Satellite L30-134 - LAN and audio driver problem

Similar Questions

• Satellite L30-134 PSL33E sound card driver does not

  There is no setup.exe for the sound card in the download?
  and it will not install manually with the inf file

  can someone point out the correct link for the drivers for sound card for this laptop

  Satellite L30-134 PSL33E

  Have you tried C:\Toolscd in the RealTek folder? I removed, because it takes too much space, and when I had the problem with the driver (I also Satellite L30-134), I downloaded from:

  http://support.toshiba-tro.de/tools/satellite/sl30psl33/XP/sound-PSL33-XP-51005273.zip

• Dynadock U3.0 LAN and Audio driver does not.

  Installed according to the instructions on the no fare of Lenovo IdeaPad U510 obstacles. USB and video ports works OK, but I have no ethernet connection and no sound.

  After checking the Device Manager, there is a problem with the drivers. But I can not find the drivers for the Ethernet and Audio... only for video :(

  I tried to reinstall the drivers on non-tariff barriers, but no effect...

  Please can someone help me?

  Thank you

  > After checking the Device Manager, there is a problem with the drivers. But I can't find the drivers for the Ethernet and Audio... only for the video

  There is no drivers for the sound or LAN. These drivers would be installed automatically by the Windows operating system
  The Dynadock supports own graphics chip and therefore you need to install the graphics driver.

  But if you don't have audio output, try this.
  Go to control panel of-> sound-> the Read tab
  Right click here and choose two options (display, devices see the disabled)
  Now you must select the default device for audio output.

  Regarding LAN:
  Try to transfer the authentication settings of the internal to the external network adapter.
  Open the properties of the internal network card and choose the parameters of the tab "authentication."

  Now check the option titled enable IEEE 802. 1 x authentication for this network
  Choose EAP type: EAP (PEAP)

  Also check the option called authenticate as computer when computer information is available

  After you apply the settings on this tab map LAN Dynadock, it should work without any problems.

  By the way: you can download here the Installation Dynadock U3.0 disc (it is the backup copy of the disk in the software box)

  http://www.MyToshiba.com.au/support/accessories/port-replicators/pa3927a-1PRP/download?OS=25

• Satellite L30-134 - after HDD upgrade PC freezes and won't start

  Hello
  I upgraded my Satellite L30-134 of the standard 60 GB HDD for a new 120 GB. After that, I have the following problem:

  (1) after installing XP form to the recovery House DVDs works fine but after that 2-3 weeks of normal use it instantly freeze pc and after hard reboot the OP start up can do anything but to format the HARD drive. After that format cannot install original XP and Vista, the progress bar show me that the installation is complete but after reboot, nothing happens. This problem persists long wery. After 3-4 clean up one after another the pc starts and runs very well about 3 weeks. What is the problem? Any idea?

  (2) when I first install Vista or Linux PC is runing fine, but not in normal parameters. Always freeze but after hard reset works fine for about 2-3 days. When I install XP first that the PC is useles after hard reboot the only thing I can do is to format the HARD drive and do a clean install.

  PS: The HARD disk is produced Original Toshiba.

  Hello

  This strange boyfriend s but to me it sounds like that, these problems are caused from the new HARD drive that may be defective.

  I think you should test the HDD using Hitachi Drive Fitness Test:
  http://www.HitachiGST.com/HDD/support/download.htm#DFT
  With the Drive Fitness Test, you can test your HARD drive. Download the CD image, burn it to a CD and boot from it. You can then the HARD drive test.
  On the same site is a user's guide if you want to know more.

  Good luck and give us feedback, what happened! :)

• Compatible drive for Satellite L30-134 (PSL33E-00E00WRU)

  Please indicate internal what HARD drive I should buy for my laptop Satellite L30-134 (PSL33E-00E00WRU)?

  Hello

  I found a similar thread here:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=51895

  As you can read you can install each 2.5 HARD drive with SATA interface. It is no problem and you don't need a certain brand. Just buy this model you prefer ;)

• Satellite L30-134 - question about upgrade CPU and video performance

  Hi have updated my satellite l30 - 134 with a bus t2450 dual core @2 ghz 533 Mhz = cpu is runing swell-marks look nice... BUT - my video performance droped a lot - grafics 2d - to top but 3d grafics are very poor why? driver problem?
  have also 2 g ram 2 x 1 g kinmax @ 6xx runing @533

  can anyone help? see that are some similar configs on this site... then maybe you can help me
  I'll try editing a xp 64 bit (curently runing xp sp3 32-BIT)

  > I'll try editing a xp 64 bit (curently runing xp sp3 32-BIT)
  Forget that don t recommend install Win XP 64-bit.
  Why? Because the Win XP 64 bit was not so popular as Win 32 bit or Vista/Win 7 64 bit and you won't find many drivers for Win XP 64 bit.
  Stay with XP 32 bit or you can change to Win 7 64 bit.

  Regarding the graphical issue;
  Have you noticed that also using the old CPU (Intel Celeron M Processor 410)?
  If this were not the case, then I guess this could be a problem between the CPU and BIOS.
  Otherwise I would recommend upgrading the graphics card driver.

• Problems upgrade memory on the Satellite L30-134

  I just bought 2 x 1 GB memory for my L30-134 PC4200 and installed that they work fine in the BIOS, see and read as they should do, but when windows starts up it will crash with the two modules are installed, don't ever get to the screen with the loading bar crossing and then I get the blue screen.

  I forgot to take note of the error code, I'm afraid... (Silly I know). If I remove one of the modules and module installation original 512 with just 1 the 1 GB ones that it works perfectly. BIOS has been updated to the latest version 3.10, and again, I get the same problem...
  because everything looks good go in the BIOS I think that its more likely to be a software problem (windows) any maybe some damage data in the registry or maybe a virus... anyone have any ideas?

  In addition, the laptop is actually my step son and he really wants to have the CPU improved Celeron 410 to one that is a little faster. When we look at first in this we was told that several processors are compatible (although not really worth the hassle of installation) they were cel m 450 2 GHz, dual core t2060 and t2080 pent, as well as the core duo t2250, so he bought the t2250 and it wouldn't surprise, or should I say it power on with no display and the stopcock and just epeated cycle. So didn't take is not a genius to establish it was not compat...

  I know the t2080 are used in of the L30 and 1.73 533 FSB with 1 MB L2 cache-65nm and do walk. The t2250 is identical apart from the L2 cache is 2 MB and deepening varies from c to MB depends on when you bought it... because oe it already has the CPU it will sell and use the money to purchase one that will work. If anyone has any info that could help to ensure that it doesn't end up going round in circles I would really appreciate it...

  Oh and just to make laugh you all he was member of staff line Toshiba tech that had told him that the CPU would not work and that the L30 managed to take 2 x 1 GB memory and not once mentioned that there may be problems with two updates...
  Issues such as neither soddin work... lmao

  Are you sure;?  :|

  On the website provided in your posts, I found this info:

  _Radeon Xpress 200M_
  Memory interface:
  -UMA mode operation requires no additional memory
  -* DDR and DDR2 Support *.
  -* DDR speed * up to the * 400 mhz *.
  -* Speed DDR2 * until the * 667 mhz *.

  _Radeon Xpress 200_
  Memory interface:
  -UMA mode operation requires no external graphics memory
  -+ Variants available with single or double channel system memory support.
  -* Support for DDR or DDR2 memory *.
  -* Memory DDR * speeds * DDR400 *.
  -* Memory DDR2 * speeds * DDR2-667 *.

  concerning

• Satellite L300 17L - audio driver problems

  Audio driver problems, I use Windows XP SP2, I installed the MS patches, but still there is no sound.

  And in the control panel in the sound section says that there is no audio driver installed.

  I need help please!

  Hello!

  It s a known issue and when you search a bit in the forum you will find a large number of publications on this subject.

  Remove the sound card from the Device Manager and the high definition Audio Controller from Device Manager.
  And then update Windows with KB835221 & KB888111 patch, reboot several times, and then you can install the driver from Realtek but download and install Realtek driver directly.

  Good bye

• Satellite L30-134 and Pentium M - is it possible?

  Hello

  Is it possible to place the Pentium M processor for laptop Satellite L30-134? This chipset is flat leading edge computer laptop?

  THX, Poland Rafal

  AFAIK the L30 comes with different 479 Intel Mobile processors.
  It supports Celeron-M as follows:
  Intel Celeron-m Dothan: 360J(1.40GHz); 370 (1.5GHz); 380 (1.6GHz)
  Front side Bus: 400 MHz

• Satellite L30-134 PSL33E: CD/DVD player can't read data CD

  I bought my laptop (Satellite L30-134 PSL33E) 4 months ago and I had no problem with the optical drive of my Satellite. But yesterday, I discovered that my drive is no longer can read data CDs.

  I created a CD with the Toshiba ToDisc utility which contained MP3s. The CD works fine on another computer but when I try to play them on this computer Windows laptop tells me that the CD is blank and asks me if I want to save data.

  It doesn't have this problem with the DVD, I can read and write perfectly. My optical drive is a CARPET * a DVD-RAM UJ - 841S. Windows says I have the latest driver for it (5.1.2535.0) but it says it's from 2001 (?) in the properties under the selected hardware.

  Help, please!

  Hello

  It is not easy to say what the problem is here. If you have time please check THIS document.

  Support Bulletin 98081245 CD burning: suggestions and troubleshooting. ‘

• Satellite L30-134 no sound through speakers using Win XP SP3

  Hello

  I have a Satellite L30-134.

  I just replaced the card mother and re-installed XP Home SP3.

  Everything is working great except the sound.
  It works through the headphone jack, but not the internal speakers.

  I tried new drivers from Realtek, Toshiba drivers, but still no joy.

  Can anyone help?

  See you soon

  rkid5846

  Have you replaced it one or it was done by the authorized service provider?
  Is replaced mainboard new or used?

  Sorry to ask this, but all this story is incredible. Speakers don t work but with a helmet, there is no problem. I put t have this model of laptop, but somewhere I saw similar thread and I believe in Realtek Sound settings (Control Panel) you can enable/disable headphone and speakers separately. Check under options Audio i/o.

  Maybe you'll find it.

• Satellite L30-134 - fail screen

  Hello!
  Hopefully, someone can help me with my problem.
  I had one laptop Satellite L30-134 and had no problem with it. But today tried to move on and the screen lights up. I can hear the winchester and cooler work for a min then stop.
  A few months ago, I had the same problem, but he left about an hour later.

  So, can you tell me what can be the problem and how can it be solved?
  Thank you
  Eniko

  Which may be caused by several reasons.

  Have you tried re-seats or try different Modules of memory?

• Unable to connect the mouse or the keyboard on Satellite L30-134

  Just bought new Satellite L30-134. Try to connect monitor via a belkin, switching, separate keyboard and mouse device. Keep an eye on fine, but the keyboard connection problem or the mouse. Both are connections PS2, I used PS2 to USB switching device. Sounds complicated, but I thought that it would be "plug and play". Whenever I connect keyboard or mouse, error message saying device connected unknown.

  ANY HELP APPRECIATED

  Thank you

  Mark

  Hello Mark

  Can you please try to connect to some new keyboard or mouse? May be time to use recent hardware components with new laptop models. Use some modern mouse and keyboard and it will certainly be "plug and play" device.

• Satellite L30-134 will not accept 2 GB of RAM

  I looked at my laptop and it takes a maximum of 2 GB of DDR2 RAM, I tried two different pairs of sticks of 1 GB and the two blue screen that loads the OS.

  When the sticks do not go it simply ignores the second run, but I can't seem to accept 2 GB.

  BTW I have upgraded to a core duo processor, don't give me no problem.

  Known fixes for this problem?

  Hello

  Your laptop can be upgraded up to 2 GB of RAM. That s is definitely possible!
  You can use 2 modules of memory vivid x1024MB.

  If you would taka glance at this page, you will find information that you must use the DDR2 533 MHz (PC2-4200) 200 - PIN SODIMM modules.

  [Memory for Toshiba Satellite L30-134 | http://www.orcalogi.co.uk/asp/prodtype.asp?prodtype=25737&ft=m&st=3]

  I presume that you always get a BSPD because the RAM modules are not fully consistent or simply malfunctioned.

  Welcome them

• Toll-free indicated what power disconnected from the Satellite L30-134

  I don't know it this the appropriate category, because I'm not sure of the source of the problem.

  Okay, here it is:
  I have Toshiba Satellite L30-134.

  Normally, when I unplug the cable of the AC adapter, 2 things happen:
  1 ATP icon shows that the current generator is the battery, and it shows invoiced % and about working time remaining before the battery is empty.

  2. the power management becomes more energy saving settings, and implementation Hibernate just until the battery is completely down.

  Well... Last few days things have changed:

  Now, when I unplug the power cable, the system does not recognize this and she continues to display: ' course Power Source: AC Power ', for the remaining capacity of the displays: "S/o" and the system is not hibernate, because he does not feel the difference.
  I'm not sure that this has something in common, buy, I found that the UPS SERVICE has been stopped, I tried to start it manually, but there is ERROR 2481: the UPS service is not configured correctly.
  Need help, please :-)
  OS: Windows XP, automatic updates, I did not notice if this happen after installation or any other measure of speciffic, I did...

  > Normally, when I unplug the cable of the AC adapter, 2 things happen:
  > 1. ATP icon shows the current generator is the battery, and it shows invoiced % and about working time remaining before the battery is empty.
  > 2. Power management becomes more energy saving settings, and implementation Hibernate just until the battery is completely.

  This process is correct. After disconnecting the AC adapter the laptop switches to the battery power and uses the Toshiba power saver mode the power created for the use of the battery.

  > Now, when I unplug the power cable, the system does not recognize this and she continues to display: ' course Power Source: AC Power ', for the remaining capacity of the displays: "S/o" and the system is not hibernate, because he does not feel the difference.
  > I don't know he has something in common, buy, I found that the UPS SERVICE has been stopped, I tried to start it manually, but there is ERROR 2481: the UPS service is not configured correctly.

  Well the ups (uninterruptible power supply) service could be responsible for this problem!
  If you are not able to start it manually, then it might be a problem with OS software.
  I studied a bit and found this article in the Microsoft Knowledge base about this problem.

  + Cannot start the UPS Service.
  http://support.Microsoft.com/kb/310437

  Good bye