Satellite A200-1VP: Installation of recovery could not be performed

Similar Questions

• Satellite A200-1VP - new WiFi card does not work

  Hi all

  I just bought an intel 4965agn wireless card to replace the original card intel 3945abg. I bought the card on ebay, it's a computer dell laptop.

  I installed it (connecting the black wire on pin 2 and the white wire to Terminal 3). The device appears in the device manage correctly without any problem. I installed the latest driver from intel for this card.

  the problem is that no wireless connection cannot be captured. the utility intel built in diagnosis, the card seems to fail the test of material. The section troubleshooting said to check the Device Manager and install the appropriate drivers. I've done it before, so I'm not sure of the problem.

  any ideas?

  Thank you

  Hi ansarali,

  Why you traded a new WLAN draft N card if you can t use it? I want to say that your laptop was only equipped Intel abg card and for standard project you also need 3 antennas and as much as I know Satellite A200 are not equipped with 3 antennas

  In addition, the antenna cables must be connected correctly. This means that you must connect the white cable to the HAND and the black cable to the auxiliary voltage
  Check this box!

• Satellite A200-1VP - Trackpad and the control volume

  Hello

  for the first time posting here so apologies in advance if I posted this topic in the wrong place or have not included all relevant information.

  My question is about a Satellite A200-1VP I bought recently from a friend. Model number PSAE6E-08D02YEN. The laptop has been completely annihilated and installed Windows 7 Ultimate before being redeemed.

  This seems to have brought the track pad and volume control to stop working.
  Are there drivers available that I could try to help to solve this problem?

  Thanks in advance.

  Hello

  I checked on http://www.toshiba.eu/innovation/download_drivers_bios.jsp Toshiba download page, and as I can see it, your machine is fully supported for Win7 32 bit, so you need to do is install all available drivers, tools and utilities.

  What version of operating system are you using (32 or 64 bit)?
  You have installed all the drivers?

• Satellite L500D - Iinitially had a problem "could not load the profile.

  Satellite L500D initially had a problem 'could not load profile' then stop. It is now the windows installation discs that I don't have. Where can I get them? They can be downloaded from Microsoft or Toshiba sites?

  Error message:
  File: \boot\BCD
  Status: OxcOOOOOOf
  Info: an error occurred while trying to enter the boot configuration data

  ANY HELP WILL BE GREATLY APPRECIATED THANKS

  Hey Buddy,

  > They can be downloaded from Microsoft or Toshiba sites?
  No, the disc can t be downloaded because it s not for free.

  You can start in safe mode?

  In the worst case operating system is confusing to the top and you have to reinstall Windows, but so you can take the Toshiba Recovery disk that will restore your notebook back to factory with all the drivers and tools of Toshiba.

• I get an error message saying 'installation of Windows could not configure Windows to run on hardware on this computer.

  I get an error message saying 'installation of Windows could not configure Windows to run on hardware on this computer.

  Installed the new hard drive on my Toshiba laptop and when I ran my recovery disk, Windows Vista installed, but when I restarted computer I get an error message saying 'installation of Windows could not configure Windows to run on hardware on this computer.

  Help, please.

  Hello
   
  
  Your error message, the problem is probably caused by BIOS or DVD settings or bad cabling to SATA hard drive. Please do the following to narrow down because of the problem.
   
  (a) ensure that all laptops the same hardware, the same manufacturer and the same model.
   
  (b) upgrade the BIOS to the latest version; go into the BIOS and enable "Load Fail - Safe Defaults".
  http://Windows.Microsoft.com/en-us/Windows-Vista/BIOS-frequently-asked-questions
   
  Warning of the BIOS:
  BIOS change / oxide of additional metal (CMOS) semiconductor parameters incorrectly can causeserious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.
  
  (c) If you connect the SATA drives, please configure the SATA controller in compatible mode in the BIOS.

• an installation support file could not be installed a catastrophic failure

  my laptop runs windows vista, a long time ago, I installed a game pc on this subject, I uninstalled later from the Windows UNINSTALL or CHANGE a PROGRAM but I noticed that an icon remained in the list of programs, but I do not put attention to it, a few days ago I tried to install the same game again , but when I click on the INSTALL option, AN INSTALLATION SUPPORT FILE COULD NOT BE INSTALLED CATASTROPHIC FAILURE message appears immediately, I tried to uninstall the icon that remained in the list of programs, but I can't I just get the same message... can anyone help me pleaseeeeeeeee

  Try the following two programs to remove it.
  If this fails, contact Support about problems with their software game maker:

  http://www.revouninstaller.com/

  Revo Uninstaller helps to uninstall software and remove unwanted programs installed on your computer even if you have problems uninstalling and can not uninstall it from Control Panel ' Windows Add / Remove Programs ".

  Revo Uninstaller is a much faster and more powerful alternative to "Windows Add or Remove Programs" applet!

  With its advanced and fast algorithm, Revo Uninstaller analyzes an application data before uninstall and scans after the uninstallation of an application. After that program's regular uninstaller runs, you can remove additional unnecessary files, folders, and registry keys that usually remain on your computer. Even if you have a broken installation, Revo Uninstaller scans for an application data on your hard disk and in the Windows registry and shows all the files, folders and registry keys so you can remove them.

  With its unique "Hunter", Revo Uninstaller offers you some simple, easy to use, but effective and powerful methods for uninstalling software. You can use it to manage your installed or running software.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://www.CCleaner.com/

  CCleaner is a freeware system, privacy and cleaning tool optimization. It removes unused files from your system - allowing Windows to run faster and freeing up space on the hard drive. It also cleans traces of your activities online such as your Internet history. In addition, it contains a complete registry cleaner. But the best part is that it's fast (normally taking less than a second to run) and contains NO Spyware or Adware! :)

  See you soon.

  Mick Murphy - Microsoft partner

• An installation support file could not be installed. The system cannot find the specified file

  I'm trying to get rid of some programs on my Windows xp, but the following alert continue to flock to the top: an installation support file could not be installed. The system cannot find the specified file

  Hello

  • What programs you try to uninstall?

  You can check this link:

  Problems installing and uninstalling programs on Windows computers

  http://support.Microsoft.com/kb/2438651

• Error 1720. There is a problem with this windows package install. a script required fpr this installation to complete could not be run.

  Error 1720. There is a problem with this windows package install. a script required fpr this installation to complete could not be run. Contact your provider to support personal or package. action Coustom DelAppData error script-2146828283. Argument or appeal of Microsoft VbScript runtime error: invalid procedures: "Left" line 22, column 1.

  Contact the technical support for the program that you are trying to install. MS - MVP - Elephant Boy computers - don't panic!

• error message when removing a program "an installation support file could not be installed, the system cannot find the file specified" _

  Try to delete a file from the Program Neighborhood Agent, so I can load a different version.  When I try to remove the program through the Control Panel, it says "an installation support file could not be installed, the system cannot find the file specified."

  Hello rarif, welcome.

  I recommend that you try and that you use the Windows Installer Cleanup Utility (WICU).

  1. go in:
  http://download.Microsoft.com/download/e/9/d/e9d80355-7ab4-45b8-80e8-983a48d5e1bd/msicuu2.exe

  2. download the utility and install it
  3 run the utility from START > all programs > Windows Installer Cleanup...

  4. find the program you want to uninstall, then remove the
  5. next, restart your computer

  Let us know if this helps,

  Thank you! Ryan Thieman
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• "Installation of Windows could not configure windows to run on a hardware on this computer."

  I recently released and bought 4 hard to present itself as a raid 10 disks, now I use my motherboards onboard fakeraid an ihc10r. The cables are fine and when I try and install windows 7 (64 x pro) on each disk with raid and ahci disabled in the bios, windows installs fine. Now when I raid raid 10 disks windows install can see the drive and even then, I load the drivers just to be sure that iastor.sys etc. (I tried with and without) is the same every time after the first reboot, I get about 10 minutes and 2 minutes after the resolution of the screen is adjusted BOOM "installation of windows could not configure windows to run on a hardware on this computer."

  First of all, then someone please help me get windows installed on my raid?

  Second, microsoft, your error messages leave much to be desired, it does not yet add a message in the Setup error log.

  EDIT: Forgot to add that I did a memtest and it happened, I also have the piece of garbage jmicron on my MB off the power. In addition, the facility produces when the SATA controller is in AHCI mode, BUT not in raid mode.

  Seems to me that if the software/driver is not compatible Windows 7. Also if any of the readers have reminants of your installation for each individual unit, Windows 7 may not be able to deal with formatting during the installation process. Try to download CD bootable diagnostic of the manufacture in car and do two things.

  (1) check each drive individually for issues.

  (2) wipe the drive (WD can for example remove the first and last part of the training which completely removes the MBR and other reminants for the final result is the drive looks like you just removed from the box and plugged in for the first time.)

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.

• "Cannot install the printer. Operation could not be performed. error 0x000003eb.

  I'm running Windows 7 (not Vista) and trying to install a Kodak printer driver and get "cannot install the printer. Operation could not be performed. error 0x000003eb"I searched constantly everyday for a fix. You have a solution other than what answers are already in this forum.  I uninstalled and reinstalled tried wireless and usb, installation driver separately, tried to install it in safe mode, run now utility scan.  I think that the problem began with an update of Windows 7 which has hung up and eventually having a corrupted file?

  Hello

  What is the exact model of the printer number? I suggest you to check if the printer is compatible with Windows 7: http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx If the printer is compatible, then uninstall all the drivers connected the printer to the computer, download the latest drivers from the website of the manufacturer, the install without connection to the printer. Connect the printer when it prompts. If the problem persists, contact the printer manufactrer for assistance http://support.en.kodak.com/app/contact/selected/true For more information see: http://support.en.kodak.com/app/answers/detail/a_id/1258/kw/Unable%20to%20install%20printer/related/1/selected/true Note: The use of third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

• Equium A60-191: 'request could not be performed because of an i/o device error. "

  I have an Equium A60-191 my dvd drive has stopped working, the led on this subject is on all the time like his who seek constantly.
  It does not read the CD or dvd and gives an error "REQUEST COULD NOT BE PERFORMED DUE TO A DEVICE IO ERROR.

  I tried to remove and reinstall the drive from the Device Manager, it doesn't help. I also tried to boot from the drive computer, but does not start, so I think that the drive does not work.

  I also noticed that the motor does not work in the reader, because that drives don't spin. Device Manager indicates that the drive works properly. Anyone know what is this error?

  1. click on start
  2. right click on my computer
  3. Select manage from the menu that appears
  4. in the computer management window, select Device Manager
  5. in the right pane, click to expand IDE ATA/ATAPI controllers
  6 identify your CD/DVD drive in the menu expanded and right click on the appropriate drive
  7. Select Properties
  8. in the Properties window, click the Advanced Settings tab
  9. in the Transfer Mode box that represents your CD/DVD drive (typically device 1), open the menu drop down and select PIO only
  10. click OK and exit all windows.

  If this does not solve your problem, then you need to go back using the procedure above and change device 1 to #9 step will support to 'DMA if available '. Then, change the device 0 to "PIO" only in the Transfer Mode box.

  Device 0: Primary IDE Channel
  Unit 1: Secondary IDE Channel

  Of course, he could also be dead DVD player. In this case, a new drive should solve the problem.

• Operation could not be performed. The print spooler service is not running

  I get the error message "operation could not be performed. The print spooler service is not running. "How to start the service on Windows xp print spooler?

  Click Start--->run---> Type ' services.msc"--->OK and scroll down to print spooler entry and right-click, select Properties, set Startup type and in"service status", click the button to start the service."

  Good luck.

• copy error: error 0 * 8007045D: the request could not be performed because of an i/o device error

  When copying the files, I get this error which is lower than
  an unexpected error prevents the operation.make a note of this error code, which might be useful if you get additional help to resolve this problem:
  error 0 * 8007045D: the request could not be performed because of an i/o device error
  filename DSc02828
  file type jpg
  size 3.27 mb
  updated the 09.11.2012
  try to jump again cancel
  Whats wrong here

  Hello

  Thanks for posting in the Microsoft community!
  You have reached the right forum for your question.

  1. don't you make changes on the computer before the show?
  2. where exactly you are trying to copy the file?

  Run check disk on the computer.
  a. click Start , and then typecmd.exe in the start search and then press ENTER.
  b. right-click on cmd.exe and clickrun as administrator.
  (c) in the command prompt, type the following command and press ENTER.
  Chkdsk /f
  Note: You may be prompted by a yes / no question. TypeYes and press ENTER.
  d. restart the computer so that the disk check starts. It will take about half an hour to complete the process of error checking. Do not restart the computer when the current disk check.
  Note: when running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost
  
  Summary the link:

  Error message when you try to perform a full backup on a Windows Vista-based computer: "the application cannot be performed because of an i/o device error."
  http://support.Microsoft.com/kb/952272

  Just reply with the results. I'd be happy to help you further.

• Error message: the request could not be performed because of an i/o device error. (0x8007045D) while performing the backup does not back up Outlook

  Original title: Outlook backup problem

  I support my computer using an external hard drive.  "It does not backup Outlook, declaring: the request could not be performed because of an i/o device error. (0x8007045D).  What should I do?

  Hello

  1. How did you perform the backup? He used the Windows backup and restore functionality?
  2. you have any third-party backup software installed on your computer?
  3. have you done any software or hardware changes on your computer before this problem?
  
  To work on the issue, check the following link.
  
  Error message when you try to perform a full backup on a Windows Vista-based computer: "the application cannot be performed because of an i/o device error."
  http://support.Microsoft.com/kb/952272
   
  CHKDSK warning:
  Important: When running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.
   
  See also:
  Back up your files
  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-your-files
  http://www.Microsoft.com/athome/Setup/backupdata.aspx
  Hope the information is useful.