Satellite P500 - screen remains blank after updating BIOS 2.90

Similar Questions

• Satellite Pro P300 - screen remains blank after power on

  My Toshiba Satellite Pro P300 power on, the screen remains blank.

  Can someone please help?

  Looks like a FL. inverter problem
  I doubt that you could replace is it s a job to a service technician.
  The FL Inverter control the backlight of the screen and if it s faulty, you will see everything as behind a thick fog

• Satellite C660 - no Internet connection after updating BIOS

  I am a novice user and have a Satellite C660 under warranty that I don't use for surfing the net and Ebay so I hope I can explain my problem!

  Toshiba bulletin board said that the need to update BIOS, so I followed the instructions but since then I have no internet connection, and cannot restore the connection that I lost all help Toshiba Bulletin Board today lost and none of the programs to sort the problems work - e.g.set assistants etc. I did not yet create rescue disks, but if I try to create them now I'll be able to restore to factory settings?

  Can someone tell me if it's a failure caused by the BIOS update or I would return laptop to John Lewis for repair? Thank you very much for reading this

  Hey Buddy,

  The default settings in the BIOS load after update? If this is not the case, go into the BIOS and load the default settings. You can enter the BIOS if you press F2 before Windows start and then press the F9 key to load defaults. Then save & exit the BIOS Setup.

  You can access the Internet now?
  You try to access the Internet with LAN or WLAN connection?

  Also check device manager if all devices are recognized correctly.

  > I did not yet create rescue disks, but if I try to create them now I'll be able to restore to factory settings?
  You can create the Toshiba Recovery disk every time. Just launch the pre-installed Toshiba Recovery Media Creator and follow the instructions on the screen. You need just a few blank DVDs to create the discs. Disks contain a factory image of settings which can be restored each time and how many times you want to so with these disks, you are on the safe side ;)

• Satellite L670 - screen remains black after sleep mode

  I recently bought a L670. When I close the laptop, it goes into sleep mode. No problem with that. But when I opened the laptop again the screen remains black.
  I see on the drive activity light that the laptop come out of sleep mode correctly, but the screen remains black.

  I don't have this problem when the sleep mode is only a few minutes. Then the screen comes up correctly.
  But for example after an hour of sleep mode... no screen.

  I'm doing something wrong?

  Thanks in advance for your feedback.

  Hello

  I recommend the update to the BIOS and the display driver.
  It helped to solve a similar problem on my old laptop.
  Maybe it helps in your case.

  Good luck

• Satellite A60: Problem of memory after update Bios V.1.9

  Hi all

  I've just updated my bios to version 1.9 last week. Previously, I've upgraded my RAM from 512 MB to 1.5 GB (P4 2.8 GHz., 40 GB HARD drive) and my phone worked perfectly with the old Bios and RAM. After the Bios Update to the new version, 1.9, my laptop does not accept the module of RAM upgrade, windows xp still shows the blue screen, and then restart.

  After upgrading RAM off, my laptop works again. I tried several ways to solve this problem as take the battery, then reinsert the RAM or even formatted my HARD drive and installed a new Windows XP, but it didn't work. So what can I do to make my laptop to accept the upgrade of RAM? How to solve this problem? For this reason I now intend to buy a new laptop, if the problem can not be solved since I simulate a program on this laptop, so it requires a lot of memory.

  Thank you very much in advance for your answer.

  [Edited by: admin]

  Hello

  I put t really know what is the problem with the new update of the BIOS. In my opinion, you should contact the after-sales Service of Toshiba partner in your country and explain to them the situation. If your new module memory is compatible with the unit you should tell you want to have the old version of the BIOS. As much I know as technicians for this.

  If they see that there is a problem with the BIOS update, I'm sure they will for free.

  Good luck!

• Satellitr L50D - screen remains blank after standby

  Satelite L50D-B, CPU AMD A6, AMD Radeon R4, Windows 8.1 x 64 display.

  Recovery from sleep mode screen remains empty, one led.
  Back to sleep and resume again brings back the normal screen.
  Tried all combinations in setting energy and latest AMD Radeon driver: no result.

  Thanks for providing the solution.

  Have you noticed the same problem after standby and Hibernate?

• Satellite C50B freezes at startup after update BIOS to 5.10

  Hello
  I updated the BIOS of my Satellite C50 - B - 14 d (PSCMLE) to 5.10 (a final release early sept. 2015).
  The update succeeded, and the laptop runs as long as I do not install the drivers for the card WiFi (Atheros AR9485).
  If I try to install the driver (it does not matter which, those of the Toshiba website or those of the manufacturer, of), the laptop crashes before the end of the installer.
  Installing drivers from Device Manager makes the laptop freeze on when Windows starts (I tried 7, 8.1, and 10).
  Completely on the Windows logo screen it freezes, and I have to turn off it.

  In addition, the wired network adapter is not detected (it does not appear in Device Manager).
  The same question is described here (http://www.eightforums.com/general-s...ses-start.html), but no solution.

  Any suggestion? The BIOS may be downgraded? The BIOS update utility does not Flash an older version.

  Thank you!

  Hi indutry,

  I also have exactly the same problem since updating my BIOS to 5.10 with my Toshiba C50 - B - 14 d PSC MLE

  I have to start windows in safe mode without network to disable the Atheros AR9485 before restarting again in normal mode.
  I now have to use an external WiFi adapter as my LAN port is now also lack!

  Upset that the BIOS update has broken all my embedded network on the laptop.

  I tried to update the Atheros drivers to the latest version, but as soon as the device is turned on again the system crashes and we're back to square one.

  There is no solution that I can find other than turning off the unit and live without built in WiFi + LAN.

  I hope Toshiba can be remedied with a new BIOS update?

• C55-A-100 satellite does not power down after update BIOS 1.30

  A week ago, the Toshiba software installed on my C55-A-100 Satellite suggested that I installed a new version of the BIOS to 1.3.

  Since installing it my Satellite will not turn off.
  If I close the lid the screen turns off but the laptop is running, if I open the lid nothing happens and I have to keep my finger on the power button to force it to close.

  The same thing happens if I press the power button to turn off, blank screen and it continues to run, then I have to force a shutdown by holding the power button pressed down. I also noticed that the satellite seems to take ages to power.

  Can anyone provide a solution or experienced the same problems.

  The Satellite is running win 8.1

  Thank you

  Ben

  Please change, as described on http://aps2.toshiba-tro.de/kb0/TSB2B03EY0002R01.htm and try to proceed to a complete stop.
  It work correctly?

  Have you noticed this problem just at the moment where you change the options of closing lid and pressing the power button?

• Re: Satellite A300 won't start after updating BIOS

  Today I was installing recommended THAT BIOS update 1.70 to 1.90. During installation, the mouse cursor disappeared and has no reaction to the keys on the keyboard. But there was a message DO NOT TURN OFF COMPUTER. So I waited for long (an hour?), but the update progress bar was always in the same place - as my computers are suspended.

  After a long time waiting without any response, I decided to reset the computer. Only way to do pressed turn on button for a few seconds.

  But after that turn it on again there is nothing visible on the screen, only the reaction of the computer is that bright development under tension is turned on and hard drive will blink every two seconds. What should do? Please help me! I have very important data on the hard drive at this moment! Can I reset the BIOS? I tried to yutm on the computer after you press ESC and F2 key, but no effect. I put the CD with the operating system, but no effect.

  Its possible that the BIOS chip is faulty, causing the update to the BIOS to fall down during the writing process.

  If you have tried reinstalling the RAM and removing the power for an hour, it is not great thing else you can do except send it to an ASP for warranty repair.

• Satellite A300 - pad touch dead after update BIOS 2.20

  Hello

  exact model is Satellite A300 PSAGCA-06M01N under Win XP.

  I had a problem with the webcam, and I read in the forum that it can be solved by a BIOS update. so, I advanced and downloaded the latest version of the BIOS on the site of toshiba, especially for my laptop model. It went quite well with no error.

  However when the computer restarts after that the BIOS updated my touchpad no longer works.
  I went to Device Manager and could still see the Synaptics touchpad device and it says "this device is functioning correctly. but its completely dead and will not respond with the 2 keys. before I updated the BIOS I never had any problems with it.

  I tried FN + F9, nothing helps. plugged in a USB mouse and it works without any problem. In fact, when I plugged in the mouse the synaptics software says "Deactivation of the key because of the external pointing device" for the device driver for the touchpad works.

  If I remove the mouse, it will say the touchpad is restored, but it still doesn't work. restarted several times and still the same problem. went into BIOS and chose "default" not still a no go.

  Can someone offer any advice or ideas please?
  I really need the touchpad for the way I use the laptop...

  Hello

  In many cases, the touchpad (pointing device) can be enabled and disabled in the BIOS.
  I think you should check if this option is available in BIOS and if so, check whether it should be enabled.

• Satellite P100: screen remains black after the awakening of the mode standby

  Hello!!
  Can someone help me with this problem?
  I update my bios [V3.30] 12.22.2006 and now I have a problem.

  When I put my laptop P100 in stand by and I return my screen no longer works! I push every button on my keyboard, I move my mouse but nothing.
  Only one solution to come back is to close my laptop and reopen after that.

  What to do? Please help me if you have any ideea!
  Best regards to all!

  Hello

  I hope that you used the good BIOS.

  Have you tried to update the graphics driver? Not? Then do it!

• Satellite M100 - screen remains black after sleep/wake

  I just installed Windows Vista Ultimate on my Satellite M100 series.

  Everything works fine, but when the pc is forced into sleep/standby or it automatically goes into sleep/standby mode depending on the time of inactivity in the power settings could not be restored sleep/wake without turn off and restart.

  The blue button is orange and blinking indicating sleep/standby mode. When you press it again, it turns blue and the fan turns on. But there is no display and no response. The only option is to go to market.

  Help, please

  Hello

  What BIOS updated to the latest version?

• Satellite L50: Win8.1 disabled after updating BIOS

  Hello

  I ve upgraded my BIOS of L50 Satellite to the latest version. Then windows disabled and can not enter the product manually key. Can't do the phone activation too.

  When I click on activate Windows, it just goes to the start screen. I ve tried to restore the system and it's the same thing. Any advice?

  Thanks in advance.

  Hello Sergio
  I don't know what L50 do you have exactly, but if your laptop comes with preinstalled OS, I recommend you to reinstall the OS using HARD drive recovery option and check this once more.

  Can you please send your L50 exact model number?

• Satellite A100-237 (PSAA9) crashes after update BIOS 5.10

  I have a psaa9 A100-237
  I recorded my book and went in the updates section
  There was an update of the available BIOS, I had version 2 before I updated to 5.10.

  Now everything has gone well, but the laptop is restarted, it blocks every time on the start screen where the toshiba logo is displayed.
  I can't log into BIOS, boot from the CD or anything.
  When I press ESC black screen just showing bios version 5.10 memory pass and things, also written there is error TRM (TPM?) or not found.

  I used the method of updating the bios windows and followed all the directions, wts the problem?

  Hello

  May I ask why you updated the BIOS?
  You are 100% sure that you have updated the BIOS with the correct procedure and used the good BIOS?
  Have you read the Description of the Toshiba BIOS update before continuing?

  As far as I know the BIOS 5.1 has been released to use and install Vista on this laptop!
  Hmm, maybe something goes wrong during the update procedure and, therefore, the laptop cannot load and start correctly.

• Satellite P300 cannot connect WiFi after update BIOS

  Hello

  After using the original BIOS updated to programm my P300 - 18M can not find wireless networks.

  I've updated with file BIOS on 2008-09-22 without any problem. The strange thing is: using the network wireless switch
  in front of the P300, it activates the Bluetooth on or off instead of the wireless network card. The wireless card is now is still running, but can't
  find any network.

  Another labtop sees several wireless networks, as well as the P300 did before upgrading the BIOS.

  Can someone give me some advice or help me with an older version of BIOS for Windows XP?

  Thnx!

  John

  Hello

  Very strange problem, but maybe it can be solved very easily
  You should try to simply update the WLan driver.
  In addition, you should access the BIOS and it should define the default settings.

  Check it out!