Satellite-4070CDT asks for disc to update bios on each poweron

Similar Questions

• Satellite C660 - no Internet connection after updating BIOS

  I am a novice user and have a Satellite C660 under warranty that I don't use for surfing the net and Ebay so I hope I can explain my problem!

  Toshiba bulletin board said that the need to update BIOS, so I followed the instructions but since then I have no internet connection, and cannot restore the connection that I lost all help Toshiba Bulletin Board today lost and none of the programs to sort the problems work - e.g.set assistants etc. I did not yet create rescue disks, but if I try to create them now I'll be able to restore to factory settings?

  Can someone tell me if it's a failure caused by the BIOS update or I would return laptop to John Lewis for repair? Thank you very much for reading this

  Hey Buddy,

  The default settings in the BIOS load after update? If this is not the case, go into the BIOS and load the default settings. You can enter the BIOS if you press F2 before Windows start and then press the F9 key to load defaults. Then save & exit the BIOS Setup.

  You can access the Internet now?
  You try to access the Internet with LAN or WLAN connection?

  Also check device manager if all devices are recognized correctly.

  > I did not yet create rescue disks, but if I try to create them now I'll be able to restore to factory settings?
  You can create the Toshiba Recovery disk every time. Just launch the pre-installed Toshiba Recovery Media Creator and follow the instructions on the screen. You need just a few blank DVDs to create the discs. Disks contain a factory image of settings which can be restored each time and how many times you want to so with these disks, you are on the safe side ;)

• Satellite Pro L300D PSLC9E - failed to update BIOS

  Hi all

  I got a Toshiba Satellite Pro L300D Windows Vista Business, this isn't that four months, recently, he began to break up and whenever he did, I got a message to upgrade the BIOS.
  So I went to the Toshiba Site and I downloaded an updated BIOS yesterday and installed even today, during installation the PC frooze.
  I left it on and it stayed like that for four hours, then it turns off.

  Now, when I turn it on all that I get is the fan turns to nothing else.
  The powerleader was connected to the laptop all the time.

  Do you have any ideas on what I can do, I have heaps on the laptop I would not loose.

  Model is PSLC9E Satellite Pro L300D

  The case is clear buddy update the BIOS has no procedure
  Perhaps the BIOS might not be updated correctly because the laptop crashed until the update procedure could be completed.

  Well, I can tell you that you will not be able to fix it yourself it's a serious issue and ONLY the ASP (certified partner) would be able to help you!

  So contact the ASP technician and ask for later handling.

  Good luck

• M92p Tiny - no bootable disc after update BIOS to 9SKT59A (dual boot Linux/Win7) GPT/EFI

  Hello

  I've updated my Lenovo ThinkCentre m92p tiny A1G 3237 - to the 9SKT59A of the BIOS version.
  I use a SSD OCZ with GRUB2 and Win7/Linux dualboot (UEFI/GPT) without any problem.

  After that the updated BIOS update it was SecureBoot activated and I couldn't start obviously GRUB2.

  Then I disabled SecureBoot and changed the boot order, but when I try to include the SSD with x, it disappears from the list excluded bootable devices but do not appear in the devices included.

  Now, I'm only able to boot using USB key where a grub2 is also installed. I'm sure it's a bug in the BIOS!

  Can anyone else confirm or solved this probem?

  See you soon

  Mijenix

  Updated the BIOS to 9sj960usa fixed the problem for me. As I was not able to boot using CD/USB-SSD, I was able to GRUB2 boot Win7 on a USB key and has used the flash .exe file.

• Install Adobe CS6 Design and Web Prem, asking for disc?

  I want to install Adobe CS6 Design and Web Prem, I downloaded through Adobe and have a license for.  During the installation, it asks to put a disk, which I did not, because I downloaded the application.  Why does he ask a disc?

  Hello

  Try to download it from our Web site: http://www.adobe.com/cfusion/tdrc/index.cfm?product=designweb_premium

  and check.

  Kind regards

  Ravi

• Satellite C50B freezes at startup after update BIOS to 5.10

  Hello
  I updated the BIOS of my Satellite C50 - B - 14 d (PSCMLE) to 5.10 (a final release early sept. 2015).
  The update succeeded, and the laptop runs as long as I do not install the drivers for the card WiFi (Atheros AR9485).
  If I try to install the driver (it does not matter which, those of the Toshiba website or those of the manufacturer, of), the laptop crashes before the end of the installer.
  Installing drivers from Device Manager makes the laptop freeze on when Windows starts (I tried 7, 8.1, and 10).
  Completely on the Windows logo screen it freezes, and I have to turn off it.

  In addition, the wired network adapter is not detected (it does not appear in Device Manager).
  The same question is described here (http://www.eightforums.com/general-s...ses-start.html), but no solution.

  Any suggestion? The BIOS may be downgraded? The BIOS update utility does not Flash an older version.

  Thank you!

  Hi indutry,

  I also have exactly the same problem since updating my BIOS to 5.10 with my Toshiba C50 - B - 14 d PSC MLE

  I have to start windows in safe mode without network to disable the Atheros AR9485 before restarting again in normal mode.
  I now have to use an external WiFi adapter as my LAN port is now also lack!

  Upset that the BIOS update has broken all my embedded network on the laptop.

  I tried to update the Atheros drivers to the latest version, but as soon as the device is turned on again the system crashes and we're back to square one.

  There is no solution that I can find other than turning off the unit and live without built in WiFi + LAN.

  I hope Toshiba can be remedied with a new BIOS update?

• Satellite A300 - pad touch dead after update BIOS 2.20

  Hello

  exact model is Satellite A300 PSAGCA-06M01N under Win XP.

  I had a problem with the webcam, and I read in the forum that it can be solved by a BIOS update. so, I advanced and downloaded the latest version of the BIOS on the site of toshiba, especially for my laptop model. It went quite well with no error.

  However when the computer restarts after that the BIOS updated my touchpad no longer works.
  I went to Device Manager and could still see the Synaptics touchpad device and it says "this device is functioning correctly. but its completely dead and will not respond with the 2 keys. before I updated the BIOS I never had any problems with it.

  I tried FN + F9, nothing helps. plugged in a USB mouse and it works without any problem. In fact, when I plugged in the mouse the synaptics software says "Deactivation of the key because of the external pointing device" for the device driver for the touchpad works.

  If I remove the mouse, it will say the touchpad is restored, but it still doesn't work. restarted several times and still the same problem. went into BIOS and chose "default" not still a no go.

  Can someone offer any advice or ideas please?
  I really need the touchpad for the way I use the laptop...

  Hello

  In many cases, the touchpad (pointing device) can be enabled and disabled in the BIOS.
  I think you should check if this option is available in BIOS and if so, check whether it should be enabled.

• Satellite P500 - screen remains blank after updating BIOS 2.90

  I installed the new WOOD update through the station of service and after restart, the screen remains blank (out of service)?

  Any suggestions?

  Hello

  And on the external monitor you see a photo or not?

  In my opinion, something goes wrong during the update of the BIOS, and so the entire computer doesn t start anymore. All updates are pre-tested by Toshiba, so I doubt that only the screen isn't working anymore.

  You should try to remove the battery and unplug the AC adapter for an hour. Then install the battery and plug in the AC adapter. Make sure the battery is fully charged and then try to start your laptop.

  It's working now?

• Satellite Pro L670 - 14 p - cannot update Bios - error message appears

  Hello

  I downloaded the latest update of the Bios for the computer laptop afforementioned, and it is not allowing me to update. It says that I need to make sure that: Bios is not later than 210 (mine is 1.80), AC is connected (it is), and that the battery is greater than 10% fee (mine is 100%).

  I have tried everything I can think (update running as administrator, reset the bios by default, removing all power from the laptop for half an hour etc.) and I still get this error message?

  Does anyone else have this problem?
  Its got that puzzled me.

  Thanks in advance for any help!

  See you soon,.
  Craig

  Hello

  Did you install VAP (value added package)?
  If so, uninstall and update this tool. Once again install it and restart the laptop.
  Then try to update the BIOS once more.

  Good luck

• Re: Satellite A300 won't start after updating BIOS

  Today I was installing recommended THAT BIOS update 1.70 to 1.90. During installation, the mouse cursor disappeared and has no reaction to the keys on the keyboard. But there was a message DO NOT TURN OFF COMPUTER. So I waited for long (an hour?), but the update progress bar was always in the same place - as my computers are suspended.

  After a long time waiting without any response, I decided to reset the computer. Only way to do pressed turn on button for a few seconds.

  But after that turn it on again there is nothing visible on the screen, only the reaction of the computer is that bright development under tension is turned on and hard drive will blink every two seconds. What should do? Please help me! I have very important data on the hard drive at this moment! Can I reset the BIOS? I tried to yutm on the computer after you press ESC and F2 key, but no effect. I put the CD with the operating system, but no effect.

  Its possible that the BIOS chip is faulty, causing the update to the BIOS to fall down during the writing process.

  If you have tried reinstalling the RAM and removing the power for an hour, it is not great thing else you can do except send it to an ASP for warranty repair.

• Satellite pro c660 - 21 d cannot update BIOS

  Windows7 64 bit
  talktalk f-secure antivirus

  Downloaded BIOS_V200_WIN. EXE, when had alert tempo today

  clicked on run as administrator
  extract the files and box
  Phoenix uefi winflash
  analise old and new bios
  WinFlash for uefi has stopped working
  close the program
  Event Viewer shows

  Name of the failing application: winflash.exe, version: 1.1.26.0, time stamp: 0x4b0b90c3
  The failed module name: unknown, version: 0.0.0.0, time stamp: 0x00000000
  Exception code: 0xc0000005
  Offset: 0 x 02774020
  ID of the process failed: 0 x 1474
  Start time of application vulnerabilities: 0x01cd68c5e0d498a8
  The failing application path: C:\Program Files (x 86) \UEFI WinFlash\winflash.exe
  Path of the failing module: unknown
  Report ID: 1f73efe4-d4b9-11e1-a41b-b870f4c55a8a

  also

  Fault bucket 2563155615, type 5
  Event name: BEX
  Answer: No available
  Cabin ID: 0

  Signature of the problem:
  P1: winflash.exe
  P2: 1.1.26.0
  P3: 4b0b90c3
  P4: StackHash_e8ad
  P5: 0.0.0.0
  P6: 00000000
  P7: 02774020
  P8: c0000005
  P9: 00000008
  P10:

  Attached files:
  C:\Users\Ken\AppData\Local\Temp\WER2E9E.tmp.WERInt ernalMetadata.xml

  and finally

  Fault bucket 0, type 5
  Event name: PCA2
  Answer: No available
  Cabin ID: 0

  Signature of the problem:
  P1: BIOS_V200_WIN.exe
  P2: 4.65.0.0
  P3: 7z SFX Setup
  P4: 7 - Zip
  P5: Igor Pavlov
  P6: 1
  P7: 200
  P8:
  P9:
  P10:

  I wonder if the f-secure anti-virus is blocking the update of the bios

  I don't want to remove it unless it's the culprit

  > I wonder if the f-secure anti-virus is blocking the update of the bios

  Before running the BIOS update tool, you should close all applications running in the background and need to disable firewall and antivirus too!

  In addition the VAP (value added package) must be installed on your laptop.
  The VAP is a package of tools of Toshiba which is on the European driver Toshiba page.

• Satellite A100-237 (PSAA9) crashes after update BIOS 5.10

  I have a psaa9 A100-237
  I recorded my book and went in the updates section
  There was an update of the available BIOS, I had version 2 before I updated to 5.10.

  Now everything has gone well, but the laptop is restarted, it blocks every time on the start screen where the toshiba logo is displayed.
  I can't log into BIOS, boot from the CD or anything.
  When I press ESC black screen just showing bios version 5.10 memory pass and things, also written there is error TRM (TPM?) or not found.

  I used the method of updating the bios windows and followed all the directions, wts the problem?

  Hello

  May I ask why you updated the BIOS?
  You are 100% sure that you have updated the BIOS with the correct procedure and used the good BIOS?
  Have you read the Description of the Toshiba BIOS update before continuing?

  As far as I know the BIOS 5.1 has been released to use and install Vista on this laptop!
  Hmm, maybe something goes wrong during the update procedure and, therefore, the laptop cannot load and start correctly.

• Satellite A60: Problem of memory after update Bios V.1.9

  Hi all

  I've just updated my bios to version 1.9 last week. Previously, I've upgraded my RAM from 512 MB to 1.5 GB (P4 2.8 GHz., 40 GB HARD drive) and my phone worked perfectly with the old Bios and RAM. After the Bios Update to the new version, 1.9, my laptop does not accept the module of RAM upgrade, windows xp still shows the blue screen, and then restart.

  After upgrading RAM off, my laptop works again. I tried several ways to solve this problem as take the battery, then reinsert the RAM or even formatted my HARD drive and installed a new Windows XP, but it didn't work. So what can I do to make my laptop to accept the upgrade of RAM? How to solve this problem? For this reason I now intend to buy a new laptop, if the problem can not be solved since I simulate a program on this laptop, so it requires a lot of memory.

  Thank you very much in advance for your answer.

  [Edited by: admin]

  Hello

  I put t really know what is the problem with the new update of the BIOS. In my opinion, you should contact the after-sales Service of Toshiba partner in your country and explain to them the situation. If your new module memory is compatible with the unit you should tell you want to have the old version of the BIOS. As much I know as technicians for this.

  If they see that there is a problem with the BIOS update, I'm sure they will for free.

  Good luck!

• 430cds asks for disc system on start up

  I wonder if anyone knows what the problem is with my laptop, I have it lent to a friend for a few months work in order, that she is back and now everything he said start up is "insert a system disk in drive press a key when it is ready.
  Unfortunately all the discs I have both floppy and cd fail to initialize when entered... If the machine has been completely erased. If so how can I put the systems in place. It is a good laptop and wouldn't have to be scrapped, he... Bravo dave b

  [Edited by: admin August 7 05 13:46]

  Hello

  In my opinion you should ask your friend did it with your device. On this way, we can only speculate what the problem is, but there is a problem with the operating system, and it cannot start.

  As Sam said the best way is to install the OS by using the recovery CD.

  Good bye

• Satellite P300 cannot connect WiFi after update BIOS

  Hello

  After using the original BIOS updated to programm my P300 - 18M can not find wireless networks.

  I've updated with file BIOS on 2008-09-22 without any problem. The strange thing is: using the network wireless switch
  in front of the P300, it activates the Bluetooth on or off instead of the wireless network card. The wireless card is now is still running, but can't
  find any network.

  Another labtop sees several wireless networks, as well as the P300 did before upgrading the BIOS.

  Can someone give me some advice or help me with an older version of BIOS for Windows XP?

  Thnx!

  John

  Hello

  Very strange problem, but maybe it can be solved very easily
  You should try to simply update the WLan driver.
  In addition, you should access the BIOS and it should define the default settings.

  Check it out!