Satellite - 14G - L855 devices are not detected in the Device Manager

Similar Questions

• My installed products are not appearing in the extensions Manager

  Help, my installed products are not appearing in the extensions Manager. See the image

  

  If I understand correctly, the 2015 versions don't support the extensions more and each update manager to the new version of the provider, or install them manually. Also, this applies to own or download Adobe extensions from the market!

• Satellite L40 - no HARD drive not detected in the BIOS

  Hello

  I need some advice here. I have a Toshiba Satellite a colleague here, type L40 - 14N. She wanted to run the Toshiba Recovery CD procedure to get back original configuration... system was going way too slow and all that, no other problems. Anyway, she's not very experienced and one way or another the recovery failed.

  Problem is that the system does not detect a HARD drive now more for some reason any. Not in the BIOS, not during the procedure of Toshiba Recovery CD if I start it now. I also tried a Vista installer retail and loaded drivers SATA raid as mentioned on this forum. Without success, no HARD drive detected.

  It's weird, because nothing essentially. Any suggestions how I could solve this problem and get the HARD drive online?

  If the HARD drive is not detected, the installation of recovery will not work and also a Microsoft installation disc.
  The HARD drive should be detected in the BIOS, otherwise that an installation is not possible.

  However, it seems that the HARD drive is defective because the BIOS peut t detect it.
  If your laptop is in warranty got a local ASP or you change the HARD drive by yourself.

• inter esxi host ipv6 multicast traffic are not detected by the destination VM

  Hello

  Warning, I do not have in-depth knowledge of vmware, so please excuse the bad wording, misconception and ignorance in the post below.

  The current topology is:

  

  Each esxi 4.1 update 3 (DL380 G8) host is to connect both layer 2 switch.

  on each host, the vswitch has two network cards configured as active/active, with the default NIC cluster approach (route based on the original virtual port code).

  Everything else is default.

  The switches are connected by a link to trunk (not bunk)

  I have two Windows Server 2008 R2 VM in the same subnet and you have enabled ipv6 on them (by default)

  When two virtual machines are on the same physical host, ping-6 destination_ipv6_address works (I just use the link local address)

  When two virtual machines are on different hosts, ping fails with the "destination unreachable" message, which usually means the neighbor discovery process fails (similar to arp in ipv4 where source VM cannot get mac address of the destination virtual machine)

  When two virtual machines are on the same physical host, the the packet capture shows that Neighbor Solicitation message is sent via an ipv6 multicast address

  When they are not on the same physical hosts, packet capture on the VM shows that the destination virtual machine will ever get the destination ipv6 multicast packets.

  I then connect two DL380 G8 in a similar way to the switches and install windows Server2008 R2 directly without virtualization on them and ping-6 works perfectly.

  My questions are:

  -I missed somewhere, a configuration to allow ipv6 multicast to work? Or even to remove any 'logic' and treat it simply as a show?

  On network switches, you can do this by disabling IGMP who will then deal with multicast as broadcast packets.

  Although I can't find a similar setting under esxi anywhere.

  -J' saw an option "Enable ipv6" on esxi, but I guess it's only useful if the host itself to participate in ipv6 and therefore not applicable to my case?

  The only similar question I found the research is on the link below, which suggest to hardcode the next table on virtual machines, which is not ideal.

  I can confirm however, hard coding the table nearby on two virtual machines to work. This problem seems to be on how esxi vswitches manage ipv6 multicast traffic

  ESX4 and multicast

  Ideas, points of view are very appreciated

  Ed

  I don't know if this will really solve your problem, but it is worth trying to update the firmware of the NETWORK adapter and the driver.

  Looks like it's a HP NC 331FLR NIC (gen8 DL by default NETWORK 4 ports with the BCM5719 chip card).

  There is no binary updates that you can run from the 4.1, but you can update all the components of the firmware with the current Service Pack HP for Proliant image:

  HP Service Pack for ProLiant

  Or start the server in a live Linux of your choice and use the Linux binary update:

  http://www.HP.com/swpublishing/MTX-ec0e18db6a8e4d978b57aa95d1

  These will update the NIC 331FLR to the Boot Code version 1.37/NCSI 1.2.37.

  Then update the tg3 driver in ESXi with this set to 3.129d.v40.1 offline:

  https://my.VMware.com/group/VMware/details?downloadGroup=DT-ESXI4X-Broadcom-TG3-3129DV401&ProductID=136

  You need the file bundle offline (BCM - tg3 - 3.129d.v40.1 - offline_bundle - 1033618.zip) in this package. You can import in the vCenter update manager for easier deployment or install it (probably) ESXi shell with esxupdate--bundle=/tmp/BCM-tg3-3.129d.v40.1-offline_bundle-1033618.zip

  I'm a little rusty in the Department of ESXi 4.1 CLI however, you may need to use the vihostupdate utility or with PowerCLI Install-VMHostPatch remote:

  https://pubs.VMware.com/vSphere-4-ESX-vCenter/index.jsp?topic=/com.VMware.vSphere.upgrade.doc_41/esx_upgrade/patches_updates/t_host_upgrade_using_vihostupdate_esxi.html

• Hosts are not displayed in the laboratory Manager

  I have an instance of Lab Manager 4.02. It works fine, until recently, I had to remove hosts from the instance of LM. While everything was closed, and the hosts were removed carefully, I added the new guests, ensuring you configs were identical, networks etc. Same version and everything. The virtual Center took the boxes, and they work fine.

  Lab Manager will, however, not seen. I confirmed repeatedly that none of my services fail, and no newspaper display errors. But the hosts under laboratory Manager section is empty.

  I checked with wireshark, and I get connectivity, as well as the responses of the Director of the lab - virtual Center.

  I brought the former hosts, with the same effect. I did then the labmanager to other VC instance he had never been associated, and he wouldn't see hosts there either.

  What would cause this? Someone at - he already experienced this? I have data in real-time in the current Lab Director, if I prefer not to rebuild.

  Thank you

  AW

  Besides that Graham mentioned,.

  > I brought the former hosts, with the same effect. I did then the labmanager to other VC instance he had never been associated, and he wouldn't see hosts there either.

  The Director of the laboratory cannot be associated with a single vCenter "Data center" object.  He memorizes the Objid of Datacenter and never delete it.  LM 4 should be able to work around this problem, or we can do something to erase the value manually.  But it would be better to try to verify the other steps first has affirmed here.

  > Then under management > resources section, click Resource Pools tab and select the "attach Resource Pool.

  > Select the resouce pool/ESX host you want on the shortcut menu.

  When you perform these steps, take a screenshot (in case it does not work).  I would like to see what objects have the Lab Manager icon already associated with them.

  Kind regards

  Jon Hemming, b.SC., RHCT, VMware vExpert 2009
  http://Twitter.com/vJonHemming

  If your question or problem has been resolved, please click the "right answer".  If someone helped him, please click "useful answer.

• Satellite C660D - flash cards are not displayed on the screen

  Hello
  I bought a Toshiba Satellite C660D a month ago. Everything was fine, until the FN button is no longer displayed the OSD menu.
  I looked on the forums and there were various tips on very similar issues. I downloaded the package of value added once again, I looked in the settings of flash card and nothing does the trick. Could someone help me?

  Any advice would be welcome.

  (ps, job functions, but the screen shows no more).

  What you can do is to call the Toshiba s hotline and ask for help.

  In any case, I think they can tell you the same thing: you can try to reinstall VAP or flash cards utility of support or reinstall OS using HARD drive recovery facility. With the settings, it works well again.

• open files are not detected when the research network file sharing

  Original title: cannot locate the file open in research

  Why when I search a document on my disk sharing (Windows 7) it will not display if someone else is open?  Is there an easy fix for this?  It comes if I scroll down, but if I search for it, it will not draw the document.  It is only when someone else is open.

  Due to complications involving the server shares, please create a new post on the TechNet support forum:

  http://social.technet.Microsoft.com/forums/en/w7itpronetworking/threads

• prompt (Functions) are not displayed in the user management responsibility

  Hello
  
  EBS 12.0.3
  
  I added the responsibility of user management with my user application it shows not all prompt (functions) that it is empty, while the sysadmin user's show.
  Kindly answer me.
  
  Thank you

  You have assigned the role of "security administrator" for the user and see if that helps?

  Thank you
  Hussein

• Satellite L755D - Web cam/mic are not detected by Skype

  Good evening everyone,

  I just noticed that when I install and open Skype, my built-in webcam and microphone are not detected by the application. He has worked in the past, but I've not had to use Skype for more than a year, so never noticed until now.

  I checked the Device Manager and there is no webcam or microphone listed. I tried to search for new hardware, but it found nothing.

  Specifications of systems:

  OS: Windows 8.1 Pro
  Processor: AMD A8 - 3500M
  Memory: 8 GB of RAM (2 x 4 GB Kingston sticks)
  HARD drive: 750 GB Seagate Barracuda
  The version of the BIOS: Insyde Corp. 2.10 (28/06/2012)

  If any other info is needed to help diagnose and solve this problem, then please ask and I will provide.

  Thank you very much

  Michael

  I guess the laptop not was not preinstalled with Win 8.1 but updated you the Win 7 system to Win 8.1.
  Is this correct?

  I m application because it would be interesting to know if the webcam worked correctly using Win 7.
  The driver for the webcam using Win 7 to be installed to get the webcam recognised.

  To help to win 8.1 additional webcam driver is not necessary because it s already part of the Win 8.1 System. That is why the webcam should appear in the Device Manager without installation of the webcam driver.

  However, some models of laptop supports additional webcam POWER setting in the BIOS.
  Please check this option in the BIOS.

• Satellite M30x + Win7: DVD not detected by the CD/DVD drive

  Hello

  I use a M30x since 2004 with its CD/DVD drive * a S mat. DVD-RAM UJ-831
  When I was with Windows XP, I have never had problems to read or write on CD, CD - R, DVD, DVD - R or DVD - RW. But recently I installed windows seven, and since that day the drive won't recognize the DVD. I can still read and burn CDs and CD - R. I'm burning the same Virgin DVD-+ R/RW as before, but the drive won't detect them. Those I have already burn are not detected or the other.
  My computer says that the CD/DVD drive work properly and drivers are up to date.
  I tried to clean the lens, but nothing has changed. And I tried to reinstall the drivers, but I could not found for windows seven.

  Thanks for the help.

  Hello

  Have you tried to delete the upper and lower registry Filters >
  Pleas check it!
  http://support.Microsoft.com/kb/270008/en-us

  You will find the registry key where filters must be removed.

• Some files in my USB SanDisk 16 GB USB key are not detected and when I connect to another PC, all files are detected

  Original title: some files in my USB are not detected and the rest of the files show find when I connect to my pc, when I connect to another pc the files seems to find.

  Hello world

  I have a SanDisk USB 16 G with important files, when I connect to my pc windows 7, some files are discovered, I am able to read other files show as empty files and my pc don't its not able to open them.

  When I connect the same USB for my lap top with windows 8 all the files where to find and I can open with a problem.

  Can some body please help me solve this problem?

  Hi Martin,

  This problem can be caused if the program for the particular file could not be installed on your computer.

  1. What is the file format or the extension of the files that you do not read or recognize in Windows 7?

  2. what exactly happens when you try to open empty files?

  3. have you made any recent hardware or exchange of software on your computer before the show?

  You need to check the files that are not open in Windows 7 and trying to install the software for files that are not opening and control.

  Let us know the status of the issue. If you need help, please after return. We will be happy to help you.

• movie maker error: a video capture devices are not detected

  Filmmaker gives the following statement. A video capture devices are not detected. My camera is plugged in and turned on. This has not happened before.

  What is it?

  How is it connected?

  Filmmaker works with mini camcorders dv connected FireWire, the firewire driver is installed by microsoft, you should not need to reinstall it, apart from a few special cases.

  This device and cable worked before?

  If so, what was the alst time and have you made any changes to the computer since then?

• Peripheral hardware devices - don't work or are not detected in Windows.

  Hardware devices do not work or are not detected in Windows.

  I have exactly the same problem. Is the returned message the Microsoft FixIt. No further details given. Nothing seems to be more information on the problem other than the claim that we exist.

• Satellite U500 - 1 DR series Notebook is not detected by the TOSHIBA site

  Hey,.

  My Toshiba Satellite U500 - 1DR Series notebook (Serial No. 1A058758R) is not detected by the automatic detection of TOSHIBA online system. When trying to get portable detected manually on the site, I stopped fingd the model (Satellite U500-1 DR) is listed in the list of available templates or models. I'm unable to download software/updates on the site.

  Hello

  If the work of autoetection doesn t you can find manually but not not using the name model but the model reference number. Your DR U500-1 has part number PSU9ME-xxxxx then please check under http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp Toshiba download page and look for Satellite U500 with reference number or model number short PSU9ME.

  Can find you it?

• Satellite A300-20 q are not on the tech support page

  Satellite A300-20 q are not on the tech support page. I can see 20 p, 20R, but not 20 q. Even a model automatic detector cannot find it in a database. Correct this error.

  Hello

  I don't know which pages or the database, you are meaning, but the Satellite A300-20 q is not available in all countries!

  This model was released for the Russia market.

  Other models of Sat A300-xxx are avaialbel on the other countries of South-East European/medium.

  Welcome them