Satellite A30 does not return after hibernation.

Similar Questions

• Satellite A30 - does not start after the RAM to level

  Hello

  I recently installed a crucial for memory
  my laptop, which is a Toshiba Satellite A30. However, when I try and
  restart the laptop, he tries to restart the fan turns on then turns off with a beep sound and this is not
  even to get to the Toshiba start screen.

  The memory I installed is 1 GB, 200-pin SO-DIMM, 128 X 64, DDR 333, CL2.5, part number CT12864X335.

  "Memory module PC2700 DDR 1 GB, 200-pin SODIMM

  CT12864X335
  
  
  * Size of the module: * 1 GB
  * Package: * 200-pin SODIMM
  * Function: * DDR PC2700
  ' * Features: * DDR PC2700 • CL = 2.5 • unbuffered • NON-ECC DDR333 2.5V • • • 128Meg x 64 •.

  I have
  took out and put back the old memory and the laptop boots
  normally and is OK, I even tried to put the memory in different
  slot machines, but it still has the same problem.

  This suggests that memory is faulty, as bought crucial memory must be compatible with my laptop?

  Thanks for your time,

  You have this problem if you use modules or only the new module?

  If you only use the new module, the case is clear. The new module is defective or is not compatible with the laptop.
  I think you should get back on the computer dealer and request a new. Maybe you can get a Kingston module because I have only good experience with this production.

  If you use both modules, they are not compatible. You should only use the modules with the same specifications.

• Satellite Pro A100: Screen does not return after hibernation

  The laptop went to Hibernate, but would not re - awaken.
  tried to disable following the manual, but the screen is now definitely blank, any suggestions?

  Hello

  The update of the graphics driver is not bad idea but Stefan, how should Christian update the graphics driver if it s not able turn on the laptop?

  I suggest putting the laptop turned off (press the power button for about 4 seconds) and unplug the AC adapter and remove the battery for a while.
  After several time (10-30 min), you can try to put the battery in the laptop and connect the power adapter. Then try to start the laptop.
  If it helps, then you could try updating the graphics card driver.

  In addition if the new BIOS version is available if you could also update it. But don't forget to use the good BIOS and the correct procedure for updating the BIOS.

  Good luck Christian

  Good bye

• Laptop does not return after hibernation or standby

  original title: cell phone crashes

  When mobile switch off switch on if necessary takes a few attempts before it lights up as if it blocks wile its judgment

  After that you have managed to turn it back on, do the following:

  1. make sure that the computer is virus-free
  Use Malwarebytes:
  http://www.malwarebytes.org/ ... pickthe free version.

  2 run a file system check to ensure that none of the corrupted files.
  http://www.Vistax64.com/tutorials/66978-system-files-SFC-command.html

  3. run a disk check for corruption and possibly repair errors and bad sectors on the hard disk.

  Start button > Search box, type cmd > look up, right-click on cmd.exe > Run As Administrator > in the black and white window, at the command prompt flashes, type chkdsk/f/r > press the Enter key.
  Note: there is a
  space between 'chkdsk' and ' / '.
  The screen will say something like cannot do it now, but you want to run it on reboot. Click on 'y' as in Yes > press > window cmd of output.
  Restart your computer. It will take a while. DO NOT stop the machine. Just wait.

  4. optimize performance
  http://support.Microsoft.com/kb/959062

  http://Windows.Microsoft.com/en-us/Windows-Vista/ways-to-improve-your-computers-performance

• Satellite M100-164 display does not illuminate after hibernation

  After the computer wakes up from hibernation by lifting the display panel (cover) and the LCD screen turns off due to power management settings, display shows the Toshiba logo and does not return after a key is pressed and the keyboard is not responding.

  I turned - power & removed the battery without success-.
  OPS: windows XP.
  Help, please.

  Hello

  You have removed the battery but wait you a bit?

  If please plug the laptop and remove the battery.
  Wait 15-20 min and then plug the AC adapter and put the battery in the laptop.

  Then try again!

• Satellite A30 does not start

  I hope someone could help. My A30 does not start although DC is green and the battery charges (amber). There is no beep or Flash. I removed the battery and tried to start on the current. Did not work. (75% frustration level) Heeeelpppp

  Hi Serkan,

  Do you see the Toshiba "splash" screen when you try to turn on your A30? If this isn't the case, then it is likely that your motherboard has failed, and you will need to refer to an authorized Service partner.

  If you see the 'splash' of Toshiba screen, but your portable computer does not load its operating system, then it is likely that there is a problem with your hard drive.

  Kind regards

• Satellite A30 does not start with the USB device connected at boot time

  Hello

  I have a Satellite A30 and sometimes it does not start.
  After turning on, not even the BIOS starts.
  even if sometimes the BIOS starts, but the OS does not load.

  I figured out that its related to USB devices connected at boot time.
  If no USB devices are connected, it starts without a problem.
  Even if the start-up is suspended, as soon as you unplug start it BIOS USB devices.
  Its ok to connect USB devices later, once the system has started.
  I disabled "removable devices boot" and "network startup."
  just in case, but it makes no difference.

  BIOS is version the most recent (1.70) and it comes up with all kinds of USB devices.
  printer, mouse and (self-powered) external USB hard disk.

  Is this a known issue?
  There is no known workaround solution?

  Hello

  I put t know why this happens, but it has to do with the BIOS.
  The same thing happened on my old laptop. I couldn't start my unit while the USB printer has been turned on and connected.
  The only solution is to disconnect the external USB device during the boot process.

  RSY you should check if the order of boot in the BIOS has been on the HARD drive first.

• Satellite A30: Does not recognize USB devices.

  My computer does not recognize any devices when connected to the USB Port on my Satellite A30. After downloading SP2, I was able to install the printer, but I can't use it because there is no printer icon in the toolbar. If I want to print something I get the window of the printer, select printing, then it goes to the author of the Image of MS Office. Basically, I can't use my printer or any other device connected to a USB port.

  However, it was working perfectly fine when I had the home edition of XP but I can not reinstall this one because there is something wrong with the recovery disk that's why I had to install XP Pro.
  Also, I used to get a sound, letting me know that a device has been connected. I get more or the icon in the toolbar.

  Is that what I could do to fix this please? Is it possible to get another disc of recovery somehow? Obviously, it's something to do with XP Pro software, but I don't know what to do.
  Could you please help me?

  Thank you!

  Hello

  If you get a window of the printer you need to select the right printer. If printing goes to MS Office Image writer so the right printer is not selected.

  On the new installation: If you install the operating system from the original Windows CD you must install the necessary drivers and QFE patches all in the right order.

  USB port: I found a useful paper on this topic:
  http://support.Microsoft.com/kb/873169/en-us/

  Good bye

• Portege M700 Wacom does not respond after hibernation

  I've been using the M700 for two months and I met a very annoying bug. It is not mentioned in this forum so far, but there are other reports on the Internet who mention this problem too. (http://forum.tabletpcreview.com/showthread.php?t=16902)

  * Question: *.

  Tablet is placed in hibernation. When he wakes up, everything seems OK. When you use the stylus or the key functions, that the cursor does not move. Tablet and pen services have not crushed, but there is no link between screen/digitizer and software.

  + Technical support +.
  The series/USB connector is not reset after waking or hibernation is dead the serial connection

  * I tried solutions *.
  So far, I have reinstalled Vista, tried XP (and will stick to it because it's a better OS in many cases) and have reinstalled all kinds of drivers Wacom.

  * What we want *.
  Wacom has also seems to be aware of the problem but says it's a matter of Toshiba. I am impressed with the construction and the quality of the M700 (it is a replacement for my robust but now almost unusable M200 and I have a M400 too, but I never liked it) and this issue is the only glitch I meet.
  I would like to know if anyone else in this forum has experienced a Wacom-coma after the resumption of the hibernation or standby, and if so, if they have found a solution (apart from restarting their PC)

  And I would really like a response from a representative of Toshiba review of this question.

  Hey Buddy

  I m not a M700 owner and, therefore, I can not say much about this issue, but to my knowledge, there are a few different problems with Vista and hibernation mode.
  For example, device high definition audio, screen WLan failed after the resumption of hibernation.
  These issues were definitely Vista problems.

  Installed on Portege M700 Tablet d River was developed by Wacom, I wonder why the guy States that it is a Toshiba issue?  :| (perhaps because this Toshiba laptop s ;)))

  Anyway, you said that you have reinstalled the driver for the tablet of the Toshiba page and updated the Vista of the State. Check the BIOS updated maybe he could improve the functionality

  If this does not work I recommend you contact the ASP to find out if there is a known issue

• Re: Satellite L30 does not start after adding another stick of 1 GB memory

  I bought 1 GB PC4200 533 MHZ DDR2 SODIMM memory module for my Toshiba Satellite L30 - 10v (PSL33E) to make it 2 GB. After you have added the 1 GB modules Satellite L30 wouldn't start. With only 1 GB, that it starts ok, with the other 1 GB origianal only boots ok. (The two modules are ZCE6 430 - K4T1G163QB Samsung 1 GB PC4200 533 MHZ DDR2)

  The two modules of 1 GB boot not together. I noticed that many others have had this problem. (please see
  This [t-22984]. post)
  On this forum, someone bought the CT12864AC53E memory module which works, however I can't find this on the site of Crucial.
  I've heard other purchase the sticks of memory CT572238 and CT572234 and have the same problems.

  Memory Advisor says determinative buy the CT572234 memory sticks.

  I have also updated the bios to V3.10, still does not start with the two modules.

  I'm ready to buy 2 new modules, but what 2x1GB memory works?
  Any help would be greatly appreciated...

  Post edited by: quigs1969

  > 1 GB strips boot not together. I noticed that many others have had this problem.

  For me it s case;
  The two modules don't work together
  Seems the modules are not compatible there is only one solution. Replacement of RAM!

  Try other RAM modules.
  I bought a few modules from Kingston and made good experience

• Satellite M45 - does not start after restoration on the new HARD drive

  I installed a new PATA 250 GB HDD on my pc. The BIOS is configured to boot from CD/DVD. Toshiba Recovery disk started cold, start follow-up statement to load a new system on the HARD drive. He made a (quick) format on the HARD drive, spent 50 minutes, copy the files from the CD to the new HARD drive. Followed the instructions to remove the CD and reboot the pc. Did. I get the Toshiba homepage for 2-3 seconds, and then I get a white screen with a white block cursor in the upper corner of the LH of the screen. Looks like it does not find the block on the HARD disk?
  The procedure of collection 3 times with the same results. Checked the BIOS to check that it is configured to boot from the HARD disk after installation.

  The recovery CD is blank. Never used because I bought the PC (3.5 years). Put the new HARD drive in a USB enclosure and formatted with Windows, tried again with the same result? Put the old HDD, PC starts and works very well. Put the live CD Knoppix and boot from that, works very well. See the new HARD drive.

  Thus, any suggestions are appreciated. The recovery CD Toshiba is defective? In any case to test?

  Thank you
  -J

  Hello

  Sounds like a problem with the recovery disk or the new HARD disk if your computer starts up fine with the old HARD drive...

  In your case before you start a lengthy discussion, you should try a Microsoft Windows disk to install Windows. If he work it seems that only the recovery disk is defective.

  Otherwise, the HARD disk must be defective. Maybe a bad sector or something else

• SP6100 does not start after hibernation

  Hi, I'm in trouble. We have here a SP6100 which went into hibernation.
  Now we are unable to bring it back to live. When you press the power button, only the far left led flashes orange.
  Even pressing the power on button for 10 sekonds does not stop, start or do ANYTHING.
  The screen remains black, no logo or anything like it either appears.
  As I am in the middle of nowhere (Sierra Leone) with the next Center about 4000 km (not no joke), I have to solve it myself. What would - they in a repair center? I'm known in technical terms. So I can just unscrew if necessary. Where should I start?
  Any help welcome!
  How to remove battery from the bios clock? Where is that?

  Hello

  Can you please tell me if this blinking is consistent and uninterrupted or there is some sort of Morse code (orange flashing)?

  If there is an excessive flashing there may be some malfunction of the equipment. If the power supply microcontroller detects an error lamp DC IN sends a blink code.

• Satellite A30 does not see other devices in the wireless network

  I recently bought a Toshiba Wireless LAN Mini PCI Card, I installed and was able to recognize my broadband, but he does not see the other network devices. I have not provided with drivers or software for the operation of the card (I bought a decent retailer). Can you recommend me to downloads that would be this card?

  I have a laptop of Satelite A30 1 GB ram 60 GB HDD.

  Large files sometimes also stop transfer (crashes) when you use my USB connection. The usb controller uses the driver microsoft 5.1.2600.0 dated June 1, 2002.

  Is this a driver problem?

  Hello

  If the wireless network adapter is properly installed if you have not configured you.
  I put t know which devices in broadband services, you want to say but generally if you want to communicate or transfer files between laptops through the WiFi network so all the computers must be in the same domain or workgroup.

  I can't give you a correct answer, but only a suggestion. I have red that sometimes a lower potency could be responsible for this show. Try turning off the safe power option in the properties of the hub USB root in Device Manager.

  Hello

  If the wireless network adapter is properly installed if you have not configured you.
  I put t know which devices in broadband services, you want to say but generally if you want to communicate or transfer files between laptops through the computer WiFi network so all must be in the same domain or workgroup.

  I can't give you a correct answer, but only a suggestion. I have red that sometimes a lower potency could be responsible for this show. Try turning off the safe power option in the properties of the hub USB root in Device Manager.

• Satellite A50 does not work after BIOS update

  Hi all
  I tried to Flash my BIOS through windows such as recommended on my website of the manufacturer of the laptop (Toshiba). I guess that the process was not as after only 2 hours still "don't interrupt" message displayed. I had to force power off of my PC. Now it is not initialized.
  The Laptio is Toshiba SA50-114, series of satellites. Model n - PSA50E

  I tried the suggestions in the following link
  http://askiris.Toshiba.com/ToshibaSu...200%2035586212
  However, it did not work.

  However, I don't have the disk recovery and file/ROM BIOS tool. Have tried to search on the internet, but without any result.

  Can someone help me please
  1. How can I update the BIOS to get my PC to running back.

  2. to turn towards links where I can find the files in the link above.

  Thanks in advance.
  Best regards
  Parag

  > 1. How can I update the BIOS to get my PC to running back.
  Not possible if your ROM BIOS module was bad flashed.
  If you are a lucky man only the ROM module must be flashed again using a special procedure. But this can be done by a service provider authorized in your country.

  > 2. Point me to the links where I can find the files in the link above.
  There is no link! You need to ask to help ASP.

  Good bye

• Win XP on Satellite M30X does not start after battery was flat

  XP on M30X will not start after battery was flat! Safe mode, last work... nothing works!
  The restore CD offers 3 options1: new installation, 2 toshiba recovery utility (expert mode) und 9 output.

  How do the XP Recovery console, or how to use 2 to restore the system without losing any files.

  Thanks for the tips.
  It is a nite Mare...

  Wolf
  Good day

  The point is that the Toshiba Recovery CD does not have the Windows XP repair console.
  The restore CD contains the image of Toshiba and you can just reinstall the system on the HARD drive and no repair.

  Now you have 2 options of recovery.
  First called standard recovery option would be to format the entire HARD drive and reinstalling the image.
  The second option called recovery expert allows you to reinstall the operating system on a selected partition. Then only this partition will be formatted.

  If you do not want to format the whole HARD drive then you select the second option and select the partition to a new operating system.