Satellite A660 - beep when the CPU is not loaded

Similar Questions

• Satellite A660 - 11 M: the display does not work with nVidia drivers

  Hello world.

  First of all:

  I use the default pre installed SB (w7-64) and nothing more is installed on it, except the toshiba software.

  The problem is that, while I use the default driver installed that everything works well, if I update the nvidia drivers, I can't change the brightness more.

  It cannot be changed by fn + f6/f7
  cannot change it in windows through "brightness".
  no change in the power management profile.

  (I can put different brightness levels, but nothing is happening!) (I hope you understand what I mean)

  the only way to do it is using nvidia Control Panel.

  even if use windows utility to update windows drivers download the same drivers and there is the problem.

  the only way to fix it is to reinstall the default driver.

  but I don't want to use the prehistoric driver!

  How can I do to fix this? is this a known issue?

  Thank you very much for your help!

  Hello

  Since the nVidia page nVidia drivers are not pre-tested and not certified by Toshiba, it s not recommended to use these drivers.
  You must use graphics drivers of Toshiba because the drivers are modified and created for the use of the laptop. These drivers support own device of thermal protection that protects the graphics chip.

  I think that the issue has nothing to do with the Toshiba FN button software because brightness can be affected, even using Windows 7 power management

  I recommend to go back to the original drivers Toshiba!

• ProBook 6440 b: cannot upgrade to Windows 10 - "The CPU is not supported" error message

  Hello everyone

  I have a HP ProBook 6440 b. CPU is intel core i7 M640. It is currently running Windows 7 64-bit edition. I'm trying to update to 10 Windows using Windows 10 Upgrade Wizard and it gives me error. It says "Windows 10 does not work on this PC. The CPU is not supported (NX). »

  Any help will be appreciated. Thanks in advance.

  Hello:

  I suggest that install you the upgrade from the DVD (authoring tool of your own from the link below - media Make).

  https://www.Microsoft.com/en-us/software-download/Windows10

  The DVD will bypass the hardware checks.

  Also, when you install W10 from the disk, skip verification of updates when you are prompted.

• How to stop a beep when the loop ends

  Hello

  I have a beep occurs inside a loop (which contains waves of data acquisition) to a certain threshold. I want the sound system for not introducing any delay in the execution of the loop.

  But I also have another beep when the loop ends. How to eliminate this noise?

  Your comments will be greatly appreciated. Thank you

  PI

  The obvious answer would be: remove the beep VI this is probably. Please show us your code.

• Firefox seems to have recently developed seemingly random usually do not remember bookmarks, particularly when the pc does not stop correctly. Thank you

  Firefox seems to have recently developed seemingly random usually do not remember bookmarks, particularly when the pc does not stop correctly. Thank you

  If Firefox detects that the places.sqlite database is corrupted then Firefox can create a new database file and import bookmarks from a JSON backup that does not contain the most recent bookmarks (a new JSON backup is created when you run Firefox for the first time on a day), then you may lose the bookmarks in such a case.

  You can check for problems with the database places.sqlite file in the Firefox profile folder.

  • http://KB.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
  • https://support.Mozilla.org/KB/bookmarks+not+saved#w_fix-the-bookmarks-file

• no service to customer without having to pay when the product does not work?

  no service to customer without having to pay when the product does not work?

  You will need to tell us more of the history for anyone to be able to give advice. The WHOLE story would be great!

• How to change existing keywords when the site is not in the bookmarks bar?

  I've implemented several shortcuts keyword for sites that I use frequently. Now, how can I change the keywords or URLS when the site is not in the list of bookmarks? Is there a master file Firefox for these access which can be edited by the user? Or another way to get to them?

  Not sure if it's the same on Mac OS x, but it is how it is done under Windows and Linux versions of Firefox.
  
  Bookmarks > organize bookmarks
  
  Highlight the bookmark in the right pane, and then click more at the bottom to see the keywords and Description fields for this bookmark.

• Satellite A300 stops when the power adapter cable

  Hi people

  When I connect the power cable for my toshiba satellite a300, it stops immediately. I can use it on battery normally without any problems.
  When I boot in safe mode, it works fine without any problems with the AC adapter plugged into the laptop.
  Operating system is Windows Vista
  What is the reason? What can I do to fix this?

  Thank you

  Can you use it for laptop with AC power only when the battery is removed?
  If so, boot up your laptop and when the operating system is loaded to put battery inside, wait a few minutes and disconnect the power supply.
  Plug it in again and let us know if the same thing will happen again.

• Satellite L500D - Iinitially had a problem "could not load the profile.

  Satellite L500D initially had a problem 'could not load profile' then stop. It is now the windows installation discs that I don't have. Where can I get them? They can be downloaded from Microsoft or Toshiba sites?

  Error message:
  File: \boot\BCD
  Status: OxcOOOOOOf
  Info: an error occurred while trying to enter the boot configuration data

  ANY HELP WILL BE GREATLY APPRECIATED THANKS

  Hey Buddy,

  > They can be downloaded from Microsoft or Toshiba sites?
  No, the disc can t be downloaded because it s not for free.

  You can start in safe mode?

  In the worst case operating system is confusing to the top and you have to reinstall Windows, but so you can take the Toshiba Recovery disk that will restore your notebook back to factory with all the drivers and tools of Toshiba.

• HP ENVY x 360-15-w100nt: wi - fi connection slows down when the charger is not plugged

  Hello

  My wi - fi connection slows down when the charger is not plugged in. Correct the wireless lan drivers. So far, I appreciate all kinds of advice for this problem.

  Thanks in advance

  Hello @JohannNewma,

  Welcome to the HP support community! I read your post and wanted to tender hand can help you!

  I understand that you notice a decrease in speed wireless on the x 360-15-w100nt laptop computer ENVY when running off the battery voltage.

  You can check and adjust the power options on the system as it is probably trying to save battery power by reducing wireless performance.

  If you're still having problems, you can follow the steps described in this document to troubleshoot the network settings and internet wireless.

  Please get back to me how that happens. To show that you like, or are grateful for my post, please click the Thumbs up below.

  Thank you!

• do not display menu when the program is not running

  Hi, I did with an XControl I can start the program with a start button.
  I deselected the toolbar, Run and Abort button when runnning and the program runs with only a custom Menu, just like I want.
  When the program stops the menu and the toolbar is visible (as usual). My question is - can you choose not to show the menu and the toolbar when the program does NOT work?

  During execution of the edit mode, it seems reasonable to return to editing mode later.

  Once the program is distributed to end users, edit mode is meaningless. Built in a standalone application or at least to define its 'open operation' and close once. The program should never be in a stopped state. Create a state machine passing the State idle when it's not what anyone.

• How the LED lights up when a threshold is reached, then turns off only when the value does not reach the threshold for a while?

  Hi, I want to write a program that can turn on the LED when a range of value, this is the threshold and only when the value does not reach the threshold for a period of time, say 5 seconds, then the LED will turn off, otherwise it will remain. How can I achieve this in labview? Can someone help me? Really thanks!

  I assume that you use a while loop to keep the updated value.

  Add a record to offset to your looping it initialize with a U32 (time in ms)

  Add the registry to offset to your loop that keeps the previous value of your bool

  When your reaches the threshold value => the light and set the current time in your shift register.

  In the next iteration of the loop weather check value is still above threshold

  => Y-online previous set to true?

  => Y-online the next iteration

  -Online N => turn switch on and set the current time in your shift register.

  -Online N => subtract the time current less time shift record-online more then 5 seconds?

  => Is => keep turning on

  -Online N => turn given

• Why should keep the lid of the laptop closed when the laptop is not in use?

  Why should keep the lid of the laptop closed when the laptop is not in use?

  For energy conservation, to avoid dust and spills and damage the display.

• Capture of key press on when the focus is not on VI. (event does not work).

  I have a VI and found similar in Forums. I need to get the key to the bottom of the event, when the focus is not on VI.

  I have attached the VI found in the forum. Try clicking other windows, for example on the diagram of the VI, when VI is running and check if it works. The answer is no, it does not work. When you press a key, the button led should change its State, but it is only when the focus is on the face before of the VI. The question is how to control the pressure of touch, when VI is reduced or inactive. Is it possible to get the key to the low or any other similar event, when emphasis is placed on another application, not the VI?

  Take a look at the 'Connectivity... of input devices' menu.

  For an example, open the example finder and search for 'basic demo of entry. " It should give you some ideas. Good luck!

• G42-461TU: Laptop hangs when the charger is not connected in

  Hi all

  I use HP G42 - 461TU Notebook.I have a problem with my laptop. He often gets crash when the load increases. Once when the charger is plugged in, it works fine. But when the charger is disconnected, it gets even once block. I thought it might be due to problem of memory and I added extra 2 GB DDR3 RAM too (totally 4 GB now), but the problem persists. Now I use windows OS 10, but I faced this problem with windows 7 too. Can someone please help me diagnose the problem with my laptop? Thanks in advance!

  Hi @Dinesh_R,

  Welcome to the HP Forums! I read your post and wanted to help.

  I understand that your notebook crashes when the charger is not connected. You can start with this document: computers HP - computer is slow (10 Windows)

  Let me know if that helps the problem.

  If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me congratulations.

  Kind regards