Satellite A110 - 159 hangs when it is connected to the LAN card

Similar Questions

• Satellite M40-281: Fedora Core 4 does not recognize the LAN card

  Fedora Core 4 recognize everything my satellite M40-281, except for the LAN card :-(

  What can I do?

  Thanks and... Sorry for my English (I'm Italian!)

  which

  Hello

  Don t support Toshiba laptops Linux distributions. Computers laptop Toshiba are distributed and tested with the Microsoft Windows operating system.

  As far as I know, this device was shipped with Marvell based PC Express I / F LAN (I / F Marvell chip at base of PC Express I / F)
  Well, you can try glasses a bit. You might find a driver for Linux.

  In addition, the Fedora Core 4 is based on a Red Hat Linux distribution. So I recommend you to visit this site:
  http://www.redhat.com/en_US/USA/Fedora/

  Good luck

  Good bye

• OfficeJet Pro 6830 hangs when it is connected to the network

  I just pick up a Pro OfficeJet 6830. I installed the ink cartridges and it seems to be able to print copies and test pages, but I can't seem to connect to my network. Here is what I tried:

  Using the Wireless Setup Wizard

  I selected my network in the list and entered my WPA key. It says it tries to connect, then the following occurs:

  1 briefly press (for less than one second), a screen will appear showing that it has successfully connected to the network.

  2. Press briefly (for less than a second) the screen flashes blue with an icon of 'power' and 'B8B2A4F8' text (which I assume is an error code).

  3. the screen display changes to "printer error: there is a problem with the printer.» "Turn the printer off, then on.

  4. after restarting the printer, he complains that he has not been arrested properly.

  Any other attempt to connect gives the same results.

  Ethernet connection

  If I turn on the printer when connected via Ethernet cable to my network, after about 10 seconds it crashes as described above (steps 2 and 3) without doing me anything at all.

  I also tried a "Hard Reset" (i.e. unplug the printer for 60 seconds, and then it turning it back on again). This made no difference whatsoever.

  I managed to get it to connect to a WiFi hotspot on my laptop (and I checked the firmware updates, but unfortunately there is none available), it seems that there is something of my network that do not have the printer. I have no idea what this could be, however. Someone at - it ideas?

  It solved!

  I spent a bit of time on the phone with HP tech support and the guy could not actually solve the problem for me but it helped prove that the hardware network printer works OK. I could connect the printer directly to my PC via Ethernet, then ping and access the built-in web server.

  It occurred to me that perhaps the problem was related to DHCP, because the printer broke immediately after the connection to the network. My router is an Asus RT-N66u with custom firmware (version Asuswrt-Merlin 376.48_3) and I could see the router newspaper that he was sending a DHCP acknowledgement to the printer just before he died.

  So, here is what I did to solve the problem:

  1 turn off the DHCP server on the router.

  2. on the printer, operated the network icon on the homescreen (at the Middle bottom) wireless.

  3 typed down "gear" icon to the left (settings).

  4 typed "wireless settings".

  5 typed "Assistant wireless configuration".

  6 selected my wireless network and entered the WPA key. This time, no crash, but he did not get an IP address assigned (obviously).

  7. back in 'Wireless Settings', I typed in 'advanced settings '.

  8 typed 'IP Settings'.

  9. tapped "manual (static).

  10. enter in the details for my network - yours will probably be different, but I entered in what follows:

  IP address: 192.168.002.201 (I chose this because it is outside the range of addresses, the router for DHCP problems).

  Subnet mask: 255.255.255.0

  Default gateway: 192.168.002.001

  DNS address: 192.168.002.001

  11 hit 'apply '.

  12 re-enabled the DHCP server on my router.

  And now it works!

• Satellite Pro U300 - how to go if connected to the LAN WiFi

  How can I change my laptop to the wireless router, when you connect to the internet LAN?
  My laptop is Toshiba Satellite U300 pro

  Post edited by: marto_noa

  Unplug the cable LAN and switch ON the WLan.
  Usually the laptop would use the LAN connection if LAN cable is connected and LAN is active.

• When it is connected to the LAN, FF cannot find servers; no problem with the wi - fi

  26.0 Firefox running on a Windows 8.1 System. The thing I meet is this: I have no problem loading of pages and surfing when I am connected to my wi - fi network (I have a double function modem that wireless and LAN at the same time). However, whenever I plug the LAN cable, I get the error message that Firefox can't find the server. In this case if I disconnect the wireless at the same time. BUT, if I continually press the button [start] or simply tap the icon reload the page in the address bar, will eventually load, usually after a few failed attempts. However, the page loads usually only partially in a first time, apparently without advanced HTML formatting. But, after clicking on reload again one or two times, the page loads normally. Unknown, is that the behavior is not consistent - some pages of charge very well. But I can't for the life of understand me a boss.

  I've tried troubleshooting by disabling NoScript, but it doesn't seem to make a difference.  It's almost as if the wait time for a response from the server is so minimal when connected to LAN that the server has no chance of loading the first time.  Does that make any sense?  If so, how can I go about fixing the issue?
  

  Thanks for any help you can offer on this (for me, anyway) head-scratcher.

  Maybe another DNS server is used or there is still cached data.

  Have you tried a hard facing to bypass the cache to refresh all files?

  • Hold down the SHIFT key and click the Reload button
  • Press 'Ctrl + F5' or 'Ctrl + Shift + R' (Windows, Linux)
  • Press 'Command + shift + R' (Mac)

  You can also try to switch to work offline/off voltage after changing the network connection.

  If is also possible that your firewall treats the Wi - fi connection other than the connection to the local network.

• Satellite Pro P300 - 20 h: unable to connect to the WLan card and LAN disappeared

  Hi guys!

  I had my computer a little more than 6 months and suddenly came up with 2 problems!

  First the LAN adapter seems to have deleted the drivers it is, in itself, and apparintly to remove the entire map in general.
  I don't know how this can happen, because the computer was untouched for 3 months that I've been away!

  Secondly the packed wireless, the wireless says he works on the Device Manager, but when I try to connect or never discover the networks, it will not let me connect and tells me that he cannot see the networks! When my brothers computer he can find same networks!

  It is really strange and annoying reallllyyy!

  Thanks in advance.

  Carl.

  Are updated Microsoft on automatic installation?

  Try reinstalling the drivers LAN and WLAN.
  Driver WLAN, you can find the Toshiba WLAN Portal under http://aps2.toshiba-tro.de/wlan/
  Maybe your brother is right settings WLAN. compare the settings with his computer and make sure you use the correct password if the WiFi network is protected.

• Satellite C660-1DK overheating when you are connected to the dynadock station

  Hello

  I recently bought a Dynadock U10 (PA3575E-2PRP) docking station, to get a great full how to use my laptop 3. No luck, perfect functioning of Sony and Nec, Toshiba C660-1DK don't: (o)

  OK, I noticed that the C660 is not in the list of laptops supported the Dynadock.

  In any case, there must be something for a Toshiba laptop? So here's the snippet:

  -configuration (with the latest drivers online) and connection beetween Dynadock and C660 smoothly
  -After a few minutes, running fan a cooling of laptop fires throtlle full speed.
  -to 70-degree temperature, C660 stop automatically.

  My OS is Windows Seven 64-bit original.

  Thanks for any help that you could provide

  Bests

  Stéphane

  Hello

  Dynadock is certainly supported by C660. So this shouldn't be a problem.

  > After a few minutes, running fan a cooling of laptop fires throtlle full speed.
  > 70-degree temperature, C660 stop automatically

  Check that the cooling modules are free of dust. Dust affect the performance of module cooling and this could lead to a higher temperature.
  Spray with compressed air to remove dust from the fans.

  The use of graphics drivers from Toshiba is also very important! Drivers Toshiba supports the overheating protection so you need to check if the use of drivers Toshiba could help!

• HP 1200 printer does not print check when it is connected to the Jetdirect card but will display the report

  HP 1200 printer is plugged in with the USB cord to HP Jetdirect box and it gets IP from there.   Printer is set for the server with the ip 192.168.10.7 of print

  Print server is 192.168.10.12.    Backend server account try to print to a control with the 1200 HP and output hit the print queue (we suspended the print queue)

  and then when we release printing printing disappears as his will be printed but no keys comes out.      As a test, we ran a simple report on the same printer who had no special formatting and it printed fine.

  Captured audit printing to a file and then realized that file to the other printer, HP Officejet K80, which was not intended for printing and it prints properly which confirms that the control is built in formatting standard code PCL5e.   What is unexplained, that's why the cheque will not be printed on the HP 1200.    Have already had experiences where the USB slave out of Windows workstatoins printers will not print documents at all the other stations of the network.   The print will be struck by the print queue and disappear, but the printer never lights.   In this case, it will work for printing unformated but won't work for the formatted print PCL.   This could be Windows networking printers or simply a problem with the HP 1200 and forum for both checking.

  Hello

  1. are you able to print Word documents, Excel and PDF?

  2 are computers and printers connected to a domain network?

  I suggest you to connect the printer directly to the computer and check if it helps.

  Please visit the following links and check.

  Printer network problems (applies to Windows 7 as well)
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Let us know if it helps!

• Satellite A110-159 restarts no CD

  Hello

  My Toshiba Satellite A110-159, Windows XP SP3 contains a system error and does not restart (not in safe mode). start the computer by using the last known good configuration does not work either. I also tried to change in the BIOS boot order, put the CD/DVD first started, but that did not help.

  Problems occurred after trying to clean my system of a virus antivirlock.com by virus scan AVG running from the command prompt in safe mode. I think that some of my registry I messed up.

  It keeps giving a blue screen with the following error message:

  STOP: c000021a {fatal system error}
  The Windows Logon Process system process ended unexpectedly with the status of 0xc0000034 (0x00000000 0 x 0000000)
  The system has been turned off.

  .. .and then it restarts again. He is not able to open the windows or anything like that.

  I decided to restart my system using Toshiba recovery disks. (I have a resumption of Norton Ghost of my C drive on an external drive and a plan to replace it once I have the system in factory again).

  Following the instructions that I inserted the recovery disc 1/2, you press F12 and in the selected Menu de Boor:
  CD/DVD MAST * ADVD-RAM UJ - 841 - S (SM)
  and then you press ENTER.

  And then it gives a window where he begins to check for Realtek Ethernet or something, can't find (no cable atttached) and then starts loading Windows and which gives the familiar blue screen and reboot again.

  Therefore, it does not recognize or read the CD in the drive. I searched other threads for clues, but most gives options to change something in the registry, install drivers, etc.. I can't do anything about that, because Windows does not start.

  Can someone tell me how to get my laptop working again? Thank you very much in advance.

  Best regards, Ivo

  Post edited by: ief1000

  Hello

  Download Windows copy disk and try to install it. The recovery disk, you are using may be corrupted...

• Satellite Pro C70 - could not get the image when it is connected to the projector

  This machine has been purchased for use in the classroom with projector and smart board. When it is connected to a monitor, the second screen works fine, but when it is connected to the projector DLP Epson, the computer screen and the projector are the two laptop PC empty of other manufacturers of work correctly when it is connected to the projector.

  Can you help me?

  Message has been modified: name of the laptop has been added to title

  What laptop do you speak?
  .. .and what operating system is preinstalled on this laptop?

  You use the pre-configured Toshiba system?

  Is the resolution of the screen for both devices (display and external monitor) set correctly?

• Hai, my ipod shuffle when it is connected with the computer, it flashes organge light.  If I don't take no light

  Hai, my ipod shuffle when it is connected with the computer, it flashes orange light.  If I remove without light and music.  Even I kept connected all day with my laptop for charging.  But without success.  Is it possible to change the battery?

  If the shuffle still appears in iTunes when you connect, you can try to do a restore using iTunes, where the cause is a software problem.

  Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod settings - Apple Support

  If the problem reoccurs after the restoration, it's probably a battery worn.  Need soldering skills to replace yourself, and iPod shuffle (with the exception of the 1st generation) is very small.  Not easy to work on.  This web site has repair guides

  https://www.iFixit.com/device/iPod_Shuffle

  and parts are available from sources like eBay.

  Apple 'serve' the shuffle, if it's the 4th gen (current type).  Rather than change the battery of your device, you get a replacement unit.  According to this document, out-of-warranty fees are $39

  Pricing of the Service - The Apple iPod Support

  NOTE: If your shuffle is less than one year of the date of purchase, it is under warranty.

  The retail price of a brand new 4th gen iPod shuffle, with new headphones, docking cable and warranty of one year is $ 49.

• I have the macbook pro (OS 10.6.8) and the iphone 6 s. The latest version of iTunes is 11.4. When it is connected to the MAC, I get the message that itunes must be upgraded. How to synchronize or import/export files(images/music)?  Fact is need to update

  I have the macbook pro (OS 10.6.8) and the iphone 6 s. The latest version of iTunes is 11.4. When it is connected to the MAC, I get the message that itunes must be upgraded. How to synchronize or import/export files(images/music)?  Fact is need to update itunes?

  Hi sonalnj,

  I understand that you cannot synchronize your iPhone as iTunes is requested it must be updated. I can help you with that.

  According to the technical specifications for a 6 s iPhone, you need a Mac running OS X v10.8.5 or later version with iTunes 12.3 or later. Because you are on OS X 10.6.8 your version of iTunes is up to date with this OS.

  iPhone 6 s Tech Specs
  http://www.Apple.com/iPhone-6s/specs/

  Now to fix that, you need to update your Mac OS X 10.8.5 Mountain Lion or OS X 10.11 El Capitan. If you want to go to the Mountain Lion, you can do it with the first link below. The cost will be $19.99 and a code will be delivered to you if you can download it via the Mac App Store. Once you have upgraded, be sure to make all software updates to go with him to get the latest version of iTunes.

  OS X Lion mountain
  http://www.Apple.com/shop/product/D6377Z/A/OS-x-mountain-lion

  Now the other option is to move to OS X 10.11 El Capitan, and is a free update that you can do right in the Mac App Store, if you meet the system requirements. Take a look at the following article for more details on how to do it.

  Update of OS X El Capitan
  https://support.Apple.com/en-us/HT201475

  Nice day!

• my iphone hangs when I try to open the content of the email

  my iphone hangs when I try to open the content of the email

  What ios version do you have? It's 9.3? Because there is a bug in the most recent update, which can freeze your mail and Safari.

  Apple should have an update out before the end of week

  Fingers crossed

• Satellite M100-165: connection to the LAN operarte correctly

  I have a Satellite M100-165 for about 2 years with the original Setup (win XP etc) and I make all updates.
  The problem is that the connection to the local network is working properly from the beginning.

  I can connect only if I set the NIC property "link speed & Duplex = 10 Mbps Full Duplex", but on some LANs operate at all.
  I appreciate any response.

  Thank you

  I'm a bit confused now. What you mean with connection to the LAN working correctly from the beginning? What is started for you?
  I can't believe that you declare on that now, two years later. Have you already tried to install recovery image and test it with the factory settings?

• gen64.exe Malware when it is connected to the internet

  My desire to HP dv6-7206tx with Windows 8.1 has a problem when it is connected to the internet. An application named 'gen64.exe' makes the CPU to run at 100%. And Microsoft Security Essentials doesn't pick it up as a malware. I checked on the internet to confirm that it is a malware. Please help me. I have no idea how he broke into my laptop.

  Hello

  There are many programs for cleaning system of malware, adware etc which would suggest Members here.

  I like this one to detect & fixing malware: https://www.malwarebytes.org/mwb-download/

  Update latest version & tick "Scan rootkits" before starting the analysis.

  After the scan, quarantine the detected objects. Restart the system. Yet once, open the Malware Bytes program, go to the history tab in there: remove all quarantined items from there

  Restart the system.

  Open the prompt as administrator, do a SFC SCAN, check if integrity violations are:
  http://www.eightforums.com/tutorials/3047-sfc-scannow-command-run-Windows-8-a.html

  Concerning

  Visruth