.61 (HDD Regenerator is a unique program for regeneration of physically damaged hard disk drives. It does not hide bad sectors, it really restores them).
  However, the best way is to buy a new hard drive :)

• Satellite C670-11 q clicking loud noise the HARD drive

  Hello!

  I helped my neighbor to find a new laptop and the entire installation and start-up.

  We ordered a C670-11 q and it works very well, theres just a nuisance.
  The drive made strong rattling noises, not as a dying or working drive. It's the same sound when you turn a disc, just a lot stronger. I guess that's the "arm of disc" that goes into its safe position.

  I don't know if this laptop has a shock sensor to do this? The laptop was flat on the table, and there where NO vibrations while she does. There are no clicks under load, but they occur randomly when walking to the idle or surf/write normal.

  I checked also save energy options and disabled to turn the disk, without help.
  Also, this seemed odd, because the clicks occur often several times in a row. But there is no doubt it more when running on the battery.

  I am running the BIOS and latest drivers in the area of support (as of yesterday).
  The disk is configured in performance mode, I'm testing battery economy - should I?

  And no, the drive took a beating. I was the first person to turn it on.

  The drive is Hitachi, I don't run their analysis - no error.

  Any help is greatly appreciated: o)

  > The drive makes some noises clicking on, not as a dying drive or work. It's the same sound when you turn a disc, just a lot stronger. I guess that's the "arm of disc" that goes into its safe position.

  One of my computer portable HARD drive makes such noise too.

  I m not exactly why, but I also think that it is at the head of discs moving record position.

  However, I think that this is not really a malfunction since the laptop works pretty well and I didn't notice any problems with the HARD drive or files but I have created a backup of my files, just to be sure that you know
  I think you should save the date just to be sure

• Satellite L300-01:00 PSLBGE - cannot install the graphics driver

  Hello everyone.

  I have a big problem with my laptop video driver.
  Yesterday, I started my windows and put Windows Vista on it.
  I got all the drivers from the toshiba site but ran into a problem with the graphics driver.

  When get it Setup starts and them it gives me an error "this computer does not meet the minimum requirements for installing the software. The Setup will exit. I must say that before the start, I also got Vista and it worked.

  So can you please help me because I don't know what to do to...
  I tried all the possibilities

  Thank you very much

  Teodora

  Hello

  You can try to install the graphics driver in Device Manager.
  Go to the Device Manager, choose graphics card, click on update driver, then point to the (ini files) graphics driver files stored on the HARD disk and complete the installation

  Try this usually it should help

• problems affecting the correct size of fonts

  I have problems affecting the correct size of the font in mail and print, how do I return the policy to the original settings?

  Hello
  • What mail client do you use?
   
  It depends on what email client / browser you are using.
  Each browser / email client must have the print properties which should allow the user to adjust the print size.

  If you use IE, check the zoom settings. Do follow link below:

  http://www.Microsoft.com/enable/training/windowsvista/webzoom.aspx

• "A problem with the display driver.

  Recently, I get an error message whenever I open Photoshop CS4. It reads as follows.

  "As Photoshop has encountered a problem with the display driver and has temporarily disabled GPU enhancements. Visit the Web site of the manufacturer of the video card for the latest version of the software.

  "GPU improvements can be enabled in the Performance preferences panel."

  I checked the graphics cards in Device Manager, and when I tried to update the software, it told me that I was aware.

  • OS: Vista Edition Home Premium
  • Dell Inspiron 1520
  • Display driver: NVIDIA GeForce 8400 M GS

  Sincerely, Danny

  Hello

  Try to update your display manually driver and do not use the analysis of the drivers on the manufacturer's website either.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system. For
  each driver in the list, additional useful information is displayed: load address of the driver, description,.
  version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - Device Manager - Display Adapter - note the brand and complete model of your
  video card - double - tab of the driver - write version information. Now click on UPdate Driver (this
  cannot do anything as MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
  This will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party with their
  own the software and drivers and all other main drivers that you have.

  Now go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration) and then of the manufacturer of the device
  (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for the BIOS, Chipset and software)
  updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after each installation.

  Always check in the Device Manager - tab drivers version you install actually shows up. This
  because some restore drivers before the most recent is installed (particularly that audio drivers) so install a
  pilot - reboot - check that it is installed and repeat if necessary.

  Repeat to the manufacturers - BTW on device at the DO NOT RUN THEIR SCANNER - manually check by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
  This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
  questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
  manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.

• After the clean install of windows 7, it gives an error saying that there is a problem in the hard drive.

  * Original title: hard drive

  I have a lenovo laptop, processor Intel i3, 500 GB hard drive. After the clean install of windows 7, it gives an error saying that there is a problem in the hard drive. I ran chkdsk looking for bad sector and its display 6000 KB in bad sectors. After completing the audit when it began to restart its stuck when the windows logo appears. What should I do? Reinstall the windows help?

  Run the hard drive HD diagnosis extended CD scan manufacturer to know with certainty the State of the reader.  If your brand has no bootable diagnostics in the link, use Seagate Seatools burned onto CD or SeaTools for a USB key .  Follow this with a full check disk command from the installation media kicked prompt know with absolute certainty the State of the reader.  If he repeated the errors after you run the two tests twice, I replace it or at least keep everything backed up in real time.

  If by chance the drive past diagnosis then compares the steps you've done with the best possible Clean install Windows 10 in the link, you can do more if it varied too - especially if the partitions were not deleted during install.  If you do then I additonally run own Diskpart command command line of the punt media accessible to the first screen after startup by pressing SHIFT + F10 keys, or through the repair your computer on the second screen.

• Error "Windows has encountered a problem installing the software driver for your device." Windows found driver software for your device but encountered an error trying to install it.

  So I got a wireless mouse for my first time and it won't even install on my computer. It isn't the mouse because I tried other wireless mice and none of them work. In my device under other devices Manager there are only 2 USB receivers listed with question marks next to them. It is said that they can not find the drivers for the device. Then under my HIDDEN I tried to update the HID-compliant device and the USB input device, nor able to update. This is the message I get.  Windows encountered a problem installing the software driver for your device. Windows found driver software for your device but encountered an error trying to install it. Peripheral HID-compliant, the system cannot find the specified file. I already contacted EVGA about the issue, because there is where I got my motherboard, but they said to contact Microsoft and I didn't really want to pay 50 dollars to send them an email. That's all just ridiculous.

  Well, I found the solution, just in case anyone has the same problem.  Apparently some day caused Wireless does not work on several computers. So you go into Manager for all of these research and device drivers manually. Then, you look for in C/windows/winsxs. Then the wireless mouse/keyboard should work.

• my computer asks me to fix a problem with the graphics driver intel but windows tells me solution can not be downloaded

  computer crashed and rebooted itself. I first started in safe mode, and the computer did not find any problems but had sent a report anyway.

  To restart normally, the center of the action (or as I would say, Center!; - p), has been asking me to scan with windows defender and a problem with the graphic driver intel. Scanned well, but to solve the problem, said action solution Center could not be downloaded. I am most definitely connected to the internet and have tried to solve this question many times during approximately the last 18hours?
  Help would be much appreciated?

  Good suggestion but I tried this, had to go the manufacturer of the laptop, but still no luck. Think he was playing tricks on me in any case, as seemed to be resolved with a full audit of the system and diagnosis.

  Thanks for the effort though...

• I get the message: Photoshop has encountered a problem with the display driver and has temporarily disabled GPU enhancements. Visit the Web site of the manufacturer of the video card for the latest version of the software.

  Photoshop has been giving me the warning:

  Photoshop has encountered a problem with the display driver and has temporarily disabled GPU enhancements. Visit the Web site of the manufacturer of the video card for the latest version of the software.

  Also other programs are affected.  I suspect a recent download of Adobe.  Can anyone HELP.

  No, it has nothing to do with updates of Adobe. There is a problem with your video card driver.

  Go directly to the Web site of the manufacturer of the GPU for updates (not Microsoft, not a System Builder).